JIS Piping Handbook

Contents Page

1. Classification 1 - 4

2. Piping System Abbreviation 7

3. Symbol 8- 24

4. Piping Drafting Symbol For Pipe & Pipe Fittings 25 - 26

5. Method For Identification Of Pipes And Its System 27

6. Installation Guidance 28 - 31

7. Pipe Insulation Standard 32 - 44

8. Pipe Expansion Loint Application Standard 45

9. Pipe 46 - 54

10. Flange 55 - 66

11. Sleeve/Socket/Union Joint 67 - 72

12. Elbow 73 - 77

13. Reducer 78 - 84

14. Tee Piece (Equal) 85 - 86

15. Tee Piece (Reducing) 87 -92

16. Expansion Joint 93 - 109

17. Penetration Piece 110 - 113

18. Pipe Bending Table & Calculation 114 - 124

19. Piping Table 125

20. Pipe Support And Pipe Band 126 - 139

21. Pad 140

22. Bolt & Nut Standard (Iso Thread) 141 - 143

23. Stud Bolt & Nut Standard (Iso Thread) 144 - 145

24. Bellmouth 146 - 148

25. Heating Coil Fabrication 149

26. Welding Method Of Slip-On Flange 150

27. Cut Hole Opening Standard 151

28. Limit Of Working Space For Outfitting In Engine Room 152 - 161

29. Standard Of Fitting Material 162 - 172

30. Tap Drills & Screw Thread 173 - 174

31. Standard Gauges Dimension 175 - 176

CLASSIFICATION SOCIETY REQUIREMENT

LRS

Administrator1

DNV Table A2 Minimum nominal wall thickness for steel pipes (except pipes covered by Load Line Regulations)

External diameter D, mm Pipes in general

3), 4), 5), 6), 7), 8)

Air, overflow and sounding pipes for structural tanks

1), 2), 3), 5), 8), 9)

Bilge, ballast and general seawater pipes

1), 3), 4), 5), 7), 8)

Bilge, air, overflow and sounding pipes through

ballast and fuel oil tanks, ballast lines through fuel oil tanks and fuel oil lines

through ballast tanks 1), 2), 3), 4), 5), 7), 8), 9)

10.2 - 12 1.6 13.5 17.2 1.8 20 2 21.3 - 25 2 3.2 26.9 33.7 2 3.2 38 44.5 2 4.5 3.6 6.3 48.3 2.3 4.5 3.6 6.3 51 63.5 2.3 4.5 4 6.3 70 2.6 4.5 4 6.3 76.1 82.5 2.6 4.5 4.5 6.3 8.9 - 108 2.9 4.5 4.5 7.1 114.3 - 127 3.2 4.5 4.5 8 133 139.7 3.6 4.5 4.5 8 152.4 168.3 4 4.5 4.5 8.8 177.8 4.5 5 5 8.8 193.7 4.5 5.4 5.4 8.8 219.1 4.5 5.9 5.9 8.8 244.5 - 273 5 6.3 6.3 8.8 298.5 - 368 5.6 6.3 6.3 8.8 406.4 - 457 6.3 6.3 6.3 8.8 1) For pipes efficiently protected against corrosion, the thickness may be reduced by an amount up to not more than 1 mm. 2) For sounding pipes, except those for cargo tanks with cargo having a flash point less than 60 C, the minimum wall thickness is intended

to apply to the part outside the tank. 3) For threaded pipes, where allowed, the minimum wall thickness is to be measured at the bottom of the thread. 4) The minimum wall thickness for bilge lines and ballast lines through deep tanks and for cargo line is subject to special consideration. 5) For larger diameters the minimum wall thickness is subject to special consideration. 6) The wall thickness of pipes within cargo oil and ballast tanks in systems for remote control of valves is not to be less than 4mm. 7) For inlets and sanitary discharges see Pt. 3 Ch. 2 Sec. 11 K 100. 8) For stainless steel pipes the minimum wall thickness will be specially considered, but it is in general not to be less than given in Table A1

for pipes of copper alloys. 9) For air pipes on exposed decks, see Pt 3 Ch. 2 Sec. 11 K 300.

Table A1 Minimum nominal wall thickness for pipes of copper and copper alloys and stainless steel.

Minimum nominal wall thickness, in

mm 1) External pipe diameter D, in mm Copper Copper alloy and stainless steel

D < 10 1 0.8 10 < D < 20 1.2 1

20 < D < 44.5 1.5 1.2 44.5 < D < 76.1 2 1.5 76.1 < D < 108 2.8 2 108 < D < 159 3 2.5 159 < D < 267 3.5 3 267 < D < 457 4 3.5

(470) 4 3.5 508 4.5 4

1) The wall thickness of pipes within cargo oil and ballast tanks in

systems for remote control of valves is not to be less than : 3 mm for Al-Brass. 2 mm for Cu-Ni and stainless steel.

Administrator2

Administrator

AdministratorTable D12.6(1) Minimum Thickness of Steel Pipes

AdministratorNK

Administrator3

Table D12.6(2) Minimum Thickness of Steel Pipes (1),(3) ( mm )

Notes:1 Where the thickness of pipes specified in standards does not comply with the minimum thickness in this

Table, the standard pipe may be used if the difference is 0.4 mm or less.2 Pipes are to be galvanized at least inside, except those fitted in the engine room.3 For pipes with a nominal diameter other than shown in this Table, their minimum diameter will be

considered by the Society in each case.

Administrator4

Table D12.7 Minimum Thickness of Copper and Copper Alloy Pipes( mm )Outside diameter Copper pipes Copper alloy pipes8-10 1 0.812-22 1.2 125-45 1.5 1.250-76.2 2 1.580-120 2.5 2130-190 3 2.5200-270 3.5 3280 4 3.5

Administrator5

PIPING SYSTEM ABBREVIATION ............................................................................................................................ 2

SYMBOL...................................................................................................................................................................... 3 STANDARD VALVES............................................................................................................................................. 3 SPECICAL VALVE ................................................................................................................................................. 4 REMOTE OPERATED VALVE............................................................................................................................... 4 REMOTE & AUTOMATIC CONTROL VALVES..................................................................................................... 5 TRAPS.................................................................................................................................................................... 6 STRAINERS ........................................................................................................................................................... 6 MOUTH PIECE....................................................................................................................................................... 6 AIR ESCAPE HEADS............................................................................................................................................. 6 FITTINGS................................................................................................................................................................ 7 GENERAL............................................................................................................................................................... 9 REMOTE OPERATED REACH ROD PIECE......................................................................................................... 9 PUMP MARKS...................................................................................................................................................... 10 PUMPS ................................................................................................................................................................. 10 SWITCHES........................................................................................................................................................... 10 INSTRUMENTATION ........................................................................................................................................... 10 FIRST CODE LETTER (MEASURING OBJECT)................................................................................................. 12 SUBSEQUENT CODE-LETTER (INSTRUMENT FUNCTION)............................................................................ 13 EXAMPLE............................................................................................................................................................. 13

SYMBOLS FOR PIPING ARRANGEMENT.............................................................................................................. 14 VALVE .................................................................................................................................................................. 14 STRAINERS & TRAPS ETC................................................................................................................................. 17 OTHER FITTINGS................................................................................................................................................ 18 PIPE AND PIPE JOINT ........................................................................................................................................ 19

PIPING DRAFTING SYMBOL FOR PIPE AND PIPE FITTING................................................................................ 20

METHOD FOR IDENTIFICATION OF PIPES AND ITS SYSTEM............................................................................ 22

INSTALLATION GUIDANCE .................................................................................................................................... 23 A) GUIDANCE OF SOUNDING PIPE FOR WATER TANK AND CARGO HOLD............................................ 23 B) GUIDANCE OF SOUNDING PIPE FOR OIL TANK ..................................................................................... 24 SOUNDING PIPE CONSTRUCTION........................................................................................................... 25 C) TYPICAL INSTALLATION OF AIR ESCAPE PIPE ...................................................................................... 26

Administrator

Administrator6

PIPING SYSTEM ABBREVIATION

NO SYSTEM ABBREVIATION

1 Ballast line WB/SW

2 Cooling sea water line CW/SW

3 Hydrant and wash deck line SW

4 Sanitary water supply SW

5 Feed water line FD

6 Drink water line FW

7 Hot water line for radiator HW

8 Hot water line HW/FH

9 Potable fresh water line FR

10 Cooling fresh water line (or Technical fresh water) FR

11 Bilge line BG/BL/BS

12 Soil drain line SL

13 Toilet scupper & basin drain SC

14 Scupper and drainage line SC

15 FO-line FO

16 Lubrication oil line LO

17 Air escape line AE

18 Sounding line SD

19 Voice tube line VC

20 Co2 fire extinguishing line Refer to legend in drawing

21 Compressed air line (working & starting air) CQ/CA

22 Control air for remote control V/V CA

23 Exhaust gas line GE

24 Steam line AS/AS-SUP

25 Steam exhaust line DR/EX/AS-RET

26 Tank heating line & drain line AS

27 Hydraulic line for wt. door HYD

28 Hydraulic line for towing winch HYD

29 Hydraulic line for steering gear room HYD

30 Hydraulic line for deck machinery control HYD

31 Air foam piping AF

32 Oxygen & acetylene gas piping GL

33 Inert gas system exhaust gas EI

34 Gauge GP

Administrator7

SYMBOL

SYMBOL

ITEM

For as fitted plan For key plan NAME REMARKS

Valve (globe & angle) Flange

Screw down check valve (globe & angle) Socket

Swing check

valve (with handle) Bat Welded

Lift check valve (globe & angle) Screw

Foot valve Union

Cock BITE union

3-way cock (T & L type)

Sluice valve

Sluice valve (water seal)

Hose valve (globe & angle)

Non return hose valve (globe & angle)

Butterfly valve

Storm valve (vertical & horizontal)

STAN

DAR

D V

ALVE

S

Valve manifold

Administrator8

SYMBOL

ITEM


Pressure gauge valve

Pressure gauge cock

Cock with locks

Self closing valve for F.O tank drain

Self closing valve for oil level gauge

Self closing valve for bilge

Self closing swing valve for sounding head Weight type

Self closing cock for sounding head Weight type

Self closing sluice valve for sounding head Spring type

Surface valve

Breather valve (globe & angle)

SPEC

ICAL

VAL

VE

Needle valve

Valve (globe & angle (by reach rod)

Screw down check valve (globe & angle) (by reach rod)

Sluice valve (by reach rod)

Butterfly valve (by reach rod)

Storm valve (vertical & horizontal) ( by reach rod)

REM

OTE

OPE

RAT

ED V

ALVE

Emergency closing valve (globe & angle)

Administrator9

SYMBOL IT

EM


Governor valve

Safety valve (globe & angle)

Relief valve (by reach rod)

Relief valve (with handle)

Press-vacuum relief valve (globe & angle)

Miniature direct control valve (with strainer)

Direct operated control valve Reducing valve

Direct operated control valve (with handle) included

Diaphragm control valve

Diaphragm control valve (with handle)

Diaphragm control valve (with positioner)

Level control valve

Level control valve (Hi-flo)

Level control valve (ball tap)

Miniature magnet valve (3-way)

Magnet valve (globe, angle)

Quick close magnet valve

Hydraulic cylinder valve (globe, angle, sluice & butterfly) Hydraulic local operation

Air cylinder valve (globe, angle, sluice & butterfly)

Electric motor valve (globe, angle, sluice & butterfly)

REM

OTE

& A

UTO

MAT

IC C

ON

TRO

L VA

LVES

Air motor valve (globe, angle, sluice & butterfly)

Administrator10

SYMBOL IT

EM


Syphon breaker

Steam trap with strainer (impulse type)

Steam trap with strainer (thermostatic type)

Steam trap with strainer (backer type)

TRAP

S

Vacuum trap (float type)

Bilge hat

Strainer (single)

Strainer (duplex)

Mud box

Rose box

STR

AIN

ERS

Bell mouth

Mouth piece without cover

Mouth piece with cover With receiver

MO

UTH

PIE

CE

Mouth piece with whistle

Air escape pipe bend head (globe & angle) (by reach rod)

Air escape gooseneck head float check type without gauge wire net

Air escape gooseneck head float check type with gauge wire net

Air escape bonnet head without gauze wire net

AIR

ESC

APE

HEA

DS

Air escape bonnet head with gauze wire net

With filling cap Screw type Flange type

Administrator11

SYMBOL IT

EM


Expansion joint (dresser type)

Expansion joint (sleeve type)

Expansion joint (rubber type)

Expansion joint (stainless bellow type)

Flexible tube (flange type)

Flexible tube (screw type)

