kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with...

5
Tools you will need To put your kaboodle kitchen cabinets together you will need the following tools. Hardware included 28mm wood screws x 44 50mm wood screws x 29 E F C D B A I H G 14mm wood screws x 160 metal sided pot drawers pairs x 1 metal sided drawers pairs x 2 90° angle bracket x 5 16mm wood screws x 12 adjustable legs x 4 m3.5 14mm screws x 2 step 1 Follow these instructions to build and attach your cabinet. Things you need to know Pencil Cordless drill with: • Number 2 screw tip • 4mm drill bit • Number 12 countersinking drill bit Tape measure Wall fixing (If necessary) Adjustable square 65mm wood screw Clamps (quick release) Safety gear Spirit level (900mm recommended) p. 1 Ver. 9 W-70121 • Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back option make sure you pack out the back of your cabinet before screwing into the wall. • All cabinets will need to be attached to the wall using a minimum of 8 gauge 65mm screws if you have a stud wall. If your wall is concrete, brick or another surface ask your hardware specialist for advice on the right fixing method. • Make sure you leave plumbing and electrical work to qualified trades people. Never try this yourself. • For extra strength use exterior woodworking glue when assembling cabinets. • To help identify panels, counter sunk holes always face outwards. • All holes that aren’t already pre-drilled should be drilled prior to screwing using a No 12 countersinking drill bit. • Make sure you always use safety gear like a mask, ear muffs and glasses when using tools. • If you have any questions, contact us on: Australia: 1800 666 078 Monday to Friday between 8:00am and 6:00pm AEST, New Zealand: 0800 522 663 Monday to Friday between 8:00am and 5:00pm NZST or email: [email protected]. 600mm 3 drawer base cabinet

Transcript of kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with...

Page 1: kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back

Tools you will needTo put your kaboodle kitchen cabinets together you will need the following tools.

Hardware included

28mm wood screws x 44

50mm wood screws x 29

E FC DBA

IHG

14mm wood screws x 160

metal sided pot drawers pairs x 1

metal sided drawers pairs x 2

90° angle bracket x 5

16mm wood screws x 12

adjustablelegs x 4

m3.5 14mm screws x 2

step 1Follow these instructions to build and attach your cabinet.

Things you need to know

Pencil

Cordless drill with:

• Number 2 screw tip

• 4mm drill bit

• Number 12 countersinking drill bit

Tape measure

Wall fixing(If necessary)

Adjustable square

65mm wood screw

Clamps(quick release)

Safety gear

Spirit level (900mm recommended)

p. 1Ver. 9W-70121

• Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back option make sure you pack out the back of your cabinet before screwing into the wall.

• All cabinets will need to be attached to the wall using a minimum of 8 gauge 65mm screws if you have a stud wall. If your wall is concrete, brick or another surface ask your hardware specialist for advice on the right fixing method.

• Make sure you leave plumbing and electrical work to qualified trades people. Never try this yourself.

• For extra strength use exterior woodworking glue when assembling cabinets.

• To help identify panels, counter sunk holes always face outwards.

• All holes that aren’t already pre-drilled should be drilled prior to screwing using a No 12 countersinking drill bit.

• Make sure you always use safety gear like a mask, ear muffs and glasses when using tools.

• If you have any questions, contact us on: Australia: 1800 666 078 Monday to Friday between 8:00am and 6:00pm AEST, New Zealand: 0800 522 663 Monday to Friday between 8:00am and 5:00pm NZST or email: [email protected].

600mm 3 drawer base cabinet

Page 2: kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back

Back bracket Completed View

H

1.

base panel

D

hard

ware

key

145mm

A

AA

1.

ste

p 1

p. 2Ver. 9W-70121

3.2.

assembling cabinet

5.4.

E

600mm 3 drawer base cabinet

50mm wood screws

28mm wood screws

A

metal sided drawers pairs

H

adjustablelegs

EB

14mm wood screws

D

Cabinet frame now complete R

6.

Pre-drilledholes

E

B

side panel

side panel

side panel

side panel

support rail

bottom panel

Set height of the adjustable legs to 145mm.

back panel

back panel

back panel

Note: The brackets are marked R & L for right and left.

Clip the back bracket onto the ends of both the left and right metal drawer sides.

Slot the metal drawer side onto the base panel, aligning with the pre-drilled holes as pictured above. A metal tab will push into the base panel, helping to hold it in place. Screw from underneath using the 14mm screws. Repeat for the other side.

assembling cutlery drawers attaching drawer base panel

2.

Page 3: kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back

hard

ware

key

Back bracket Completed View

back panel

3rd hole

3rd hole

D

D

base panel

D

Slot the metal drawer side onto the base panel, aligning with the pre-drilled holes as pictured above. A metal tab will push into the base panel, helping to hold it in place. Screw from underneath using the 14mm screws. Repeat for the other side.

back panel

Click !

ste

p 1

p. 3Ver. 9W-70121

600mm 3 drawer base cabinet

14mm wood screws

metal sided pot drawers pairs

D I

Fit the back panel into position, aligning the pre-drilled holes with the back bracket holes and screw into place using the 14mm screws.

attaching drawer back panel

attaching runners to the cabinet

4.3.

