JCB WHEEL LOADER | 411 HT

STATIC DIMENSIONS – Standard Height Arm

STATIC DIMENSIONS – Standard Height Arm STATIC DIMENSIONS – High Lift Arm

STATIC DIMENSIONS – High Lift Arm

A

B C D

E

G

H

H1

J F

A

B C D

E

G

H

H1

J F

ft-in (mm)

A Overall Length with Standard Bucket 19-7 (5978)

B Axle to Pivot Pin 3-10 (1166)

C Wheel Base 8-10 (2700)

D Axle to Counterweight Face 4-6 (1375)

E Minimum Ground Clearance 1-4 (410)

F Height Over Exhaust 9-7 (2928)

G Width Over Cab 5-0 (1515)

H Width Over Tires 7-3 (2203)

H1 Wheel Track 5-11 (1800)

J Height Over Cab 10-1 (3078)

Pin Height (maximum) 11-5 (3487)

Overall Operating Height 14-6 (4427)

Front Axle Weight lb (kg) 7936 (3600)

Rear Axle Weight lb (kg) 9950 (4513)

Total Weight lb (kg) 18,636 (8453)

Inside Radius 8-7 (2608)

Maximum Radius 17-9 (5414)

Articulation Angle degrees ± 40°

Data based on machine equipped with a 1.6 yd3, direct mounted bucket with bolt on toeplates and Michelin 15.5R25 XHA (L3) tires

ft-in (mm)

A Overall Length with Standard Bucket 20-0 (6090)

B Axle to Pivot Pin 4-2 (1278)

C Wheel Base 8-10 (2700)

D Axle to Counterweight Face 4-6 (1375)

E Minimum Ground Clearance 1-4 (410)

F Height Over Exhaust 9-7 (2928)

G Width Over Cab 5-0 (1515)

H Width Over Tires 7-3 (2203)

H1 Wheel Track 5-11 (1800)

J Height Over Cab 10-1 (3078)

Pin Height (maximum) 11-11 (3621)

Overall Operating Height 14-11 (4559)

Front Axle Weight lb (kg) 8271 (3752)

Rear Axle Weight lb (kg) 8027 (3641)

Total Weight lb (kg) 19,341 (8773)

Inside Radius 8-7 (2608)

Maximum Radius 17-11 (5465)

Articulation Angle degrees ± 40°

Data based on machine equipped with a 1.6 yd3, direct mounted bucket with bolt on toeplates and Michelin 5.5R25 XHA (L3) tires

MAX ENGINE POWER: 100 hp (74 kW) MAX OPERATING WEIGHT: 19,255 lb (8,734 kg) MAX LOADER CAPACITY: 2.2 yd3 (1.7 m3)

JCB WHEEL LOADER | 411 HT

LOADER DIMENSIONS – Standard Height Arm

Tipping Loads Dimensions

Op Weight Straight Full Turn Vertical Width

Tire size Manufacturer Type Rating lb (kg) lb (kg) lb (kg) in (mm) in (mm)

15.5 - 25 (crossply) Goodyear SGL D/L 12 Ply L2 -347 (-158) -207 (-94) -202 (-92) -0.157 (-4) +0.276 (+7)

15.5 - 25 (crossply) Goodyear HRL D/L 12 Ply L3 -273 (-124) -163 (-74) -158 (-72) 0 0

15.5 R 25 (radial) Goodyear GP - 2B L2 0 0 0 -0.157 (-4) +0.276 (+7)

15.5 R 25 (radial) Michelin XTLA L2 -106 (-48) -64 (-29) -62 (-28) -0.157 (-4) +0.276 (+7)

15.5 R 25 (radial) Michelin XMINED2 L5 +961 (+436) +580 (+263) +560 (+254) +1.654 (+42) +0.118 (+3)

CHANGES TO OPERATING PERFORMANCE AND DIMENSIONS

T

PO

RQ

S

M

N

Bucket Mounting Direct Direct Direct Direct Direct Quickhitch Quickhitch Quickhitch Quickhitch Quickhitch

Bucket Type General Purpose General Purpose General Purpose General Purpose Light Material General Purpose General Purpose General Purpose General Purpose Light Material

Bucket Equipment Tipped Teeth Tipped Teeth Reversible T/plate Reversible T/plate Reversible T/plate Tipped Teeth Tipped Teeth Reversible T/plate Reversible T/plate Reversible T/plate

