kwikupproducts2014 (small)
-
Upload
sunil-datwani -
Category
Documents
-
view
41 -
download
4
Transcript of kwikupproducts2014 (small)
2014 PRODUCTS BROCHOURE
Suppliers of Scaffolding and Steel Productswww.kwikup.com.au
KwikstageProducts
K-Stage Standard
Standards are vertical structural member of thescaff old system which are made from 48.3 OD X 4mm TubesStandards have “V” pressings in clusters at 495mm centres, which provide location points forTransoms, Ledgers, Braces, Hopups etc and a spigotfi xed at thetop.
K-Stage Ledgers
Ledgers is horizontal member of the scaff old systemalso known as guard rails are made from 48.3 ODX 3.2 mm & 4 mm tubes. Ledgers fi t into the upper “V” Pressings on the standards.
K-Stage Transom
Transoms are made by welding two 5.00 mm anglesback to back. Transoms fi t into the lower “V”pressings on the standards to carry steel boards.2.4 m
Truss TransomUsed for heavy duty load spans and extended distances.
SpigotUsed to join 2 standards together. Requires either a hinged pin orspecial bolt.
Mass17.5kg14.5kg11.5kg
8.5kg6.0kg2.0kg
Mass9.2kg7.0kg5.0kg4.3kg
Mass22.0kg13.5kg
9.6kg8.0kg6.0kg
Length3.0m2.5m2.0m1.5m1.0m0.5m
Length2.4m1.8m1.2m0.7m
Length1.8m1.2m1.0m0.7m
K
K
Trb
2
KWIKUP PRODUCT BROCHURE 2014
K-Stage Steel Plank
Th e steel plank spans between the transoms giving anon slip surface with a is hot dip galvanized fi nish.
LVL Scaffold PlankIndividually proof tested and compliant in accordance with AS 1577 for Stiff ness, Strength, Sliding & SlipAvailable in various lengths & can be cross cut to exactlengthsStamped as Scaff old plank with AS compliance markHigh strengthChamfered edgesSuitable for PETROCHEMICAL & GAS industriesMeets industry standardsEnhanced durability & safety (AS)Competitively priced
K-Stage Hop Ups
Board Stage Brackets / hopups fi t into the “V” pressing of the standard which is nearest to the wall. Th e 2 & 3 BSB have holes into which tie bar pins are attached.Th ey are used to provide cantilevered platform on the inside of the scaff old nearest the wall.
Diagonal Braces
Th e diagonal brace is used to the full height of the scaf-folding in a longitudinal direction.
Mass15.0kg10.5kg
6.5kg4.0kg
Length2.4m1.8m1.2m0.7m
Mass17.5kg14.5kg11.5kg
8.5kg6.0kg2.0kg
Mass2.5kg6.0kg9.0kg
Mass13.5kg12.5kg11.0kg
9.5kg8.5kg7.5kg
Length3.0m2.5m2.0m1.5m1.0m0.5m
Bracket Type
1Board2Board3Board
Length3.6m3.2m2.7m2.4m2.0m1.7m
3
K-Stage Tie Bars
Tie bars have pins at each ends which fi t in holes of 2 and 3 board stage brackets (hopups) to prevent the brackets from spreading and the planks from becoming dislodged.
End Toe Board Brackets
Fits into ‘V’ locating lugs on the standard at the end of a platform to hold the endbatten toe board vertically in place.
Toe Board Bracket
Clamps to the standard with a captive wedge to hold the batten toe boardvertically in place.
Double C Clip / Gantry Coupler
Used to Join Standards Back to Back
Ladder Access TransomAn adjustable transom with landing for ladder/stairs
Mass7.0kg5.0kg3.0kg2.1kg
Length2.4m1.8m1.2m0.7m
Mass1.5kg
Mass0.8kg
b
b
4
KWIKUP PRODUCT BROCHURE 2014
Guardrail Post
Used for edge protection – slab or balcony’s. Bolted into concrete with 14mm Dyna Bolts. Compatible with all sizes of ledgers which makes it very versatile.
Step Down Bracket
Th e fi rst step onto a stair access or ladder access is always diffi cult due to siteconstraints, ground levels and base outs. Th e use of the adjustable step down bracket gives the comfort of adjustment to balance the variables so the stepbecomes balanced when getting on or getting off a stair access at ground
level
Wall Tie Bracket
SizeSuitable for 48mm tube, used to secure the scaff old to a structure
Base Plate
Add more stability to your scaff old structures with a base plate. When securedthe base plate stops tube from slipping across the fl oor.
Internal Corner PanelUsed with Hop Up Brackets to fi ll any corner gaps in the scaff old structure.
Mass2.20Kg
Size225x225mmB
IU
5
Scaffold Tubes
Tubes have a 48.3mm outside diameter andthe wall thickness of 4.05 the tubes are to be used with all types of couplers and fi ttings
Putlog Single Coupler
Used for joining putlogs or transoms to ledger tubes, providing a level unconstructed surface for planks and boards. Also used for securing ledgers to standards.
