KUST Elektronik Intelligent Test Solutions
Transcript of KUST Elektronik Intelligent Test Solutions
Test and measurement Solutions from KUST offer a complete and versatile answer for all the challenges in todays technology.KUST is proud to offer unique and affordable test and measurement products which allow to perform complete and uncompromising testing. Products are provided in ready to use out of box and guarantee easy and stress free testing.
SUPPORT:Technical pre and post sale support for all the products and applications. Unique products backed-up by extensive applica-tion knowledge. Service centre within your country: calibration & repair.
DESIGN:All Products designed aroundcustomer needs and requirements , Application knowledge, field experience and test challenges taken in to consideration when test solution is created.
SALES NETWORK:Fully trained and authorised sales network across the Europe and Middle East - Helping hand is never far away. Materials and informations available in native languages (contentiously updated)
DEVELOPMENT:Good technical understanding of todays testing requirements allows KUST to contentiously implement new functions and introduce new products. Special customer requirements always considered.
www.kust.de | www.kust-elektronik.com
KUST ElektronikIntelligent Test Solutions
L C R M E T E R S H I G H V O L T A G E T E S T E R S I M P U L S E / S U R G E C O M P O N E N T S T E S T E R S M I L L I O H M M E T E R S
LCR METERS/COMPONENT TESTERS: KUST Elektronik:
2 KUST Elektronik
www.kust.de | www.kust-elektronik.com
KUST LM1020
KUST LM1040 KUST LM1030
KUST LM1050
KUST LM1010
LCR Meters, from low to high bandwidth, with component analysis function. Combination of world leading technology and decades of experience allowing KUST
to offer very advanced products to suit any application and customer needs. We have LCR meter to suit any need and application.
Advanced Inductance and impedance measurement technology.
Model LM1010 LM1020 LM1030 LM1040 LM1050Bandwidth: up to 200kHz up to 200kHz up to 500kHz 1MHz up to 5MHzTest Signal: 1V AC 2V AC 2V AC 2V AC 5V ACBasic error: 0.05% 0.05% 0.05% 0.05% 0.05%
LM1010A is a new precision LCR combined with years of technical experience and new measurement technology. With powerful mea-surement functions, high performance and low cost, LM1010 have been one of the world most advanced instruments at very low cost. The meter offers stable 5 digit resolution, wide frequency range, up to 40 meas/sec measurement rate, 9 measurement ranges, 30Ω or 100Ω constant output impedance and friendly operation interface. LM1010 can be used for incoming inspection of components, quality control on product line or high accura-cy laboratory use.The HANDLER, GPIB, RS232C interfaces make it easy to build an automatic test sys-tem. USB interface allows quick data saving for further analysis
LCR METER:LM1010
3 KUST Elektronik
www.kust.de | www.kust-elektronik.com
Features:LM1010A: 100kHz: 10 frequency points LM1010B: 200kHz: 37 frequency points • AC Signal: 0.1V, 0.3V, 1V AC• up to 40 measurment/sec.• 4.3” LCD Display • Test Signal Level Monitor• 30Ω or 100Ω output Impedance• Parameters: L,C, R, |Z|,|Y|, X, B, G, D, θ, Q• Basic Accuracy: 0.1%• Comms: RS232, HANDLER,USB host, GPIB(optional)• LED Indication of the result Green - PASS / Red - FAIL• Beeper - result sound indication• Trigger Function: Manual, Internal, External, BUS• Internal Memory for 100 Instrument Settings/500 settings external • Key-Lock with password function• Correction/Compensation Function• List Sweep Function: up to 4 parametrs: test signal or DC BIAS• Large or Normal Character for result display
LCR METER: LM1010
4 KUST Elektronik
www.kust.de | www.kust-elektronik.com
Measurement functionLCR test parameters | Z |, | Y |, C, L, X, B, R, G, D, Q, θ
Test frequency:
LM1010A 50Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz, total of 10
LM1010B 50,60,80,100,120,150,200,250,300,400,500,600,800,1K, 1.2K, 1.5K, 2K, 2.5K, 3K, 4K, 5K, 6K, 8K,
10K, 12K, 15K, 20K, 25K, 30K, 40K, 50K, 60K, 80K, 100K, 120K, 150K, 200K (Hz), total of 37
Basic accuracy LM1010A: 0.05%
LM1010B: 0.1%
The equivalent circuit Series, parallel
Mathematical functions The absolute value of the deviation, percentage deviation
Range mode Automatic, hold, manually select
Trigger Internal, manual, external, bus
Measurement speed (≥1kHz) Fast: The fastest 40 times / sec speed: 11 times / sec, Slow: 3 times / sec.