EXPA

NSI

ON

JO

INTS

Off-set bend

Sounding cap

Sounding deck piece

Hose flange

Blank flange Normal open

Spectacle flange Normalshut

Orifice

Boss

Bottom plug (P1-type)

Bottom plug (P2-type)

Drain plug with chain

Drain hole

Anchoring piece

Seel pot

FITT

ING

S

Reducer

Administrator12

SYMBOL IT

EM


Tee piece

Penetrating piece

Temperature sensitive piece

Phone

Special flange

Whistle

Hopper

Hopper with sight glass

Scupper piece with rose plate Withcoaming

Water sealed scupper piece with rose plate

Scupper piece without rose plate Sleeve type

Scupper for upper deck

Drain & air separator

Oil catcher for exh. gas steam line

Air chamber & float chamber

FI

TTIN

GS

Scupper piece with water tight

Administrator13

SYMBOL IT

EM


Pipe line (cross)

Pipe line (connecting)

Waste pipe

Sprinkling pipe

Rubber lining line

F.O. pipe with tracer

Capillary tube

Control air line

Hydraulic line

Electric wire

Overboard discharge

GEN

ERAL

U seal

REM

OTE

OPE

RAT

ED R

EAC

H

RO

D P

IEC

E

Administrator14

SYMBOL IT

EM


Remote start & stop

Remote start

Remote stop

Automatic start & stop

Automatic start

Automatic stop

Automatic change

PUM

P M

ARKS

Hand pump

Priming pump

Ejector

Eductor PU

MPS

Hydraulic oil pump

Thermal switch

Limit switch

Level switch

SWIT

CH

ES

Pressure switch

Pressure gauge Locate amount

Vacuum gauge

Compound gauge

Differential pressure gauge

INST

RU

MEN

TATI

ON

Dial gauge

Administrator15

SYMBOL IT

EM


Manometer Locate amount

Thermometer pocket

Thermometer

Resistance bulb & thermometer sensor

Float gauge

Float level gauge

Glass level gauge

Flow meter

Sight glass

Ships draft gauge

Flat glass oil level gauge

Salinity cell

Electric type pressure indicator

Air purge set

Signal transmitter With code-letter when necessary

Local mounted instrument

Centralized panel mounted instrument

Monitor or data logger point

With code-letter indicated in next page

Auto manual selector

Relay

INST

RU

MEN

TATI

ON

Administrator16

SYMBOL IT

EM


A Composition

Co2 Particular composition (carbon dioxide)

O2 Particular composition (oxygen)

CL Particular composition (salinity)

PH Particular composition (hydroneum ion

D Density

F(Fr) Flow (Flow rate)

L Level

M Humidity

P Pressure

Pd Pressure differential

Q Heat calorie

S Speed

T Temperature

V Viscosity

W Weight

FIR

ST C

OD

E LE

TTER

(MEA

SUR

ING

OBJ

ECT)

X Other variation

Administrator17

SYMBOL IT

EM


I Indication

R Recorder

C Controller

S Counter

A(WITH H OR L) Alarm (high or low)

C/R Control console

B/G Boiler gauge board

E/R Main engine gauge board

SUBS

EQU

ENT

CO

DE-

LETT

ER (I

NST

RU

MEN

T FU

NC

TIO

N)

W/H Wheel house

1) Lettering order

as follows :

I or R-C-S-A

2) In case of recorder monitor & logger letter I not written

Control panel pressure indicator (pneumatic transmitted)

Temperature controller

High temperature alarm

Level recording controller with high & low alarm

EXAM

PLE

Pressure transitter (pneumatic) for A.C.C.

D1Pd

TC

HTA

MLLRCH

P TO ACC

Administrator18

SYMBOLS FOR PIPING ARRANGEMENT

VALVE

SYMBOLS TYPE

PLAN VIEW ELEVATION SECTION VIEW REMARK

Globe valve Direction of flow to be shown if necessary

Angle valve

NOTES: 1) size of

to be shown on respective plan and side view are taken from handle of valve size of whichever greater

Globe non-return valve

Angle non-return valve

Sluice valve Opening indicator are to be shown in principal

Gear control sluice valve

On plan and on section view show such indicator

2) when there is arrangement difficulty of sluice valve on plan and side view, a sketch of the valve should be included in

Gear control globe valve

Gear control angle valve

Globe hose valve

Angle hose valve

Globe non-return hose valve

Angle non-return hose valve

3) HANDLE BELOW and OPENING FRONT, BACK are to be shown when necessary

Remote control globe valve

Remote control angle valve

Remote control globe non-return valve

Remote control angle non-return valve

Administrator19

SYMBOLS FOR PIPING ARRANGEMENT..CONT

VALVE Notes:

SYMBOLS TYPE


Emergency closing valve

Bilge line closing valve

Screw globe valve

Screw angle valve

Lifting non-return globe valve

Lifting non-return angle valve

Lifting non-return standing valve Foot valve

Swing non-return valve

Safety valve globe type

Same as relief valve

Safety valve angle type

Same as relief valve

Safety valve (with handle)

Same to relief valve

Direct operated control valve (with handle)

To be drawn positioner and handle

Air operated control valve (with handle)

Same as above

Magnet valve

3-way control valve

Flow direction to be indicated

2-way cock

Administrator20


VALVE Notes:

SYMBOLS TYPE


3-way cock

Test valve (self closing valve for F.O. drain tank)

Butterfly valve

Storm valve

Electric motor operated globe valve

Electric motor operated sluice valve

Reach rod To be drawn reach rod and valve number

Globe

Breather valve

Angle

135

M

MM

M

M M

(T TYPE)

(L TYPE)

Administrator21


STRAINERS & TRAPS ETC Notes:

SYMBOLS REMARK TYPE

PLAN VIEW ELEVATION SECTION VIEW

Eductor

Single strainer

Duplex strainer

Y-type strainer

Mud box

Rose box

Steam trap

Steam trap (with strainer, not by-pass)

Steam trap (with strainer)

In case of with by-pass type must be drawn sentence

Hand pump

Water cock

Swing type

BY - PASS

Administrator22

SYMBOLS FOR PIPING ARRANGEMENT..CONT OTHER FITTINGS Notes:

SYMBOLS TYPE


Scupper

Box-type scupper

Hopper

Hopper with sight glass

Bell mouth

Sight glass

Expansion joint Flow direction to be shown in accordance with maker drawing

Spectacle flange To be marked SHUT or OPEN

Orifice

Flow meter

Fix-type thermometer

Thermometer

Seat

Size of seat to be drawn

For example

O(S) O(S) O(S)

M - 20

Administrator23

SYMBOLS FOR PIPING ARRANGEMENT..CONT PIPE AND PIPE JOINT Notes:

SYMBOLS TYPE


Joining piece

Slot in welding type

Butt weld tee

Penetration piece

Penetrating sleeve

In case of butt joint

Deck orflat

In case ofpenetration

Jacket type sleeve

Both end fitSleeve

Both end free

Special flange

ONE END FIT

Administrator24

PIPING DRAFTING SYMBOL FOR PIPE AND PIPE FITTING Screw or socket weld Butt weld Flange joint Single line Double line Single line Double line Single line

Top view

Elevation view 90 Elbow

Bottom view

Top view

Elevation view 45 Elbow

Bottom view

Top view

Elevation view T Joint

Bottom view

Top view

Elevation view Y Joint

Bottom view

Administrator25

PIPING DRAFTING SYMBOL FOR PIPE AND PIPE FITTING..cont Screw or

socket weld Butt weld Flange joint Single line Double line Single line Double line Single line

Top view

Reducer

Elevation view

Slip on Weld neck Cap joint Ring type joint Male/female flange Blind flange

Single line Flange joint

Double line

Branch joint Butt joint

Cap

Threaded

union

Socket or butt weld

reducing tee

Saddle joint

Single line Flange joint

Double line

Administrator26

100SW-01-101

100CW-01-107

100SW-01-103

150SW-01-102

METHOD FOR IDENTIFICATIONOF PIPES AND ITS SYSTEM

(FOR K-PLAN)

SYSTEM NOS.

PIPING SYSTEM

PIPE NOM. DIA.

PIPE NOM. DIA.

PIPING SYSTEM

TO K-PLANSYSTEM REF.

MARKPIPE PIECE

150SW-102-01

100SW-103-01

100CW-107-01

100SW-101-01

METHOD FOR IDENTIFICATION OF PIPES AND ITS SYSTEM (FOR AS FITTED PLAN)

Administrator27

INSTALLATION GUIDANCE

A) GUIDANCE OF SOUNDING PIPE FOR WATER TANK AND CARGO HOLD (Except in engine room)

Administrator28

B) GUIDANCE OF SOUNDING PIPE FOR OIL TANK (Except in engine room)

40 Sounding Cap & 80 Sounding Pipe

Note :

1. Bending radius of sounding pipe to be not less than one(1) meter.

Deck

TANK TOP

4 x 10 Holes

100

25

143

For No.1 F.O.T.

N=4

2. 10 holes (pitch 100 and 300 mm)to be provided for sounding pipe

up to about 10M above bottom forF.O. tanks only.

100

100

300

300

300

TANK TOP

Bottom

For No.2 & 3 F.O.T.

Administrator29

SOUNDING PIPE CONSTRUCTION

2 OPENINGS 80 X 5R FOR WATER ETC4 OPENINGS 80 X 5R FOR FUEL OIL

3

14

& DIESELOL

1000

FLANGE

TANK BOTTOM

INNER BOTTOM PLATEVENT HOLES 4-10 mm

TO BE DRILLED

DIA. 40 FOR WATER & OTHERSDIA. 80 FOR F.O. & D.O

Administrator30

Upper Deck(Penetration Piece)

Superstructure Deck(Penetration Piece)

150

(LR

)

Deck H (m/m)

0.25L FWDUpper Deck

Other Deck 450

760

Deck

UpperDeck

Detail Detail

15

C) TYPICAL INSTALLATION OF AIR ESCAPE PIPE

NOTE: Inclination of air escape pipe to be not less than 30 degrees from the horizontal plane. MATERIAL IF GAUGE WIRE STAINLESS STEEL (SUS 314)

Administrator31

PIPE INSULATION STANDARD APPLICATION TABLE OF PIPING INSULATION TABLE 1

INSULATION MATERIAL COVER

PIPE LINE APPLIED PLACES Pipe

Flange, valve & etc

Pipe Flange, valve & etc

REMARKS

Weather parts

Only the parts of pipes having the possibility of contacting with human body

Rock wool -

F.R.P. (Fibreglass

reinforced plastic)

(polytight)

- FIG - 1

Pipe above 10 mm Rock wool Rock wool Glass cloth Glass cloth

FIG - 2 FIG - 5

Deck steam line, exhaust line and tank heat line Accommodation pump room ,

steering gear room & pipe passgae

All pipes Pipe dia 10 mm

and below Not to be insulated

Weather parts Not to be applied - - - - - Exhaust pipe for emergency fire pump engine Accommodation All including in steering gear room Rock wool Rock wool Glass cloth Glass cloth

FIG - 2 FIG - 5

Weather parts All pipes Rock wool - F.R.P. (Polytight) - FIG -1 Domestic steam and drain Accommodation All pipes Rock wool Rock wool Glass cloth (Note 1)

Glass cloth (Note 1)

FIG - 5 FIG - 2

Hot water Accommodation All pipes Rock wool Rock wool Canvas (Note 1 ) Canvas (Note 1 )

FIG 3 FIG 5

Weather parts Not to be applied - - - - - Tank cleaning pipe Accommodation &

pump room Delivery side of tank cleaning heater Rock wool - Canvas - FIG 3

Weather parts Not to be applied - - - - - Sea water service pipe, wash deck pipe and scupper pipe Accommodation

All pipes except vertical pipes inside lining (Note 2) Canvas Canvas

FIG 5 FIG 8

Weather parts Not to be applied - - - - - Fresh water pipe and drain pipe Accommodation All pipes except vertical pipes inside lining (Note 2) Canvas Canvas

FIG 5 FIG 8

Freon suction pipe from ref. chamber to compressor Freon pipe

(R 22) Accommodation Freon liquid pipe from expansion valve to ref. chamber

Polyurethan Polyurethan Canvas and seal paint Canvas and seal paint

FIG 6 FIG 7

All duct except below Glass wool - Canvas - Duct or air conditioning Accommodation Sanitary and commissary

space Polyurethan (Note 3) -

F.R.P. (Polytight) (Note 3)

-

FIG 10

All duct except below Glass wool - Canvas - Mech. Exhaust and supply duct for (galley, pantry)

Accommodation Sanitary and commissary space

Polyurethan (Note 3) -

F.R.P. (Polytight) (Note 3)

- FIG - 9

Inert gas pipe Weather part Only from funnel to gas cooler Rock wool - Glass cloth - FIG - 4

Freon pipe for fish and meat room

Lobby and vegtable room All pipes Polyurethan Polyurethan

F.R.P. (Polytight)

F.R.P. (Polytight)

FIG 6 FIG 7

Note 1 :- Polytight to be applied to the pipes above one (1) meter from floor which are led in wet space Note 2 :- PVC tubes not to be insulated Note 3 :- Duct in the ceiling and/or lining not to be insulated.

