KP Buick Sample
2
BUICK Model: Year: LaCrosse 2010-13 Regal 2011-12 Remote alarm/central locking System operation l Pressing remote transmitter UNLOCK button deactivates alarm system (if fitted) and unlocks driver's door only. l Pressing remote transmitter UNLOCK button twice within 5 seconds deactivates alarm system (if fitted) and unlocks all doors. l Pressing remote transmitter LOCK button once locks all doors and activates the alarm (if fitted). l Pressing remote transmitter trunk release button for 1 second activates trunk release. l Pressing remote transmitter panic button once activates the following functions: q Sounds horn 3 times. q Flashes hazard lamps 3 times. l Pressing remote transmitter panic button for 2 seconds activates the following functions for 30 seconds: q Sounds horn intermittently. q Flashes hazard lamps. l Pressing remote transmitter panic button again, or switching ignition ON deactivates the alarm. l Alarm/central locking functions can be altered using Driver information center (DIC). Programming When l System malfunction. l Remote transmitter added or replaced. How - without Smart entry system l Remote transmitter can only be programmed using diagnostic equipment. NOTE: Existing remote transmitter programming will be erased. l Obtain and reprogram all remote transmitters. NOTE: A maximum of 5 remote transmitters can be programmed. How - with Smart entry system and one programmed remote transmitter available NOTE: A maximum of 5 remote transmitters can be programmed. l Obtain all remote transmitters. NOTE: Switch ignition OFF. l Place all programmed remote transmitters in the cupholder. l Insert key of the unrecognized remote transmitter into the driver's door lock. l Turn key to unlock position 5 times within 10 seconds. q Driver information center will display READY FOR REMOTE # 2, 3, 4 or 5. l Place the unrecognized remote transmitter into the remote transmitter pocket Fig. 127839 with buttons facing up. l Press the ignition switch. l When remote transmitter is programmed, the DIC will show it is ready for next remote transmitter. l Remove remote transmitter from remote transmitter pocket and press the UNLOCK button. l To program additional remote transmitters, repeat previous steps starting with inserting next remote transmitter key into the driver's door lock. NOTE: To exit the programming mode, press and hold the ignition button for 10 seconds. How - with Smart entry system and no programmed remote transmitter available NOTE: A maximum of 5 remote transmitters can be programmed. l Obtain all remote transmitters. NOTE: Switch ignition OFF. l Insert key of the unrecognized remote transmitter into the driver's door lock. l Turn key to unlock position 5 times within 10 seconds. q Driver information center will display REMOTE LEARN PENDING, PLEASE WAIT. l Wait 10 minutes until DIC displays PRESS ENGINE START BUTTON TO LEARN. l Press ignition switch. q Driver information center will display REMOTE LEARN PENDING, PLEASE WAIT. Key Operation and Programming Key Operation and Programming x 1
-
Upload
abbode-horani -
Category
Documents
-
view
4 -
download
0
description
KP Buick Sample
Transcript of KP Buick Sample
SPINE
BUICK
Model: Year:
LaCrosse 2010-13
Regal 2011-12
Remote alarm/central locking
System operationl Pressing remote transmitter UNLOCK button
deactivates alarm system (if fitted) and unlocks driver'sdoor only.
l Pressing remote transmitter UNLOCK button twicewithin 5 seconds deactivates alarm system (if fitted) andunlocks all doors.
l Pressing remote transmitter LOCK button once locks alldoors and activates the alarm (if fitted).
l Pressing remote transmitter trunk release button for1 second activates trunk release.
l Pressing remote transmitter panic button once activatesthe following functions:q Sounds horn 3 times.q Flashes hazard lamps 3 times.
l Pressing remote transmitter panic button for 2 secondsactivates the following functions for 30 seconds:q Sounds horn intermittently.q Flashes hazard lamps.
l Pressing remote transmitter panic button again, orswitching ignition ON deactivates the alarm.
l Alarm/central locking functions can be altered usingDriver information center (DIC).
Programming
Whenl System malfunction.l Remote transmitter added or replaced.
How - without Smart entry systeml Remote transmitter can only be programmed using
diagnostic equipment.
NOTE: Existing remote transmitter programming will beerased.l Obtain and reprogram all remote transmitters.
NOTE: A maximum of 5 remote transmitters can beprogrammed.