The average number of 1-255
Delay time 0-60s, with 1ms step
Calibration function Open / short / load
Test side configuration Five end
Display mode Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)
Monitor 5 resolution, 4.3-inch LCD Monitor
Test signalTest signal frequency LM1010A: 50 Hz - 100 kHz
LM1010B: 50Hz – 200kHz
Output Impedance 30 Ω, 100Ω selectable
Test signal level Normal: 0.1V, 0.3V, 1V Accuracy: 10%
Bias source Internal ± 2V bias source, accuracy: 1%
External Scalable ± 5VDC bias source
Display range| Z |, R, X 0.01mΩ - 99.999 MΩ
| Y |, G, B 0.0001μS - 99.999 S
C 0.0001 pF - 9.9999 F
L 0.0001 μH - 999.99 H
D 0.0001 - 9.9999
Q 0.0001 --99999
θ (DEG) -179.99º - 179.99 º
θ (RAD) -3.14159 - 3.14159
OtherComparator function sorting function
Memory 100 internal instrument settings for storage / recall, external 500 groups
Interface Standard RS232C, HANDLER, USB HOST, optional GPIB
ORDERING INFO:
LM1010A LCR METERLM1010B LCR METER STANDARD COMMUNICATION PORTS:RS232, HANDLER/PLC, USB IN THE BOX:KA1001 4 terminal test fixtureKA1002 4 terminal Kelvin test clip leadsKA1008 Shorting plate Mains Lead Test Cerifiacte OPTIONS:KA1005 SMD test fixture - pin/leg typeKA1006 SMD test fixture -pad typeKA1007 SMD test tweezersKA1025 GPIB interfaceKA1026 RS232 Software
Features:LM1020A: 100kHz: 16 frequency points LM1020B: 200kHz: 1500 frequency points • AC Signal: 0.05V to 2V, 1mV resolution Constant Voltage: 10mV - 1V, 1mV resolution• DC BIAS Internal Voltage: 0V, 1.5V, 2V• Optional ±10V (±100mA) & 1A Internal BIAS source (LM1020B Only)• Basic Accuracy: 0.05%• 5” LCD Display• Parameters: |Z|,|Y|,L,C,R,G,D,Q,Rs,Rp,X,B,θ,DCR• ALC - Automatic level control• Voltage and Currrent Monitor• Frequency response Analysis• Sweep Function: 10 points: test signal, DC BIAS• Correction/Compensation Function• RS232, HANDLER,USB host, GPIB(optional), Ethernet(optional)• Beeper - result sound indication• LED Indication of the result Green - PASS / Red - FAIL• Password protection• Display PASS/FAIL and beeper indication for the result• Up to 75 measurement/sec.• Trigger: Internal, manual, BUS• Internal Memory for 100 Instrument Settings / 500 External memory• USB for direct result saving
LCR METER:LM1020
5 KUST Elektronik
www.kust.de | www.kust-elektronik.com
Brief Introduction:The LM1020 is an auto component analyzer with high accuracy, wide measurement range and six digit reso-lution. LM1020 can be used for incoming inspection of components, quality control and laboratory use over a wide range of frequency(up to 200kHz) and test signal level (5 mV to 2V). The HANDLER, GPIB, RS232C interfaces make it easy to build an automatic component test system, communicate with the computer and record the test results “PRECISION LCR METER WITH GREAT CAPABILITY FOR COMPONENT TESTING”
The instrument can identify the slight change of the component parameter with its 6 digit resolution
6 KUST Elektronik
www.kust.de | www.kust-elektronik.com
LCR METER:LM1020Measurement function
Test parameters | Z |, | Y |, C, L, X, B, R, G, D, Q, θ, DCR (customization)
Test frequency LM1020A: 50 Hz-100 kHz, 16 frequency points LM1020B: 50 Hz-200 kHz, 1500 frequency points
Basic accuracy: 0.05%
The equivalent circuit Series, parallel
Mathematical functions The absolute value of the deviation, percentage deviation
Range mode Automatic, hold, manually select
Trigger Internal, manual, external, bus
Measurement speed (≥1kHz) Fast: 75 times / sec speed: 12 times / sec, Slow: 3 times / sec.