Administrator32

THICKNESS OF INSULATION TABLE 2

Insulation material Pipe dia. 15 25 40 50 65 80 100 125 150 200 250 300 350

155C and above 25 30 30 35 35 35 35 35 40 40 40 40 50

154C 101C 20 20 20 20 25 25 25 25 25 25 25 30 30 Rock wool moulding

100C 60 C 20 20 20 20 20 20 20 25 25 25 25 25 25

R-22 suction line from cooling coil to compressor 50

R-22 line from expansion valve to cooling coil 25

Polyurethane foam

Engine room, galley pantry and lavatories 25

Engine room, galley, pantry and lavatories 50

Glass wool Fan room and living quarter 25

Administrator33

IS INSULATING METHOD OF PIPING (FIG 1)

Application : a). According to the application table of piping insulation. b). To be applied to weather parts. Insulation Method

Mark Material Remarks Note

1 Moulded rock wool Specific gravity : 200 kg/m

0.8t Galv. Steel band and Pipe dia > 125 2

#18 Galv. Iron wire Pitch : 300 mm

Pipe dia < 100

3 Cellophane paper 0.02 mm thickness

4 Glass tape 2 loops

5 Polyester resins

F.R.P. (Polytight)

3. Thickness of insulation material according to the table of thickness of insulation 4. Note : Distance A to be enough for removing the coupling bolts.

5 4 3 2 1

A

Administrator34


1. Application : a). According to the application table of piping insulation. b). To be applied to un-weather parts. 2. Insulation Method





Pipe dia < 100

3 Glass cloth 0.02 mm thickness


3 32

1

A

Administrator35







Pipe dia < 100

3 #11 Canvas To be adhered

4 Paint Finished with 2 coats

To be applied except inside of lining

5 Glass cloth 0.5mm thickness


A

5 4or5

31

2

Administrator36




1 Glass cloth 0.5mm thickness


1 2

Administrator37


1. Application : Pipe fittings such as flange, valve, T-piece, socket, sleeve and support. 2. Insulation Method 3. Thickness of insulation material according to the table of thickness of insulation


1 Insulating material Moulded

2 Insulating material Moulded

3 Silicate cement Stuff into a crevice

Canvas (in case of F) Paste 4

Glass cloth (in case of A B C E)

0.8t Galv. Steel band (Pipe dia. > 125) 5

#18 Galv. Iron wire (Pipe dia < 100) SUS band to be applied on weather part (SUS 304, 0.4mm thick)

E) SOCKET & SLEEVE

3

14

MIN. 50

2

5

c) T-PIECE

A) FLANGE

1

4

1

2 3

4 2 3

5

5

DK. & BHD.

F) WATER & DRAIN PIPE

G) DECK & BHD.

TO ALLOW PIPES TO SLIDEMIN. 25 MM

50MIN

.

1

TO PIPE SUPPORT.PENETRATING PIECE IS SIMILAR

D) SUPPORT

B) VALVE

1

43

2

5

Administrator38


1. Application : a). According to the application table of piping insulation. b). To be applied to freon piping. 2. Insulation Method


1 Adhesive Form seal 30-45

2 Foam polyurethane Specific gravity : 0.03 g/cm

3 #18 Galv. Iron wire 3-Loops / 1-Ray (0.5mm t)

4 AL-Foil

5 Glass tape & glass cloth 2-Loops / 1-Ray (0.5 mm t)

6 Coating for use in Ref. Prov, chamber (1.0 kg/m) Elastonato T/# 9840

7 Foamed polyurethane Soft

6 Coating for use except above space 2 coat (1.3 kg/m/2-coats) Seal FAS

3. Thickness of insulation material according to the table of thickness of insulation 4. Note : In case of freon pipe for vegetable,, fish and meat room, being led in lobby, these pipes to be insulated with 25 mm thick foamed polyurethane and finished coat.

4

1

2

1

3

2

7

&5 6

3

6

Administrator39


1. Application : According to the application table. ( For support parts of insulation freon pipe). 2. Insulation Method


1 Adhesive Form seal 30-45

2

3 Hard foam polyurethane Specific gravity : 0.1 g/cm JIS A9512 No 1 & above

4 AL-Foil

5 Glass cloth 1-Ray

6 Coating 2 coat (1.3 kg/m/2-coats) Seal FAS

3. Thickness of insulation material according to the table of thickness of insulation

MATERIAL THICKNESS (=t) LINE

Pipe from outside wall on ref. provision chamber to compressor 50 mm Suction pipe Hard foamed

polyuerthane Pipe from exp. Valve or dryer panel to outside wall on ref. provision chamber 25 mm Liquid pipe

54

6&3 1

45 & 6

3

1

Administrator40


1. Application : a) According to the application table of piping insulation. b) To be applied to sweat insulation 2. Insulation Method


1 #11 Canvas To be adhered to pipe


1 2

Administrator41

IS INSULATING METHOD OF VENT DUCT (RECTANGULAR) (FIG 9)

1. Application : According to the application table of piping insulation. 2. Insulation Method


1 Glass wool Specific gravity : 0.05 g/cm

2 Adhesive

3 #11 Canvas


5 Foamed polyurethane Specific gravity : 0.03 g/cm

6 Cellophane paper Thickness: 0.02 mm

7 Glass tape 2 - Loops

8 Polyester resins F.R.P. Polytight


b.) To be applied to sanitary & commissary space.

2 5

2 1

6 7

3 4

8

a.) To be applied to enclosed part.

Administrator42

IS INSULATING METHOD OF VENT DUCT (SPIRAL) (FIG 10) 1. Application : According to the application table of piping insulation. 2. Insulation Method


1 Glass wool Specific gravity : 0.05 g/cm

0.8t Galv. Steel band & Pipe dia 125 2 #18 Galv. Iron wire Pitch : 300 mm Pipe dia 100

3 Adhesive Width : 50 mm

4 #11 Canvas


6 Foamed polyurethane Specific gravity : 0.03 g/cm

7 Cellophane paper Thickness: 0.02 mm

8 Glass tape 2 - Loops

9 Polyester resins F.R.P. Polytight


b.) To be applied to sanitary & commissary space.

6 3

& FLEXIBLE DUCTSPIRAL DUCT

1 2

72 8 9

3 4 5

a.) To be applied to enclosed parts.

Administrator43

Administrator

IS INSULATING METHOD OF PENETRATING PIECE FOR FIRE SAFETY MEASURE (FIG 11) 1. Application : To be applied to penetrating piece to the A-15, A-30 and A-60 class bulkhead and deck. 2. Insulation Method 3. Material


0.8t Galv. Steel band ( Dia > 125 ) Pipe dia 125 1

#18 Galv. Iron wire ( Dia < 100 )

Pipe dia 100

4. Note : Length L L > 1.5 D (Dia above 100 mm) L > 150 mm ( Dia 100 mm and under)

T : Thickness of insulation

T

TO THE BULKHEAD OR DECK

SAME AS INSULATION MATERIALT

L

1

PIPE OR DUCT

BULKHEAD OR DECKA-15, A-30 AND A-60 CLASS

D

Administrator44

PIPING EXPANSION JOINT APPLICATION STANDARD (HULL PART)

1. Type of expansion joint and application location

TYPE APPLICATION LOCATION TO BE APPLIED MAINLY FOR

Dresser type All type of pipe line below 16kg/cm. (except steam & condensate pipe, heating drain pipe and butterworth line.)

Cargo oil line, ballast line, pipe line running longitudinal direction on upper deck (cargo oil line, vent line, fuel oil line, compressor air line, water supply line, deck wash/fire line, foam fire fighting line, cable conduit pipe)

Sleeve type

For big expansion required line such as steam & condensate line, heating drain pipe and butterworth pipe.

Upper deck steam line, condensate line, heating drain line, butterworth line

Bend pipe type

To absorb the pipe expansion at the location where dresser type, sleeve type or bellow type expansion joint fitting is not used (mainly due to the piping arrangement). This type is widely used for small pipe below 25 nominal diameter.

All type of pipe line

Bellow type

Apply for the looation if bend pipe arrangement is impractical and the location required for normal inspection and is difficult to reach.

Deck machinery operation hydraulic oil line at hatch side. Fuel oil line and steamline inside pipe duct.

Remarks: Fire line for ship complied to B O T, fuel oil line inside pipe duct with DNV class are not allowed to used dresser type fitting. Generally sleeve type to be used.

2. Expansion installation number of expansion joint.

2.1 Dressor type expansion joint - For pipe nominal size below 300A

1 piece is required for pipe length within 24M

- For pipe nominal size above 350A 1 piece is required for pipe length with 12M

2.2 Sleeve type expansion joint

1 piece is required for pipe length within 24M

2.3 Bellow type expansion joint - For steam line, 1 piece is required for pipe length with 24M - For deck machinery operation hydraulic line, 1 piece is required for pipe length within 40M

3. Expansion absorbing rate for expansion joint fitting.

TYPE ABSORBING RATE REMARKS

Dressor type 10mm Extension absorbing rate base on set length Sleeve type 80 mm Contraction absorbing rate base on set length

40 mm Contraction absorbing rate base on set length

Bellow type 70 mm 4. Piping expansion rate

- Due to the deflection of the hull, the piping expansion rate will be 0.7mm per 1m length.

- Due to the change of the temperature, the expansion rate base 1C, will be 0.012mm pper 1m for steel pipe and about 0.017mm per 1m for copper pipe.

Administrator45

PIPE

JIS STANDARD STEEL PIPE

(1) Electric resistance welded steel pipe of group II and seamless carbon steel pipes of group I

Wall thickness (mm) and weight (kg/m)

Group II Group I Nominal diameter SGP Sch. 40 Sch 80 Sch. 40 Sch. 80 Sch. 120 Sch. 160

A B C SB SC SD SE

mm inch

Out Dia

(mm)

