Who has the most followers - Rihanna Bieber GaGa Sting McCartney or Bieber
Justin Bieber Concert Microphone Printed Circuit Board ... · To reassemble your device, follow...
Transcript of Justin Bieber Concert Microphone Printed Circuit Board ... · To reassemble your device, follow...
Justin Bieber Concert Microphone PrintedCircuit Board (PCB) Replacement
If the device is still not producing sound after troubleshooting your Justin Bieber ConcertMicrophone with guides 1 through 3, the problem may be in the printed circuit board (PCB).
Written By: Mike Seyman
Justin Bieber Concert Microphone Printed Circuit Board (PCB) Replacement Draft: 2015-01-11Guide ID: 32172 -
This document was generated on 2019-09-18 05:43:21 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 6
INTRODUCTION
A printed circuit board (PCB) mechanically supports and electronically connects electroniccomponents using conductive tracks made of copper laminated onto a non-conductive plastic. ThePCB reduces the amount of wires in a device and inherently makes any device more reliable. Thestep by step instructions will describe how to troubleshoot your PCB.
TOOLS:Phillips #2 Screwdriver (1)Flathead Screwdriver (1)Soldering Iron (1)
Justin Bieber Concert Microphone Printed Circuit Board (PCB) Replacement Draft: 2015-01-11Guide ID: 32172 -
This document was generated on 2019-09-18 05:43:21 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 6
Step 1 — Removing back panel
Remove the back panel of the device by unscrewing the single #8 11.6 mm Flathead screw on theback of the device.
Step 2 — Removing batteries
Remove the 3 AAA batteries fromthe device.
Justin Bieber Concert Microphone Printed Circuit Board (PCB) Replacement Draft: 2015-01-11Guide ID: 32172 -
This document was generated on 2019-09-18 05:43:21 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 6
Step 3 — Removing back half of device
Unscrew the other 4, #8 11.6 mm Phillips Head screws to remove the entire back half of thedevice.
Pull apart the device once screws are loose, splitting the device in half.
Step 4 — Positioning device
Keeping all wires connected to theirattachments, place the front half ofthe device face down.
Justin Bieber Concert Microphone Printed Circuit Board (PCB) Replacement Draft: 2015-01-11Guide ID: 32172 -
This document was generated on 2019-09-18 05:43:21 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 6
Step 5 — Inspecting PCB
Inspect the printed circuit board forany breaks or cracks.
Step 6 — Removing PCB
Remove the 2, #8 11.7 mm Phillips Head screws as well as the 2, #8 7.5 mm screws on theprinted circuit board.
Justin Bieber Concert Microphone Printed Circuit Board (PCB) Replacement Draft: 2015-01-11Guide ID: 32172 -
This document was generated on 2019-09-18 05:43:21 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 6
To reassemble your device, follow these instructions in reverse order.
Step 7 — Replacing PCB
Disconnect all wires from the PCB
Remove the damaged PCB from the microphone
Place new PCB in the Justin Bieber Concert Microphone.
Connect all the wires to the new PCB using this soldering guide.
Justin Bieber Concert Microphone Printed Circuit Board (PCB) Replacement Draft: 2015-01-11Guide ID: 32172 -
This document was generated on 2019-09-18 05:43:21 AM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 6