Kellogg Square - Granicus

Kellogg Square

LIGHT FIXTURE CUT SHEETS

November 4, 2013

156 West Alamar Ave. • Suite C • Santa Barbara, CA • 93105 • telephone (805) 682-8894 • fax (805) 898-9683 www.poirierandassociates.com

(See page 4 and page 5 for details on luminaire configurations.)

P32 32" PureForm Luminaire - Constant Wattage

P32-DCC 32" PureForm Luminaire - Dual Circuit Control

P32-DIM 32" PureForm with 0-10V Dimming

P32-MR501 32" PureForm with Motion Response - 50% Low , Pole Mounted Motion Sensor

P32-APD2 32" PureForm with Automatic Profile Dimming

P32-APD-MRO1 32" PureForm - APD with Motion Response Override, Pole Mounted Motion Sensor

Job:Type: Notes:

PREFIX

MOUNTING

1611 Clovis Barker Road, San Marcos, TX 78666 (800) 227-0758 (512) 753-1000 FAX: (512) 753-7855 sitelighting.com© 2012 Koninklijke Philips Electronics N.V. All Rights Reserved. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company’s continuing product improvement program.

G200-036/1012

1. MR50 and APD-MRO luminaires require one motion sensor per pole, ordered separately. See Accessories on page 2. Motion Response luminaires available 120V or 277V only.2. Available 120V through 277V only.

ARM (Omit for Mast Arm Mount luminaires)

Arm Style Available Mountings

A1 Standard 9" Arm Direct to Pole Mount and Wall Mount

A2 Short 5" Arm Direct to Pole Mount and Wall Mount

A3 Decorative Arm Direct to Pole Mount Only

Note: All Arm Styles shown above mount to a round pole with no adapter. If mounting to a square pole, specify the appropriate Square Pole Adapter option: SPA1-2 for A1 or A2 arms, SPA3 for A3 arms. See Options on page 2.

Enter the order code into the appropriate box above. Note: Philips Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory.

VOLTAGEMOUNTINGPREFIXOPTICAL SYSTEM LED WATTAGE FINISH OPTIONSLED SELECTIONARM

A1 - 9" Standard Arm Mount

A3 - Decorative Arm Mount MA - Mast Arm Mount

A2 - 5" Short Arm Mount

Direct to Pole Mount (Available with A1, A2 or A3 Arms)1 Single Pole Mount2 Twin Pole Mount at 180°2@90 Twin Pole Mount at 90°3 3-way Pole Mount at 90°3@120° 3-way Pole Mount at 120°4 4-way Pole Mount

Mast Arm MountMA Mast Arm Mount (Requires 2 3/8" OD Mast Arm)

Wall Mount (Available with A1 or A2 Arms Only. Not available in P32-MR50, or P32-APD-MRO.)W Wall MountWS Wall Mount, Surface Conduit

OPTICAL SYSTEM4 Featuring unitized optic lens construction.

Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available. All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms. All PureForm luminaires provide full cutoff performance.

PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance.

PureForm LEDP32 Area LuminairesPage 1 of 7

4. Luminaire door frame and optic assembly provided standard without glass lens. Specify CLR option for clear glass lens. See Options on page 2.

5. See pages 6 and 7 for information on optical rotation prior to ordering.

6. Available with 170LA or 260LA LED wattages only.

Optic Type

StandardOptic

Position

Optic Rotated

Left5 (90°)

Optic Rotated

Right5 (270°)

Type II 2 2-90 2-270

Type III 3 3-90 3-270

Type IV 4 4-90 4-270

Type V Medium 5M

Type V Wide 5W

Backlight Control BLC BLC-90 BLC-270

LEED Corner Cutoff Optics6 LCL LCR

S1

P32-MR50 1 260LA UNIV BRP A3 NW4








Job:Type: Notes:

PREFIX

MOUNTING


G200-036/1012























Optic Type

StandardOptic

Position

Optic Rotated

Left5 (90°)

Optic Rotated

Right5 (270°)

Type II 2 2-90 2-270

Type III 3 3-90 3-270

Type IV 4 4-90 4-270

Type V Medium 5M

Type V Wide 5W



S2

P32-MR50 1 160LA UNIV BRP A3 NW3








Job:Type: Notes:

PREFIX

MOUNTING


G200-036/1012























Optic Type

StandardOptic

Position

Optic Rotated

Left5 (90°)

Optic Rotated

Right5 (270°)

Type II 2 2-90 2-270

Type III 3 3-90 3-270

Type IV 4 4-90 4-270

Type V Medium 5M

Type V Wide 5W



S3

P32-MR50 1 160LA UNIV BRP A3 NW5W








Job:Type: Notes:

PREFIX

MOUNTING


G200-036/1012























Optic Type

StandardOptic

Position

Optic Rotated

Left5 (90°)

Optic Rotated

Right5 (270°)

Type II 2 2-90 2-270

Type III 3 3-90 3-270

Type IV 4 4-90 4-270

Type V Medium 5M

Type V Wide 5W



S4

P32-MR50 2 160LA UNIV BRP A3 NW5W


G200-036/1012

Page 2 of 7

10. Available with A1 arm or with MA mounting only. Provide specific input voltage. 11. Kits consist of 25 injection molded plastic bird deterrent spikes. Field installation only.12. Not available in 480V. Provide specific input voltage.13. Available with A1 or A2 arms, or with MA mounting only.

FINISH OPTIONSBRP Bronze Paint

BLP Black Paint

WP White Paint

NP Natural Aluminum Paint

OC Optional Color Paint Specify Optional Color or RAL ex: OC-LGP or OC-RAL7024.

SC Special Paint Specify. Must supply color chip.

F10 FusingLF In-Line/In-Pole Fusing BD11 Bird Deterrent Spike KitPC12,13,14 Photocontrol and Receptacle PCR13,14 Photocontrol Receptacle onlyPCB12,13,14 Button Photocontrol EHHS External Houseside ShieldPTF2 Pole Top Fitter - 2 3/8" - 3" Dia. TenonPTF3 Pole Top Fitter - 3" - 3 1/2" Dia. TenonPTF4 Pole Top Fitter - 3 1/2" - 4" Dia. TenonSPA1-2 Square Pole Adapter (for use with A1 or A2 Arms)SPA3 Square Pole Adapter (for use with A3 Arms)

DL Diffusing Lens (reduces performance significantly)CLR Clear Glass Lens (reduces performance)POLY15 Polycarbonate Lens (reduces performance)SPR16 Surge Protection for 120V through 277V Input meeting ANSI C62.41.2SPRH16 Surge Protection for 347V through 480V Input meeting ANSI C62.41.2TB Terminal BlockTL Provides for access to the LED arrays and driver without tools

ACCESSORIES (Ordered separately)MS-P 120V or 277V Input - Pedestrian Motion Sensor for P32-MR50 (Motion Response) or P32-APD-MRO (Automatic Profile Dimming with Motion Response Override)MS-A-120V 120V Input - Area Motion Sensor for P32-MR50 (Motion Response) or P32-APD-MRO (Automatic Profile Dimming with Motion Response Override)MS-A-277V 277V Input - Area Motion Sensor for P32-MR50 (Motion Response) or P32-APD-MRO (Automatic Profile Dimming with Motion Response Override)

Motion Sensors are ordered separately, with one (1) motion sensor required per pole location for P32-MR50 or P32-APD-MRO luminaires. See Luminaire Configuration Information on page 4-5 for more details. Pedestrian sensor color is white. Area motion sensor color is Arctic White.

LED SELECTION VOLTAGECW Cool White - 5700°K - 75 CRI Nominal NW Neutral White - 4000°K - 70 CRI NominalWW Warm White - 3000°K - 80 CRI Nominal

UNIV 120V through 277V, 50hz or 60hzHVU 347V through 480V, 50hz or 60hz (High Voltage Universal)

Ordering Code

Average System Watts7

LED Current

(mA)

LED Quantity -Dual LED Array

LED Selection

Luminaire Initial Absolute Lumens8,9

TYPE 2 TYPE 3 TYPE 4 TYPE 5M TYPE 5WPer LED Array

TotalLEDs

110LA 110 350 48 96 NW 8,997 (s) 9,340 (s) 8,687 10,286 (s) 10,901(s)

140LA 140 350 64 128 NW 11,947 (s) 12,380 (s) 11,599 (s) 13,659 (s) 14,475 (s)

170LA 170 350 80 160 NW 14,749 15,204 (s) 14,320 16,863 17,870

160LA 160 530 48 96 NW 12,423 (s) 13,249 (s) 12,263 14,400 (s) 15,580

210LA 210 530 64 128 NW 16,496 (s) 17,593 (s) 16,330 (s) 19,122 (s) 20,638

260LA 260 530 80 160 NW 20,366 21,720 20,161 23,607 25,838

7. Wattage may vary by +/- 8% due to LED manufacturer forward volt specification and ambient temperature. Wattage shown is average for 120V through 277V input. Actual wattage may vary by an additional +/- 10% due to actual input voltage. 8. Values shown are for luminaires without the CLR, DL or EHHS options. Tests are in process for configurations not shown. “(s)” following the value indicates that values are scaled from tests on similar, but not identical luminaire configurations. Contact Gardco.applications@ philips.com if any approximate estimates are required for design purposes. 9. Lumen values based on tests performed in compliance with IESNA LM-79.

LED WATTAGE AND LUMEN VALUES

14. Not available in P32-DCC. 15. Polycarbonate lenses feature a 1 year warranty only.16. Not available with Fusing (F) option.

PureForm LEDP32 Area Luminaires

of 7


WITH A2 SHORT ARM


G200-036/1012

DIMENSIONS AND EPAA1 STANDARD ARM MOUNT A2 SHORT ARM MOUNT MA MAST ARM MOUNT

WALL MOUNT

20.3" / 51.562cm 20.3" / 51.562 cm

36.43"/ 95.532 cm

A3 DECORATIVE ARM MOUNT

B = 9.21" 23.394 cm

40.53" / 102.946 cm

E = 10.25" 26.035 cm

A

A = 6.53" 16.586 cm

C

C = 5.73" 14.554 cm

D = 3.68" 9.347 cm

F = 10.06" 25.552 cm

F

17.41" 44.221 cm

48.74" / 123.8 cm

G = 7.25" 18.415 cm

K

42.62" / 108.255 cm

H = 11.29" 28.677 cm

38.51" / 97.815 cm

L= 7.18" 18.237 cm

L

WITH A1 STANDARD ARM

K = 7.25" 18.415 cm

Single Luminaire Weight

MountingApproximate

Weight

A1 57 lbs / 25.865 kg

A2 56 lbs / 25.402 kg

A3 60.5 lbs / 27.443 kg

MA 57 lbs / 25.865 kg

W or WS 58 lbs / 26.309 kg

Effective Projected Area ft2 / m2

Mounting Single Twin @ 180 3/4

A1 0.40 / 0.038 0.80 / 0.075 1.65 / 0.154

A2 0.35 / 0.033 0.70 / 0.066 1.45 / 0.135

A3 0.55 / 0.052 1.10 / 0.103 2.0 / 0.186

MA 0.40 / 0.038 N/A N/A

B

Maximum Profile (All Models) = 3.0" / 7.62 cm

5.1" / 12.954 cm

D

41.58"/ 105.613 cm

20.3" 51.562 cm

E

G

H

20.3" / 51.562 cm

FF = 10.06" 25.552 cm

A

A = 6.53" 16.586 cm

C

C = 5.73" 14.554 cm

D

D = 3.68" 9.347 cm

Black, 120V OR 277V Input

White - NeutralSensor

Red Connects to Override Input (Orange) Line of DynaDimmer

90°

9.5ft(3m)

25ft(8m)

52.5ft(16m)

8ft(2.4m)

90°

1H

Height

6H3H

Distances are approximate.

H= Height Above Ground

270° Front Coverage


G200-036/1012

Additional Hand Hole 15' Above Pole Base(oriented 180° to the standard hand hole)

Motion Sensor

Cover Plate with 1/2" NPT Coupling (supplied with pole)

Wiring in

Pole

Mounting to a Philips Gardco Pole

Attach Motion Sensor to Cover Plate coupling, Complete Wiring in Pole and Attach Cover Plate to Hand Hole

LUMINAIRE CONFIGURATION INFORMATION (CONTINUED ON PAGE 5)

100%

100%

50% 50%

Power On Mid Point

2 Hours 6 Hours

Power Off

Page 4 of 7

Neutral

120V OR 277V power input

BlackSensor

White

Red Red Connects to Override Input (Orange) Line of DynaDimmer

Side Coverage Pattern Top Coverage Pattern

1H2H 2H

Distances are approximate. H = Height above ground.


P32: Philips Gardco PureForm LED standard luminaire providing constant wattage and constant light output when power to the luminaire is energized.

P32-DCC: Philips Gardco PureForm luminaires provided with dual circuiting, permitting separate switching of each led array.

P32-DIM: Philips Gardco PureForm LED luminaire provided with 0 -10V dimming for connection to a control system provided by others.

P32-MR50: Philips Gardco PureForm LED luminaire with motion response, providing a 50% power reduction on low and a commensurate reduction in light output. The power and light output reduction is accomplished utilizing the Philips DynaDimmer module, programmed for a constant 50% power. Power supplied by the motion sensor connected to the override line on the DynaDimmer takes the luminaire to high setting, 100% power and light output, when motion is detected. The luminaire remains on high until no motion is detected for the motion sensor duration period, after which the luminaire returns to low. Duration period is factory set at 15 minutes, and is field adjustable from 5 minutes up to 15 minutes.

This configuration is not available for use with wall mounted luminaires.

P32-MR50 is available in 120V through 277V input only to the luminaire. Motion sensors require single voltage 120V or 277V input.

The Area PIR motion sensor is the WattStopper EW-200-120-W (120V Input - MSA-120V) or the WattStopper EW-200-277-W (277V Input - MSA-277V.) One motion sensor per pole is required and is ordered separately. Area sensors require single voltage 120V or 277V input.

The area motion detector provides coverage equal to up to 6 times the sensor height above ground, 270° from the front-center of the sensor.

Area PIR Motion Sensor Coverage Pattern:

The Pedestrian PIR motion sensor is the WattStopper HB350W-L3. One motion sensor per pole is required and is ordered separately as the MS-P accessory, see page 2. The Pedestrian sensor accept 120V or 277V input.

The pedestrian motion detector provides coverage equal to the sensor height above ground, in all directions from the sensor (360°.) For longer range detection applications, The area motion sensor is recommended.

Motion response requires that the pole include an additional hand hole 15 feet above the pole base, normally oriented 180° to the standard hand hole. For Philips Gardco poles, order the pole with the Motion Sensor Mounting (MSM) option which includes the hand hole and a special hand hole cover plate for the sensor with a 1/2" NPT receptacle centered on the hand hole cover plate into which the motion sensor mounts. Once the motion sensor is connected to the hand hole cover plate, then wiring connections are completed in the pole. The plate (complete with motion sensor attached and wired) is then mounted to the hand hole. If poles are supplied by others, the customer is responsible for providing suitable mounting accommodations for the motion sensor in the pole.

P32-APD: Philips Gardco PureForm LED luminaire with Automatic Profile Dimming. Luminaire is provided with a programmable LED Driver. The programmable LED Driver is programmed to go to 50% power, 50% light output two (2) hours prior to night time mid-point and remain at 50% for six (6) hours after night time mid-point. Mid-point is continuously recalculated by the programmable LED Driver based on the average mid-point of the last two full night cycles. Short duration cycles, and power interruptions are ignored and do not affect the determination of mid-point.

P32-APD is available in 120V through 277V input only.

P32-APD Dimming Profile:

The P32-APD offers many of the advantages of a sophisticated control system, including an average energy savings of at least 33% versus constant wattage, constant light output systems, without the need for a control system.

P32-APD-MRO: Philips Gardco PureForm LED luminaire with Automatic Profile Dimming, with Motion Response Override. The P32-APD-MRO combines the benefits of both automatic profile dimming and motion response, using the Philips DynaDimmer module. The luminaire will dim to 50% power, 50% light output, per the dimming profile shown for the P32-APD. If motion is detected during the time that the luminaire is operating at 50%, the luminaire returns to 100% power and light output. The luminaire remains on high until no motion is detected for the duration period, after which the luminaire returns to low. Duration period is factory set at 15 minutes, and is field adjustable from 5 minutes up to 15 minutes.

This configuration is not available for use with wall mounted luminaires.

P32-APD-MRO is available in 120V through 277V input only to luminaire. The motion sensor requires either 120V or 277V input to the motion sensor.

The P32-APD-MRO has the same pole requirements and utilizes the same motion sensors as the P32-MR50. The motion sensor mounts and wires identically as well. The P32-APD-MRO utilizes the identical dimming profile as shown for the P32-APD.

By combining the benefits of automatic profile dimming and motion response, the P32-APD-MRO assures maximum energy savings, and insures that adequate light is present if motion is detected.

Note: All motion sensors utilized consume 0.0 watts in the off state.

Page 5 of 7

GENERAL DESCRIPTION: Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms.

HOUSING: The PureForm features a die cast aluminum housing, and mounts directly to a pole or wall. The low profile rounded form reduces the effective projected area of the luminaire significantly.

PureForm luminaires supplied with A1, A2 and A3 arms are provided with arms firmly attached to the main luminaire housing body. As a result, the luminaires provide the functionality, strength and installation ease of an integral arm luminaire.

Mast arm mount luminaires are provided with the mast arm mounting assembly firmly attached to the main luminaire housing body.

IP RATING: PureForm luminaires have a rating of IP66.

VIBRATION RESISTANCE: PureForm carries a 3G vibration rating that conforms to standards set forth by ANSI C136.31. Testing includes vibration to 3G acceleration in three axes, all performed on the same luminaire.

OPTICAL SYSTEMS: The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available, both as LCR (right) and LCL (left.) All optical systems feature unitized lens optic construction.

Types 2, 3, 4, BLC and LCR/LCL optical systems utilize an innovative redirecting reflector system to complement the performance of the LED optic. The redirecting reflector system includes a black surrounding surface to minimize aperture brightness when viewed from the rear of the luminaire.

PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance. All PureForm luminaires provide full cutoff performance.

LED RELIABILITY:

PREDICTED LUMEN DEPRECIATION DATA

Ambient Temperature °C Driver mA L70 Hours17

25 °C350 mA 240,000

530 mA 165,000

40 °C350 mA 215,000

530 mA 148,000

17. Predicted performance derived from LED manufacturer’s data and engineering design estimates, based on IESNA LM-80 methodology. Actual experience may vary due to field application conditions. L70 is the predicted time when LED performance depreciates to 70% of initial lumen output.

THERMAL MANAGEMENT: The Philips Gardco PureForm LED provides die cast aluminum integral thermal radiation fins to provide the excellent thermal management so critical to long LED system life.

ELECTRICAL: Luminaires are equipped with an LED driver that accepts 120V through 277V, or 347V through 480V, 50hz to 60hz, input. Driver output is based on the LED wattage selected. Component-to-component wiring within the luminaire will carry no more than 80% of rated current and is listed by UL for use at 600 VAC at 302°F / 150°C or higher. Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. Power factor is not less than 90%. Luminaire consumes 0.0 watts in the off state. All motion sensors utilized consume 0.0 watts in the off state.

FINISH: Each standard color luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard colors include bronze (BRP), black (BLP), white (WP), and natural aluminum (NP). Consult factory for specs on optional or custom colors.

LABELS: All luminaires bear UL or CUL (where applicable) Wet Location labels.

WARRANTY: Philips Gardco luminaires feature a 5 year limited warranty. Philips Gardco LED luminaires with LED arrays feature a 5 year limited warranty covering the LED arrays. LED Drivers also carry a 5 year limited warranty. Motion sensors are covered by warranty for 5 years by the motion sensor manufacturer. See Warranty Information on www.sitelighting.com for complete details and exclusions. Polycarbonate lenses carry a 1 year warranty.

SPECIFICATIONS

FULL CUTOFF PERFORMANCE: Full cutoff performance means a luminaire distribution where zero candela intensity occurs at an angle at or above 90° above nadir. Additionally, the candela per 1000 lamp lumens does not numerically exceed 100 (10 percent) at a vertical angle of 80° above nadir. This applies to all lateral angles around the luminaire.

LUMINAIRE CONFIGURATION INFORMATION (CONTINUED FROM PAGE 4)


G200-036/1012


of 7


ASYMMETRIC OPTICAL ORIENTATION INFORMATION (CONTINUED ON PAGE 7)

STANDARD OPTIC POSITION: Luminaires ordered with asymmetric optical systems in the standard optic position will have the optical system oriented as shown below:

RIGHT Side of Pole

Street Side

House Side

Curbline

LEFT Side of Pole

0°

270°

180°

90°

Note: The hand hole will normally be located on the pole at the 0° point.

OPTIC ROTATED LEFT (90°) OPTIC POSITION: Luminaires ordered with asymmetric optical systems in the OPTIC ROTATED LEFT (90°) optic position will have the optical system oriented as shown below:

RIGHT Side of Pole

Street Side

House Side

Curbline

LEFT Side of Pole

0°

270°

180°

90°



G200-036/1012

of 7



G200-036/1012

0°

270°

180°

90°

Note: The hand hole location will depend on the drilling configuration ordered for the pole.

OPTIC ROTATED RIGHT (270°) OPTIC POSITION: Luminaires ordered with asymmetric optical systems in the OPTIC ROTATED RIGHT (270°) optic position will have the optical system oriented as shown below:

RIGHT Side of Pole

Street Side

House Side

Curbline

LEFT Side of Pole

0°

270°

180°

90°


ASYMMETRIC OPTICAL ORIENTATION INFORMATION (CONTINUED FROM PAGE 6)

TWIN LUMINAIRE ASSEMBLIES WITH ROTATED OPTICAL SYSTEMS:Twin luminaire assemblies installed with rotated optical systems are an excellent way to direct light toward the interior of the site (Street Side) without additional equipment. It is important, however, that care be exercised to insure that luminaires are installed in the proper location.

RIGHT Side of Pole

Street Side

House Side

Curbline

LEFT Side of Pole

Luminaires with Optic Rotated Right (270°) are installed on the LEFT Side of Pole

Luminaires with Optic Rotated Left (90°) are installed on the RIGHT Side of Pole

Nipples and Couplings

Indicate size (1/2", 3/4", 1", 1 1/4", 1 1/2". ) Indicate height above base and orientation to hand hole. See Pole Orientataion Information on Page 4.

NL Nipple - External thread

CL Coupling - Internal thread

VDA Vibration Dampener

Single Mount Bullhorn Brackets

Indicate height above base and orientation to hand hole. See Pole Orientation Information on Page 4.A15BH-19 Single - 1.9" ODA15BH-24 Single - 2.4" ODA215BH-19 2-Tenon - 1.9" ODA215BH-24 2-Tenon - 2.4" OD

Motion Response Provisions

GMR Provision for Gardco HIDMotion Response System

Minimum Pole Height is 18'. Includes a 1/2" coupling placed 180° to the hand hole, 12' above the pole base.

MSM Motion Sensor Mounting Provision for LED Luminaires available with Motion Response

Minimum Pole Height is 18'. Includes a special hand hole with 1/2" coupling placed in the cover plate, 180° to the hand hole, 15' above the pole base.

RA4.5

Job:Type: Notes:

Poles4.5" Straight Round Aluminum - Cast BasePage 1 of 4

The Philips Gardco RA4.5 straight aluminum pole consists of a one-piece 4.5" round extruded aluminum lighting standard mounted to a cast aluminum base. The poles are finished with either Architectural Class 1 anodizing or electrostatically applied TGIC polyester powdercoat. All poles include anchor bolts, full base cover, hand hole, ground lug and top cap.

PREFIX BASE

FINISH

CB Fixed Cast Base


79415-35/0611

PREFIX BASE DRILLINGHEIGHT FINISH OPTIONS

Enter the order code into the appropriate box above. Note: Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory.

HEIGHT10'12'15'18'20'

OPTIONS

DRILLING

BRP Bronze PaintBLP Black PaintWP White PaintNP Natural Aluminum PaintBRA Bronze AnodizedBLA Black AnodizedNA Natural AnodizedOC Optional Color Paint Specify Optional Color or

RAL ex: OC-LGP or OC-RAL7024.

SC Special Color Paint Specify. Must supply color chip.

Hinged Bases are available for this pole size. Please refer to Hinged Base Pole sheet

79415-8 for specifications and dimensions.

DR

GFCI

Duplex ReceptacleGround Fault Receptacle

D1D2D2@90D3D3@120D4T2T4

1 Way 2 Way2 Way at 90°3 Way3 Way at 120°4 Way2 3/8" OD Tenon4" OD Tenon

S1,S2,S3 =D1, S4 = D2

RA45 20CB BRP

of 4

Poles4.5" Straight Round Aluminum - Cast Base

POLE DATA

DIMENSIONS

CATALOG NUMBER

POLE SIZE MAXIMUM LUMINAIRE LOADING1 ANCHOR BOLT DATA2

PREFIX - BASE - HEIGHTACTUAL HEIGHT

WALLTHICKNESS

(inches.)

100 MPH

EPA-FT2

90 MPH

EPA-FT2

80 MPH

EPA-FT2

BOLT CIRCLE(inches)

BOLT SIZE(inches)

MAX PROJ.(inches)

RA4.5-CB-10 10' .125 7.6 9.5 12.5 7 - 8.625 3/4 x 17 x 3 3.25"

RA4.5-CB-12 12' .125 5.6 7.1 9.5 7 - 8.625 3/4 x 17 x 3 3.25"

RA4.5-CB-15 15' .188 5.1 6.5 8.8 7 - 8.625 3/4 x 17 x 3 3.25"

RA4.5-CB-18 18' .188 3.6 4.7 6.7 7 - 8.625 3/4 x 17 x 3 3.25"

RA4.5-CB-20 20' .188 2.4 3.2 5.1 7 - 8.625 3/4 x 17 x 3 3.25"

1. Warning: Additional wind loading, in terms of EPA, from banners, cameras, floodlights and other accessories attached to the pole, must be added to the luminaire(s) EPA before selecting the pole with the appropriate wind load capability.

2. Factory supplied template must be used when setting anchor bolts. Philips Gardco will not honor any claim for incorrect anchorage placement resulting from failure to use factory supplied templates.


79415-35/0611

E

CONDUITOPENING

HANDHOLEREINFORCEMENT

MAXIMUM B

MINIMUM B

TAPPED 3/8"-16FOR GROUNDCONNECTOR

A

D

CCAST ALUMINUM

NUT COVER

F

TAPPED 3/8"-16FOR GROUNDCONNECTOR

HANDHOLE DETAIL

NOTE: Factory supplied template MUST be used when setting anchor bolts. Philips Gardco will not honor any claim for incorrect anchorage placement from failure to use factory supplied templates.

Tapped 3/8" - 16 for Ground Connector

Tapped 3/8" - 16 for Ground Connector

Hand hole DetailHand hole

Reinforcement

Conduit Opening

Bolt Circle7" Minimum

4.125"

3.25"

Bolt Circle 8.625"

Maximum

AnchorBolt

Length

8 3/4"

Supplied with a Full Base Cover

(not shown)

4.5"

DESIGN: The poles as charted are designed to withstand dead loads and predicted dynamic loads developed by variable wind speeds with an additional 30% gust factor under the following conditions:

The charted weights include luminaire(s) and/or mounting bracket(s).

The wind velocities are based on 10 mph increments from 80 mph through 100 mph. Poles to be located in areas of known abnormal conditions may require special consideration. For example: coastal areas, airports and areas of special winds.

Poles are designed for ground mounted applications. Poles mounted on structures (such as buildings and bridges) may also necessitate special consideration requiring Philips Gardco’s recommendation.

Height correction factors and drag coefficients are applied to the entire structure. An appropriate safety factor is maintained based on the minimum yield strength of the material incorporated in the pole.

WARNING: This design information is intended as a general guideline only. The customer is solely responsible for proper selection of pole, luminaire, accessory and foundation under the given site conditions and intended usage. The addition of any items to the pole, in addition to the luminaire, will dramatically impact the EPA load on that pole. It is strongly recommended that a qualified professional be consulted to analyze the loads given the user’s specific needs to ensure proper selection of the pole, luminaire, accessories, and foundation. Philips Gardco assumes no responsibility for such proper analysis or product selections. Failure to insure proper site analysis, pole selection, loads and installation can result in pole failure, leading to serious injury or property damage.

GENERAL INFORMATION: Mounting height is the vertical distance from the base of the lighting pole to the center of the luminaire arm at the point of luminaire attachment.Twin arms as charted are oriented at 180° with respect to each other. For applications of two (2) arms at 90° or other multiple arm applications, consult the factory.

WARRANTY: Philips Gardco poles feature a 1 year limited warranty. See Warranty Information on www.sitelighting.com for complete details and exclusions.

GENERAL POLE INFORMATION

All aluminum alloys shall comply with metallurgical and mechanical properties set forth in the Aluminum Association Standards.

POLE SHAFT: The shaft shall be extruded from all new seamless 6063 alloy aluminum and shall be heat treated to produce a T6 temper. The shaft shall be polished with fine grain aluminum oxide cloths, resulting in a high quality circumferential satin brushed finish. After finishing, each pole shall be fully tire-wrapped with neutral PH krinkle/kraft paper for protection in shipment. .

ANCHOR BASE: The anchor base is cast from A356 alloy aluminum. The shaft shall be inserted into the anchor base casting. The anchor base casting and shaft shall be joined by a continuous circumferential weld at the inside bottom of the anchor base. The completed assembly shall be heat treated to a T6 condition. A full base cover shall be included with each anchor base.

ANCHOR BOLTS: Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds a minimum guaranteed yield strength of 50,000 psi. Bolts have an “L” bend on one end and threaded on the opposite end. Anchor bolts are completely hot dipped galvanized. Four (4) properly sized bolts, each furnished with two (2) regular hex nuts and two (2) flat washers, are provided per pole, unless otherwise specified.

HAND HOLE: All poles shall include a peripherally reinforced flush covered hand hole centered 18" above the bottom of the pole. The opening shal measure 3" X 5".

POLE TOP CAP: Each pole assembly is provided with a removable composite friction-fit pole top cap.

FINISH: Poles are available with bronze, natural or black Aluminum Association Architectural Class 1 anodized finish. Electrostatically applied, thermally cured TGIC polyester powdercoat finish or liquid polyurethane is also available.

Page 3 of 4

SPECIFICATIONS


79415-35/0611


HAND HOLE

0°

270°

180°

90°

HAND HOLE

0°

270°

180°

90°

D1 Drilled for Single Luminaire D2 Drilled for 2 Luminaires at 180° D3 Drilled for 3 Luminaires @ 90°

300° from Hand Hole

60° from Hand Hole

For Factory Installed Options and Accessories, Specify Orientation from Hand Hole and Height Above Pole Base Where Required.

Height Above Pole Base

HAND HOLE

0°

270°

180°

90°

0°

270°

180°

90°

HAND HOLE

0°

270°

180°

90°

HAND HOLE

270°

180°

90°

HAND HOLE

270°

180°

90°

D2

D2

D3

D3 D3

D4

D4 D4

D4

D1

D2@90 D3@120

D2@90

D3@120

D4 Drilled for 4 Luminaires at 90° D2@90 Drilled for 2 Luminaires at 90° D3@120 Drilled for 3 Luminaires at 120°

D3@120

Orientation is measured clockwise from the Hand Hole Center.

Luminaire location

STANDARD ARM MOUNT LUMINAIRE ORIENTATION

FACTORY INSTALLED OPTIONS AND ACCESSORIES

ORIENTATION INFORMATION

HAND HOLE

0° 0°

Page 4 of 4



79415-35/0611

Shown on a Power Canopy™in Black Satin (BLP) finish

SIGN STAR™ l 8 WATT

Unprecedented solid-state performance in a timeless style. By combining the classic design

aesthetics of an RLM dome with our cutting edge BKSSL™ ‘e’ technology, we’ve taken sign

lighting to a whole new level. Sign Star™ Style D is configurable up to 48 inches in length.

Beneath the stylized dome is a fully adjustable solid-state source to place light exactly where

desired. Keyword SN-D

SN

Wide Flood

Medium Flood

Spot

Narrow Spot

OPTICS

Rectilinear

STYLE D

CCT

3K 4K

R

G B

A

MATERIAL

ALU

VOLTAGE

• 120-277V ••• 12V •

2� W W W . B K S S L . C O M

SIG

NLI

GH

TS

21 1/4"(540mm)

10 3/4" Dia.(273mm)

3/8"(10mm)

RLMReflector45°

(1219mm)

Specify Length48" Maximum

1" Dia. (25mm)

21 1/4"(540mm)

10 3/4" Dia.(273mm)

3/8"(10mm)

RLMReflector45°

(1219mm)

Specific Length48" Maximum

1" Dia. (25mm)

2�W W W . B K S S L . C O M

SIG

NLI

GH

TS

3/8"(10mm)

4"(102mm)

7 9/16"(192mm)

3" Dia(76mm)

CATSKILL™ l 15 WATT • 120V-277V

The Catskill Series™ is designed for architectural up lighting or down lighting applications.

With a projection of only four inches, the Catskill Series™ meets the ADA requirements

for Architectural Surface lighting. The addition of our ‘X’ technology makes this fixture a

stylish and smart addition to any indoor or outdoor application. Visit www.bklighting.com

for ordering logic. Keyword CK -LED

CK

Shown with 'C' cap in Black Chrome (BCM) �nish

‘B/E’ CAP

‘C’ CAP

‘A/D’ CAP

‘E’ CAP

‘C’ CAP

‘D’ CAP

‘E’ CAP

‘C’ CAP

‘D’ CAP

PM2 DRM/RM PM2DRM

DRIVER HOUSINGS:

84 W W W . B K S S L . C O M

ARC

HIT

ECTU

RAL

SURF

ACE

W W W . B K S S L . C O M

Wide Flood

Flood

Spot

OPTICS

Rectilinear

MATERIAL

ALU

VOLTAGE

• 120-277V ••

2.7K

CCT

3K 4K

LED [Remote Transformer]

Shown with Mitique™ Brass Finish (MIT)

Private Residence • Lighting D

esign by Randall W

hitehead • Photo ©

Doug Salin

6

7

GreenSource Initiative™

Metal and packaging components are made fromrecycled materials. Manufactured using renewablesolar energy, produced onsite. Returnable tomanufacturer at end of life to ensure cradle-to-cradlehandling. Packaging contains no chlorofluorocarbons(CFC's). Use of this product may qualify forGreenSource efficacy and recycling rebate(s). Consultwww.bklighting.com/greensource for programrequirements.

Materials

Furnished in Copper-Free Aluminum (Type 6061-T6),Brass (Type 360) or Stainless Steel (Type 316).

Body

Fully machined from solid billet. Unibody designprovides enclosed, water-proof wireway and integralheat sink for maximum component life. Integralknuckle for maximum mechanical strength. Hightemperature, silicone 'O' Ring provides water-tightseal.

Knuckle

'Aim and Lock' knuckle is comprised of twocomponents. The first is integral to the body andfeatures an interior, machined taper. The second ismachined from solid billet and features a second,reverse angle taper. The resultant mechanical taper-lock allows a full 180° vertical adjustment without theuse of serrated teeth, which inherently limit aiming.High temperature, silicone 'O' Ring provides water-tight seal and compressive resistance to maintainfixture position. Design withstands 73 lb. static loadprior to movement to ensure decades of opticalalignment. Biaxial source control with 360° horizontalrotation in addition to vertical adjustment.

Cap

Fully machined. Accommodates [1] lens or louvermedia. Choose from 45° cutoff ('A' or 'D'), 1” deep bezelwith 90° cutoff ('B' or 'E'), or flush lens ('C') cap styles.'A' and 'B' caps include weep-hole for water and debrisdrainage. 'D' and 'E' caps exclude weep-hole and arefor interior use only.

Lens

Shock resistant, tempered, glass lens is factoryadhered to fixture cap and provides hermeticallysealed optical compartment. Specify soft focus (#12)or rectilinear (#13) lens.

BKSSL™

Integrated solid state system with 'e' technology isscalable for field upgrade. Modular design withelectrical quick disconnects permit field maintenance.High power, forward throw source complies with ANSIC78.377 binning requirements. Exceeds ENERGYSTAR® lumen maintenance requirements. LM-80certified. Integral non-dimming driver. Minimum50,000 hour rated life at 70% of initial lumens (L70).BKSSL technology provides long life, significantenergy reduction and exceptional thermalmanagement.

Optics

Interchangeable OPTIKIT™ modules permit fieldchanges to optical distribution. Color-coded for easyreference.

Installation

Machined anchor base with 7/8”dia. slip conduit holeand [3] 3/16” dia. anchor bolt holes (hardware byothers). Available in standard increments to facilitatefixture elevation above grade. Optional 18” PowerPipe™ for direct burial into soil or concrete. PowerPipe™ additionally features optional 6” diameter,molded stability flange, which simplifies installation

and projects into substrate to reinforce housingstability. Optional 5” dia. machined canopy permitsmounting to junction box (gasket by others). 6”maximum base height for canopy-mounted brass orstainless steel fixture.

Transformer

For use with 12VAC remote transformer.

Wiring

Teflon® coated, 18AWG, 600V, 250° C rated andcertified to UL 1659 standard.

Hardware

Tamper-resistant, stainless steel hardware. Knucklevertical aiming screw is additionally black oxidetreated for additional corrosion resistance.

Finish

StarGuard® (Pat. Pend.), a RoHs compliant, 15 stagechromate-free process cleans and conversion coatsaluminum components prior to application of Class 'A'TGIC polyester powder coating. Brass components areavailable in powder coat or handcrafted metal finish.Stainless steel components are available inhandcrafted metal finish. (Brushed finish for interioruse only).

Warranty

5 year limited warranty.

Certification and Listing

ITL tested to IESNA LM-79. Lighting Facts Registrationper USDOE (www.lightingfacts.com). ETL Listed toANSI/UL Standard 1838 and UL Standard 8750.Certified to CAN/CSA Standard C22.2 No. 9. RoHscompliant. Suitable for indoor or outdoor use.Suitable for use in wet locations. Suitable forinstallation within 4’ of the ground. Made in USA.

Catalog Number Logic

Lens 12 - Soft Focus Lens (Standard)13 - Rectilinear Lens

Cap Style

Shielding11 - Honeycomb Baffle

Base Height3 - 3'' with Anchor Base (Standard)6 - 6'' with Anchor Base

12 - 12'' with Anchor Base18 - 18'' with Anchor Base24 - 24'' with Anchor Base

OptionPP - Power Pipe™ option with 18'' StakeSF - Stability Flange (for use with Power Pipe™)

WM - Wall or Ceiling Mount with 5'' dia. canopy**Base height limited to 6'' max. with brass and stainless steel fixtures.

Material Series Source Housing Lamp Optics Finish Lens Shielding Cap Style Base Height Option

B - AR - LED - RM - e23 - MFL - MAC - 12 - - A - 12 - PP

Specifications

1 1/2"

4 1/2"3 1/8"

2"

2 3/8"7/8"

7/8" Dia

2 1/4" Dia1/4" Dia120° Apart

5/8"

5" Dia

3 1/2" O.C.

“A/D” Cap

“B/E” Cap

“C” Cap

“F” Cap

STANDARD BASE

WALL MOUNT CANOPY

POWER PIPE

2 1/4" Dia

3"

1/8"

4 1/2"

A - 45° B - 90° C - FlushD - 45° less weephole

(for Interior Use Only)E - 90° less weephole

(for Interior Use Only)F - 90° cutoff

with flush lens

For lampinformation,see page 40.

See Pages 38-39 for additional finish choices

Series AR - ArtiStar™

SourceLED - Solid State System with Integral Driver

LED Type

Powder Coat Color Satin Wrinkle

Bronze BZP BZW

Black BLP BLW

White (Gloss) WHP WHW

Aluminum SAP —

Verde — VER

Aluminum & Brass Finishes

Machined MAC

Polished POL

Mitique™ MIT

Brass

MaterialBlank - Aluminum

B - BrassS - Stainless Steel

e22 - 8WLED/3Ke23 - 8WLED/4Ke24 - 8WLED/Red

e25 - 8WLED/Greene26 - 8WLED/Bluee27 - 8WLED/Amber

Finish

HousingRM - Requires Remote Transformer

OpticsNSP - Narrow Spot (Red Indicator)

SP - Spot (Green Indicator)MFL - Medium Flood (Yellow Indicator)WFL - Wide Flood (Blue Indicator)

Machined MAC

Polished POL

BrushedInterior Use only BRU

Stainless Steel

Kellogg Square - Granicus

Documents

Transcript of Kellogg Square - Granicus