Thk Wt Thk Wt Thk Wt Thk Wt Thk Wt Thk Wt Thk Wt Thk Wt

6 1/8 10.5 2.0 0.419 1.7 0.369 2.4 0.479 1.7 0.369 2.4 0.479

8 13.8 2.3 0.652 2.2 0.629 3.0 0.799 2.2 0.629 3.0 0.799

10 3/8 17.3 2.3 0.851 2.3 0.851 3.2 1.11 2.3 0.851 3.2 1.11

15 1/2 21.7 2.8 1.31 2.8 1.31 3.7 1.64 2.8 1.31 3.7 1.64 4.7 1.97

20 3/4 27.2 2.8 1.68 2.9 1.74 3.9 2.24 2.9 1.74 3.9 2.24 5.5 2.94

25 1 34.0 3.2 2.43 3.4 2.57 4.5 3.27 3.4 2.57 4.5 3.27 6.4 4.36

32 1 1/4 42.7 3.5 3.38 3.6 3.47 4.9 4.57 3.6 3.47 4.9 4.57 6.4 5.73

40 1 1/2 48.6 3.5 3.89 3.7 4.10 5.1 5.47 3.7 4.10 5.1 5.47 7.1 7.27

50 2 60.5 3.8 5.31 3.9 5.44 5.5 7.46 3.9 5.44 5.5 7.46 8.7 11.1

65 2 1/2 76.3 4.2 7.47 5.2 9.12 7.0 12.0 5.2 9.12 7.0 12.0 9.5 15.8

80 3 89.1 4.2 8.79 5.5 11.3 7.6 15.3 5.5 11.3 7.6 15.3 11.1 21.4

90 3 1/2 101.6 4.2 10.1 5.7 13.5 8.1 18.7 5.7 13.5 8.1 18.7 12.7 27.8

100 4 114.3 4.5 12.2 6.0 16.0 8.6 22.4 6.0 16.0 8.6 22.4 11.1 28.2 13.5 33.6

125 5 139.8 4.5 15.0 6.6 21.7 9.5 30.5 6.6 21.7 9.5 30.5 12.7 39.8 15.9 48.6

150 6 165.2 5.0 19.8 7.1 27.7 11.0 41.8 7.1 27.7 11.0 41.8 14.3 53.2 18.2 66.0

200 8 216.3 5.8 30.1 8.2 42.1 12.7 63.8 8.2 42.1 12.7 63.8 18.2 88.9 23.0 110

250 10 267.4 6.6 42.4 9.3 59.2 15.1 93.9 9.3 59.2 15.1 93.9 21.4 130 28.6 168

300 12 318.5 6.9 53.0 10.3 78.3 17.4 129.0 10.3 78.3 17.4 129 25.4 184 33.3 234

350 14 355.6 7.9 67.7 11.1 94.3 19.0 158 11.1 94.3 19 158 27.8 225 35.7 282

400 16 406.4 7.9 77.6 12.7 123 21.4 203 12.7 123 21.4 203 30.9 286 40.5 365

450 18 457.2 7.9 87.5 14.3 156 23.8 254 14.3 156 23.8 254 34.9 363 45.2 459

500 20 508.0 7.9 97.4 15.1 184 26.2 311 15.1 184 26.2 311 38.1 441 50.0 565

SGP-E STPG-38E STPT-38S STPT-38S MATERIAL

SGP-B BUTT

WELDING PIPE ELECTRIC RESIST WELDED STEEL SEAMLESS CARBON STEEL

USED PIPE CARBON STEEL PIPE FOR ORDINARY PIPING CARBON STEEL PIPE FOR

PRESSURE SERVICE CARBON STEEL PIPE FOR HIGH TEMPERATURE

Administrator46

ASTM STANDARD STEEL PIPE ASA PIPE SCHEDULE

Wall = wall thickness in mm Wt = weights in kg/m

Nominal pipe size

Schedule 10

Schedule 20

Schedule 30 Standard

Schedule 40

Schedule 60

Extra strong

Schedule 80

Schedule 100

Schedule 120

Schedule 140

Schedule 160

Double extra strong

mm Inch

O.D mm Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt Wall Wt

6 1/8 10.3 1.7 0.357 1.7 0.357 2.4 0.470 2.4 0.470

8 13.7 2.2 0.625 2.2 0.625 3.0 0.804 3.0 0.804

10 3/8 17.1 2.3 0.848 2.3 0.848 3.2 1.10 3.2 1.10

15 21.3 2.8 1.26 2.8 1.26 3.7 1.62 3.7 1.62 4.8 1.95 7.5 2.54

20 26.7 2.9 1.68 2.9 1.68 3.9 2.19 3.9 2.19 5.6 2.89 7.8 3.63

25 1 33.4 3.4 2.50 3.4 2.50 4.5 3.23 4.5 3.23 6.4 4.23 9.1 5.45

32 1 42.2 3.6 3.38 3.6 3.38 4.9 4.46 4.9 4.46 6.4 5.60 9.7 7.75

40 1 48.3 3.7 4.05 3.7 4.05 5.1 5.40 5.1 5.40 7.1 7.23 10.2 9.54

50 2 60.3 3.9 5.43 3.9 5.43 5.5 7.47 5.5 7.47 8.7 11.1 11.1 13.4

65 2 73.0 5.2 8.62 5.2 8.62 7.0 11.4 7.0 11.4 9.5 14.9 14.0 20.4

80 3 88.9 5.5 11.3 5.5 11.3 7.6 15.3 7.6 15.3 11.1 21.3 15.2 27.7

90 3 101.6 5.7 13.6 5.7 13.6 8.1 18.6 8.1 18.6 16.2 34.0

100 4 114.3 6.0 16.1 6.0 16.1 8.6 22.3 8.6 22.3 11.1 28.3 13.5 33.5 17.1 41.1

125 5 141.3 6.6 21.8 6.6 21.8 9.5 30.9 9.5 30.9 12.7 40.2 15.9 49.0 19.0 57.4

150 6 168.3 7.1 28.2 7.1 28.2 11.0 42.5 11.0 42.5 14.3 54.2 18.3 67.5 21.9 79.1

200 8 219.1 6.4 33.3 7.0 36.7 8.2 42.5 8.2 42.5 10.3 53.1 12.7 64.6 12.7 64.6 15.1 75.8 18.3 90.7 20.6 101 23.0 112 22.2 108

250 10 273.0 6.4 41.7 7.8 50.9 9.3 60.2 9.3 60.2 12.7 81.5 12.7 81.5 15.1 95.8 18.3 115 21.4 133 25.4 156 28.6 172 25.4 155

300 12 323.9 6.4 49.7 8.4 65.1 9.5 73.8 10.3 79.7 14.3 109 12.7 97.4 17.4 132 21.4 160 25.4 187 28.6 208 33.3 239 25.4 187

350 14 355.6 6.4 54.6 7.9 68.1 9.5 81.2 9.5 81.2 11.1 94.3 15.1 126 12.7 107 19.0 158 23.8 195 27.8 224 31.8 253 35.7 281

400 16 406.4 6.4 62.6 7.9 77.9 9.5 93.1 9.5 93.1 12.7 123 16.7 180 12.7 123 21.4 203 26.2 245 30.9 286 36.5 333 40.5 365

450 18 457.2 6.4 70.5 7.9 87.8 11.1 122 9.5 105 14.3 156 19.0 206 12.7 139 23.8 254 29.4 310 34.9 363 39.7 408 45.2 459

500 20 506.0 6.4 78.5 9.5 117 12.7 155 9.5 117 15.1 183 20.6 248 12.7 155 26.2 311 32.5 381 38.1 441 44.4 508 50.0 564

550 22 558.8 6.4 86.4 9.5 129 12.7 171 9.5 129 22.2 294 12.7 171 28.6 373 34.9 451 41.3 526 47.8 600 54.0 671

600 24 609.6 6.4 94.7 9.5 141 14.3 210 9.5 141 17.4 255 24.6 355 12.7 187 30.9 441 38.9 547 48.0 639 52.4 719 59.5 807

650 26 660.4 7.9 128 128 203 9.5 153 12.7 203

700 28 711.2 7.9 138 138 219 15.9 272 9.5 165 12.7 219

750 30 762.0 7.9 147 147 234 15.9 292 9.5 176 12.7 234

800 32 812.8 7.9 157 157 250 15.9 312 9.5 186 12.7 250

850 34 863.8 7.9 167 167 266 15.9 332 9.5 200 12.7 266

900 36 914.4 7.9 177 177 282 15.9 361 9.5 212 12.7 282

Administrator47

API STANDARD STEEL PIPE STANDARD API-5L GRADE B

NOMINAL DIAMETER

mm INCH

OUTSIDE DIAMETER

(mm)

STD XS

XXS SCHEDULE THICKNESS (mm)

WEIGHT (kg/m)

STD 40 2.2 0.625 8 13.7

XS 80 3.0 0.804 STD 40 2.3 0.848

10 3/8 17.1 XS 80 3.2 1.10

STD 40 2.8 1.26 XS 80 3.7 1.62 - 160 4.8 1.95

15 21.3

XXS - 7.5 3.63 STD 40 2.9 1.68 XS 80 3.9 2.19 - 160 5.6 2.18

20 26.7

XXS - 7.8 3.64 STD 40 3.4 2.50 XS 80 4.5 3.23 - 160 6.4 4.23

25 1 33.4

XXS - 9.1 5.45 STD - 3.56 3.38 XS 80 4.8 4.46 32 1 42.4

XXS - 9.7 7.76 STD 40 3.7 4.05 XS 80 5.1 5.40 - 160 7.1 7.23

40 1 48.3

XXS - 10.16 9.55 STD 40 3.9 5.43 XS 80 5.5 7.47 - 160 8.7 11.1

50 2 60.3

XXS - 11.1 13.4 STD 40 5.2 8.62 XS 80 7.0 11.4 65 2 73

XXS - 14.0 20.4 STD 40 5.5 11.3 XS 80 7.6 15.2 - 160 11.1 21.3

80 3 88.9

XXS - 15.24 27.67 STD 40 5.7 13.5

90 3 101.6 XS 80 8.1 18.7

STD 40 6.0 16.1 XS 80 8.6 22.3 - 160 13.5 33.53

100 4 114.3

XXS - 17.1 41.0 STD 40 6.6 21.8 XS 80 9.5 30.9 125 5 141.3

XXS - 19.05 57.42 STD 40 7.1 28.2 XS 80 11.0 42.5 - 120 14.3 54.2 - 160 18.3 67.5

150 6 168.3

XXS - 21.9 79.1

Administrator48

API STANDARD STEEL PIPEcont STANDARD API-5L GRADE B

NOMINAL DIAMETER

mm INCH

OUTSIDE DIAMETER

(mm)

STD XS

XXS SCHEDULE THICKNESS (mm)

WEIGHT (kg/m)

- 20 6.4 33.3 - 30 7.0 36.8

STD 40 8.2 42.5 XS 80 12.7 64.6 - 120 18.3 90.3

200 8 219.1

XXS - 22.2 108 - 30 7.8 51

STD 40 9.3 60.2 XS 60 12.7 81.5 - 80 15.1 95.8 - 120 21.4 133

250 10 273

- 160 28.6 172 - 20 6.4 49.7 - 30 8.4 65.1

STD - 9.5 73.8 - 40 10.3 79.7

XS - 12.7 97.4 - 60 14.3 109 - 80 17.5 132 - 100 21.4 160

300 12 323.9

XXS 120 25.4 187 - 10 6.4 54.7 - 20 7.9 68

STD 30 9.5 81.2 - 40 11.1 94.3

XS - 12.7 107 - 60 15.1 127 - 80 19.0 158 - 100 23.8 195

350 14 355.6

- 120 27.8 224 - 20 7.9 77.9 - 30 9.5 93.1

STD 40 12.7 123 - 60 16.7 160 - 100 26.2 245 - 120 31.0 286

400 16 406.4

- 140 36.5 333 STD 20 9.5 105 XS - 12.7 139 - 60 19.0 205

450 18 457.2

- 80 23.8 254 STD 20 9.5 117 XS 30 12.7 155 500 20 508

- 40 15.1 183 - 30 12.7 171

550 22 558.8 -

STD 20 9.5 141 600 24 609.6

XS - 12.7 187

Administrator49

COPPER PIPES

1. Scope

This standard covers copper pipe used for general piping. 2. Dimensions

WALL THICKNESS AND WEIGHT

U A U B U C NOMINAL

DIAMETER (mm)

OUTSIDE DIAMETER

(mm) THICKNESS

(A) (mm) WEIGHT

(kg/m) THICKNESS

(B) (mm) WEIGHT

(kg/m) THICKNESS ( C ) (mm)

WEIGHT (kg/m)

4 6 1.0 0.140 - - 1.2 0.161

6 10 1.0 0.251 - - 1.4 0.330

10 15 1.0 0.391 - - 1.6 0.559

15 20 1.6 0.822 1.6 0.822 - -

20 25 1.6 1.046 1.8 1.166 - -

25 30 1.6 1.269 1.8 1.418 - -

32 35 - - 2.3 2.10 - -

40 45 2.0 2.40 2.3 2.74 - -

50 55 2.0 2.96 2.5 3.67 - -

65 70 2.0 3.80 3.0 5.61 - -

80 85 2.5 5.76 3.5 7.97 - - 100 110 3.0 8.97 4.0 11.84 - - 125 140 3.0 11.48 5.0 18.85 - - 150 160 3.5 15.30 5.5 23.73 - - 200 210 4.0 23.01 7.0 39.69 - - 250 270 4.5 33.37 9.0 65.60 - - 300 320 5.0 43.99 10.0 86.58 - -

350 363.7 5.0 50.09 - - - -

NOTE: 1) Pipe outside diameter 270 mm and smaller shall conform to JIS H3603

2) Mark * not to be used except special cases 3) Mark not to be used except special cases

4) The above standard base on ISSO 0021000E

Administrator50

ALUMINIUM BRASS PIPE & TUBES

WALL THICKNESS AND WEIGHT NOMINAL DIAMETER L A L B L C

Mm INCH

OUTSIDE DIAMETER

THK. (mm) *

WEIGHT (kg/m) THK.