Half CouplerForged Steel piece, fi t for 48.3MM tube, which is fl at and un-plated, suitable for welding
Double CouplerA strong drop forged connector, providing strength under loadbearing situations joining tubes at 90 degree angles.
Blade Putlogplug adapter/pressed clamp, Converts 48.3mm scaff old tube into putlog for insertion into brickwork joints.
Couplers Tubes and Fittings
Length0.6m, 0.9m, 1.2m,1.5m, 1.8m, 2.1m,2.4m, 2.7m, 3.0m,3.3m, 3.6m, 3.9m,4.2m, 4.5m, 4.8m,5.1m, 5.4m, 5.7m,6.0m, 6.3m, 6.5m
Mass: 1.0 kg
Mass: 1.25 kg
6
KWIKUP PRODUCT BROCHURE 2014
Double Putlog Coupler
Makes connection of putlogs and transoms to standard scaff old tube whileallowing scaff old boards to be laid on top of the tube.
Beam ClampSolid one piece drop forged steel fi tting providing quick and secure fi xing toSbeamsbAlways to be used in pairsA
Swivel Beam Clamp
Drop forged with swivel capability used in pairs for variable angle clampingDof 48.3mm O.D. scaff old tubes to steel beam fl anges up to 45mm thicko
Hook Putlog
Th e Hook and base plate is made up of mild steel. Alternative to RAC
Mass: 1.5 kg
Mass: 1.6 kg
7
Internal Joiner
Internal expanding type fi tting to connection scaff old tube vertically end to end
Swivel Coupler
Connections to standard scaff old tube at any angle required.
External Joiner / Sleeve Coupler
External compression type fi tting to connection scaff old tube end to end
Hoarding ClipForged Steel piece, scaff old stop-ends and scaff old guard board returns are neatly and effi ciently locked into the correct positions to secure scaff olding
Hook CouplerUsed to attach ladders to scaff old
Mass: 1.3 kg
Mass: 1.3 kg
8
KWIKUP PRODUCT BROCHURE 2014
Adjustable Formwork Prop
The adjustable prop Provide emporary support and is easy to et up.
Prop Nut
Used to lock prop height
U Head Jacks
A high capacity sostem with a fi xed head
Shoring Jacks
A high capacity solid jack stem with a fi xed 8 inch Uhead
Mass3.86 kg7.75 kg1.50 kg4.42 kg0.24 kg
LengthProp No.0) 1.2 M-1.8 MProp No.1) 1.7 M–2.5 MProp No.2) 2.0 M–3.0 MProp No.3) 2.6 M–3.8 MProp No.4) 3.2 M–5.0 M
AF
Th tese
M11223
Le(P(P(P(P(P
Props and Formwork
cks
olid jack 8 inchh U
cks
9
Aluminium Hand RailAluminium Hand Railsprovide stability andsupport when climbingstairs units
Aluminium Top Hand RailProvide stability andsupport when climbingstairs units
Mesh Steel Palletis a steel transportstructure with a cage
that holds goods in a stable fashion whilebeing lift ed by a forklift
Ladder Beamsde a clear heavy n between extended6.3 m
Swivel JackProvides stability for uneven surface. 180 degree rotation for extra fl exibility. Constructed of heavy duty steel.Galvanised for long lasting protection.
Solid Base JackAdjustable base jack enables accurateleveling of the scaff olding on unevenground and infi nite adjustment onsloping groundSize: 36ODx710mmMass: 7.5 kg
Aluminium Stairs Unit
Aluminium Stair Units are theperfect product to incorporate within your Kwikstage scaff old system. Th ese 1.5m high stairrises are lightweight with non-slip treads and platform. Hand-rails and Exit Rails are also avail-able and comply with Australian
Standards
Steel Pallet
is a steel transport structure that supports goods in a sta-ble fashion while being lift edby a forklift
AccesoriesList
LB
To providduty spandistances6
MPis
10
KWIKUP PRODUCT BROCHURE 2014
Branch & Distribution NetworkBranch & Distribution Network
When you need scaff olding anywhere, anytime, think KwikUP.Find Us Online or Just CallFind us on the web at www.kwikup.com.au or call us at (02) 97292122 to talk to someone now. Our staff is Friendly and eager tohelp fi nd what you are looking for.
Warehouse InformationKwikUP Head Offi ce: 02 9729 2122FAX: 02 97292473
Sydney Warehouse28 – 54 Percival roadSmithfi eld NSW – 2164
Perth WarehouseUnit C, 33 McDowell St.Welshpool WA 6106
Postal Address
Post – P.O.Box 2166Smithfi eld NSW 2164
11
Contact Details
KwikUP Head Offi ce: 02 9729 2122FAX: 02 97292473
Sydney Warehouse28 – 54 Percival road
Smithfi eld NSW – 2164
Perth WarehouseUnit C, 33 McDowell St.
Welshpool WA 6106
Postal AddressPost – P.O.Box 2166
Smithfi eld NSW 2164
www.kwikup.com.au