Jib Crane

1377 Kimberly Dr., Neenah, WI 54956 (920)-722-0101 FAX (920)-725-1394

www.contrx.com

JIB CRANES GANTRY CRANES HOISTS & TROLLEYS BRIDGE CRANES SPREADER BEAMS PALLET LIFTERS FORKLIFT JIBS END TRUCKS11-19-02

FESTOON SYSTEMS, CRANE RAILS, CRANE CONTROLS, CRANE REPAIR & REBUILDING, MACHINING SERVICE

CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Fax

www.contrx.com

PRODUCT WARRANTY1. CONTRX Industries warrants products it manufactures against defects in materials and workmanship for a period of one year from date of receipt by the purchaser or his customer, or one year from time of completion of initial field installation if installed by CONTRX. CONTRX agrees to furnish the same or substantially similar replacement part (new or repaired) free of charge, F.O.B. site, providing the buyer gives immediate written notice of alleged defects and, if requested by CONTRX, returns the defective parts to our factory, freight collect, for our inspection and examination. 2. This warranty applies only to CONTRX equipment or materials which, after our inspection is determined to be defective either in material supplied or workmanship performed by CONTRX. Where equipment is furnished by CONTRX but not of its manufacture, CONTRXS liability is limited to such adjustment as the actual manufacturer makes to CONTRX. 3. CONTRX will not be liable for the cost of repairs, alterations, or replacements or any expense connected therewith made or incurred by the purchaser or his agents or employees, except upon written authority from the CONTRX office. 4. This warranty is personal to purchaser only and applies only to equipment the purchaser has properly operated and maintained in accordance with CONTRXS written instructions. 5. CONTRX assumes no liability for any consequential damages suffered through the use or loss of use of its equipment. 6. This constitutes CONTRXS sole warranty with respect to the equipment and material manufactured by itself. CONTRX makes no other warranty of any kind whatsoever, expressed or implied, and all implied warranties of merchantability and fitness for a particular purpose which exceed the aforementioned obligation are hereby disclaimed by CONTRX Industries.

MEMO TO DISTRIBUTORS CONCERNING LOSS AND DAMAGE CLAIMSFORM: CX11491 All merchandise is sold F.O.B. Contrx Factory, Neenah, WI. Title to the merchandise is transferred to the Distributor at the time the Carrier accepts the shipment. Any claims for loss, damage, or tracers for lost items in transit MUST BE FILED BY THE DISTRIBUTOR WITH THE CARRIER. Suitable copies of Bill of Lading will be furnished upon request if the Distributor has occasion to file a claim with the carrier. There are three types of claims that occur on shipments to customers. 1. 2. 3. Loss or short on delivery. Visible damage at time of delivery. Concealed damage noted after delivery.

There are three steps to take before signing a carrier delivery receipt. 1. 2. 3. Count the number of pieces and compare against count on the freight bill. Visually inspect each piece for damage. Read the labels and packing slips to be sure the freight belongs to you.

LOSS OR SHORT ON DELIVERY 1. 2. If the shipment is not received within ten working days after the known ship date, contact CONTRX Customer Service for the shipping information necessary for you to file a tracer. If a shipment is delivered short and the shortage is not delivered within 48 hours, contact CONTRX for the shipping information so you can file a tracer.

VISIBLE DAMAGE AT TIME OF DELIVERY 1 2. 3. 4. DO NOT REFUSE THE SHIPMENT or return damaged merchandise to CONTRX without authorization. The customer should immediately inspect the damage with the driver. The specific damage should be noted on both the customers copy and the carrier copy of the freight bill. The driver should sign both copies. Set the damaged merchandise aside and contact the carrier for an inspection.

CONCEALED DAMAGE NOTED AFTER DELIVERY 1. 2. 3. 4. Concealed damage must be reported to the carrier as soon as possible. Call the Carrier for an inspection. Follow the same procedure as for visible damage at the time of delivery. Any freight transferred after delivery that may have concealed damage is not recoverable by the Carrier or CONTRX.

FILING THE CLAIM 1. There are four basic documents necessary to support your claim. a. Delivery receipt with noted exceptions. b. Inspection report from the carrier. c. Cost of parts to repair the damage. (Repair Invoice) d. CONTRX Invoice showing the cost of the product. There is a nine month statute from date of receipt for filing a loss or damage claim. CONTRX Customer Service Department will provide any information or assistance to help resolve a loss or damage claim you have filed.

2. 3.

EFFECTIVE OCT. 2003

CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Fax

www.contrx.com

TERMS OF SALE

TERMS OF BILLING:

NET 30 DAYS TO APPROVED ACCOUNTS 1 1/2% Interest Charged on Past Due over 39 days from date on Invoice.

FREIGHT TERMS:

All Products Shipped Freight Collect or Prepaid-3rd Party Billing.

All shipments are made F.O.B Neenah, Wisconsin. When the shipment leaves our dock it becomes the property of the Distributor. Any claims for damage or shortages must be made by the Distributor. (SEE FORM CX11491) RETURNS: 20% restocking charge on all returns. Returns must be shipped freight Prepaid. Specially fabricated orders are not returnable.

SPECIALS:

CONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com

HEAVY DUTY JIB CRANES - 360 ROTATION FLOOR MOUNTEDOptional factory installed bottom entry electrical collector brings power in through the column assembly.

"A" SERIES

Beam Assembly Optional motorized boom rotation Column Assembly Head Assembly

Bolt-type base plate (Standard)

Foundation mount base (Optional) Optional top entry electrical collector can be attached to most 360 revolving jib cranes. No special parts needed. Sleeve mount base (Optional)

SELF-SUPPORTING FLOOR CRANES NEED MINIMUM HEAD ROOM.Contrx "A"- jibs are ruggedly constructed for industrial use and years of trouble-free service. Complete boom assembly is supported by an adjustable column roller assembly to permit field adjustment and insure even pressure of rollers on pipe. The boom is constructed using an I shaped rolled steel beam. The head assembly has two heavy side plates with reinforcing steel to create a rigid pivoting connection between the beam assembly and the column assembly. Standard jibs up to 20' span and 20' height under boom. Contrx specializes in modifications and custom designs.

10-22-02

FLOOR MOUNTED 'A' SERIES JIB CRANE SPECIFICATIONSF A

FIELD MOUNT

BOOM ASSEMBLYD 2" FWB = 12' HT. LBS. MODEL 715 A1128 878 A11210 914 A11212 1137 A11214 1566 A11216 1616 A11218 1997 A11220 969 A2128 1006 A21210 1464 A21212 1665 A21214 1725 A21216 2229 A21218 2422 A21220 1362 A3128 1413 A31210 1697 A31212 2069 A31214 2467 A31216 2547 A31218 3002 A31220 1426 A4128 1545 A41210 2106 A41212 2182 A41214 2774 A41216 3456 A41218 3580 A41220 1961 A6128 2041 A61210 2857 A61212 3216 A61214 3968 A61216 4642 A61218 5231 A61220 4034 A10128 4170 A101210 4878 A101212 5234 A101214 5386 A101216 6401 A101218 7158 A101220 B = 14' HT. LBS. MODEL 760 A1148 934 A11410 970 A11412 1499 A11414 1665 A11416 1789 A11418 2106 A11420 1025 A2148 1426 A21410* 1563 A21412 1774 A21414 1834 A21416 2467 A21418 2547 A21420 1462 A3148 1586 A31410 1806 A31412 2307 A31414 2593 A31416 2742 A31418 3197 A31420 1535 A4148 1654 A41410 2231 A41412 2307 A41414 2969 A41416 3597 A41418 4337 A41420** 2086 A6148 2166 A61410 2998 A61412 3357 A61414 4176 A61416 4850 A61418 5482 A61420 4495 A10148 4631 A101410 5578 A101412 5933 A101414 6085 A101416 6716 A101418 7473 A101420

HEAD ASSEMBLY

COLUMN ASSEMBLY LOWER ROLLER ASSEMBLY

B

BASE4"

3/4 E

E

W

3/4" DIA. REINFORCING RODS 6" FROM TOP & BOTTOM APPROX. 12" ON CENTER BOTH WAYS

Jib Crane Accessories: - Anchor Bolt Kits - Tagline Kits - Templates (Paper & Plywood) - Hoists & Trolleys (Electric & Manual) - Motorized Rotation1-1/4" DIA. 6 PLACES60

CAP. (LBS.) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 3,000 3,000 3,000 3,000 3,000 3,000 3,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 6,000 6,000 6,000 6,000 6,000 6,000 6,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000

A 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20'

D 6" 8" 8" 8" 10" 10" 12-3/8" 8" 8" 10" 12-3/8" 12-3/8" 16" 16" 10" 10" 12-3/8" 16" 16" 16" 21" 10" 12-3/8" 16" 16" 21" 23-3/4" 23-3/4" 16" 16" 16" 21" 23-3/4" 23-7/8" 23-7/8" 21-1/8" 21-1/8" 21-1/8" 23-7/8" 23-7/8" 23-7/8" 24-1/2"