Bucket Capacity (SAE heaped) yd3 (m3) 1.6 (1.2) 1.8 (1.4) 1.6 (1.2) 1.8 (1.4) 2.2 (1.7) 1.6 (1.2) 1.8 (1.4) 1.6 (1.2) 1.8 (1.4) 2.2 (1.7)

Bucket Capacity (struck) yd3 (m3) 1.319 (1.009) 1.542 (1.180) 1.319 (1.009) 1.542 (1.180) 1.780 (1.362) 1.319 (1.009) 1.542 (1.180) 1.319 (1.009) 1.542 (1.180) 1.780 (1.362)

Bucket Width ft-in (mm) 7-5 (2250) 7-10 (2400) 7-5 (2250) 7-10 (2400) 7-10 (2400) 7-5 (2250) 7-10 (2400) 7-5 (2250) 7-10 (2400) 7-10 (2400)

Bucket Weight lb (kg) 1106 (502) 1280 (581) 1164 (528) 1329 (603) 1406 (638) 1056 (479) 1230 (558) 1113 (505) 1278 (580) 1353 (614)

Maximum Material Density lb/yd3 (kg/m3) 3651 (2208) 3148 (1835) 3651 (2208) 3148 (1835) 2552 (1592) 3476 (2102) 2997 (1748) 3476 (2102) 2997 (1748) 2469 (1515)

Tipping Load Straight lb (kg) 13,574 (6157) 13,205 (5990) 13,574 (6157) 13,205 (5990) 13,104 (5944) 12,982 (5889) 12,633 (5730) 12,982 (5889) 12,633 (5730) 12,532 (5685)

Tipping Load Full Turn lb (kg) 11,685 (5300) 11,334 (5141) 11,685 (5300) 11,334 (5141) 11,232 (5095) 11,126 (5047) 10,790 (4894) 11,126 (5047) 10,790 (4894) 10,689 (4848)

Payload lb (kg) 5843 (2650) 5667 (2570) 5843 (2650) 5667 (2570) 5616 (2547) 5563 (2523) 5395 (2447) 5563 (2523) 5395 (2447) 5433 (2424)

Maximum Break Out Force lbf (kN) 16,455 (73.2) 15,219 (67.7) 16,455 (73.2) 15,219 (67.7) 14,095 (62.7) 15,106 (67.2) 14,005 (62.3) 15,106 (67.2) 14,005 (62.3) 12,836 (57.1)

M Dump Angle Maximum degrees 50° 50° 50° 50° 50° 50° 50° 50° 50° 50°

N Roll Back Angle at Full Height degrees 43° 43° 43° 43° 43° 43° 43° 43° 43° 43°

O Roll Back at Carry degrees 47° 47° 47° 47° 47° 47° 47° 47° 47° 47°

P Roll Back at Ground Level degrees 41° 41° 41° 41° 41° 41° 41° 41° 41° 41°

Q Load Over Height ft-in (mm) 10-7 (3242) 10-7 (3242) 10-8 (3237) 10-8 (3237) 10-8 (3237) 10-8 (3259) 10-8 (3259) 10-8 (3254) 10-8 (3254) 10-8 (3254)

R Dump Height (45° dump) ft-in (mm) 8-3 (2524) 8-0 (2450) 8-7 (2624) 8-6 (2582) 8-4 (2532) 8-2 (2490) 8-0 (2426) 8-6 (2590) 8-4 (2548) 8-2 (2498)

S Dig Depth ft-in (mm) 0-4 (108) 0-4 (113) 0-4 (100) 0-4 (105) 0-4 (105) 0-4 (91) 0-4 (96) 0-3 (83) 0-3 (88) 0-3 (88)

T Reach at Dump Height ft-in (mm) 3-5 (1035) 3-6 (1061) 3-0 (925) 3-1 (951) 3-3 (996) 3-7 (1084) 3-8 (1124) 3-2 (974) 3-4 (1014) 3-6 (1059)

Reach Maximum (45° dump) ft-in (mm) 4-11 (1505) 5-2 (1569) 4-7 (1395) 4-9 (1459) 5-0 (1529) 4-5 (1488) 4-10 (1475) 4-5 (1358) 4-6 (1365) 4-8 (1435)

Operating Weight (includes 176 lb/80 kg operator and full fuel tank) lb (kg) 18,578 (8427) 18,752 (8506) 18,636 (8453) 18,801 (8528) 18,878 (8563) 18,958 (8599) 19,132 (8678) 19,015 (8625) 19,180 (8700) 19,255 (8734)

Assumes the machine is fitted with Michelin 15.5R25 XHA (L3) tires.

