8/9/2019 kissing-dolls_i_e_ltr.pdf

http://slidepdf.com/reader/full/kissing-dollsieltrpdf 1/4

Assemble the box mechanism

Glue tab

Scissors lineParts name

Parts No.

Attach to strengthenthe part you cut.

Do not attach theglue tabs on the bottom.

Kissing Dolls : Assembly Instructions Page

<Caution>

Keep scissors and glue away from small children.

Be careful not to cut your fingers when using scissors.

  marks a basic assembly technique that remains the same

regardless of the part.

Instructions are printed only for the first instance.

The Assembly instructions are divided into three blocks: A (box

mechanism) ,B (kissing dolls' bodies) and C (kissing dolls' heads).Follow the instructions for each block to assemble your kissing

dolls.

Use pattern: Page2 to Page7.

Cut along the line marked .

Cut out A1 by cutting along the lines.

Make a mountain fold on A1.

Trace along the mountain fold line with a pencil,scoring it to make it easier to fold.

Cut out the hole in A3, and attach A4. In the same way,attach A5 and A6.

Using the photo as a guide, attach in the direction of the arrow.

   A   1   B  o  x

Scissors

Paste, or woodwork glue

Stencil pen, or bodkin

Ruler

Scissors line

Mountain fold

Valley fold

Glue spot

Parts No.

Notation KeyTools

Attach A1, A2, A3 and A5 together, but do not glue the

glue tabs on the bottom yet.

Glue the back

8/9/2019 kissing-dolls_i_e_ltr.pdf

http://slidepdf.com/reader/full/kissing-dollsieltrpdf 2/4

Attach to the green area.

Do not attach theglue tabs on thebottom.

Align the shapesof the glue tabshere.

Fold in half and glue together.

Make it roundagain, and glue

together.

Check that both the

inside and outsideare correct.

Attach together sothat the shafts are parallel.

Attach together so thatthe shafts are parallel.

Poke the tip of A16 out through the top of the box. Poke the tip of A15 out through the top of the box.

Widen the box and

feed through the hole.

Match the colorsof these parts.

Face these partsinwards.

Kissing Dolls : Assembly Instructions Page

Attach A7 and A8 to the box.

Assemble A9 to A14.

Assemble A15 and A16.

Insert A9 through A15 and A16, and assemble A10 ~ A13.

Insert A9 through the box, and assemble A14.

Attach the parts for the bottom of the box.

Assemble A17 and A18, cut out the hole on A19, and attachA20 and A21. Then, attach A17 and A18 to that.

8/9/2019 kissing-dolls_i_e_ltr.pdf

http://slidepdf.com/reader/full/kissing-dollsieltrpdf 3/4

Make the kissing dolls' bodies

Use pattern: Page8 / Page9.

Insert A15 into A17,

and A16 into A18.

Align the shapes

of the glue tabs.

Attach the glue tabs

together according

to their shape.

Insert the arms

inside, and align

the shapes of theglue tabs.

Triangular glue tab

PageKissing Dolls : Assembly Instructions

Attach A19 to the box, and the box mechanism is complete.

Attach B1 to A17. Then, attach B2 and B3 to that.

Using the photo as a guide, move your fingers in the direction of the

arrow, adjusting the pressure to curl the paper.

Attach the triangular glue tabs so that the front side becomes convex.

Attach B4 to A17, and attach B5 to that.

Next, assemble B4 and B5.

Assemble B6 and B7, and attach them together. In the same

way, assemble B8 and B9. Next, attach B6 and B8 to B4.

Assemble B10 and B11, and attach them to B4.

In the same way, assemble the body parts B12 ~ B22.

8/9/2019 kissing-dolls_i_e_ltr.pdf

http://slidepdf.com/reader/full/kissing-dollsieltrpdf 4/4

Attach the triangularglue tabs so that thefront side becomes convex.

 C  3 H e a d 

Align the shapes of the glue tabs,and glue it precisely in place.

Align the shapesof the glue tabs.

If you have problems,adjust the angle here.

Align the shapes of the glue tabs,and glue it precisely in place.

Slowly rotate with your finger.

Close the open parts of C2and glue together.

Fold up the piece to roll it tightly,as shown in the photo.

Put glue on the blue areaand attach together.

Put glue on theblue area andattach together.

PageKissing Dolls : Assembly Instructions

Make the kissing dolls' heads

To prevent the heads from overbalancing, use only

a thin layer of glue when assembling.

Attach parts C1 ~ C4.

Use pattern: Page10 / Page11.

Attach C5 to C6, and attach that to the head.

In the same way, assemble the parts C7 ~ C13.Next, attach C14 to the head.

Fold up the pieceto roll it tightly,as shown inthe photo.

Place the dolls' heads on their bodies, and your kissing dolls are complete!