FW 3-3/8" 4" 4" 4" 4-5/8" 4-5/8" 6-1/2" 4" 4" 4-5/8" 6-1/2" 6-1/2" 7" 7" 4-5/8" 4-5/8" 6-1/2" 7" 7" 7" 6-1/2" 4-5/8" 6-1/2" 7" 7" 6-1/2" 7" 7" 7" 7" 7" 6-1/2" 7" 9" 9" 8-1/4" 8-1/4" 8-1/4" 9" 9" 9" 9"

DIMENSIONS E W F 3' 4' 10-1/4" 3' 4' 10-1/4" 3' 4' 10-1/4" 3' 5' 12-1/4" 3' 5' 12-3/8" 3' 5' 12-3/8" 3' 5' 17-3/8" 4' 5' 10-1/4" 4' 5' 10-1/4" * 4' 6' 12-3/8" 4' 6' 12-3/8" 4' 7' 12-3/8" 4' 7' 17-3/8" 4' 7' 17-3/8" 4' 6' 12-3/8" 4' 6' 12-3/8" 4' 6' 12-3/8" 4' 7' 17-3/8" 4' 7' 17-3/8" 4' 8' 17-3/8" 4' 8' 17-3/8" 4' 6' 12-3/8" 4' 6' 12-3/8" 4' 7' 17-3/8" 4' 7' 17-3/8" 4' 8' 17-3/8" 4' 8' 21-3/8" 4' 8' 21-3/8" ** 4' 7' 17-3/8" 4' 7' 17-3/8" 4' 7' 21-3/8" 4' 8' 21-3/8" 4' 8' 21-1/2" 4' 9' 21-1/2" 4' 9' 24-1/2" 4' 9' 21-1/2" 4' 9' 21-1/2" 4' 9' 24-1/2" 4' 9' 24-1/2" 4' 10' 24-1/2" 4' 10' 29-1/2" 4' 10' 29-1/2"

BD 24" 24" 24" 36" 36" 36" 36" 36" 36" 36" 36" 36" 42" 42" 36" 36" 42" 42" 48" 48" 48" 36" 36" 42" 42" 48" 48" 48" 42" 42" 48" 48" 48" 54" 54" 60" 60" 66" 66" 66" 72" 72"

B = 10' HT. BOLT BEAM BC HOLES TYPE LBS. MODEL 6 S 20" 670 A1108 20" 6 S 822 A11010 20" 6 S 858 A11012 12 S 1081 A11014 32" 12 S 1467 A11016 32" 12 S 1517 A11018 32" 12 W 32" 1888 A11020 12 S 913 A2108 32" 12 S 950 A21010 32" 12 S 1365 A21012 32" 12 W 32" 1502 A21014 12 W 32" 1615 A21016 12 W 38" 2120 A21018 12 W 38" 2200 A21020 12 S 1263 A3108 32" 12 S 1314 A31010 32" 12 W 38" 1588 A31012 12 W 38" 1960 A31014 12 W 44" 2342 A31016 12 W 44" 2422 A31018 44" 12 W 2877 A31020 12 S 1317 A4108 32" 12 W 32" 1435 A41010 12 W 38" 1980 A41012 12 W 38" 2057 A41014 44" 12 W 2649 A41016 12 W 44" 3315 A41018 12 W 44" 3439 A41020 12 W 38" 1836 A6108 12 W 38" 1916 A61010 12 W 44" 2716 A61012 44" 12 W 3075 A61014 12 W 44" 3759 A61016 12 W 50" 4434 A61018 12 W 50" 4980 A61020 56" 12 W 3826 A10108 56" 12 W 3962 A101010 12 W 60" 4627 A101012 12 W 60" 4983 A101014 12 W 60" 5135 A101016 12 W 66" 6086 A101018 12 W 66" 6843 A101020

"S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam. * Model A21410 has an 'F' dimension of 12-1/4". ** Model A41420 has an 'F' dimension of 21-1/2"BOLT CIRCLE DIAMETER (BC)30

BASE PLATE DIAMETER (BD)W

1-1/4" DIA. 12 PLACES

BASE DETAIL HOLES EQUALLY SPACED

W

1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com

05-20-09

FBOOM ASSEMBLY

ATROLLEY STOPS (FACTORY MOUNTED)

DTROLLEY STOPS (FIELD MOUNTED)

FW CAPACITY WEIGHT A B B6 HOLES 1-1/4" DIA. 30 BOLT CIRCLE DIAMETER

HEAD ASSEMBLY

LBS. LBS.

C

ROLLER ASSEMBLY

COLUMN ASSEMBLY

C D E

BC

4"FLOOR CONCRETE FOOTING

BASE DIAMETER

F W FW BC BD

BD

WBASE DETAIL

E

3/4 E

1" ANCHOR BOLTS REQ'D. REINFORCING RODS 3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.

W

NOTES

NOT DESIGNED FOR OUTDOOR USEDATE

1377 Kimberly Dr., Neenah, WI 54956www.contrx.com

NOT TO SCALE

SALES-A-6H 12-13-05WJ

FLOOR MOUNT 'A' JIB WITH 6-HOLE BASEDWG NO

FBOOM ASSEMBLY

ATROLLEY STOPS (FACTORY MOUNTED)

DTROLLEY STOPS (FIELD MOUNTED)

FW CAPACITY WEIGHT A B B12 HOLES 1-1/4" DIA. 30 BOLT CIRCLE DIAMETER

HEAD ASSEMBLY

LBS. LBS.

C

ROLLER ASSEMBLY

COLUMN ASSEMBLY

C D E

BC

4"FLOOR CONCRETE FOOTING

BASE DIAMETER

F W FW BC BD

BD

WBASE DETAIL

E

3/4 E

1" ANCHOR BOLTS REQ'D. REINFORCING RODS 3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.

W

NOTES

NOT DESIGNED FOR OUTDOOR USEDATE


NOT TO SCALE

SALES-A-12H 12-13-05WJ

FLOOR MOUNT 'A' JIB WITH 12-HOLE BASEDWG NO

Boom Assembly Trolley Stops (field drill boom) Beam Plate Boom Mounting Hardware Head Assembly

Trolley End Stops Endstop Mounting Hardware Boom Mounting Hardware (see Note 2) Main Bearing Cup (pressed in at factory) Boom Leveling Adjustment Nuts (8)

1377 Kimberly Drive Neenah, WI 54956-1642 Office (920) 722-0101 Fax (920) 725-1394 www.contrx.com

o Bo

en mL

gth

Main Bearing (see Note 1)

Roller Shaft (2) Lower Roller Assembly Lower Roller (2) Thrust Washer (4) The following models have (2): -4000# cap. with longer than 16'-0" boom-6000# cap. with longer than 10'-0" boom-10,000# cap. all boom lengthsNote 1: Complete bearing assembly factory installed in the Boom Assembly on the following models: -4000# cap. with longer than 16'-0" boom-6000# cap. with longer than 10'-0" boom-all 10,000# cap. A-jibsNote 2: Beveled washers are to be used on tapered flange beams only. Note 3: For orders with similar multiple cranes, look for markings on the inside of the beam plate and the matching face of the head assembly. This will insure the correct parts are matched up.

Upper Bearing Pin Column Assembly Column Gussets Jib Base Plate

Lock Pin (2) Anchor Bolt Hardware Concrete Footing and 'L' Anchor Bolts (by customer) Refer to: FLOOR MOUNT 'A' JIB drawing number ________________

'A' Jib Assembly Detail 8-16-02 Not to scaleDWG NO

A-1005-A

F4 RING BOTTOM ENTRY ELECTRICAL COLLECTOR

ATIGHT WIRE ASSY BOOM ASSEMBLY

DSPROCKET TROLLEY STOPS (FIELD MOUNTED) GEAR REDUCER CONTROL PANEL BRAKE MOTOR HEAD ASSEMBLY ROLLER ASSEMBLY ACCESS HOLE BASE PLATE COLUMN ASSEMBLY 4C/SO CORD (POWER) 6C/SO CORD (CONTROL) 4" DIA HOLE FOR POWER SUPPLY

FW

CAPACITY WEIGHT

LBS. LBS.

12 HOLES 1-1/4" DIA.

A B C D

BOLT CIRCLE DIAMETER BC

C

B

30

BASE PLATE DIAMETER BD

E F W FW BC BD SUPPLY VOLTAGE JIB ROTATION SPEED: 1/2 RPM CONTROL VOLTAGE: 115-1-60V1377 Kimberly Dr., Neenah, WI 54956

W BASE DETAIL NOTES NOT DESIGNED FOR OUTDOOR USE

POWER IN

4" FLOOR1" ANCHOR BOLTS REQ'D.

E

3/4EREINFORCING RODS 3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.DATE

www.contrx.com

NOT TO SCALE

SALES-A-MD-12H 12-13-05WJ

CONCRETE FOOTING

MOTORIZED FLOOR MOUNT 'A' JIB WITH 12-HOLE BASEDWG NO

W

F

ABOOM ASSEMBLY

DTROLLEY STOPS (FIELD MOUNTED) TROLLEY STOPS (FACTORY MOUNTED)

FW CAPACITY LBS. LBS.