JCB WHEEL LOADER | 411 HT

LOADER DIMENSIONS – High Lift Arm

Tipping loads Dimensions

Op Weight Straight Full Turn Vertical Width

Tire size Manufacturer Type Rating lb (kg) lb (kg) lb (kg) in (mm) in (mm)

15.5 - 25 (crossply) Goodyear SGL D/L 12 Ply L2 -347 (-158) -194 (-88) -192 (-87) -0.157 (-4) +0.276 (+7)

17.5 R 25 (radial) Goodyear HRL D/L 12 Ply L3 -273 (124) -154 (-70) -150 (-68) 0 0

17.5 R 25 (radial) Goodyear GP - 2B L2 0 0 0 -0.157 (-4) +0.276 (+7)

17.5 R 25 (radial) Michelin XTLA L2 -106 (-48) -60 (-27) -57 (-26) -0.157 (-4) +0.276 (+7)

17.5 R 25 (radial) Michelin XMINED2 L5 +961 (+436) +580 (+263) +560 (+254) +1.654 (+42) +0.118 (+3)

CHANGES TO OPERATING PERFORMANCE AND DIMENSIONS HIGH LIFT ARM

T

PO

RQ

S

M

N

Bucket Mounting Direct Direct Direct Direct Direct Quickhitch Quickhitch Quickhitch Quickhitch Quickhitch

Bucket Type General Purpose General Purpose General Purpose General Purpose Light Material General Purpose General Purpose General Purpose General Purpose Light Material

Bucket Equipment Tipped Teeth Tipped Teeth Reversible T/plate Reversible T/plate Reversible T/plate Tipped Teeth Tipped Teeth Reversible T/plate Reversible T/plate Reversible T/plate

Bucket Capacity (SAE heaped) yd3 (m3) 1.6 (1.2) 1.8 (1.4) 1.6 (1.2) 1.8 (1.4) 2.2 (1.7) 1.6 (1.2) 1.8 (1.4) 1.6 (1.2) 1.8 (1.4) 2.2 (1.7)

Bucket Capacity (struck) yd3 (m3) 1.319 (1.009) 1.542 (1.180) 1.319 (1.009) 1.542 (1.180) 1.780 (1.362) 1.319 (1.009) 1.542 (1.180) 1.319 (1.009) 1.542 (1.180) 1.780 (1.362)

Bucket Width ft-in (mm) 7-5 (2250) 7-10 (2400) 7-5 (2250) 7-10 (2400) 7-10 (2400) 7-5 (2250) 7-10 (2400) 7-5 (2250) 7-10 (2400) 7-10 (2400)

Bucket Weight lb (kg) 1106 (502) 1280 (581) 1164 (528) 1329 (603) 1406 (638) 1056 (479) 1230 (558) 1113 (505) 1278 (580) 1353 (614)

Maximum Material Density lb/yd3 (kg/m3) 3456 (2090) 2979 (1738) 3456 (2090) 2979 (1738) 2415 (1418) 3291 (1990) 2837 (1654) 3291 (1990) 2837 (1654) 2299 (1349)

Tipping Load Straight lb (kg) 12,853 (5830) 12,504 (5672) 12,853 (5830) 12,504 (5672) 12,408 (5628) 12,295 (5577) 11,963 (5426) 12,295 (5577) 11,963 (5426) 11,867 (5383)

Tipping Load Full Turn lb (kg) 11,061 (5017) 10,727 (4866) 11,061 (5017) 10,727 (4866) 10,631 (4822) 10,532 (4777) 10,213 (4633) 10,532 (4777) 10,213 (4633) 10,117 (4589)

Payload lb (kg) 5530 (2508) 5363 (2433) 5530 (2508) 5363 (2433) 5315 (2411) 5266 (2389) 5107 (2316) 5266 (2389) 5107 (2316) 5059 (2295)