The average number of 1-255
Delay time 0-60s, with 1ms step
Calibration function Open / short / load
Test side configuration Five end
List sweep LM1020BA for 10 points list sweep function, the other for 4:00
Display mode Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)
Monitor 6 resolution, 5 inches LCD display
Test signalTest signal frequency 50 Hz-200 kHz (LM1020A up to 100kHz)
Output Impedance 30 Ω, 100Ω, 10 / 100,10 / CC optional
Test signal level Normal: 5 mV-2 V Accuracy: 10%, 1 mV step constant level: 10 mV-1 V Accuracy: 5%, 1 mV step
DC bias source
Internal 0V, 1.5V, 2V, accuracy: 1%
Optional 0-10V DC bias voltage of, 0-100mA DC bias current (LM1020B only)
0-1A DC bias current (LM1020B only)
Display range| Z |, R, X 0.01mΩ - 99.9999 MΩ
DCR 0.001 mΩ - 99.9999 MΩ
| Y |, G, B 0.00001μS - 99.9999 S
C 0.00001 pF - 9.9999 F
L 0.00001 μH - 9999.99 H
D 0.00001 - 9.9999
Q 0.00001 - 9999.9
θ (DEG) -179.999º - 179.999 º
θ (RAD) -3.14159 - 3.14159
OtherComparator function Nine in ten stages qualified file, a file failed), a subsidiary of another file AUX
Memory 100 internal instrument settings for storage / recall, external 500 groups
Interface Standard RS232C, HANDLER, USB HOST, headphone jack, optional GPIB, LAN interface
ORDERING INFO:
LM1020A LCR METERLM1020B LCR METER STANDARD COMMUNICATION PORTS:RS232, HANDLER/PLC, USB IN THE BOX:KA1004 4 terminal test fixtureKA1010 4 terminal Kelvin clip leadsKA1008 Shorting plate Mains Lead Test Cerifiacte OPTIONS:KA1005 SMD test fixture - pin/leg typeKA1006 SMD test fixture -pad typeKA1007 SMD test tweezersKA1025 GPIB interfaceKA1026 RS232/USB Software
Features:LM1030A: 20Hz - 200kHz, 10mHz resolutionLM1030B: 20Hz - 300kHz, 10mHz resolutionLM1030C: 20Hz - 500kHz, 10mHz resolution • AC Signal: 5mV - 2V, 1mV resolution constant source: 10mV - 1V, 1mV resolution• DC BIAS: Internal: 0V, 1.5V, 2V Optional: ±10V (±100mA) DC Bias Current 0-1A DC Bias Current• Basic Accuracy: 0.05%• Parameters: |Z|,|Y|,L,C,R,G,D,Q,Rs,Rp,X,B,θ,DCR• ALC - Automatic level control• Frequency response Analysis• 800 × 480 RGB 7 inch 16: 9 TFT LCD Monitor• Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)• 4 parameter dispaly in any configuartion• Sweep Function: up to 10 points: test signal, DC BIAS• Graphical results: trace sweep Function, frequency response• Correction/Compensation Function• RS232C, HANDLER, GPIB(optional), LAN (optional• USB DEVICE (USBTMC and USBCDC support)• USB HOST (FAT16 and FAT32 support)• Beeper - result sound indication• LED Indication of the result Green - PASS / Red - FAIL• Key-Lock, Password protection• Output Impedance: 10/CC(Constant Current), 30Ω,50Ω,100Ω• Up to 75 Measurement/sec• Trigger Function: Manual, Internal, External, BUS• Internal Memory for 10 Instrument Settings• Direct result, screenshots and settings saving to USB poratbale memory
LCR METER:LM1030
7 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
‘Perfect tool for the high speed production testing or
R&D Designers working on high frequency magnetics‘
LM1030 series is a new generation complex impedance test instru-ment. It fulfills most low-voltage parameter measurement needs for components and materials with its basic accuracy (0.05%), wide frequency range(from 20Hz to 500kHz). The instrument is widely applied in microphone, resonator, inductor, ceramic capacitor, LCD, varactor and transformer .etc to analyze electrical performance. Perfect for testing low-ESR capacitors or very high-Q inductors. With the high test speed, LM1030 series is often used for frequen-cy response analyzing. Test of piezoelectric devices or auto pro-duction line. Its multiple output impedance mode can be used for different type of inductors or variety of transformer. With its prominent performance, LM1030 series is in conformity with commercial and military standards.