HEAD ASSEMBLY

S CROLLER ASSEMBLY

WEIGHT A 7/8" DIA. HOLE (4) B C D E

BCOLUMN ASSEMBLY

BWBASE PLATE

F W FW S BW

SQUARE BASE PLATE DETAILFLOOR

E

REINFORCING RODS 3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.

12"

4' 0" W

CONCRETE FOOTING

NOTES


NOT DESIGNED FOR OUTDOOR USE

DATE

NOT TO SCALE

SALES-A-FM 12-13-05WJ

FOUNDATION MOUNT 'A' JIBDWG NO

F

A

BOOM ASSEMBLY

DTROLLEY STOPS (FIELD MOUNTED) TROLLEY STOPS (FACTORY MOUNTED)

FWINSTALLATION INSTRUCTIONS

HEAD ASSEMBLY

1. PREPARE FIRST POUR FOOTING WITH ANCHOR BOLTS SET AS SHOWN. 2. AFTER FOOTING HARDENS, INSTALL AND LEVEL SLEEVE. SECURE BASE TO PREVENT SHIFTING DURING SECOND POUR.

CAPACITY WEIGHT A B C D E F W FW COLUMN OD SLEEVE ID

LBS. LBS.

C

ROLLER ASSEMBLY

3. POSITION REBAR PATTERN APPROX. 6" FROM TOP AND BOTTOM OF SECOND POUR.

BCOLUMN ASSEMBLY

4. MAKE SECOND POUR FOUNDATION, TAKING CARE TO MAINTAIN SLEEVE IN A PLUMB POSITION. ALLOW CONCRETE TO HARDEN. 5. INSERT JIB COLUMN INTO SLEEVE AND MAKE SURE CENTERING PIN PASSES THROUGH HOLE IN CAP PLATE ON BOTTOM OF COLUMN. 6. PLUMB JIB COLUMN. BLOCKS OR WEDGES (NOT PROVIDED) MAY BE INSERTED BETWEEN SLEEVE AND COLUMN TO HELP MAINTAIN POSITION.

SLEEVE (INCLUDED) BASE PLATE

7. INSTALL JIB HEAD & BOOM SECTION ON COLUMN. ROTATE BOOM SLOWLY TO CHECK COLUMN PLUMBNESS. ADJUST BLOCKING AS REQUIRED. 8. WHEN POSITION OF COLUMN IS SATISFACTORY, INSTALL SPLIT COLLAR WITH FILLET WELDS TO BOTH COLUMN AND SLEEVE LIP ALL THE WAY AROUND.

FLOOR

E

REINFORCING RODS 3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS. CONCRETE FOOTING

NOTES NOT DESIGNED FOR OUTDOOR USE

12"

4' 0" W X 7/8" DIA. HOLE (4)

WELD WEDGE SLEEVE BASE PLATE SECOND POURDATE

JIB COLUMN SPLIT COLLAR CENTERING PIN SLEEVE FLOOR

X SBW


E

NOT TO SCALE

SALES-A-SM 12-13-05WJ

FIRST POUR

SBWSLEEVE BASE PLATE DETAIL12"

4' 0" W

CONCRETE FOOTING 3/4" 'L' ANCHORS (4)

SLEEVE MOUNT 'A' JIBDWG NO

CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Faxwww.contrx.com

INSTALLATION INSTRUCTIONSPILLAR BASE MOUNT JIB CRANEPLEASE READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY1. The jib crane is shipped in three sections: head assembly, mast assembly, and boom assembly. A box containing the top bearing and mounting hardware is also included. 2. The footing shown is the only method recommended by the manufacturer. An individual competent in related foundation design methods and familiar with the installation site should design any alternative method. 3. Use a minimum 5 bag mix for concrete. A 2500 PSF soil pressure is assumed. Prior to pouring, position the rebar and L shaped anchor bolts as shown. Anchor bolts are submerged 3/4 of footing depth. The anchor bolt material specification is A36. Rebar is located 6 inches from top and bottom of the footing. Be sure to allow for power conduit if feeding through the base of the jib. Position the anchor bolts according to the base plate bolt circle dimensions. (The anchor bolts can be purchased through your jib crane supplier.) 4. After the concrete hardens, make sure a flat, level surface exists for accepting the mast assembly. Machinery grout and jam nuts may be used to level the surface. Erect the mast on the prepared surface, taking care not to damage the anchor bolt threads while setting the base plate in position. Tighten double nuts onto the anchor bolts after insuring that the mast is plumb. 5. Mount the top pivot bearing cone over the pin on top of the mast assembly. If installing the bottom entry collector option, read the collector installation instructions at this time. Attach boom assembly to head assembly with the hardware provided. Set the boom and head assembly in place on the mast. Make sure the roller bearing on top of the mast is seated correctly into he bearing race on the boom assembly. 6. Adjust the lower roller assembly in the head section to bring the boom into horizontal. * 7. Grease upper bearing and 5 diameter lower rollers through zerk fitting provided. Re-lube as conditions require. The 3 diameter lower rollers are self-lubricating. ** 8. Rotate the boom assembly to check for free movement and proper bearing seating. 9. Install the trolley end stops on the boom. Attach other optional equipment according to directions provided with the equipment. * Note - Small jibs are not adjustable at the lower rollers and may be leveled by shimming between the boom and the head mounting plates. ** Note - Small jibs are not equipped with a zerk fitting and need to be greased at the top bearing prior to seating the boom and head assembly.

WARNING:

THIS EQUIPMENT IS NOT DESIGNED FOR AND SHOULD NOT BE USED FOR LIFTING, SUPPORTING, OR TRANSPORTING PEOPLE.

CONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.comBoom Assembly

MEDIUM DUTY JIB CRANES - 360 ROTATION FLOOR MOUNTED

"B" SERIES

Optional top entry electrical collector can be attached to most 360 revolving jib cranes. No special parts needed.

Power to Crane Accessories

Upper Pipe Assembly

Power In

Lower Thrust Roller (2) Column Assembly Contrx brand "B" series jib cranes are well engineered and constructed machines at economical prices. The upper pipe assembly is jig welded to assure accuracy. Two heavy duty lower thrust rollers with lubrication-free teflon bearings assure smooth operation as the boom rotates on a tapered roller bearing atop the column assembly. The steel base plate and the column pipe are welded together robotically to insure a square connection. Standard Features: Boom rotates 360 Rolled steel I-beam boom fits most standard hoist trolleys. Bolt-on trolley end-stops allow easy trolley installation. Safety yellow enamel primer and paint finish Mounting details provided with installation instructions Adjustable rollers on 2000 lb. capacity units allow for boom leveling. Options: Anchor bolt kits Base plate templates (paper or plywood) Hoists and trolleys Boom rotation stops Top entry electrical collectors Tagline festoon kits Contact us for special requests.

Base Plate

"L" Anchor Bolts (Sold Separately) Concrete Foundation (by others)

1-29-03

FLOOR MOUNTED 'B' SERIES JIB CRANE SPECIFICATIONSJib Crane Accessories: - Anchor Bolt Kits - Tagline Kits - Templates (paper & plywood) - Hoists & Trolleys (electric & manual)DIMENSIONS CAP. (LBS.) A D FW E W 3' 4' 3" 5" 6' 250 3' 4' 3" 5" 8' 250 3' 4' 3" 5" 10' 250 3' 4' 3" 5" 12' 250 6" 3 3/8" 3' 5' 14' 250 6" 3 3/8" 3' 5' 16' 250 3' 4' 3" 5" 6' 500 3' 4' 3" 5" 8' 500 3' 4' 3" 5" 10' 500 6" 3 3/8" 3' 4' 12' 500 3' 5' 4" 8" 14' 500 3' 5' 4" 8" 16' 500 3' 4' 3" 5" 6' 750 6" 3 3/8" 3' 4' 8' 750 6" 3 3/8" 3' 4' 10' 750 6" 3 3/8" 3' 4' 12' 750 3' 5' 4" 8" 14' 750 3' 5' 4" 8" 16' 750 6" 3 3/8" 3' 4' 6' 1000 6" 3 3/8" 3' 4' 8' 1000 3' 4' 4" 8" 1000 10' 3' 4' 4" 8" 1000 12' 3' 5' 4" 8" 1000 14' 1000 16' 10" 4 5/8" 3' 5' 4' 5' 4" 8" 6' 2000 4' 5' 4" 8" 8' 2000 4' 5' 4" 8" 2000 10' 2000 12' 10" 4 5/8" 4' 6' ** B286 Uses base plate model 26R6. F 4" 4" 4" 4" 4" 5" 5" 5" 5" 6 1/2" 6 1/2" 6 1/2" 6 1/2" 6 1/2" 6 1/2" 7 1/2" 7 1/2" 7 1/2" 6 1/2" 6 1/2" 7 1/2" 7 1/2" 7 1/2" 8 1/2" 8 1/2" 8 1/2" 8 1/2" 9 1/2" BASE PLATE MODEL 15S4 15S4 15S4 15S4 15S4 15S4 15S4 15S4 15S4 24R6 24R6 24R6 24R6 24R6 24R6 24R6 24R6 26R6 26R6 26R6 26R6 26R6 26R6 26R6 28R8 28R8 28R8 30R12 B = 8' HT. B = 10' HT. LBS. MODEL LBS. MODEL 338 B25106 309 B2586 358 B25108 329 B2588 349 B25810 378 B251010 369 B25812 398 B251012 425 B25814 454 B251014 499 B25816 537 B251016 396 B5106 358 B586 416 B5108 378 B588 436 B51010 398 B5810 599 B51012 554 B5812 710 B51014 665 B5814 747 B51016 702 B5816 508 B75106 463 B7586 549 B75108 504 B7588 529 B75810 574 B751010 707 B75812 763 B751012 818 B75814 874 B751014 866 B75816 922 B751016 535 B1106 490 B186 560 B1108 515 B188 812 B11010 756 B1810 849 B11012 793 B1812 904 B11014 848 B1814 1113 B11016 1046 B1816 745 B286 ** 832 B2106 869 B2108 802 B288 905 B21010 739 B2810 1143 B21012 1069 B2812 B = 12' HT. LBS. MODEL 368 B25126 388 B25128 408 B251210 428 B251212 484 B251214 575 B251216 434 B5126 454 B5128 474 B51210 644 B51212 755 B51214 792 B51216 553 B75126 594 B75128 619 B751210 819 B751212 931 B751214 978 B751216 580 B1126 605 B1128 868 B11210 905 B11212 960 B11214 1180 B11216 899 B2126 935 B2128 972 B21210 1216 B21212

F

A

D

UPPER PIPE LOWER ROLLERS COLUMN ASSEMBLY

BOOM ASSEMBLY15" 12" 15" 12" B

FW

15S4

24R6 BASE PLATE4"

BASE PLATE MODEL 15S4 24R6 26R6 28R8 30R12

BASE DIA. 24" 26" 28" 30"

BOLT NO. CIRCLE HOLES 4 20" 6 22" 6 24" 8 26" 12

HOLE DIA. 7/8" 1 1/4" 1 1/4" 1 1/4" 1 1/4"

BOLT DIA. 3/4" 1" 1" 1" 1"

26R6

28R8

30R12

E

3/4 E

REINFORCING RODS 5/8" DIA. TOP - 3/4" DIA. BOTTOM APPROX. 12" ON CENTER BOTH WAYSW


07-14-06

F

A D

UPPER PIPE

BOOM ASSEMBLY BASE PLATE MODEL 15S4 24R6 26R6 28R8 30R12B

FW

BASE DIA. 24" 26" 28" 30"

BOLT CIRCLE 20" 22" 24" 26"

LOWER ROLLERSC

NO. HOLES 4 6 6 8 12

HOLE DIA. 7/8" 1 1/4" 1 1/4" 1 1/4" 1 1/4"BOLT CIRCLE DIAMETER

BOLT DIA. 3/4" 1" 1" 1" 1"

CAPACITY WEIGHT A B

COLUMN ASSY.15" 12"

15" 12"

15S4

24R6

26R6

28R8

30R12

C D E

BASE PLATE4"

NOTES

BASE DIAMETER NOT DESIGNED FOR OUTDOOR USE

F W FW

E

3/4 E

REINFORCING RODS 5/8" DIA. TOP - 3/4" DIA. BOTTOM APPROX. 12" ON CENTER BOTH WAYSW CONCRETE FOOTING

1377 Kimberly Dr., Neenah, WI 54956www.contrx.comDATE

NOT TO SCALE

SALES-B 12-13-05WJ

FLOOR MOUNT 'B' JIBDWG NO

Trolley End Stops Boom Mounting Hardware Boom Assembly Main Bearing Cup (Pressed in at Factory) Main Bearing Cup (Pressed in at Factory) Upper Pipe Assembly Roller Shaft Lock Pin (2) Main Bearing Cone Upper Bearing Pin Jib Column Anchor Bolt Hardware Column Gussets Jib Base Plate Lower Roller (2) Thrust Washer (2) Leveling Screw (4) End Stop Mounting Hardware

1377 Kimberly Drive Neenah, WI 54956-1642 Office (920) 722-0101 Fax (920) 725-1394 www.contrx.como Bo

en mL

gth

Roller Shaft (2)

Lower Roller (2) Thrust Washer (2)

Adjustable Lower Roller Assembly Used on the following jibs: -All 1000# cap. with 16'-0" boom-All 2000# cap. B-jibs-

Concrete Footing and 'L' Anchor Bolts (By Customer) Refer to: FLOOR MOUNT 'B' JIB drawing number ___________________

Assembly Note: Center the lower rollers directly below the boom.

'B' Jib Assembly Detail 10-4-06 Not to scaleDWG NO

B-1005-B

PORTABLE JIB CRANECONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com

360 Boom Rotation

No concrete foundation or floor anchoring required Easily moved by fork truck for multiple uses Easy to store and transport Use not limited to ground floor applications Not limited to industrial use

This innovative design eliminates the need for costly site preparation. The portable jib crane comes with its own steel base. No traditional concrete footing is required. Eliminate conventional jib location restrictions while gaining true portability and versatility.8-20-02

PORTABLE JIB CRANE SPECIFICATIONS(WEIGHT IS FOR JIB CRANE ONLY)CAPACITY (LBS) DIMENSIONS A 6'-0" 8'-0" 250 10'-0" 12'-0" 14-0" 6'-0" 500 8'-0" 10'-0" 12'-0" 1000 6'-0" 8'-0" D 5" 5" 5" 5" 6" 5" 5" 5" 6" 6" 6" E 4" 4" 6" 7" 8" 6" 7" 9" 6" 4" 6" F 4" 4" 4" 4" 4" 5" 5" 5" 6 1/2" 6 1/2" 6 1/2" S 26" 26" 26" 26" 26" 26" 26" 26" 26" 26" 26" W 48" 48" 48" 48" 48" 48" 48" 48" 60" 60" 60" FW 3.00" 3.00" 3.00" 3.00" 3.33" 3.00" 3.00" 3.00" 3.33" 3.33" 3.33" B = 8'-0" WEIGHT MODEL PBB2586 PBB2588 PBB25810 PBB25812 PBB25814 PBB586 PBB588 PBB5810 PBB5812 PBB186 PBB188 (LBS.) 2194 2222 3508 4172 4866 3514 4178 5479 5723 3812 5673 MODEL PBB25106 PBB25108 PBB251010 PBB251012 PBB251014 PBB5106 PBB5108 PBB51010 PBB51012 PBB1106 PBB1108 B = 10'-0" WEIGHT (LBS.) 2223 2243 3537 4201 4895 3544 4208 5509 5762 3850 5711 MODEL PBB25126 PBB25128 PBB251210 PBB251212 PBB251214 PBB5126 PBB5128 PBB51210 PBB51212 PBB1126 PBB1128 B = 12'-0" WEIGHT (LBS.) 2253 2273 3567 4231 4925 3573 4237 5538 5800 3889 5750

F

A

D 2" FW

Portable Jib Crane Accessories: Tagline Kits Trolleys Hoists Rotation Stops B Optional Base sizes Lifting Lugs

Not to be used as a forklift truck attachmentBASE 1000# Capacity with 6'-0" boom have 3" x 7" fork pockets that extend through the base. All other models have 3-1/2" x 7-1/2" fork pockets.

E S W Base footprint is square Features: Can be easily moved from place to place Requires no concrete foundation Can be used on floors above ground floor Can be easily stored out of the way 9-3-02

FLOOR


Trolley End Stops Boom Mounting Hardware Boom Assembly Main Bearing Cup (Pressed in at Factory) End Stop Mounting Hardware


Upper Pipe Assembly

Roller Shaft Lock Pin (2)

Main Bearing Cone Upper Bearing Pin Jib Column Anchor Bolt Bolt Hardware

Lower Roller (2) Thrust Washer (2)

Column Gussets Jib Base Plate


Portable Jib Assembly Detail 8-29-02 Not to scaleDWG NO

PBB-1005-A

WORKSTATION JIB CRANECONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com360 Boom Rotation

FEATURES:

Load Trolley Included

Available in 100 lb., 250 lb., and 500 lb. capacity Boom reach up to 10 ft. High-strength enclosed track protects running surface from dirt for minimal resistance. Lifetime lubricated and sealed wheel bearings in trolley Easy to control load placement Fast installation: 100 lb. and 250 lb. capacity units can be anchored to most existing concrete floors. Easy to relocate OPTIONS: Anchor bolt kits Festooning trolley kit Rotation stops Top entry electrical collector Mounting template Adjustable rubber trolley stops Light weight electric chain hoist Use this ergonomically designed jib for repetitive motion material handling applications. Low friction track and trolley reduces operator fatigue in pick and place operations. Special trolley, included with the jib crane, will accept most small capacity hoist hooks.8-28-02

WSB WORKSTATION JIB CRANE SPECIFICATIONSMODEL NO. WSB1106 WSB1108 WSB11010 WSB25106 WSB25108 WSB251010 WSB5106 WSB5108 WSB51010 Cap. (lbs.) 100 100 100 250 250 250 500 500 500 "A" (ft.) 6 8 10 6 8 10 6 8 10 "D" (in.) 6-3/4 7-3/4 8-3/4 8-3/4 8-3/4 9-3/4 9-3/4 9-3/4 11-3/4A

"G" (in.) 2 2 2 2 2 2 2 2 2

"E" (in.) 6 6 6 6 6 6 12 12 12

"W" (in.) 48 60 60 48 60 60 48 60 60

Base Plt. 15S4 15S4 15S4 23H6 23H6 23H6 35H6 35H6 35H6

Anchor Dia. (in.) 3/4 3/4 3/4 1 1 1 1 1 1

Wt. (lbs.) 379 424 479 424 549 604 614 754 834

BOOM ASSEMBLYD G

Jib Crane Accessories: Anchor bolt kits Festooning trolley kit Templates (paper & plywood) Top entry electrical collector Adjustable rubber stops Rotation stops Hoists (electric & manual)

UPPER PIPE TROLLEY (INCLUDED) COLUMN ASSEMBLY10' 0"

BASE PLATE4"

EXPANSION TYPE ON 100 & 250 LB. JIBS 'L' TYPE (SHOWN) ON 500 LB. JIBS

ANCHORS (BY OTHERS)

FLOORE 3/4 E SQUARE CONCRETE FOOTING W

Base Plates

15S415"

12"

23H623"

20"

35H6

32"

35"7-10-06


Boom Assembly Boom Mounting Hardware

End Stop Mounting Hardware Trolley End Stop Trolley (Included) Shim here to adjust boom level.

Main Bearing Cup (Pressed in at Factory)


Upper Pipe Assembly

Roller Shaft (2) Lock Pin (2)

Main Bearing Cone Upper Bearing Pin Jib Column Anchor Bolt Hardware

Lower Roller (2) Thrust Washer (2) Column Gussets Jib Base Plate (100 lb. models have square base plates) 'L' anchor bolts shown are recommended for 500 lb. capacity models. Expansion anchors may be used on 100 lb. and 250 lb. capacity models. (Anchors not included)

Concrete Footing


Workstation Jib Assembly Detail 8-29-02 Not to scaleDWG NO

WSB-1005


FULL-CANTILEVERED WALL MOUNT JIB CRANE

O. LN . DE INC O. MO S, LN RIE RIA ST 6 SE DU I 5495 X IN , W 01 TR ENAH 2-01 N NE 0-72 CO 92

180 rotation Ideal for maximun headroom and trolley travel Mount at any height on wall or building columns where strength permits and true vertical alignment is possible High grade steel components for long life Hinges with self-lubricating teflon bearings and hardened pins Capacities to 6,000 lbs. - standard lengths to 20' Primed and painted safety yellow Options: Hoists and trolleys Boom rotation bumpers Tagline festoon kits Contact us for special requests.5-2-08

WMCC FULL CANTILEVERED JIB CRANE SPECIFICATIONS4 1/2" ABOOM

DVERTICAL BEAM END STOP

6" B 2" E 2"WALL BRACKET

G

FW

3"6 BOLT HOLES

CONSULT FACTORY FOR: - Special boom lengths and capacities - Motorized rotation - Mounting hardware - Hinge kits - Matching hoist and trolley systemsF 10" 10" 12" 12" 12" 12" 16-3/8" 12" 12" 12" 16-3/8" 16-3/8" 16-3/8" 16-3/8" 16-3/8" 16-3/8" 16-3/8" 16-3/8" 16-3/8" 16" 16" 16-3/8" 16-3/8" 16-3/8" 16" 16" 18" 18" 18" 18" 22" 22" 22" 22" 22" G 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 2" 3" 3" 3" 2" 2" 2" 2" 3" 3" 3" THRUST BOLT HOLE & PULL (LBS.) DIA. 2080 9/16" 2641 9/16" 2425 9/16" 2871 9/16" 3526 9/16" 4049 9/16" 4967 9/16" 3680 9/16" 4662 9/16" 5668 9/16" 5046 9/16" 6069 9/16" 6940 9/16" 9/16" 5394 5110 9/16" 5226 11/16" 6329 11/16" 7453 11/16" 11/16" 7272 8561 11/16" 9643 11/16" 11/16" 9823 11/16" 12359 11/16" 14924 14240 11/16" 11/16" 14052 11/16" 15998 14521 11/16" 14675 11/16" 18448 11/16" 14871 11/16" 17440 11/16" 11/16" 18844 18629 11/16" 16512 13/16" WEIGHT (LBS.) 205 230 304 329 442 479 722 277 314 350 482 621 672 875 371 508 559 610 765 1083 1163 469 529 589 887 1256 1465 1840 679 759 974 1054 1402 1743 2135

F

2"

WALL BRACKET BOLT PATTERN A 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' 8' 10' 12' 14' 16' 18' 20' B 3' 3' 4' 4' 4' 4' 4' 3' 3' 3' 4' 4' 4' 6' 4' 5' 5' 5' 6' 6' 6' 4' 4' 4' 5' 6' 6' 7'-6" 4' 4' 6' 6' 6'-6" 7'-6" 9'-6" D 6" 6" 6" 6" 8" 8" 10" 8" 8" 8" 8" 10" 10" 12-3/8" 8" 10" 10" 10" 12-3/8" 16" 16" 12-3/8" 12-3/8" 12-3/8" 16" 21" 21" 23 3/4" 16" 16" 16" 16" 21" 23 3/4" 23 3/4" FW

2"

MODEL NO. CAPACITY WMCC508 WMCC510 WMCC512 WMCC514 WMCC516 WMCC518 WMCC520 WMCC108 WMCC110 WMCC112 WMCC114 WMCC116 WMCC118 WMCC120 WMCC208 WMCC210 WMCC212 WMCC214 WMCC216 WMCC218 WMCC220 WMCC408 WMCC410 WMCC412 WMCC414 WMCC416 WMCC418 WMCC420 WMCC608 WMCC610 WMCC612 WMCC614 WMCC616 WMCC618 WMCC620 500 LB. 500 LB. 500 LB. 500 LB. 500 LB. 500 LB. 500 LB. 1000 LB. 1000 LB. 1000 LB. 1000 LB. 1000 LB. 1000 LB. 1000 LB. 2000 LB. 2000 LB. 2000 LB. 2000 LB. 2000 LB. 2000 LB. 2000 LB. 4000 LB. 4000 LB. 4000 LB. 4000 LB. 4000 LB. 4000 LB. 4000 LB. 6000 LB. 6000 LB. 6000 LB. 6000 LB. 6000 LB. 6000 LB. 6000 LB.

E 7" 7" 7" 7" 7" 7" 7" 7" 7" 7" 7" 7" 7" 7" 7" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8" 8"

*

* *

3 3/8" 3 3/8" 3 3/8" 3 3/8" 4" 4" 4 5/8" 4" 4" 4" 4" 4 5/8" 4 5/8" 6-1/2" WF 4" 4 5/8" 4 5/8" 4 5/8" 6-1/2" WF 7" WF 7" WF 6-1/2" WF 6-1/2" WF 6-1/2" WF 7" WF 6-1/2" WF 6-1/2" WF 7" WF 7" WF 7" WF 7" WF 7" WF 6-1/2" WF 7" WF 7" WF

WF INDICATES THAT THIS JIB CRANE USES A WIDE-FLANGE BEAM. THE TROLLEY USED ON THIS CRANE MUST BE DESIGNED TO OPERATE ON A WIDE-FLANGE BEAM. * THESE CRANES SHIP IN TWO PIECES AND HAVE BOLT ON BOOMS.

10-27-09


WALL BRACKET A END STOP D 6" 3" B 2" E 2"FW

CAPACITY WEIGHT A B D

4-1/2"

F HINGE PIN

E 2" 2" WALL BRACKET MOUNTING BOLT PATTERN (6) HOLES F FW MOUNTING HOLE DIA. NOTES NOT DESIGNED FOR OUTDOOR USE

INSTALLATION NOTESNOTE: PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION. 1. DETERMINE THE SUPPORTING STRUCTURE IS ADEQUATE TO SUPPORT THE CRANE. 2. USE THE WALL BRACKET PATTERN SHOWN TO MARK AND DRILL THE BOLT HOLES IN THE SUPPORTING STRUCTURE. BE SURE THAT BOTH HINGE PINS SHARE A COMMON TRUE VERTICAL CENTERLINE. 3. RAISE THE CRANE INTO POSITION AND BOLT THE HINGES TO THE SUPPORTING STRUCTURE. USE MINIMUM GRADE 5 BOLTS AND NUTS (SUPPLIED BY OTHERS) USE BOLTS 1/16" LESS IN DIAMETER THAN THE BOLT HOLES. 4. INSTALL HOIST AND TROLLEY BY REMOVING END STOPS. SLIDE THE TROLLEY ONTO THE BOOM AND REPLACE THE END STOPS. 5. CONTACT CONTRX INDUSTRIES (920) 722-0101 FOR ADDITIONAL ASSISTANCE.


NOT TO SCALE

SALES-WMCC 12-13-05WJ

FULL CANTILEVER WALL MOUNT JIBDWG NO

OVERBRACED TIE-ROD JIB CRANECONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com WALL MOUNTED

. NO DEL . . MO O INC LN IES, RIA SE STR 956 DU I 54 X IN , W0101 NTR ENAH 2CO NE 920-72

180 rotation Economical hook coverage with rotation Single tie-rod with threaded ends for easy field adjustment Mount at any height on wall or building columns where strength permits and true vertical alignment is possible High grade steel components for long life Hinges with self-lubricating teflon bearings and hardened pins Capacity to 6,000 lbs. - standard lengths to 20' 0" Primed and painted safety yellow Options: Hoists and trolleys Boom rotation bumpers Tagline festoon kits Contact us for special requests.5-2-08

WMC OVERBRACED TIE ROD JIB CRANE SPECIFICATIONSWALL BRACKET TIE ROD HINGE TIE ROD YOKE WALL BRACKET BOLT PATTERN2" E 6" 3"

6 BOLT HOLES

HINGE PINB

TIE ROD

2" 2" F 2"

BOOM

BOOM BRACKETD

END STOP4 1/2" A

2"

FW

WEIGHT BOLT HOLE THRUST (LBS.) DIA. & PULL (LBS.) 190 2367 1'-3" 7" 3 3/8" 6" 2'-9" 9/16" 8' 500 LB. WMC508 220 2731 1'-6" 7" 3 3/8" 6" 3'-0" 9/16" 10' 500 LB. WMC510 250 2648 2'-0" 7" 3 3/8" 6" 3'-9" 9/16" 12' 500 LB. WMC512 280 2603 7" 2'-0" 3 3/8" 6" 4'-6" 14' 9/16" WMC514 500 LB. 311 2463 2'-0" 7" 3 3/8" 6" 5'-6" 16' 9/16" 500 LB. WMC516 445 2738 2'-0" 7" 4" 8" 6'-0" 18' 9/16" 500 LB. WMC518 487 2860 2'-3" 7" 4" 8" 6'-6" 20' 9/16" WMC520 500 LB. 190 4118 1'-3" 7" 3 3/8" 6" 2'-9" 9/16" 8' 1000 LB. WMC108 220 4720 1'-6" 7" 3 3/8" 6" 3'-0" 9/16" 10' 1000 LB. WMC110 250 4545 2'-0" 7" 3 3/8" 6" 3'-9" 9/16" 12' 1000 LB. WMC112 280 4440 2'-0" 7" 3 3/8" 6" 4'-6" 14' 9/16" WMC114 1000 LB. 311 4175 7" 2'-0" 3 3/8" 6" 5'-6" 16' 9/16" WMC116 1000 LB. 445 4499 7" 2'-0" 4" 8" 6'-0" 18' 9/16" WMC118 1000 LB. 487 4662 7" 2'-3" 4" 8" 6'-6" 20' 9/16" WMC120 1000 LB. 190 1'-3" 7681 7" 3 3/8" 6" 2'-9" 9/16" 8' 2000 LB. WMC208 220 1'-6" 8766 8" 3 3/8" 6" 3'-0" 11/16" 10' 2000 LB. WMC210 250 2'-0" 8406 8" 3 3/8" 6" 3'-9" 11/16" 12' 2000 LB. WMC212 360 2'-0" 8312 8" 4" 8" 4'-6" 11/16" 14' WMC214 2000 LB. 403 2'-3" 7802 8" 4" 8" 5'-6" 11/16" 16' WMC216 2000 LB. WMC218 2000 LB. 18' 6'-0" 8" 8" 2'-6" 8082 4" 444 11/16" WMC220 2000 LB. 20' 6'-0" 10" 8" 4 5/8" 2'-6" 9266 11/16" 624 235 1'-3" 14822 8" 4" 8" 2'-9" 11/16" 8' 4000 LB. WMC408 276 16895 1'-6" 8" 4" 8" 3'-0" 11/16" 10' 4000 LB. WMC410 318 16182 1'-9" 8" 4" 8" 3'-9" 11/16" 12' 4000 LB. WMC412 WMC414 4000 LB. 14' 4'-6" 8" 8" 2'-0" 15724 4" 360 11/16" 512 14880 2'-3" 4 5/8" 8" 10" 5'-6" 16' 11/16" WMC416 4000 LB. 568 15384 2'-3" 4 5/8" 8" 10" 6'-0" 18' 11/16" WMC418 4000 LB. WMC420 4000 LB. 20' 6'-6" 12-3/8" 6-1/2" WF 8" 2'-6" 15973 713 11/16" 1'-3" WMC608 6000 LB. 8' 2'-9" 8" 22070 4" 8" 265 13/16" 1'-6" WMC610 6000 LB. 10' 3'-3" 8" 23193 4" 8" 310 13/16" 1'-9" WMC612 6000 LB. 12' 4'-0" 10" 22668 4 5/8" 8" 435 13/16" WMC614 6000 LB. 14' 4'-9" 10" 8" 2'-0" 22251 4 5/8" 495 13/16" 585 21966 2'-3" 4 5/8" 8" 10" 5'-6" 16' 13/16" WMC616 6000 LB. 2'-3" WMC618 6000 LB. 18' 6'-3" 16" 22160 7" WF 8" 875 13/16" WMC620 6000 LB. 20' 7'-0" 16" 8" 2'-6" 7" WF 22056 13/16" 955 WF INDICATES THAT THIS JIB CRANE USES A WIDE-FLANGE BEAM. THE TROLLEY USED ON THIS CRANE MUST BE DESIGNED TO OPERATE ON A WIDE-FLANGE BEAM. MODEL NO. CAPACITY A B D FW E F

CONSULT FACTORY FOR: Special boom lengths and capacities Motorized rotation Mounting hardware Hinge kits Matching hoist and trolley systems

4-24-08


WALL BRACKET TIE ROD HINGE TIE ROD YOKE TIE ROD HINGE PIN B BOOM F D END STOP 4-1/2" A 2" FW 6" 3" CAPACITY WEIGHT A B D E F INSTALLATION NOTESNOTE: PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION. 1. DETERMINE THE SUPPORTING STRUCTURE IS ADEQUATE TO SUPPORT THE CRANE. 2. USE THE WALL BRACKET PATTERN SHOWN TO MARK AND DRILL THE BOLT HOLES IN THE SUPPORTING STRUCTURE. BE SURE THAT BOTH HINGE PINS SHARE A COMMON TRUE VERTICAL CENTERLINE. 3. BOLT THE UPPER HINGE TO THE MOUNTING SURFACE. USE MINIMUM GRADE 5 BOLTS AND NUTS (SUPPLIED BY OTHERS) USE BOLTS 1/16" LESS IN DIAMETER THAN THE BOLT HOLES. 4. WHILE SUPPORTING THE BOOM HORIZONTALLY, BOLT THE LOWER HINGE AND BEAM TO THE MOUNTING SURFACE. 5. ATTACH THE ROD BETWEEN THE UPPER HINGE AND BOOM BRACKET WITH THE NUTS AND WASHERS PROVIDED. ADJUST THE NUTS TO LEVEL THE BOOM.DATE

BOOM BRACKET

2" E 2"

FW MOUNTING HOLE DIA. NOTES NOT DESIGNED FOR OUTDOOR USE

2" 2" WALL BRACKET MOUNTING BOLT PATTERN (6) HOLES


6. INSTALL HOIST AND TROLLEY BY REMOVING END STOPS. SLIDE THE TROLLEY ONTO THE BOOM AND REPLACE THE END STOPS. 7. CONTACT CONTRX INDUSTRIES (920) 722-0101 FOR ADDITIONAL ASSISTANCE.

NOT TO SCALE

SALES-WMC 12-13-05WJ

OVERBRACED TIE ROD WALL MOUNT JIBDWG NO


PILLAR MOUNT JIB CRANE

N CO

O. LN . DE INC O. MO S, LN RIE RIA ST 6 SE DU I 5495 X IN , W 01 TR ENAH 2-01NE 0-72 92

360 rotation Ideal for maximum headroom and trolley travel High grade steel components for long life Mounting plates with spherical roller bearings Capacities to 4,000 lbs. - standard lengths to 20' Primed and painted safety yellow Options: Hoists and trolleys Tagline festoon kits Contact us for more information7-31-08

PORTABLE GANTRY CRANESCONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com

FEATURES OF FIXED HEIGHT & TELESCOPING GANTRIES Capacities From 1 to 5 Ton Spans from 8 to 16 Feet Heights from 8 to 16 Feet Portable Custom Sizes Available 2 Large Steel Swivel Casters 2 Large Steel Swivel Casters with Brakes Standard "I" Beams Painted Safety Yellow Built to meet ANSI and OSHA Requirements

Fixed Height Gantry Crane

APPLICATIONS OF FIXED HEIGHT & TELESCOPING GANTRIES Automotive Trucking Manufacturing Loading Docks Aircraft Implement Marine Warehouses Maintenance

Telescoping Gantry Crane

10-8-03

PORTABLE GANTRY CRANE SPECIFICATIONSOur Fixed Height Gantry Cranes are ideal for use in aircraft, automotive, and marine repair shops. They also work well in warehouses, machine shops, and loading areas. Gantry cranes are supplied with four roller-bearing steel wheels for easy maneuverability. The structural steel legs are welded together at the factory. Gantry crane requires assembly before use.G C FW

D F

E

FLOOR

FIXED HEIGHT GANTRY CRANE SPECIFICATIONS MODEL CAP. STEEL * BEAM WEIGHT C D E F G FW NUMBER (TONS) WHEELS TYPE** (LBS.) 5" 522 3" 5' 10' 8' 9'-5" 5" X 1 5/8" 1 S GC1-8 6" 590 3 3/8" 12' 5' 10' 5" X 1 5/8" 13'-5" 1 S GC1-12 8" 749 4" 16' 5' 10' 5" X 1 5/8" 17'-5" 1 S GC1-16 6" 740 3 3/8" 5' 10' 8' 9'-6" 8" X 1 1/2" 2 S GC2-8 8" 910 4" 12' 5' 10' 8" X 1 1/2" 13'-6" 2 S GC2-12 1062 16' 5' 10' 10" 4 5/8" 17'-6' 8" X 1 1/2" 2 S GC2-16 8" 1020 4" 5' 10' 8" X 2 1/2" 9'-6 5/8" 8' 3 S GC3-8 1188 8" X 2 1/2" 13'-6 5/8" 12' 5' 10' 10" 4 5/8" 3 S GC3-12 1603 8" X 2 1/2" 17'-6 5/8" 16' 5' 10' 13-5/8" 8" 3 W GC3-16 1292 5' 10' 10" 4-5/8" 9'-8 5/8" 8' 8" X 3" 4 S GC4-8 1576 8" X 3" 13'-8 5/8" 12' 5' 10' 10" 4 5/8" 4 S GC4-12 2001 8" X 3" 17'-8 5/8" 16' 5' 10' 13-5/8" 8" 4 W GC4-16 1728 5' 10' 16-3/8" 7-1/8" 9'-8 5/8" 8' 8" X 3" 5 W GC5-8 2050 8" X 3" 13'-8 5/8" 12' 5' 10' 16-3/8" 7-1/8" 5 W GC5-12 2383 8" X 3" 17'-8 5/8" 16' 5' 10' 16-3/8" 7-1/8" 5 W GC5-16 * DIAMETER OF WHEELS BY TREAD WIDTH ** "S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam.

Our Telescopic Height Gantry Cranes have the same abilities as our fixed height gantries with the added benefit of raising or lowering the beam to suit your need. The beam will adjust from 8'-0" to 12'-0" below the beam with positive stops every 6". The beam is raised and lowered with the aid of two cable pullers (included). Locking pins hold the beam at the desired height. TELESCOPING HEIGHT GANTRY CRANE SPECIFICATIONSG C FW

D

CABLE PULLER (2)

F

E

FLOOR

F STEEL * MODEL CAP. BEAM WEIGHT C D E FW G NUMBER (TONS) WHEELS TYPE** (LBS.) MIN. MAX. 827 3" 5" X 1 5/8" 9'-5 9/16" 8' 5' 8' 12' 5" S 1 GCT1-8 895 3 3/8" 6" 5" X 1 5/8" 13'-5 9/16" 12' 5' 8' 12' S 1 GCT1-12 1054 4" 8" 5" X 1 5/8" 17'-5 9/16" 16' 5' 8' 12' S 1 GCT1-16 977 3 3/8" 6" 8" X 1 1/2" 9'-6 5/8" 8' 5' 8' 12' S 2 GCT2-8 1167 4" 8" 8" X 1 1/2" 13'-6 5/8" 12' 5' 8' 12' S 2 GCT2-12 1319 10" 4 5/8" 8" X 1 1/2" 17'-6 5/8" 16' 5' 8' 12' S 2 GCT2-16 1147 4" 8" 8" X 2 1/2" 9'-6 5/8" 8' 5' 8' 12' S 3 GCT3-8 1315 10" 4 5/8" 8" X 2 1/2" 13'-6 5/8" 12' 5' 8' 12' S 3 GCT3-12 1730 8" X 2 1/2" 17'-6 5/8" 16' 5' 8' 12' 13-5/8" 8" W 3 GCT3-16 1477 9'-8 5/8" 8' 5' 8' 12' 10" 4-5/8" 8" X 3" S 4 GCT4-8 1761 13'-8 5/8" 12' 5' 8' 12' 10" 4 5/8" 8" X 3" S 4 GCT4-12 2186 17'-8 5/8" 16' 5' 8' 12' 13-5/8" 8" 8" X 3" W 4 GCT4-16 1905 9'-8 5/8" 8' 5' 8' 12' 16-3/8" 7-1/8" 8" X 3" W 5 GCT5-8 2227 13'-8 5/8" 12' 5' 8' 12' 16-3/8" 7-1/8" 8" X 3" W 5 GCT5-12 2560 17'-8 5/8" 16' 5' 8' 12' 16-3/8" 7-1/8" 8" X 3" W 5 GCT5-16 * DIAMETER OF WHEELS BY TREAD WIDTH ** "S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam.

FIXED & TELESCOPING GANTRY CRANESSemi-steel heavy-duty swivel casters with roller bearings are standard equipment. Two casters are supplied with brakes. Gantries are easily disassembled and assembled for relocation. Contact factory for special heights, spans, and options.6-26-06


C G

FW

D

F CAPACITY WEIGHT E C D W E F G FW NOTES NOT DESIGNED FOR OUTDOOR USE W

OPTIONS: (2) STEEL SWIVEL CASTERS (2) STEEL SWIVEL CASTERS WITH BRAKES


NOT TO SCALE

SALES-GC 12-13-05WJ

FIXED HEIGHT GANTRY CRANEDWG NO

C G

FW

D

MAX MIN CAPACITY WEIGHTCABLE PULLER (2) INCLUDED

E

C D W E G FW W

NOTES

NOT DESIGNED FOR OUTDOOR USE

MIN MAX

1377 Kimberly Dr., Neenah, WI 54956

OPTIONS: (2) STEEL SWIVEL CASTERS (2) STEEL SWIVEL CASTERS WITH BRAKES HEIGHT IS ADJUSTABLE IN 6" INCREMENTS

www.contrx.com

DATE

NOT TO SCALE

SALES-GCT 12-13-05WJ

TELESCOPING GANTRY CRANEDWG NO

TELESCOPING JIB LIFTCONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com Converts lift truck into a crane inexpensively Moves cumbersome items your forks can't reach. Crane reaches out and picks up from overhead. Reaches through or over obstructions.

Check with manufacturer of your lift truck for load capabilities before using.

1 2 3 4 5 6 7

Alternate Hook Positions Telescoping Boom Boom Handle Safety Swivel Hooks (2) Fork Pockets 48" Safety Chain with Grab Hook Spring Loaded Boom Lock

7 2 5 3 1

6

4

Minimize manhandling of shipments and equipment without investing a lot of money in new power equipment. Jib lift lets you convert your standard lift truck into a mobile crane at minimal cost. You can enjoy the convenience of this versatile equipment without duplicating power equipment...and it's easy to use. One man can install in minutes without removing forks, just by slipping onto forks. 48" safety chain anchors it to truck's frame. Constructed of heavy structural steel tubing; two safety swivel hooks provided.

1-22-03

TELESCOPING JIB LIFTSINGLE HOOK CAPACITIES4000 LB. CAPACITY LIFT JIB Forklift Truck Capacity Hook at 24" Load Center Hook Position Pos. (inches) 2000 4000 5000 6000 8000 10,000 1 80 595 1429 1845 2262 3095 3929 2 87-1/2 545 1318 1704 2091 2864 3535 3 95 501 1222 1582 1943 2663 3167 4 102-1/2 463 1138 1476 1813 2488 2868 5 110 429 1064 1382 1699 2334 2621 6 117-1/2 399 999 1298 1598 2197 2413 7 125 373 940 1224 1507 2075 2235 8 132-1/2 349 887 1157 1426 1965 2082 9 140 327 840 1096 1353 1865 1949 MAX. JIB CAP. 4000 3535 3167 2868 2621 2413 2235 2082 1949 6000 LB. CAPACITY LIFT JIB 8000 LB. CAPACITY LIFT JIB Forklift Truck Capacity MAX. Forklift Truck Capacity MAX. at 24" Load Center at 24" Load Center JIB JIB 10,000 12,000 14,000 CAP. 16,000 18,000 20,000 CAP. 3828 4662 5495 6000 6087 6920 7754 8000 3540 4313 5086 5302 5633 6406 6974 6974 3291 4012 4733 4750 5240 5961 6182 6182 3074 3749 4302 4302 4897 5551 5551 5551 2882 3517 3931 3931 4594 5037 5037 5037 2712 3311 3619 3619 4326 4610 4610 4610 2560 3127 3353 3353 4086 4250 4250 4250 2423 2962 3123 3123 3871 3942 3942 3942 2300 2813 2923 2923 3676 3676 3676 3676

JIB LIFT CAPACITIES DEPEND COMPLETELY ON CAPACITY OF FORK LIFT BEING USED.SINGLE HOOK CAPACITIES ARE BASED ON A FORKLIFT TRUCK WITH DIMENSIONS SHOWN BELOW

FORK LIFT TRUCK CAPACITY AT 24" LOAD CENTER

WHEEL CENTER

16"

24"

CHECK WITH MANUFACTURER OF YOUR FORKLIFT FOR LOAD CAPABILITIES BEFORE USING

IMPORTANT TRUCK FORKS MUST EXTEND THROUGH FULL LENGTH OF FORK TUBES

MAX. CAP. MODEL DIM. DIM. (LBS) NUMBER "S" "W" 4000 JLT411 11" 17" 4000 JLT424 24" 30" 4000 JLT430 30" 36" 4000 JLT436 36" 42" 4000 JLT442 42" 48" 6000 JLT613 13" 21" 6000 JLT624 24" 32" 6000 JLT630 30" 38" 6000 JLT636 36" 44" 6000 JLT642 42" 50" 8000 JLT824 24" 32" 8000 JLT836 36" 44" 8000 JLT848 48" 56"

DIM. DIM. WT. FORK "TL" "H.U.B." (LBS) POCKETS 24" 10" 2-1/2" X 5-1/2" 373 10" 24" 2-1/2" X 5-1/2" 413 10" 24" 2-1/2" X 5-1/2" 434 10" 24" 2-1/2" X 5-1/2" 455 10" 24" 2-1/2" X 5-1/2" 476 10" 24" 3-1/2" X 7-1/2" 519 10" 24" 3-1/2" X 7-1/2" 544 10" 24" 3-1/2" X 7-1/2" 566 10" 24" 3-1/2" X 7-1/2" 588 24" 10" 3-1/2" X 7-1/2" 610 32" 10" 3-1/2" X 7-1/2" 667 32" 10" 3-1/2" X 7-1/2" 787 32" 12" 3-1/2" X 7-1/2" 909

145" MAX 85" MIN

9 POSITIONS 7-1/2" INCREMENTS

H.U.B. S W TL

HOOK POSITION 9

SAFETY PIN LOCKS BOOM IN POSITION

FEATURES Handles long loads in closed trucks High and long reaches for inaccessible areas High underclearances and bulky load handling 10-10-08


PIVOT BOOM JIB LIFTCONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com1 2 3 4 5 6 7 8 3

Converts lift truck into a crane inexpensively Moves cumbersome items your forks can't reach. Crane reaches out and picks up from overhead. Increases load height Adjustable boom height and reach Reaches through or over obstructions.

Alternate Hook Positions Telescoping Boom Boom Handle Safety Swivel Hook Fork Pockets 48" Safety Chain with Grab Hook Spring Loaded Boom Lock Angle Adjusting Pin2 7 4

1

8 6 5

Pivoting jib lift lets you convert your standard lift truck into a mobile crane in minutes at minimal cost. Lift loads higher than your lift truck forks can reach. Pivoting boom adjusts from horizontal to 50. Enjoy the convenience of this versatile attachment without duplicating existing equipment ...and it's easy to use. One person can install without removing forks. 48" safety chain ties jib lift to truck frame. Constructed of heavy structural steel tubing; one swivel hook provided.1-22-03

PIVOT BOOM JIB LIFTSINGLE HOOK CAPACITIES4000 LB. CAPACITY LIFT JIB Forklift Truck Capacity Hook at 24" Load Center Hook Position Pos. (inches) 2000 4000 5000 6000 8000 10,000 1 80 595 1429 1845 2262 3095 3929 2 87-1/2 545 1318 1704 2091 2864 3535 3 95 501 1222 1582 1943 2663 3167 4 102-1/2 463 1138 1476 1813 2488 2868 5 110 429 1064 1382 1699 2334 2621 6 117-1/2 399 999 1298 1598 2197 2413 7 125 373 940 1224 1507 2075 2235 8 132-1/2 349 887 1157 1426 1965 2082 9 140 327 840 1096 1353 1865 1949 MAX. JIB CAP. 4000 3535 3167 2868 2621 2413 2235 2082 1949 6000 LB. CAPACITY LIFT JIB 8000 LB. CAPACITY LIFT JIB Forklift Truck Capacity MAX. Forklift Truck Capacity MAX. at 24" Load Center at 24" Load Center JIB JIB 10,000 12,000 14,000 CAP. 16,000 18,000 20,000 CAP. 3828 4662 5495 6000 6087 6920 7754 8000 3540 4313 5086 5302 5633 6406 6974 6974 3291 4012 4733 4750 5240 5961 6182 6182 3074 3749 4302 4302 4897 5551 5551 5551 2882 3517 3931 3931 4594 5037 5037 5037 2712 3311 3619 3619 4326 4610 4610 4610 2560 3127 3353 3353 4086 4250 4250 4250 2423 2962 3123 3123 3871 3942 3942 3942 2300 2813 2923 2923 3676 3676 3676 3676 MAX. CAP. (LBS) 4000 4000 6000 6000 8000 8000

JIB LIFT CAPACITIES DEPEND COMPLETELY ON CAPACITY OF FORK LIFT BEING USED.SINGLE HOOK CAPACITIES ARE BASED ON A FORKLIFT TRUCK WITH DIMENSIONS SHOWN BELOW

FORK LIFT TRUCK CAPACITY AT 24" LOAD CENTER

MODEL NUMBER PB-JLT424 PB-JLT436 PB-JLT624 PB-JLT636 PB-JLT836 PB-JLT848

DIM. "S" 24" 36" 24" 36" 36" 48"

DIM. "W" 30" 44" 32" 44" 44" 56"

DIM. "TL" 24" 24" 24" 24" 32" 32"

DIM. WT. "H.U.B." (LBS) 18-1/2" 491 19-1/2" 588 19-1/2" 640 23-1/2" 718 27-1/2" 933 27-1/2" 1025

WHEEL CENTER

16"

24"

IMPORTANT TRUCK FORKS MUST EXTEND THROUGH FULL LENGTH OF MOUNTING TUBES

CHECK WITH MANUFACTURER OF YOUR FORKLIFT FOR LOAD CAPABILITIES BEFORE USING

145" MAX 85" MIN

9 POSITIONS 7-1/2" INCREMENTS

H.U.B.

SAFETY PIN LOCKS BOOM IN POSITION

HOOK POSITION 9

S W

TL

FEATURES Handles long loads in closed trucks High and long reaches for inaccessible areas High underclearances and bulky load handling Adjustable at 10 increments from horizontal to 50 Safety chain secures jib lift to forklift truck 1-22-03


PALLET LIFTERCONTRX INDUSTRIES 1377 Kimberly Drive Neenah, WI 54956-1642 Phone (920) 722-0101 Fax (920) 725-1394 www.contrx.com

8-16-02

Contrx Standard Pallet Lifters make your crane into an inexpensive forklift. You can afford pallet lifting convenience at a small cost. Speed up handling and movement of pallet loads, loading and unloading. Reach areas such as flat and gondola cars, open top trucks, and congested areas with a pallet lifter. Contrx brand pallet lifters are designed to hang level when empty or with a properly balanced load. See table on reverse side for capacities and dimensions. Contact your local dealer for custom dimensions.

PALLET LIFTER DIMENSION & WEIGHT CHARTA B CAP MODEL (lbs.) (in.) (in.) 24 12 500 PL524 30 15 500 PL530 36 18 500 PL536 42 21 500 PL542 48 24 500 PL548 PL130 1000 30 15 PL136 1000 36 18 PL142 1000 42 21 PL148 1000 48 24 PL236 2000 36 18 PL242 2000 42 21 PL248 2000 48 24 PL336 3000 36 18 PL342 3000 42 21 PL348 3000 48 24 PL436 4000 36 18 PL442 4000 42 21 PL448 4000 48 24 PL636 6000 36 18 PL642 6000 42 21 PL648 6000 48 24 PL836 8000 36 18 PL842 8000 42 21 PL848 8000 48 24 PL1036 10,000 36 18 PL1042 10,000 42 21 PL1048 10,000 48 24 F (in.) 20 20 25 25 25 20 25 25 25 25 25 25 25 25 25 25 25 25 27 27 27 27 27 27 27 27 30 G (in.) 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48

B

G

Center of gravity of lifter & load.A

Lifting Bail

Handle

Smaller pallets may be lifted as long as their center of gravity is located under the lifting bail. Specify hook size when ordering to ensure compatibility with lifting bail size.F

4-1-08



BRIDGE CRANES

DOUBLE GIRDER TOP RUNNINGStandard options Double reduction helical gearmotor for reduced wear and long life Adjustable torque magnetic disc brake for smooth operation Machined steel crane and trolley wheels for smooth and quiet operation Top quality hoists matched to the duty required for each bridge crane Custom engineered to fit your application11-19-02

Available custom options Independent traveling pendant Variable frequency type drive motor control Radio remote control operation Travel limit switches, warning lights, & horn 60 minute motors & special insulation Catwalks & service platforms Heat shields Runway rails & beams

TYPES OF STANDARD BRIDGE CRANESDOUBLE GIRDER TOP RUNNING WITH DUAL OUTRIGGERS

SINGLE GIRDER TOP RUNNING WITH SINGLE OUTRIGGER

SINGLE GIRDER UNDER RUNNING WITH DUAL OUTRIGGERS SINGLE GIRDER UNDER RUNNING WITH NO OUTRIGGERS

SINGLE GIRDER TOP RUNNING WITH CAP CHANNEL


11-19-02

Jib Crane

Documents

Transcript of Jib Crane