Using the top row of holes on the runners, screw the 3rd hole on the front set into the first pre-drilled hole on the cabinet. On the back set of holes screw the 3rd hole into the pre-drilled hole on the cabinet.

Repeat for the other side.

Note: Pull out the runner to gain better access to the holes. It is recommended to install extra screws into the runner for added strength.

Note: The brackets are marked R & L for right and left.

Clip the back bracket onto the ends of both the left and right metal drawer sides.

attaching drawer base panelassembling pot drawer

attaching drawer back panel attaching support rails

1.

3. 4.

2.

Fit the back panel into position, aligning the pre-drilled holes with the back bracket holes and screw into place using the 14mm screws.

Push the end of the support rail onto each side of the back bracket of the drawer until it clicks into place.

D

Page 4: kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back

hard

ware

key

B

When you need to add an end panel check out the end panel instructions for installation tips.

ste

p 1

p. 4Ver. 9W-70121

600mm 3 drawer base cabinet

28mm wood screws

B

The drawer front can be easily adjusted with the mechanisms on the sides of the drawer. Use the horizontal front adjustment to adjust left and right. Use the vertical front adjustment to adjust up and down. Once you are happy with the placement of the fronts place the cover plate over the mechanisms.

Note: It may be easier to get all drawer fronts aligned to your liking by starting with the bottom drawer front and working up.

If you want to remove your drawer front or the drawer from the runners, first remove the cover plates from the sides. Use the top screws moving upwards, to release the drawer front. The drawers can be easily detached from the runners by pushing up on the back clips on each side and lifting the drawer off the runners.

6.drawer front adjustment

5.drawer installation

7.

removing drawer front and drawer

Sit the drawer onto the runners and carefully slide the drawer back along the runners until they click in.

Note: When installing multiple metal sided drawers, start at the bottom and work up.

Check that all cabinets are level.Cabinet complete with drawers R

completed cabinet joining cabinets

1. 2.

horizontal

front

adjustment

cover plate

vertical front

adjustment

drawer front

release

cover plate

runner

release

Page 5: kaboodle kitchen - 600mm 3 drawer base cabinet · 2015-12-11 · • Base cabinets come with different positions for attaching your back panel. If you are choosing the rebated back

600mm 3 drawer base cabinet

stud

plaster board

rebated backs

step 1

step 2

step 3

step 4

Then follow the instructions to fit your doors and panels.

Finish off your Kaboodle Kitchen by installing your benchtop.

Next grab your parts and accessories instructions.

Your Kaboodle cabinet is now complete.

ste

p 1

p. 5Ver. 9W-70121

Caring for your kaboodle cabinets

Looking after your cabinets is really easy and with the right care and maintenance they will last you for many years. Just follow these simple steps and if you need any more information you can contact us: Australia: 1800 666 078 Monday to Friday between 8:00am and 6:00pm AEST. New Zealand: 0800 522 663 Monday to Friday between 8:00am and 5:00pm NZST or email: [email protected].

Clean your cabinets with an all purpose, non-abrasive cleaner with a damp sponge or cloth and make sure you never use saturated cloth, harsh chemicals or thinner based cleaners as these will damage the surface of the melamine. Likewise, never use products that will scratch the surface like steel wool or wire brushes and avoid sharp objects that will scratch, cut or gouge the melamine surface. If this happens the internal board will be exposed and may swell. Kaboodle cabinets are water resistant but not water proof so any spills should be attended to immediately.

Handy hint: if the melamine surface of your cabinet is damaged you can try and cover it with a furniture repair crayon but just remember that this won’t seal the board back to its original finish.

Caring for your kaboodle parts and accessories: Hinges, runners and other parts and accessories should be kept dry at all times. To keep the mechanisms performing at their best, regularly wipe them with a dry cloth removing any dust and grime that maybuild up. In case of spills, clean immediately with a dry cloth. Do not use harsh abrasives.

We offer a dedicated customer service line for advice or any questions you may have on kaboodle products.

Call customer service on: Australia: 1800 666 078 Monday to Friday between 8.00am and 6.00pm AEST

New Zealand: 0800 522 663 Monday to Friday between 8.00am and 5.00pm NZST or email: [email protected]

Check that all cabinets are level, and screw into wall using the correct fixings.

fixing cabinets to wall

Caution: Please ensure all cabinets are screwed into your timber stud wall using a minimum of 65mm timber screws. If attaching to concrete, brick, steel or any other substrates seek advice from your hardware specialist.

1.

Base cabinets have been designed with the ability to assemble your back panel to create a 16mm rebate. The rebated panels can be trimmed down to accommodate uneven walls.

rebated backs

Note: The gap behind your cabinets needs to be packed out before screwing to the wall.