LCR METER:LM1030
8 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
Measurement functionTest frequency LM1030A 20Hz - 200KHz, 10mHz Resolution
LM1030B 20Hz - 300KHz, 10mHz Resolution
LM1030C 20Hz - 500KHz, 10mHz Resolution
Test parameters | Z |, | Y |, C, L, X, B, R, G, D, Q, θ, DCR
Basic accuracy 0.05%
The equivalent circuit Series, parallel
Mathematical functions The absolute value of the deviation, percentage deviation
Range mode Automatic, hold, manually select
Trigger Internal, manual, external, bus
Measurement speed (≥1kHz) Fast: 75 times / sec speed: 12 times / sec, Slow: 3 times / sec.
The average number of 1-255
Delay time 0-60s, with 1ms step
Calibration function Open / short / load
Test side configuration Five end
List sweep 10:00 list sweep function
Display mode Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)
Monitor 800 × 480 RGB 7 inch 16: 9 TFT LCD MonitorTest signal
Output Impedance 30 Ω, 100 Ω, 10/100, 10 / CC optional
Test signal level Normal: 5mV-2V Accuracy: 10%, 1 mV step
constant level: 10 mV-1 V Accuracy: 5%, 1 mV step
DC bias
source
Internal 0V, 1.5V, 2V, accuracy: 1%
Optional ± 10V (± 100mA) DC bias current
0-1A DC bias current
Display range
| Z |, R, X 0.01mΩ - 99.9999 MΩ
DCR 0.01 mΩ - 99.9999 MΩ
| Y |, G, B 0.00001μS - 99.9999S
C 0.00001pF - 9.9999F
L 0.00001μH - 9999.99H
D 0.00001 - 9.9999
Q 0.00001 - 9999.9
θ (DEG) -179.999º - 179.999º
θ (RAD) -3.14159 - 3.14159
Other
Comparator function Nine in ten stages qualified file, a file failed), and another AUX file
Memory 10 internal instrument settings for storage / recall
Interface Standard RS232C, HANDLER, USB HOST, headphone jack, optional GPIB, LAN interface
ORDERING INFO:
LM1030A LCR METERLM1030B LCR METERLM1030C LCR METER
STANDARD COMMUNICATION PORTS:RS232, HANDLER/PLC, USB IN THE BOX:KA1004 4 terminal test fixtureKA1010 4 terminal Kelvin clip leadsKA1008 Shorting plate Mains Lead Test Cerifiacte OPTIONS:KA1005 SMD test fixture - pin/leg typeKA1006 SMD test fixture -pad typeKA1007 SMD test tweezersKA1025 GPIB interfaceKA1026 RS232/USB Software
Features:LM1040: 20Hz - 1MHz, 10mHz resolution • AC Signal: 5mV - 2V, 1mV resolution constant source: 10mV - 1V, 1mV resolution• DC BIAS: Internal: 0V, 1.5V, 2V Optional: ±10V (±100mA) DC Bias Current 0-1A DC Bias Current• Basic Accuracy: 0.05%• Parameters: |Z|,|Y|,L,C,R,G,D,Q,Rs,Rp,X,B,θ,DCR• ALC - Automatic level control• Frequency response Analysis• 800 × 480 RGB 7 inch 16: 9 TFT LCD Monitor• Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)• 4 parameter dispaly in any configuartion• Sweep Function: up to 10 points: test signal, DC BIAS• Graphical results: trace sweep Function, frequency response• Correction/Compensation Function• RS232C, HANDLER, GPIB(optional)• USB DEVICE (USBTMC and USBCDC support)• USB HOST (FAT16 and FAT32 support)• LAN optional• Beeper - result sound indication• LED Indication of the result Green - PASS / Red - FAIL• Key-Lock, Password protection• Output Impedance: 10/CC(Constant Current), 30Ω,50Ω,100Ω• Up to 50 Measurement/sec• Trigger Function: Manual, Internal, External, BUS• Internal Memory for 10 Instrument Settings• Direct result, screenshots and settings saving to USB poratbale memory
LCR METER:LM1040
9 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
Introduction:LM1040 series is a new precision LCR meter with various functions and a higher test frequency. With small size and portable appearance, it is convenient for use in the test racks. This instru-ment has a basic accuracy of 0.05%, maximum test frequency of 1MHz and resolution of 10 mHz. It is easy to operate with a 4.3-inch LCD screen as well as selectable Chinese and English operation interfaces. Integrated transformer test function and balance test function greatly improve the test efficiency. The instrument is also provided with multiple interfaces which can meet various requirements of the automatic sorting test, data transmission and storage. Voltage monitor makes this a perfect tool for DC BIAS testing as it can monitor and compensate perfectly for the Voltages and Current present across the part under test. Easy to use, light and very rugged makes LM1040 perfect for any environment.