Maximum Break Out Force lbf (kN) 16,455 (73.2) 15,219 (67.7) 16,455 (73.2) 15,219 (67.7) 14,095 (62.7) 15,106 (67.2) 14,005 (62.3) 15,106 (67.2) 14,005 (62.3) 12,836 (57.1)

M Dump Angle Maximum degrees 47.5° 47.5° 47.5° 47.5° 47.5° 47.5° 47.5° 47.5° 47.5° 47.5°

N Roll Back Angle at Full Height degrees 44° 44° 44° 44° 44° 44° 44° 44° 44° 44°

O Roll Back at Carry degrees 48.5° 48.5° 48.5° 48.5° 48.5° 48.5° 48.5° 48.5° 48.5° 48.5°

P Roll Back at Ground Level degrees 43.5° 43.5° 43.5° 43.5° 43.5° 43.5° 43.5° 43.5° 43.5° 43.5°

Q Load Over Height ft-in (mm) 11-1 (3371) 11-1 (3376) 11-1 (3371) 11-1 (3371) 11-1 (3371) 11-2 (3393) 11-2 (3393) 11-1 (3388) 11-1 (3388) 11-1 (3388)

R Dump Height (45° dump) ft-in (mm) 8-9 (2658) 8-6 (2594) 9-1 (2758) 8-11 (2716) 8-9 (2666) 8-7 (2624) 8-5 (2560) 8-11 (2724) 8-10 (2682) 8-8 (2632)

S Dig Depth ft-in (mm) 0-4 (111) 0-5 (116) 0-4 (103) 0-4 (108) 0-4 (108) 0-4 (94) 0-4 (99) 0-3 (86) 0-4 (91) 0-4 (91)

T Reach at Dump Height ft-in (mm) 3-6 (1069) 3-7 (195) 3-2 (959) 3-3 (985) 3-5 (1030) 3-8 (1118) 3-10 (1158) 3-3 (1008) 3-5 (1048) 3-7 (1093)

Reach Maximum (45° dump) ft-in (mm) 5-11 (1810) 6-2 (1874) 5-7 (1700) 5-9 (1764) 6-0 (1834) 5-11 (1793) 5-10 (1780) 5-5 (1663) 5-7 (1670) 5-9 (1740)

Operating Weight (includes 176 lb/80 kg operator and full fuel tank) lb (kg) 19,196 (8707) 19,370 (8786) 19,253 (8733) 19,418 (8808) 19,495 (8843) 19,575 (8879) 19,749 (8958) 19,632 (8905 ) 19,797 (8980) 19,872 (9014)

Assumes the machine is fitted with Michelin 15.5R25 XHA (L3) tires.

JCB WHEEL LOADER | 411 HT

4-cylinder wastegated turbo-charged, liquid cooled, direct injection diesel. Independent water pump and fan drives ensure maximum cooling efficiency and “clean-burn” combustion chamber provides minimum fuel consumption. A remote sump oil drain facility simplifies servicing.

Type Diesel 4 Stroke

Make JCB Dieselmax Tier III

Capacity in3 (l) 269 (4.4)

Bore in (mm) 4.06 (103)

Stroke in (mm) 5.2 (132)

Aspiration Turbocharged

Cylinders 4

Max Gross Power to SAE J1995/ISO 14396 hp (kW) @ 2200 rpm 100 (74.2)

Net Power to SAE J1349/EEC 80/1269 hp (kW) @ 2200 rpm 92.8 (69.2)

Max Torque lbf.ft (Nm) @ 1400 rpm 325 (440)

Emissions:-Complies with EPA Tier III – EU Stage 3A engine emission legislation.

ENGINE

Widely spaced four ram parallel geometry provides the combination of excellent visibility with high bucket torque characteristics throughout the working arc. Specification includes automatic bucket reset and lift arm kickout mechanisms. The pin, bush and sealing design on all pivot points provide extended maintenance intervals. Optional smooth ride system (SRS) reduces machine bounce on load/carry operations. Optional High Lift Loader specifically designed for optimum load over height.

LOADER

4 wheel drive, automatic smooth shift transmission electrically operated selector and gear change incorporating a speed inhibitor and modulation for smooth, responsive on-the-move direction and ratio changes. Single stage integral torque converter 4 forward and 3 reverse gears.