(mm) * WEIGHT

(kg/m THK. (mm) *

WEIGHT (kg/m

8 9.53 1.6 SWG 16 0.33

10 15.14 2.0 SWG 14 0.69

15 21.50 1.4 SWG 17 0.74 2.3 SWG 13 1.17

25 1 28.25 1.4 SWG 17 0.99 2.0 SWG 14 1.38 2.6 SWG 12 1.76

40 1 40.95 1.4 SWG 17 1.46 2.0 SWG 14 2.05 3.7 SWG 9 3.63

50 2 54.05 1.6 SWG 16 2.22 2.0 SWG 14 2.75 4.5 SWG 7 5.89

65 2 66.8 1.6 SWG 16 2.75 80 3 79.9 1.8 SWG 15 3.71 100 4 106.3 2.3 SWG 13 6.31 125 5 131.7 2.3 SWG 13 7.85 150 6 157.7 2.6 SWG 12 10.64 200 8 208.5 2.6 SWG 12 14.13 250 10 260.5 3.3 SWG 10 22.40 300 12 312.1 3.7 SWG 9 30.11 350 14 363.7 4.1 SWG 8 38.91 400 16 414.5 4.1 SWG 8 44.40 450 18 465.3 4.1 SWG 8 49.90 500 20 516.9 4.5 SWG 7 60.85 550 22 567.7 4.5 SWG 7 66.88 600 24 619.4 4.9 SWG 6 79.46 650 25 660.4 4.9 SWG 6 84.76 700 28 711.2 6.4 SWG 3 119.03 750 29 762.0 6.4 SWG 3 127.61 800 30 812.8 6.4 SWG 3 136.19 850 33 863.6 7.0 SWG 2 158.23 900 35 914.4 7.0 SWG 2 167.62 1000 40 1016.0 8.3 SWG 0 220.72 1100 43 1117.6 8.3 SWG 0 242.97 1200 47 1219.2 8.3 SWG 0 265.22 1350 53 1371.6 8.3 SWG 0 298.60 REMARK: 1) Mark * shows wire gauge corresponding to the thickness

2) Mark not to be used except special cases 3) The above standard base on ISSO-0022000C

Administrator51

DIN STANDARD COPPER PIPE Pipe seamless and seam welded Material CUN10FE1MN 90/10 copper-nickel-iron, or CUN30MN1FE 70/30 copper-nickel

OUTSIDE DIAMETER OF PIPE WALL THICKNESS S (mm)

NOMINAL (INCH)

ACTUAL (mm) (1) 2 3 4 5 6

THEOR. WEIGHT

(1) (kg/m)

SEAMLESS

8 0.8 1 1.5 0.16 1/8 10 0.8 1 1 0.20 12 0.8 1 1.5 0.25 14 1 2.5 0.36

3/8 16 1 1.5 3 0.42 20 1 1.5 2 4 0.53 25 1.5 2 4 0.99 1 30 1.5 2 2.5 5 1.20

1 38 1.5 2 3 6 1.55 1 44.5 1.5 2 2.5 1.81

2 57 1.5 2 2.5 3 2.33 2 76 2 2.5 - - 4 4.15

3 89 2 2.5 3 - 4 4.86 4 108 2.5 3 3.5 - 5 7.40 5 133 2.5 3 - - 5 6 9.16 6 159 2.5 3 3.5 - 6 8 11.00 7 194 2.5 3 3.5 4 6 8 13.43 8 219 3 3.5 4 5 8 10 18.12

10 267 3 4 - 6 8 10 22.24 12 324 4 4.5 5 35.94 14 368 4 4.5 5.5 40.89 16 419 4 4.5 6 52.13

SEAM WELDED

8 219 3 3.5 4 5 8 10 18.21 10 267 3 4 - 6 8 10 22.24 12 324 4 4.5 5 35.94 14 368 4 4.5 5.5 40.89 16 419 4 4.5 6 52.70 18 457 4 4.5 7 57.48 20 508 4.5 5 7.5 70.92 24 610 4.5 5.5 9 76.20 28 711 6 6.5 10 118.00 32 813 6 7 11 135.00 36 914 8 12 203.57 40 1016 8 8.5 13.5 225.00

Pipe in sizes and alloys other than the above and larger than 1016 mm are also available Selected sizes are in accordance with the pipe components as per DIN 86087 up to 86090

Administrator52

COPPER NICKEL PIPE AND TUBE (CNTF) 1. Scope

This standard cover copper nickel pipes and tubes for ship 2. Dimension

THICKNESS & WEIGHT NOMINAL DIAMETER

90/10 Cu-Ni

Mm INCH

OUTSIDE DIAMETER

(mm) THICKNESS (mm) * WEIGHT (kg/m)

15 21.5 1.4 SWG 17 0.79

25 1 28.2 1.4 SWG 17 1.05

40 1 40.9 1.4 SWG 17 1.55

50 2 54.1 1.6 SWG 16 2.36

65 2 66.8 1.6 SWG 16 2.93

80 3 79.9 1.8 SWG 15 3.95

100 4 106.3 2.3 SWG 13 6.72

125 5 131.7 2.3 SWG 13 8.36

150 6 157.7 2.6 SWG 12 11.33

200 8 208.5 2.6 SWG 12 15.04

250 10 260.5 3.3 SWG 10 23.84

300 12 312.1 3.7 SWG 9 32.05

350 14 363.7 4.1 SWG 8 41.41

400 16 414.5 4.1 SWG 8 47.26

450 18 465.3 4.1 SWG 8 53.11

500 20 516.9 4.5 SWG 7 64.76

550 22 567.7 4.5 SWG 7 71.18

600 24 619.4 4.9 SWG 6 84.57

650 25 660.4 4.9 SWG 6 90.21

700 28 711.2 6.4 SWG 3 126.69

750 29 762.0 6.4 SWG 3 135.82

800 30 812.8 6.4 SWG 3 144.95

850 33 863.6 7.0 SWG 2 168.41

900 35 914.4 7.0 SWG 2 178.40

1000 40 1016 8.3 SWG 0 234.91

1100 43 1117.6 8.3 SWG 0 258.59

1200 47 1219.2 8.3 SWG 0 282.28

1350 53 1371.6 8.3 SWG 0 317.80

NOTE: 1) The above standard base on ISSO-0023000C

2) * Mark shows wire gauge of equivalent thickness

Administrator53

SEAMLESS STEEL PRECISION TUBES DRAWN OR COLD ROLLED DIMENSIONS DIN 2391 NOMINAL DIMENSION 0.5 0.6 0.8 1 1.2 1.5 1.8 2 2.2 2.5 2.8 3 3.5 4 4.5 5 5.5 6 7 8 9 10 WALL THK.

S PERM. VAR 10% OF NOMINAL DIMENSION S

WALL THK.

S

OUTSIDE DIAMETER NOMINAL DIMENSION

PERM. VAR

INSIDE DIAMETER NOMINAL DIMENSION AND PERMISSIBLE VARIATION

OUT.DIA NOMINAL DIMENSION

4 3 0.3 2.8 0.30 2.4 0.30 2 0.30 4

5 4 0.3 3.8 0.30 3.4 0.30 3 0.30 5

6 5 0.25 4.8 0.25 4.4 0.25 4 0.25 3.6 0.30 3 0.30 6

(7) 6 0.20 5.8 0.20 5.4 0.20 5 0.20 4.6 0.30 4 0.30 (7)

8 7 0.20 6.8 0.20 6.4 0.20 6 0.20 5.6 0.30 5 0.30 4.4 0.35 4 0.35 3.6 0.40 3 0.40 8

(9) 8 0.15 7.8 0.15 7.4 0.15 7 0.20 6.6 0.25 6 0.25 5.4 0.35 5 0.35 4.6 0.40 4 0.40

The stepped lines indicate ratios of wall thickness/ outside diameter for 1/20, 1/40 and 1/60 as contained in DIN 2391 sheet 2

(9)

10

0.1

9 0.15 8.8 0.15 8.4 0.15 8 0.20 7.6 0.25 7 0.25 6.4 0.30 6 0.30 5.6 0.35 5 0.35 10

12 11 0.15 10.8 0.15 10.4 0.15 10 0.15 9.6 0.20 9 0.20 8.4 0.25 8 0.25 7.6 0.30 7 0.30 6.4 0.40 6 0.40 12

(13) 12 0.08 11.8 0.15 11.4 0.15 11 0.15 10.6 0.15 10 0.20 9.4 0.25 9 0.25 8.6 0.30 8 0.30 7.4 0.40 7 0.40 (13)

14 13 0.08 12.8 0.08 12.4 0.08 12 0.08 11.6 0.15 11 0.15 10.4 0.20 10 0.20 9.6 0.25 9 0.25 8.4 0.30 8 0.30 14

15 14 0.08 13.8 0.08 13.4 0.08 13 0.08 12.6 0.08 12 0.15 11.4 0.20 11 0.20 10.6 0.25 10 0.25 9.4 0.30 9 0.30 15

16 15 0.08 14.8 0.08 14.4 0.08 14 0.08 13.6 0.08 13 0.08 12.4 0.15 12 0.15 11.6 0.20 11 0.20 10.4 0.30 10 0.30 9 0.35 8 0.35 16

18 17 0.08 16.8 0.08 16.4 0.08 16 0.08 15.6 0.08 15 0.08 14.4 0.08 14 0.08 13.6 0.20 13 0.20 12.4 0.20 12 0.20 11 0.35 10 0.35 18

20 19 0.08 18.8 0.08 18.4 0.08 18 0.08 17.6 0.08 17 0.08 16.4 0.08 16 0.08 15.6 0.15 15 0.15 14.4 0.15 14 0.20 13 0.30 12 0.35 11 0.35 10 0.35 20

22 21 0.08 20.8 0.08 20.4 0.08 20 0.08 19.6 0.08 19 0.08 18.4 0.08 18 0.08 17.6 0.08 17 0.15 16.4 0.15 16 0.15 15 0.20 14 0.30 13 0.35 12 0.35 22

25 24 0.08 23.8 0.08 23.4 0.08 23 0.08 22.6 0.08 22 0.08 21.4 0.08 21 0.08 20.6 0.08 20 0.08 19.4 0.15 19 0.15 18 0.15 17 0.20 16 0.20 15 0.30 25

(26) 25 0.08 24.8 0.08 24.4 0.08 24 0.08 23.6 0.08 23 0.08 22.4 0.08 22 0.08 21.6 0.08 21 0.08 20.4 0.15 20 0.15 19 0.15 18 0.15 17 0.20 16 0.30 (26)

28 27 0.08 26.8 0.08 26.4 0.08 26 0.08 25.6 0.08 25 0.08 24.4 0.08 24 0.08 23.6 0.08 23 0.08 22.4 0.08 22 0.08 21 0.15 20 0.15 19 0.15 18 0.20 17 0.30 16 0.30 28

30

0.8

29 0.08 28.8 0.08 28.4 0.08 28 0.08 27.6 0.08 27 0.08 26.4 0.08 26 0.08 25.6 0.08 25 0.08 24.4 0.08 24 0.08 23 0.15 22 0.15 21 0.15 20 0.15 19 0.30 18 0.30 30

32 31 0.15 30.8 0.15 30.4 0.15 30 0.15 29.6 0.15 29 0.15 28.4 0.15 28 0.15 27.6 0.15 27 0.15 26.40.15 260.15 25 0.15 24 0.15 23 0.15 22 0.15 21 0.30 20 0.30 32

35 34 0.15 33.8 .15 33.4 0.15 33 0.15 32.6 0.15 32 0.15 31.4 0.15 31 0.15 30.6 0.15 30 0.15 29.4 0.15 29 0.15 28 0.15 27 0.15 26 0.15 25 0.15 24 0.20 23 0.20 21 0.20 35

38 37 0.15 36.8 0.15 36.4 0.15 36 0.15 35.6 0.15 35 0.15 34.4 0.15 34 0.15 33.6 0.15 33 0.15 32.4 0.15 32 0.15 31 0.15 30 0.15 29 0.15 28 0.15 27 0.15 26 0.15 24 0.20 22 0.25 38

40

0.15

39 0.15 38.8 0.15 38.4 0.15 38 0.15 37.6 0.15 37 0.15 36.4 0.15 36 0.15 35.6 0.15 35 0.15 34.4 0.15 34 0.15 33 0.15 32 0.15 31 0.15 30 0.15 29 0.15 28 0.15 26 0.20 24 0.25 40

42 40 0.20 39.6 0.20 39 0.20 38.4 0.20 38 0.20 37.6 0.20 37 0.20 36.4 0.20 36 0.20 35 0.20 34 0.20 33 0.20 32 0.20 31 0.20 30 0.20 28 0.20 26 0.20 42

45 43 0.20 42.6 0.20 42 0.20 41.4 0.20 41 0.20 40.6 0.20 40 0.20 39.4 0.20 39 0.20 38 0.20 37 0.20 36 0.20 35 0.20 34 0.20 33 0.20 31 0.20 29 0.20 45

48 46 0.20 45.6 0.20 45 0.20 44.40.20 44 0.20 43.6 0.20 43 0.20 42.4 0.20 42 0.20 41 0.20 40 0.20 39 0.20 38 0.20 37 0.20 36 0.20 34 0.20 32 0.20 48

50

0.20

48 0.20 47.6 0.20 47 0.20 46.4 0.20 46 0.20 45.6 0.20 45 0.20 44.4 0.20 44 0.20 43 0.20 42 0.20 41 0.20 40 0.20 39 0.20 38 0.20 36 0.20 34 0.20 50

(52) 50 0.25 49.6 0.20 49 0.25 48.4 0.25 48 0.25 47.6 0.25 47 0.25 46.4 0.25 46 0.25 45 0.25 44 0.25 43 0.25 42 0.25 41 0.30 40 0.20 38 0.25 36 0.25 34 0.25 32 0.25 (52)

55 53 0.25 52.6 0.25 52 0.25 51.4 0.25 51 0.25 50.6 0.25 50 0.25 49.4 0.25 49 0.25 48 0.25 47 0.25 46 0.25 45 0.25 44 0.25 43 0.25 41 0.25 39 0.25 37 0.25 35 0.25 55

60

0.25

58 0.25 57.6 0.25 57 0.25 56.4 0.25 56 0.25 55.6 0.25 55 0.25 54.4 0.25 54.0.25 53 0.25 52 0.25 51 0.25 50 0.25 49 0.25 48 0.25 46 0.25 44 0.25 42 0.25 40 0.25 60

63 61 0.30 60.6 0.30 60 0.30 59.4 0.30 59 0.30 58.6 0.30 58 0.30 57.4 0.30 57 0.30 56 0.30 55 0.30 54 0.30 53 0.30 52 0.30 51 0.25 49 0.30 47 0.30 45 0.30 43 0.30 63

(65) 63 0.30 62.6 0.30 62 0.30 61.4 0.30 61 0.30 60.6 0.30 60 0.30 59.4 0.30 59 0.30 58 0.30 57 0.30 56 0.30 55 0.30 54 0.30 53 0.30 51 0.30 49 0.30 47 0.30 45 0.30 (65)

70

0.30

68 0.30 67.6 0.30 67 0.30 66.4 0.30 66 0.30 65.6 0.30 65 0.30 64.4 0.30 64 0.30 63 0.30 62 0.30 61 0.30 60 0.30 59 0.30 58 0.30 56 0.30 54 0.30 52 0.30 50 0.30 70

(75) 73 0.35 72.6 0.35 72 0.35 71.4 0.35 71 0.35 70.6 0.35 70 0.35 69.4 0.35 69 0.35 68 0.35 67 0.35 66 0.35 65 0.35 64 0.35 63 0.35 61 0.35 59 0.35 57 0.35 55 0.35 (75)

80 0.35

78 0.35 77.6 0.35 77 0.35 76.4 0.35 76 0.35 75.6 0.35 75 0.35 74.4 0.35 74 0.35 73 0.35 72 0.35 71 0.35 70 0.35 69 0.35 68 0.35 66 0.35 64 0.35 62 0.35 60 0.35 80

(85) 82 0.40 81.4 0.40 81 0.40 80.6 0.40 80 0.40 79.4 0.40 79 0.40 78 0.40 77 0.40 76 0.40 75 0.40 74 0.40 73 0.40 71 0.40 69 0.40 67 0.40 65 0.40 (85)

90 0.40

87 0.40 86.4 0.40 86 0.40 85.6 0.40 85 0.40 84.4 0.40 84 0.40 83 0.40 82 0.40 81 0.40 80 0.40 79 0.40 78 0.40 76 0.40 74 0.40 72 0.40 70 0.40 90

(95) 91 0.45 90.6 0.45 90 0.45 89.4 0.45 89 0.45 88 0.45 87 0.45 86 0.45 85 0.45 84 0.45 83 0.45 81 0.45 79 0.45 77 0.45 75 0.45 (95)

100 0.45

96 0.45 95.6 0.45 95 0.45 94.4 0.45 94 0.45 93 0.45 92 0.45 91 0.45 90 0.45 89 0.45 88 0.45 86 0.45 84 0.45 82 0.45 80 0.45 100

110 1060.50 105.60.50 105 0.50 104.40.50 1040.50 103 0.50 102 0.50 101 0.50 100 0.50 99 0.50 98 0.50 96 0.50 94 0.50 92 0.50 90 0.50 110

120 0.50

1160.50 115.80.50 115 0.50 114.40.50 1140.50 113 0.50 112 0.50 111 0.50 110 0.50 109 0.50 108 0.50 106 0.50 104 0.50 1020.50 1000.50 120

Administrator54

FLANGE JIS STANDARD 5 kg/cm SLIP ON WEDLING STEEL PIPE FLANGE (JIS B 2221)

FLANGE JIS 5K

DIMENSION NOM. DIA.

OUT.DIA. do D t T a b r C NO. h THREAD L W1 W2 (kg)

10 17.3 17.8 75 9 - - - - 55 4 12 M10 35 5 2.5 0.27

15 21.7 22.2 80 9 - - - - 60 4 12 M10 35 5 3 0.30

20 27.2 27.7 85 10 - - - - 65 4 12 M10 35 5 3 0.37

25 34 34.5 95 10 - - - - 75 4 12 M10 35 5 3 0.45

32 42.7 43.2 115 12 - - - - 90 4 15 M12 40 6 3 0.78

40 48.6 49.1 120 12 - - - - 95 4 15 M12 40 6 3 0.83

50 60.5 61.1 130 14 - - - - 105 4 15 M12 45 6 3 1.07

65 76.3 77.1 155 14 - - - - 130 4 15 M12 45 6 4 1.49

80 89.1 90 180 14 - - - - 145 4 19 M16 50 6 4 1.99

(90) 101.6 102.6 190 14 - - - - 155 4 19 M16 50 6 4 2.09

100 114.3 115.4 200 16 - - - - 165 8 19 M16 55 7 4 2.39

125 139.8 141.2 235 16 - - - - 200 8 19 M16 55 7 4 3.23

150 165.2 166.6 265 18 - - - - 230 8 19 M16 60 7 5 4.41

(175) 190.7 192.1 300 18 - - - - 260 8 23 M20 60 7.5 5 5.51

200 216.3 218 320 20 - - - - 280 8 23 M20 65 8.5 6 6.33

(225) 241.8 243.7 345 20 - - - - 305 12 23 M20 65 9 6 6.64

250 267.4 269.5 385 22 - - - - 345 12 23 M20 70 10 6 9.45

300 318.5 321 430 22 - - - - 390 12 23 M20 70 10 6 10.3

350 355.6 358.1 480 24 - - - - 435 12 25 M22 75 12 7 14

400 406.4 409 540 24 - - - - 495 16 25 M22 75 13 7 16.9

450 457.2 460 605 24 40 495 500 5 555 16 25 M22 75 12 7 24.8

500 508 511 655 24 40 546 552 5 605 20 25 M22 75 12 7 26.9

550 558.8 562 720 26 42 597 603 5 665 20 27 M24 80 12 7 34.1

600 609.6 613 770 26 44 648 654 5 715 24 27 M24 80 12 7 37.5

650 660.4 664 825 26 48 702 708 5 770 24 27 M24 80 12 7 42.8

700 711.2 715 875 26 48 751 758 5 820 24 27 M24 80 12 7 45.4

750 762 766 945 28 52 802 810 5 880 24 33 M30 90 12 7 57.4

800 812.8 817 995 28 52 854 862 5 930 24 33 M30 90 13 8 60.8

(850) 863.6 868 1045 28 54 904 912 5 980 24 33 M30 90 13 8 63.5

900 914.4 919 1095 30 56 956 964 5 1030 24 33 M30 95 13 8 75.3

1000 1016 1021 1195 32 60 1058 1066 5 1130 28 33 M30 100 14 9 88.5

D

C

d

t

W1

W2

h

0 0d

C

D

h

T

a r

NOM.DIA 10 - 400 NOM.DIA 450 - 1000

b

W1

W2

t

Administrator55

JIS STANDARD 10 kg/cm SLIP ON WEDLING STEEL PIPE FLANGE (JIS B 2222)

FLANGE JIS 10K

DIMENSION NOM. DIA.


10 17.3 17.8 90 12 - - - - 65 4 15 M12 40 5 2.5 0.52

15 21.7 22.2 95 12 - - - - 70 4 15 M12 40 5 3 0.57

20 27.2 27.7 100 14 - - - - 75 4 15 M12 45 5 3 0.73

25 34 34.5 125 14 - - - - 90 4 19 M16 50 5 3 1.13

32 42.7 43.2 135 16 - - - - 100 4 19 M16 55 6 3 1.48

40 48.6 49.1 140 16 - - - - 105 4 19 M16 55 6 3 1.56

50 60.5 61.1 155 16 - - - - 120 4 19 M16 55 6 3 1.88

65 76.3 77.1 175 18 - - - - 140 4 19 M16 60 6.5 4 2.6

80 89.1 90 185 18 - - - - 150 8 19 M16 60 6.5 4 2.61

(90) 101.6 102.6 195 18 - - - - 160 8 19 M16 60 6.5 4 2.76

100 114.3 115.4 210 18 - - - - 175 8 19 M16 60 7 4 3.14

125 139.8 141.2 250 20 - - - - 210 8 23 M20 65 7.5 4 4.77

150 165.2 166.6 280 22 - - - - 240 8 23 M20 70 8 5 6.34

(175) 190.7 192.1 305 22 - - - - 265 12 23 M20 70 9 5 6.82

200 216.3 218 330 22 - - - - 290 12 23 M20 70 9 6 7.53

(225) 241.8 243.7 350 22 - - - - 310 12 23 M20 70 9 6 7.74

267.4 269.5 400 24 - - - - 355 12 25 M22 75 10 6 11.8 250

267.4 269.5 400 24 36 288 292 6 355 12 25 M22 75 10 6 12.7

318.5 321 445 26 - - - - 400 16 25 M22 80 10 6 13.6 300

318.5 321 445 24 38 340 346 6 400 16 25 M22 75 10 6 13.8

350 355.6 358.1 490 26 42 380 386 6 445 16 25 M22 80 12 7 18.2

400 406.4 409 560 28 44 436 442 6 510 16 27 M24 85 12 7 25.2

450 457.2 460 620 30 48 496 502 6 565 20 27 M24 90 14 8 33

500 508 511 675 30 48 548 554 6 620 20 27 M24 100 14 8 37.6

550 558.8 562 745 32 52 604 610 6 680 20 33 M30 100 15 9 49.7

600 609.6 613 795 32 52 656 662 6 730 24 33 M30 110 16 10 52.6

650 660.4 664 845 34 56 706 712 6 780 24 33 M30 110 16 10 60.6

700 711.2 715 905 34 58 762 770 6 840 24 33 M30 110 17 10 70.6

750 762 766 970 36 62 816 824 6 900 24 33 M30 110 18 11 85.8

800 812.8 817 1020 36 64 868 876 6 950 28 33 M30 110 19 12 91.2

(850) 863.6 868 1070 36 66 920 928 6 1000 28 33 M30 110 19 12 98.6

900 914.4 919 1120 38 70 971 979 6 1050 28 33 M30 110 22 14 109

1000 1016 1021 1235 40 74 1073 1081 6 1160 28 39 M36 120 22 14 133

DCd

t

W1

W2

h

0 0dCD

hT

a r

NOM.DIA 10 - 225 NOM.DIA 250 - 1000

b

W2

W1

t

Administrator56


FLANGE JIS 16K

NOMINAL DIAMETER 10 ~ 600

DIMENSION NOM. DIA.


10 17.3 17.8 90 12 16 26 28 4 65 4 15 M12 40 4 2.5 0.52

15 21.7 22.2 95 12 16 30 32 4 70 4 15 M12 40 4 3 0.58

20 27.2 27.7 100 14 20 38 42 4 75 4 15 M12 45 5 3 0.75

25 34 34.5 125 14 20 46 50 4 90 4 19 M16 50 6 3.5 1.16

32 42.7 43.2 135 16 22 56 60 5 100 4 19 M16 55 6.5 4 1.53

40 48.6 49.1 140 16 24 62 66 5 105 4 19 M16 55 6.5 4 1.64

50 60.5 61.1 155 16 24 76 80 5 120 8 19 M16 55 6.5 4 1.83

65 76.3 77.1 175 18 26 94 98 5 140 8 19 M16 60 6.5 4.5 2.58

80 89.1 90 200 18 28 108 112 6 160 8 23 M20 65 6.5 4.5 3.66

90 101.6 102.6 210 18 30 120 124 6 170 8 23 M20 65 6.5 4.5 3.95

100 114.3 115.4 225 18 34 134 138 6 185 8 23 M20 70 7 5 4.94

125 139.8 141.2 270 20 34 164 170 6 225 8 25 M22 70 8 5 7.00

150 165.2 166.6 305 22 38 196 202 6 260 12 25 M22 75 8 5.5 9.62

200 216.3 218 350 22 40 244 252 6 305 12 25 M22 80 9 6.5 12.1

250 267.4 269.5 430 24 44 304 312 6 380 12 27 M24 85 9 6.5 20.0

300 318.5 321 480 26 48 354 364 8 430 16 27 M24 90 11 6.5 24.4

350 355.6 358.1 540 26 52 398 408 8 480 16 33 M30 x3 105 12 8 35.0

400 406.4 409 605 28 60 446 456 10 540 16 33 M30x3 110 12 8 46.2

450 457.2 460 675 30 64 504 514 10 605 20 33 M30 x3 115 16 9 61.9

500 508 511 730 30 68 558 568 10 660 20 33 M30x3 120 16 10 73.25 550 558.8 562 795 32 70 612 622 10 720 20 39 M36 x3 130 18 11 88.1

600 609.6 613 845 32 74 666 676 10 770 24 39 M36x3 135 18 11 98.8

0W2

W1

dCD

h

T

a

r

b t

Administrator57


FLANGE JIS 16K

NOMINAL DIAMETER 650 ~ 1200

DIMENSION NOM. DIA.

OUT. DIA. do D t T a b r f g C No. h Thread L W1 W2 (kg)

650 660.4 664 895 48 77 704 726 10 5 770 820 24 39 M 36x3 140 18 12 101

700 711.2 715 960 50 80 754 776 10 5 820 875 24 42 M 39x3 150 18 12 120

750 762.0 766 1020 52 83 806 832 10 5 880 935 24 42 M 39x3 150 18 12 141

800 812.8 817 1085 54 86 865 885 10 5 930 990 24 48 M 45x3 160 22 16 161

850 863.6 868 1135 56 89 916 936 10 5 980 1040 24 48 M 45x3 170 22 16 177

900 914.4 919 1185 58 93 968 986 10 5 1030 1090 28 48 M 45x3 170 22 16 191

1000 1016.0 1021 1320 62 99 1070 1098 12 5 1140 1210 28 56 M 52x3 180 22 16 230

1100 1117.6 1123 1420 66 105 1180 1200 12 5 1240 1310 32 56 M 52x3 190 26 19 289

1200 1219.2 1225 1530 70 112 1282 1302 12 5 1350 1420 32 56 M 52x3 200 26 19 348

d

b

45

0

Administrator58

A S A STANDARD STEEL FLANGE SLIP ON 150 LBS

R.F = 1/16 = 1.6mm 150/300 LBS = 6.4mm 600 LBS

STANDARD : ANSI B 16.5 MATERIAL : ASTM-A 105 N

NOM. DIA. SCREWS

mm INCH D d1 d3 b g k h

NO. d2 M x L WEIGHT

(kg)

15 88.9 30.2 22.3 9.5 34.9 60.3 15.9 4 15.9 M 12 x 40 0.8

20 98.4 38.1 27.7 11.1 42.9 69.8 15.9 4 15.9 M 12 x 40 0.9

25 1 107.9 49.2 34.5 12.7 50.8 79.4 17.5 4 15.9 M 12 x 45 1

32 1 117.5 58.8 43.2 14.3 63.5 88.9 20.6 4 15.9 M 12 x 50 1.3

40 1 127 65.1 49.5 15.9 73.0 98.4 22.2 4 15.9 M 12 x 50 1.4

50 2 152.4 77.8 62 17.4 92.1 120.6 25.4 4 19 M 16 x 60 2.3

65 2 177.8 90.5 74.7 20.6 104.8 139.7 28.6 4 19 M 16 x 65 3.2

80 3 190.5 107.9 90.7 22.2 127.0 152.4 30.2 4 19 M 16 x 70 3.6

100 4 228.6 134.9 116.1 22.2 157.2 190.5 33.3 8 19 M 16 x 70 5.9

125 5 254 163.5 143.6 22.2 185.7 215.9 36.5 8 22.2 M 20 x 70 6.8

150 6 279.4 192.1 170.7 23.8 215.9 241.3 39.7 8 22.2 M 20 x 75 8.6

200 8 342.9 246.1 221.5 27.0 269.9 298.4 44.4 8 22.2 M 20 x 80 13.6

250 10 406.4 304.8 276.3 28.6 323.8 361.9 49.2 12 25.4 M 22 x 85 19.5

300 12 482.6 365.1 327.1 30.1 381.0 431.8 55.6 12 25.4 M 22 x 90 29.1

350 14 533.4 400 359.1 33.3 412.7 476.2 57.1 12 28.6 M 24 x 95 38.6

400 16 596.9 457.2 410.5 34.9 469.9 539.7 63.5 16 28.6 M 24 x 100 42.2

450 18 635 504.8 461.8 38.1 533.4 577.8 68.3 16 31.7 M 27 x 110 54.5

500 20 698.5 558.8 513.1 41.3 584.2 635.0 73.0 20 31.7 M 27 x 120 70

600 24 812.8 663.6 615.9 46.0 692.1 749.3 82.5 20 34.9 M 30 x 130 95

700 28 927.1 781.0 717.5 50.8 793.7 863.6 87.3 28 34.9 M 30 x 140 123

750 30 984.2 831.8 768.3 52.4 857.2 914.4 88.9 28 34.9 M 30 x 145 138

900 36 1168.4 966.8 920.7 58.7 1022.3 1085.8 161.9 32 41.3 M 36 x 160 211

d1

d3

b h

d2

D

k

g

Administrator59



NOM. DIA. SCREWS


NO. d2 M x L WEIGHT

(kg)

15 95.2 38.1 22.3 12.7 34.9 66.7 22.2 4 15.9 M 12 x 45 1.2

20 117.5 47.6 27.7 14.3 42.9 82.5 25.4 4 19 M 16 x 50 1.3

25 1 123.8 54 34.5 15.9 50.8 88.9 27 4 19 M 16 x 55 1.4

32 1 133.3 63.5 43.2 17.4 63.5 98.4 27 4 19 M 16 x 60 1.8

40 1 155.6 69.8 49.5 19.0 73 114.3 30.2 4 22.2 M 20 x 65 2.7

50 2 165.1 84.1 62 20.6 92.1 127 33.3 8 19 M 16 x 65 3.2

65 2 190.5 100 74.7 23.8 104.8 149.2 38.1 8 22.2 M 20 x 75 4.5

80 3 209.5 117.5 90.7 27.0 127 168.3 42.9 8 22.2 M 20 x 80 5.9

100 4 254 146 116.1 30.1 157.2 200 47.6 8 22.2 M 20 x 90 10

125 5 279.4 177.8 143.8 33.3 185.7 234.9 50.8 8 22.2 M 20 x 95 12.7

150 6 317.5 206.4 170.7 34.9 215.9 269.9 52.4 12 22.2 M 20 x 100 17.7

200 8 381 260.3 211.5 39.7 269.9 330.2 61.9 12 25.4 M 22 x 110 26.3

250 10 444.5 320.7 276.3 46.0 323.8 378.3 66.7 16 28.6 M 24 x 125 36.8

300 12 520.7 374.6 327.1 49.2 381 450.8 73 16 31.7 M 27 x 135 52

350 14 584.2 425.4 359.1 52.4 412.7 514.3 76.2 20 31.7 M 27 x 140 74

400 16 647.7 482.6 410.5 55.5 469.9 571.5 82.5 20 34.9 M 30 x 150 100

450 18 711.2 533.4 461.5 58.7 533.4 628.6 88.9 24 34.9 M 30 x 155 127

500 20 774.7 587.4 513.1 61.9 584.2 685.8 95.2 24 34.9 M 30 x 160 148

600 24 914.4 701.7 615.9 68.2 692.1 812.8 106.4 24 41.3 M 36 x 210 222

gkD

d2

hb

d3

d1

Administrator60


R.F = = 6.4 mm STANDARD : ANSI B 16.5

MATERIAL : ASTM-A 105 N

NOM. DIA. SCREWS


NO. d2 M x L WEIGHT

(kg)

15 95.2 38.1 22.3 14.3 34.9 66.7 28.6 4 15.9 M 12 x 55 1.3

20 117.5 47.6 27.7 15.9 42.9 82.5 31.8 4 19 M 16 x 65 1.4

25 1 123.8 54 34.5 17.5 50.8 88.9 33.4 4 19 M 16 x 70 1.8

32 1 133.3 63.5 43.2 20.6 63.5 98.4 35.0 4 19 M 16 x 75 2.7

40 1 155.6 69.8 49.5 22.2 73 114.3 38.1 4 22.2 M 20 x 80 3.2

50 2 165.1 84.1 62 25.4 92.1 127 42.9 8 19 M 16 x 85 4.1

65 2 190.5 100 74.7 28.6 104.8 149.2 47.7 8 22.2 M 20 x 95 5.9

80 3 209.5 117.5 90.7 31.7 127 168.3 52.4 8 22.2 M 20 x 100 7.3

100 4 273 152.4 116.1 38.1 157.2 215.9 60.4 8 25.4 M 22 x 115 16.8

150 6 355.6 222.2 170.7 47.6 215.9 292.1 73.1 12 28.6 M 24 x 135 36

200 8 419.1 273 221.5 55.6 269.9 349.2 82.6 12 31.7 M 27 x 155 52

250 10 508 342.9 276.3 63.5 323.8 431.8 92.1 16 34.9 M 30 x 175 80

300 12 558.8 400 327.1 66.7 381 488.9 98.5 20 34.9 M 36 x 180 98

400 16 685.8 495.3 410.5 76.2 469.9 603.2 112.8 20 41.3 M 36 x 205 166

450 18 743.0 546.1 461.8 82.6 533.4 654.1 117.3 20 44.5 M 39 x 220 173

500 20 812.8 609.6 513.1 88.9 584.2 723.9 127 24 44.5 M 39 x 235 220

600 24 939.8 717.6 616 101.6 692.2 838.2 139.7 24 50.8 M 45 x 265 312

gkD

d2

hb

d3

d1

Administrator61

A S A STANDARD STEEL FLANGE WELDING-NECK 150 LBS STD

STANDARD : ANSI B 16.5


NOM. DIA. SCREWS

Mm INCH D d1 d3 b g k h

NO. d2 M x L WEIGHT

(kg)

15 88.9 21.3 15.7 9.5 34.9 60.3 47.6 4 15.9 M 12 x 40 0.8

20 98.4 26.7 20.9 11.1 42.9 69.8 52.4 4 15.9 M 12 x 40 1

25 1 107.9 33.4 26.6 12.7 50.8 79.4 55.6 4 15.9 M 12 x 45 1.1

32 1 117.5 42.2 35 14.3 63.5 88.9 57.1 4 15.9 M 12 x 50 1.4

40 1 127 48.3 40.9 15.9 73 98.4 61.9 4 15.9 M 12 x 50 1.8

50 2 152.4 60.3 52.6 17.4 92.1 120.6 63.5 4 19 M 16 x 60 2.7

65 2 177.8 73.1 62.6 20.6 104.8 139.7 69.8 4 19 M 16 x 65 3.6

80 3 190.5 88.9 77.9 22.2 127 152.4 69.8 4 19 M 16 x 70 4.5

100 4 228.6 114.3 102.3 22.2 157.2 190.5 76.2 8 19 M 16 x 70 6.8

125 5 254 141.3 128.1 22.2 185.7 215.9 88.9 8 22.2 M 20 x 70 8.6

150 6 279.4 168.3 154.1 23.8 215.9 241.3 88.9 8 22.2 M 20 x 75 10.9

200 8 342.9 219.1 202.7 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7

250 10 406.4 273 254.4 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6

300 12 482.6 323.9 304.9 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3

350 14 533.4 355.6 336.6 33.3 412.7 476.2 127 12 28.6 M 24 x 95 46.3

400 16 569.9 406.4 387.4 34.9 469.9 539.7 127 16 28.6 M 24 x 100 57.7

450 18 635 457.2 438.2 38.1 533.4 577.8 139.7 16 31.7 M 27 x 110 63.6

500 20 698.5 508 489 41.3 584.2 635 144.5 20 31.7 M 27 x 120 77.2

600 24 812.8 609.6 590.6 46.0 692.1 749.3 152.4 20 34.9 M 30 x 130 118

750 30 984.2 762 743 52.4 857.2 914.4 130.2 28 34.9 M 30 x 145 153

900 36 1168.4 914.4 895.4 58.7 1022.3 1085.8 161.9 32 41.3 M 36 x 160 242

b

d3

d1

gkD

d2 h

Administrator62

A S A STANDARD STEEL FLANGE WELDING-NECK 150 LBS XS



NOM. DIA. SCREWS


NO. d2 M x L WEIGHT

(kg)