10 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
LCR METER:LM1040Measurement function
Test frequency LM1040 20Hz - 1MHz, 10mHz Resolution
Test parameters | Z |, | Y |, C, L, X, B, R, G, D, Q, θ, DCR
Basic accuracy 0.05%
The equivalent circuit Series, parallel
Mathematical functions The absolute value of the deviation, percentage deviation
Range mode Automatic, hold, manually select
Trigger Internal, manual, external, bus
Measurement speed ≥1kHz Fast: 50 times / sec speed: 12 times / sec, Slow: 3 times / sec
The average number of 1-255
Delay time 0-60s, with 1ms step
Calibration function Open / short / load
Test side configuration Five end
List sweep 10:00 list sweep function
Display mode Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)
Monitor 800 × 480 RGB7 inch 16: 9 TFT LCD Monitor
Test signal
Output Impedance 30 Ω, 100 Ω, 50Ω, 10 / CC optional
Test signal level Normal: 5mV-2V, 1mV stepping constant level: 10mV-1V, 1mV step
Bias source Internal 0V, 1.5V, 2V
Optional 0-1A DC bias current
± 10V (± 100mA) DC bias current
0 - 1A DC BIAS Current
Display range
| Z |, R, X 0.01mΩ -99.9999 MΩ
DCR 0.01 mΩ -99.9999 MΩ
| Y |, G, B 0.00001μS -99.9999 S
C 0.00001 pF -9.9999 F
L 0.00001 μH -9999.99 H
D 0.00001 -9.9999
Q 0.00001 -9999.9
θ (DEG) -179.999º -179.999 º
θ (RAD) -3.14159 -3.14159
Other
Comparator function Nine in ten stages qualified file, a file failed), while a subsidiary AUX file
Memory 10 internal instrument settings for storage / recall
Interface Standard RS232C, HANDLER, USB HOST, headphone jack, optional GPIB, LAN interface
ORDERING INFO:
LM1040 LCR METER
STANDARD COMMUNICATION PORTS:RS232, HANDLER/PLC, USB IN THE BOX:KA1004 4 terminal test fixtureKA1010 4 terminal Kelvin clip leadsKA1008 Shorting plate Mains Lead Test Cerifiacte OPTIONS:KA1005 SMD test fixture - pin/leg typeKA1006 SMD test fixture -pad typeKA1007 SMD test tweezersKA1025 GPIB interfaceKA1026 RS232/USB Software
Features:LM1050A: 20Hz - 2MHz, selectable Frequency, 10mHz resolutionLM1050B: 20Hz - 5MHz, selectable Frequency, 10mHz resolution • AC Signal: f≤1MHz 10mV ~ 5V f> 1MHz 10mV ~ 1V• DC BIAS: Internal: -5V ~ +5V DC BIAS Voltage Source Optional: ±10V (±100mA) DC Bias Current 0-1A DC Bias Current• Basic Accuracy: 0.05%• Parameters: |Z|,|Y|,L,C,R,G,D,Q,Rs,Rp,X,B,θ,DCR• ALC - Automatic level control• Frequency response Analysis• 800 × 480 RGB 7 inch 16: 9 TFT LCD Monitor• Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)• 4 parameter dispaly in any configuartion• Sweep Function: up to 10 points: test signal, DC BIAS• Graphical results: trace sweep Function, frequency response• Correction/Compensation Function• RS232C, HANDLER, GPIB(optional)• USB DEVICE (USBTMC and USBCDC support)• USB HOST (FAT16 and FAT32 support)• LAN optional• Beeper - result sound indication• LED Indication of the result Green - PASS / Red - FAIL• Key-Lock, Password protection• Output Impedance: 10/CC(Constant Current), 30Ω,50Ω,100Ω• Up to 75 Measurement/sec• Trigger Function: Manual, Internal, External, BUS• Internal Memory for 10 Instrument Settings• Direct result, screenshots and settings saving to USB poratbale memory
LCR METER:LM1050
11 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