Type Smooth Shift Powershift

Make & Model ZF 4WG115

Torque Converter Stall Ratio 3.057 : 1

1st Gear mph (km/h) 3.33 (5.36)

2nd Gear mph (km/h) 7.75 (12.47)

3rd Gear mph (km/h) 17.09 (27.5)

4th Gear (forward only) mph (km/h) 23.30 (37.5)

TRANSMISSION

Priority steer hydraulic system with emergency steering. Piston pump meters flow through steer valve @ 2,538 lb/in2 (175 bar) to provide smooth low effort response. Steering angle ± 40°. Steer rams located high in the chassis fabrication to provide protection from damage. Adjustable steering column.

STEERING

A variety of tire options are available including:15.5 x 25 x 12 ply (L2). 15.5 x 25 x 12 ply (L3). 15.5R25 XTLA (L2). 15.5R25 GP2B (L2). 15.5R25 XHA (L2).

TIRES

Double gear pump with automatic unloader giving combination of speed and power on demand making efficient and economic use of available engine power. Main services are servo actuated from a single lever loader control. Accumulator back-up is available to control loader in the event of loss of pump pressure.

Pump Type Double Gear Pump

Pump 1 Max Flow gal/min (l/min) 13.3 (50.6)

Pump 1 Max Pressure lb/in2 (bar) 3190 (220)

Pump 2 Max Flow gal/min (l/min) 19.1 (72.6)

Pump 2 Max Pressure lb/in2 (bar) 2465 (170)

Hydraulic Cycle Times at Full Engine Revs Seconds

Arms Raise (full bucket) 5.0

Bucket Dump (full bucket) 1.1

Arms Lower (empty bucket) 3.7

Total Cycle 9.8

Ram Dimensions Bore Rod Closed Centers Stroke

Bucket Ram x2 in (mm) 3.1 (80) 2 (50) 59.1 (1502) 36.5 (928)

Lift Ram x2 in (mm) 3.5 (90) 2 (50) 43.6 (1107) 29.3 (743)

Steer Ram x2 in (mm) 2.4 (60) 1.2 (30) 24.4 (621) 12.3 (312)

LOADER HYDRAULICS

Hydraulic power assisted braking on all wheels. Dual circuit with accumulator back-up provide maximum safety under all conditions. Organic brake linings are environmentally acceptable. Parking brake, mechanical disc type operating on transmission output shaft.

BRAKES

AXLES

Type Epicyclic Hub Reduction

Make & Model JCB PD70 Front & Rear

Overall Axle Ratio 18.16 : 1

Rear Axle Oscillation 12.5°

JCB WHEEL LOADER | 411 HT

Resiliently mounted ROPS/FOPS structure (tested in accordance with ISO 3471-1 : 1986 / ISO 3449 : 1984). Deluxe operator environment combines ergonomically located controls with a high level of appointment and low internal noise levels. Entry/exit is via large rear hinged door and anti-slip steps. Excellent forward visibility is provided by a 3 section curved, laminated windscreen and low waistline. Extensive instrumentation includes electronic monitoring panel and display (EMS). Heating / ventilation provides balanced and filtered air distribution throughout the cab via a powerful 11 kW capacity heater. The unitary construction allows easy sealing and prevents ingress of dust. A transmission lock on the selector prevents inadvertent engagement and the loader controls can be isolated for safe road travel.

CAB

gal (l)

Hydraulic System 29 (110)

Fuel Tank 33 (125)

Engine Oil Sump 2.8 (10.7)

Transmission Oil System 7.1 (27)

Axle Oil (front) 6.6 (25)

Axle Oil (rear) 6.6 (25)

Engine Coolant System 5.7 (21.5)

SERVICE FILL CAPACITIES

An extensive range of attachments including pallet forks, crane jibs, high dumping buckets and timber grapples are available to fit directly or via the JCB quickhitch mounting.

ATTACHMENTS

Loader: Bucket reset mechanism, loader arm kickout mechanism, loader control isolator, single lever servo control, high torque true parallel lift geometry combines with excellent visibilty between the arms.

Engine: Air cleaner – 3 stage dry type – cyclonic with primary and safety elements, auto tensioner, cold start advance, fuel filters, fan guards.

Transmission: Single lever shift control, speed inhibitor, neutral start, disconnect on footbrake and loader lever, disconnect isolator switch, direction changes and kickdown on gear selector and loader control lever, air blast transmission cooler.