15 88.9 21.3 13.9 9.5 34.9 60.3 47.6 4 15.9 M 12 x 40 0.8

20 98.4 26.7 18.9 11.1 42.9 69.8 52.4 4 15.9 M 12 x 40 1

25 1 107.9 33.4 24.4 12.7 50.8 79.4 55.6 4 15.9 M 12 x 45 1.1

32 1 117.5 42.2 32.6 14.3 63.5 88.9 57.1 4 15.9 M 12 x 50 1.4

40 1 127 48.3 38.1 15.9 73 98.4 61.9 4 15.9 M 12 x 50 1.8

50 2 152.4 60.3 49.3 17.4 92.1 120.6 63.5 4 19 M 16 x 60 2.7

80 3 190.5 88.9 73.7 22.2 127 152.4 69.8 4 19 M 16 x 70 4.5

100 4 228.6 114.3 97.1 22.2 157.2 190.5 76.2 8 19 M 16 x 70 6.8

125 5 254 141.3 122.3 22.2 185.7 215.9 88.9 8 22.2 M 20 x 70 8.6

150 6 279.4 168.3 146.3 23.8 215.9 241.3 88.9 8 22.2 M 20 x 75 10.9

200 8 342.9 219.1 193.7 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7

250 10 406.4 273 247.6 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6

300 12 482.6 323.9 298.5 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3

350 14 533.4 355.6 330.2 33.3 412.7 476.2 127 12 28.6 M 24 x 95 46.3

400 16 569.9 406.4 381 34.9 469.9 539.7 127 16 28.6 M 24 x 100 57.7

450 18 635 457.2 431.8 38.1 533.4 577.8 139.7 16 31.7 M 27 x 110 63.6

500 20 698.5 508 482.6 41.3 584.2 635 144.5 20 31.7 M 27 x 120 77.2

600 24 812.8 609.6 584.2 46.0 692.1 749.3 152.4 20 34.9 M 30 x 130 118

b

d3

d1

gkD

d2 h

Administrator

Administrator63

A S A STANDARD STEEL FLANGE


MATERIAL : ASTM-A 105 N WELDING-NECK 150 LBS XXS

NOM. DIA. SCREWS


NO. d2 M x L WEIGHT

(kg)

15 88.9 21.3 6.3 11.2 35.1 60.5 47.8 4 15.7 M 12 x 40 0.48

20 98.4 26.7 11.1 12.7 42.9 69.9 52.3 4 15.7 M 12 x 45 0.71

25 1 107.9 33.4 15.2 12.7 50.8 79.4 55.6 4 15.9 M 12 x 45 1.1

32 1 117.5 42.2 22.8 15.7 63.5 88.9 57.2 4 15.7 M 12 x 50 1.33

40 1 127 48.3 27.9 17.5 73.2 98.6 62.0 4 15.7 M 12 x 55 1.72

50 2 152.4 60.3 38.2 17.4 92.1 120.6 63.5 4 19 M 16 x 60 2.7

80 3 190.5 88.9 58.5 23.9 127.0 152.4 69.6 4 19.1 M 16 x 70 4.92

100 4 228.6 114.3 80.1 23.9 157.2 190.5 76.2 8 19.1 M 16 x 70 6.84

150 6 279.4 168.3 124.5 25.4 215.9 241.3 88.9 8 22.4 M 20 x 80 10.6

WELDING-NECK 150 LBS Sched 20

200 8 342.9 219.1 206.4 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7

250 10 406.4 273 260.3 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6

300 12 482.6 323.9 311.2 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3


200 8 342.9 219.1 205.1 27.0 269.9 298.4 101.6 8 22.2 M 20 x 80 17.7

250 10 406.4 273 257.4 28.6 323.8 361.9 101.6 12 25.4 M 22 x 85 23.6

300 12 482.6 323.9 311.2 30.1 381 431.8 114.3 12 25.4 M 22 x 90 36.3


300 12 482.6 323.9 303.3 31.8 381 431.8 114.3 12 25.4 M 22 x 95 36.5

350 14 533.4 355.6 333.4 35.1 412.8 476.3 127.0 12 28.4 M 24 x 100 48.4


250 10 406.4 273 242.8 30.2 323.9 362.0 101.6 12 25.4 M 22 x 90 24.0

300 12 482.6 323.9 288.9 31.8 381.0 431.8 114.3 12 25.4 M 22 x 95 36.5

400 16 596.9 406.4 363.6 36.8 469.9 539.8 127 16 28.4 M 24 x 105 60.6

500 20 698.5 508 455.6 42.9 584.2 635.0 144.5 20 31.8 M 27 x 120 84.5

600 24 812.8 609.6 547.6 47.8 692.2 749.3 152.4 20 35.1 M 30 x 135 115.0

b

d3

d1

gkD

d2 h

Administrator64



WELDING-NECK 150 LBS Sched 160 NOM. DIA. SCREWS

Mm INCH D d1 d3 b g k H

NO. d2 M x L WEIGHT

(kg)

15 88.9 21.3 11.7 9.5 34.9 60.3 47.6 4 15.9 M 12 x 40 0.8

20 98.4 26.7 15.5 11.1 42.9 69.8 52.4 4 15.9 M 12 x 40 1

25 1 107.9 33.5 20.9 12.7 50.8 79.4 55.6 4 15.9 M 12 x 45 1.1

32 1 117.5 42.2 29.4 15.7 63.5 88.9 57.2 4 15.7 M 12 x 50 1.33

40 1 127 48.3 34.1 15.9 73 98.4 61.9 4 15.9 M 12 x 50 1.8

50 2 152.4 60.3 42.9 17.4 92.1 120.6 63.5 4 19 M 16 x 60 2.7

80 3 190.5 88.9 66.7 22.2 127 152.4 69.8 4 19 M 16 x 70 4.5

100 4 228.6 114.3 87.3 22.2 157.2 190.5 76.2 8 19 M 16 x 70 6.8

150 6 279.4 168.3 131.7 25.4 215.9 241.3 88.9 8 22.4 M 20 x 80 10.6

200 8 342.9 219.1 173.1 28.4 269.7 298.5 101.6 8 22.4 M 20 x 85 17.7

250 10 406.4 273 215.8 30.2 323.9 362 101.6 12 25.4 M 22 x 90 24.0

WELDING-NECK 300 LBS Std

15 95.2 21.3 15.7 12.7 34.9 66.7 52.4 4 15.9 M 12 x 45 0.75

20 117.5 26.7 20.9 14.3 42.9 82.5 57.1 4 19 M 16 x 50 1.26

25 1 123.8 33.4 26.6 15.9 50.8 88.9 61.9 4 19 M 16 x 55 1.52

32 1 133.3 42.2 35 17.4 63.5 98.4 65.1 4 19 M 16 x 60 2.03

40 1 155.6 48.3 40.9 19.0 73 114.3 68.3 4 22.2 M 20 x 65 2.89

50 2 165.1 60.3 52.5 20.6 92.1 127 69.8 8 19 M 16 x 65 3.4

65 2 190.5 73.1 62.6 23.8 104.8 149.2 76.2 8 22.2 M 20 x 75 5.17

80 3 209.5 88.9 77.9 27.0 127 168.3 79.4 8 22.2 M 20 x 80 6.93

100 4 254 114.3 102.3 30.1 157.2 200 85.7 8 22.2 M 20 x 90 12

125 5 279.4 141.3 128.1 33.3 185.7 234.9 98.4 8 22.2 M 20 x 95 15.1

150 6 317.5 168.3 154.1 34.9 215.9 269.9 98.4 12 22.2 M 20 x 100 19.1

200 8 381 219.1 202.7 39.7 269.9 330.2 111.1 12 25.4 M 22 x 110 29.9

250 10 444.5 273 254.4 46.0 323.8 387.3 117.5 16 28.6 M 24 x 125 42.7

300 12 520.7 323.9 304.9 49.2 381 450.8 130.2 16 31.7 M 27 x 135 61.8

350 14 584.2 355.6 336.6 52.4 412.7 514.3 142.9 20 31.7 M 27 x 140 85.8

400 16 647.7 406.4 387.4 55.5 469.9 571.5 146 20 34.9 M 30 x 150 106

450 18 711.2 457.2 438.2 58.7 533.4 628.6 158.7 24 34.9 M 30 x 155 131

500 20 774.7 508 489 61.9 584.2 685.8 161.9 24 34.9 M 30 x 160 158

600 24 914.4 609.6 590.6 68.2 692.1 812.8 168.3 24 41.3 M 36 x 210 230

b

d3

d1

gkD

d2 h

Administrator65



WELDING-NECK 150 LBS Sched 160 NOM. DIA. SCREWS


NO. d2 M x L WEIGHT

(kg)

200 8 381 219.1 205 39.7 269.9 330.2 111.1 12 25.4 M 22 x 110 30.5

250 10 444.5 273 257 46.0 323.9 387.3 117.5 16 28.4 M 24 x 125 42.7

300 12 520.7 323.9 307.1 49.2 381 450.8 130.2 16 31.7 M 27 x 135 62.5

WELDING-NECK 300 LBS Sched 40 300 12 520.7 323.9 303.3 50.8 381 450.8 130.2 16 31.7 M 27 x 135 61.8

350 14 584.2 355.6 333.4 53.8 412.7 514.3 142.7 20 31.7 M 27 x 145 85.8

500 20 774.7 508 477.8 63.5 584.2 685.8 162.0 24 35.0 M 30 x 165 158

600 24 914.4 609.6 574.6 69.8 692.1 812.8 168.1 24 41.1 M 36 x 185 230

WELDING-NECK 300 LBS Sched 80 250 10 444.5 273 242.8 47.7 323.8 387.3 117.3 16 28.6 M 24 x 130 42.7

300 12 520.7 323.9 288.9 50.8 381 450.8 130.0 16 31.7 M 27 x 135 61.8

400 16 647.7 406.4 363.6 57.1 469.9 571.5 146 20 35 M 30 x 150 106

WELDING-NECK 300 LBS Sched 160 15 95.2 21.3 11.7 12.7 34.9 66.7 52.4 4 15.9 M 12 x 45 1

20 117.5 26.7 15.5 14.3 42.9 82.5 57.1 4 19 M 16 x 50 1.40

25 1 123.8 33.4 20.9 15.9 50.8 88.9 61.9 4 19 M 16 x 55 1.8

40 1 155.6 48.3 34.1 19.0 73 114.3 68.3 4 22.2 M 20 x 65 3.6

50 2 165.1 60.3 42.9 20.6 92.1 127 69.8 8 19 M 16 x 65 4.1

80 3 209.5 88.9 66.7 27.0 127 168.3 79.4 8 22.2 M 20 x 80 6.8

100 4 254 114.3 87.3 30.1 157.2 200 85.7 8 22.2 M 20 x 90 11.3

150 6 317.5 168.3 131.7 36.5 215.9 269.9 98.4 12 22.3 M 20 x 100 19.1

200 8 381 219.1 173.1 41.1 269.9 330.2 111.1 12 25.4 M 22 x 110 29.9

b

d3

d1

gkD

d2 h

Administrator66

SLEEVE/SOCKET/UNION JOINT SLEEVE TYPE JOINTS FOR STEEL PIPE

1. SCOPE: THIS STANDARD COVER SLEEVE TYPE JOINTS USED FOR GROUP II AND III PIPES 2. CONSTRUCTION, SHAPE AND DIMENSION TYPE S1 FOR JOINTS

DIMENSION WEIGHT (KG) REFERENCE NOM. DIA. API PIPE OUT.DIA

D d T L S1 2C W

10 17.2 27.2 19.4 3.9 30 0.067 2.1 3

15 21.3 34.0 24.0 5.0 40 0.143 2.3 3

20 26.7 38.1 29.1 4.5 40 0.149 1.9 3

25 33.4 45.0 36.0 4.5 40 0.179 2.0 4

32 42.2 55.0 45.0 5.0 50 0.309 2.3 4

40 48.3 63.5 51.5 6.0 50 0.426 2.9 5

50 60.3 76.3 62.3 7.0 50 0.598 1.8 6

65 73.0 96.0 78.0 9.0 60 1.17 1.7 6

80 88.9 110.0 91.0 9.5 70 1.68 1.9 7

100 114.3 139.8 117.8 11.0 75 2.61 3.5 8

125 141.3 165.2 143.2 11.0 80 3.34 3.4 9

150 168.3 190.7 168.7 11.0 100 4.88 3.5 9

200 219.1 247.3 221.9 12.7 110 7.33 2.8 11

250 273.0 304.1 276.1 14.0 120 11.79 3.0 11

300 323.8 352.8 326.8 13.0 130 13.94 3.0 12

350 355.6 384.6 358.6 13.0 130 15.49 3.0 12

400 406.4 435.4 409.4 13.

JIS Piping Handbook

Documents

Transcript of JIS Piping Handbook