LM1050 series is a new generation impedance test instrument with the most advanced technique of auto balancing bridge in the world.LM1050 Answer all the measurement needs for components and materials with its high basic accuracy (0.05%),wide frequency range (from 20 Hz to 5MHz) and impedance range (up to 100MΩ). The instrument is especially suitable for low dissipation factor(D)capacitor and high quality factor (Q) inductor measurements List sweep function make it easy to extend user’s capability of component evalu-ation. Four-terminal pair terminal configuration which eliminates the electromagnetic coupling of test leads,extends the low impedance measurement range ten times down of the normal five-terminal configuration instrument. LM1050 series is a powerful analyser for component design,component inspec-tion,quality control and measurement on production lines. LM1050 is also a powerful tool for design and research of circuit and materials(electronic material and non- electronic material). Excellent performance of the LM1050 allows conformity to commercial and military standards,for example IEC and MIL.
Very Easy to use, very powerful “all what you need” Instrument for variety of electrical and nonelectrical components.
LCR METER:LM1050
12 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
Measurement function
Test frequency LM1050A 20 Hz-2MHz, 10mHz Resolution
LM1050B 20 Hz-5MHz, 10mHz Resolution
Test parameters | Z |, | Y |, C, L, X, B, R, G, D, Q, θ, DCR
Basic accuracy: 0.05%
The equivalent circuit Series, parallel
Mathematical functions The absolute value of the deviation, percentage deviation
Range mode Automatic, hold, manually select
Trigger Internal, manual, external, bus
Measurement speed (≥1kHz) Fast: 200 times / sec, Medium: 12 times / sec, Slow: 3 times / sec
The average number of 1-255
Delay time 0-60s, with 1ms step
Calibration function Open / short / load
Test side configuration Five end
List sweep 10:00 list sweep function
Display mode Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)
Monitor 800 × 480 RGB7 inch 16: 9 TFT LCD Monitor
Test signalOutput Impedance 30 Ω, 100 Ω, 50Ω, 10 / CC optional
Test signal level f≤1MHz 10mV ~ 5V, ± (10% + 10mV) f>1MHz 10mV ~ 1V, ± (20% + 10mV)
Bias source Internal -5V ~ + 5V DC bias voltage source, Accuracy: 1%
Optional ± 10V (± 100mA) DC bias current
0-1A DC bias current
Display range
| Z |, R, X 0.01mΩ -99.9999 MΩ
DCR 0.01 mΩ -99.9999 MΩ
| Y |, G, B 0.00001μS -99.9999 S
C 0.00001 pF -9.9999 F
L 0.00001 μH -9999.99 H
D 0.00001 -9.9999
Q 0.00001 -9999.9
θ (DEG) -179.999º -179.999 º
θ (RAD) -3.14159 -3.14159
Other
Comparator function Nine in ten stages qualified file, a file failed), while a subsidiary AUX file
Memory 10 internal instrument settings for storage / recall
Interface Standard RS232C, HANDLER, USB HOST, headphone jack, optional GPIB, LAN interface
ORDERING INFO:
LM1050A LCR METER LM1050B LCR METER
STANDARD COMMUNICATION PORTS:RS232, HANDLER/PLC, USB IN THE BOX:KA1004 4 terminal test fixtureKA1010 4 terminal Kelvin clip leadsKA1008 Shorting plate Mains Lead Test Cerifiacte OPTIONS:KA1005 SMD test fixture - pin/leg typeKA1006 SMD test fixture -pad typeKA1007 SMD test tweezersKA1025 GPIB interfaceKA1026 RS232/USB Software
“ Most modern, most advanced and most power-ful LCR Meter...........”
13 KUST Elektronik
www.kust .de | www.kust-e lektronik .com
NOTES: