Knock sensor for Toyota NZE engine
-
Upload
talleban-tal -
Category
Documents
-
view
49 -
download
5
description
Transcript of Knock sensor for Toyota NZE engine
![Page 1: Knock sensor for Toyota NZE engine](https://reader030.fdocuments.in/reader030/viewer/2022020105/55305c9d4a7959de2a8b46f2/html5/thumbnails/1.jpg)
A65758
Knock Sensor
ECM
KNK1E4
(Shielded)
2
BR
EC
AAJ3 J4
1W B
JunctionConnector
EKNKE42
W
1
–DIAGNOSTICS SFI SYSTEM (1ZZ–FE)05–73
273Author: Date:
2003 COROLLA MATRIX (RM940U)
DTC P0325 KNOCK SENSOR 1 CIRCUIT MALFUNCTION(BANK 1)
CIRCUIT DESCRIPTIONThe knock sensor is fitted to the cylinder block to detect the engine knocking. This sensor contains a piezo-electric element which generates a voltage when it becomes deformed. This occurs when the cylinder blockvibrates due to knocking. If the engine knocking occurs, the ignition timing is delayed to suppress it.
DTC No. DTC Detecting Condition Trouble Area
P0325No knock sensor signal to ECM with engine speed, 2,000 rpmor more
Open or short in knock sensor circuitKnock sensor (looseness)ECM
HINT:If the ECM detects above diagnosis conditions, it operates the fail safe function in which the corrective retardangle value is set to the maximum value.
WIRING DIAGRAM
INSPECTION PROCEDUREHINT:Read freed frame data using hand–held tester OBD II scan tool. Because freeze frame records the engineconditions when the malfunction is detected, when troubleshooting it is useful for determining whether thevehicle was running or stopped, the engine warmed up or not, the air–fuel ratio lean or rich, etc. at the timeof the malfunction.
057HW–02
![Page 2: Knock sensor for Toyota NZE engine](https://reader030.fdocuments.in/reader030/viewer/2022020105/55305c9d4a7959de2a8b46f2/html5/thumbnails/2.jpg)
A65745
EKNK KNK1
A05134
A65745
EKNK KNK1
05–74–DIAGNOSTICS SFI SYSTEM (1ZZ–FE)
274Author: Date:
2003 COROLLA MATRIX (RM940U)
1 CHECK HARNESS AND CONNECTOR
(a) Check for short on the wire harness between the ECMand the knock control sensor.(1) Disconnect the ECM E4 connector.(2) Check for short between the terminals KNK1 of
ECM connector and EKNK of ECM connector.Resistance: 1 M Ω or more
(b) Reference: Inspection using the oscilloscope.(1) With the engine racing at 4,000 rpm, check the wa-
veform between terminal KNK1 of the ECM connec-tor and the body ground.
HINT:The correct waveforms are as shown in the left.
(2) Spread the time on the horizontal axis, and confirmthat period of the wave is 80 µ seconds (Normalmode vibration frequency of knock sensor: 11.7kHz).
OK Go to step 3
NG
2 INSPECT KNOCK CONTROL SENSOR (See page 10–2)
NG REPLACE KNOCK CONTROL SENSOR
OK
3 CHECK HARNESS AND CONNECTOR(ECM–KNOCK CONTROL SENSOR)
(a) Disconnect the knock control sensor connector.(b) Disconnect the ECM E4 connector.(c) Check continuity between the terminals KNK1 of the ECM
connector and KNK1 of the knock control sensor.Resistance: 1 Ω or less
(d) Check for short between the terminals KNK1 and EKNKof the ECM connector.Resistance: 1 M Ω or more
NG REPAIR OR REPLACE HARNESS ANDCONNECTOR
OK
![Page 3: Knock sensor for Toyota NZE engine](https://reader030.fdocuments.in/reader030/viewer/2022020105/55305c9d4a7959de2a8b46f2/html5/thumbnails/3.jpg)
A64029
–DIAGNOSTICS SFI SYSTEM (1ZZ–FE)05–75
275Author: Date:
2003 COROLLA MATRIX (RM940U)
4 CONFIRM THE MALFUNCTION DISAPPEAR WHEN A GOOD KNOCK SENSOR ISINSTALLED
SST 09816–30010(a) Change the knock sensor to a new one
(1) Remove the knock control sensor.(2) Install the knock control sensor.Torque: 20 N ⋅m (204 kgf ⋅cm, 15 ft ⋅lbf)
(b) Perform the driving test.(c) Read DTC.
Result:A B
RESULT P0325 is output P0325 is not output
B REPLACE KNOCK CONTROL SENSOR
A
CHECK AND REPLACE ECM