How - with Smart entry system and oneprogrammed remote transmitter available
NOTE: A maximum of 5 remote transmitters can beprogrammed.
l Obtain all remote transmitters.
NOTE: Switch ignition OFF.
l Place all programmed remote transmitters in the cupholder.l Insert key of the unrecognized remote transmitter into
the driver's door lock.l Turn key to unlock position 5 times within 10 seconds.
q Driver information center will display READYFOR REMOTE # 2, 3, 4 or 5.
l Place the unrecognized remote transmitter into theremote transmitter pocket Fig. 127839 with buttonsfacing up.
l Press the ignition switch.l When remote transmitter is programmed, the DIC will
show it is ready for next remote transmitter.l Remove remote transmitter from remote transmitter
pocket and press the UNLOCK button.l To program additional remote transmitters, repeat
previous steps starting with inserting next remotetransmitter key into the driver's door lock.
NOTE: To exit the programming mode, press and hold theignition button for 10 seconds.
How - with Smart entry system and noprogrammed remote transmitter available
NOTE: A maximum of 5 remote transmitters can beprogrammed.
l Obtain all remote transmitters.
NOTE: Switch ignition OFF.l Insert key of the unrecognized remote transmitter into
the driver's door lock.l Turn key to unlock position 5 times within 10 seconds.
qDriver information center will display REMOTELEARN PENDING, PLEASE WAIT.
l Wait 10 minutes until DIC displays PRESS ENGINESTART BUTTON TO LEARN.
l Press ignition switch.qDriver information center will display REMOTE
LEARN PENDING, PLEASE WAIT.
File name:
Path:
Description:
Product no:
Imported from:
Section:
Date:
Operator:
Comments:
bui23imm_usa-xml - ver 1.0.0.0
g:/products/immob/xml
Immob_USA_xml_ML
12-420
N:/immob/usa/editorial/
Main Text
7/12/12 Time: 14:37
Tricia
1st proof
Autodata Limited Copyright 2012
Key Operation and Programming
Key Operation and Programming
x 1
SPINE
bui23imm_usa-xml - Key Programming USA (Template v1.1 -06/06/07)
l Wait 10 minutes until DIC displays PRESS ENGINESTART BUTTON TO LEARN.
l Press ignition switch.qDriver information center will display REMOTE
LEARN PENDING, PLEASE WAIT.l Wait 10 minutes until DIC displays PRESS ENGINE
START BUTTON TO LEARN.l Press ignition switch.
qDriver information center will display REMOTELEARN PENDING, PLEASE WAIT.
l All previously programmed remote transmitters are nowerased.q DIC will display READY FOR REMOTE #1.
l Place the unrecognized remote transmitter into theremote transmitter pocket Fig. 127839 with buttonsfacing up.
l Press the ignition switch.l When remote transmitter is programmed, the DIC will
show it is ready for next remote transmitter.l Remove remote transmitter from remote transmitter
pocket and press the UNLOCK button.l To program additional remote transmitters, repeat
previous steps starting with inserting next remotetransmitter into the remote transmitter pocket.
NOTE: To exit the programming mode, press and hold theignition button for 10 seconds.
127811
AD127811
127839
AD127839
Battery replacement
1142591
2
3
4
AD114259
Immobilizer
Without Smart entry system
System operationl Arms after removing ignition key.
ProgrammingWhenl Key added or replaced.l System malfunction.
How - without original master keyl Keys can only be programmed using diagnostic
equipment.
How - with original master keyl Insert master key into ignition.l Switch ignition ON.l Switch ignition OFF.l Remove master key.l Within 5 seconds insert new key and switch ignition ON.l New key now programmed.
NOTE: A maximum of 8 keys can be programmed
With Smart entry system
System operationl Arms after ignition button is turned to OFF.
ProgrammingWhenl Remote transmitter added or replaced.l System malfunction.
Howl Immobilizer is programmed during remote transmitter
programming procedure.
2 x
LaCrosse . RegalBUICK
Key Operation and Programming
File name:
Path:
Description:
Product no:
Imported from:
Section:
Date:
Operator:
Comments:
bui23imm_usa-xml - ver 1.0.0.0
g:/products/immob/xml
Immob_USA_xml_ML
12-420
N:/immob/usa/editorial/
Main Text
7/12/12 Time: 14:37
Tricia
1st proof