Axles: Epicyclic wheel hub reduction, fixed front, oscillating rear.

Brakes: Multi-plate wet disc brakes, organic linings, dual circuit hydraulic power assisted. Parking disc brake on transmission output shaft.

Hydraulics: Double gear pump with priority steer, emergency steer back-up, 2 spool loader circuit with accumulator support, 3rd spool auxiliary hydraulic circuit as standard. Hydraulic tank located in the rear chassis fabrication. Air blast cooler.

Steering: Adjustable steering column, “soft feel” steering wheel 5 turns lock to lock, resilient stops on max lock.

Cab: ROPS/FOPS safety structure, cigar lighter, ashtray, interior reading light, center mounted master warning light. Electronic monitoring panel with LCD message display. Two speed intermittent front windscreen wipe/wash and self park, single speed rear windscreen wipe/wash and self park. 3 speed heater/demisting with replaceable air filter, LH and RH opening windows, sun blind, internal rear view mirror, heated external mirrors, adjustable suspension seat with belt and headrest, operator storage facilities, laminated windscreen, loader control isolator, horn.

Electrical: Road lights front and rear, parking lights, front and rear working lights, reverse alarm and light, rear fog light, battery isolator, radio wiring and speakers, 55 amp alternator, rotating beacon.

Bodywork: Front fenders, side and rear access panels, flexible bottom step, full width rear counterweight, recovery hitch, lifting lugs.

STANDARD EQUIPMENT

Auxiliary 4th spool hydraulic service, air conditioning, limited slip differentials front/rear axles, additional counterweight, oil bath air cleaner, turbo 2 pre-cleaner, visibowl pre-cleaner, tooth guard, replaceable bucket wearparts, sealed alternator, epoxy coated radiator/coolers, smooth ride system (SRS), hydraulic quickhitch, rear fenders, high lift arms, reversing camera (color), auto greasing system, auxiliary control buttons on joystick, spark arrestor, 24 V to 12 V in cab converter, cab screen guards, additional front and rear cab mounted work lights, air suspension seat, front chassis apron mat, sun visor.

OPTIONAL EQUIPMENT

24 V negative ground system, 55 Amp alternator with 2 x 126 Amp hour low maintenance batteries. Isolator located in rear of machine. Ignition key start/stop and pre-heat cold start. Primary fuse box. Other electrical equipment includes quartz halogen, twin filament working lights, front/rear wash/wipe, heated rear screen, full road going lights, clock, gauge and warning light monitoring. Connectors to IP67 standard.

ELECTRICAL SYSTEM

System Voltage V 24

Alternator Output Ah 55

Battery Capacity Ah 2 x 110

JCB WHEEL LOADER | 411 HT

LOADER DIMENSIONS - FORK FRAME WITH FORKS

HIGH LIFT LOADER DIMENSIONS - FORK FRAME WITH FORKS

A

B

C

D

E

F

A

B

C

D

E

F

Assumes Michelin 15.5R25 XHA L3 Tires Parallel Fork Roll Back Fork

Fork Carriage Width ft-in (mm) 4-11 (1500) 4-11 (1500)

Length of Tines ft-in (mm) 4-0 (1220) 4-0 (1220)

A Reach at Ground Level ft-in (mm) 2-2 (662) 2-2 (669)

B Reach at Arms Horizontal ft-in (mm) 4-8 (1425) 4-8 (1432)

C Below Ground Level ft-in (mm) 0-1 (17) 0-1 (27)

D Arms, Horizontal Height ft-in (mm) 5-8 (1728) 5-8 (1718)

E Arms, Maximum Height ft-in (mm) 10-11 (3320) 10-10 (3310)

F Reach at Maximum Height ft-in (mm) 2-8 (813) 2-8 (820)

Payload** lb (kg) 6322 (2868) 6322 (2868)

Tipping Load Straight lb (kg) 9533 (4324) 9533 (4324)

Tipping Load Full Turn (40°) lb (kg) 8175 (3708) 8175 (3708)

Attachment Weight lb (kg) 970 (440) 970 (440)

**At the center-of-gravity distance 1 ft 8 in (500 mm). Based on 80% of full turn tipping load as defined by ISO 8313.Manual fork spacings at 50 mm increments. Fork section 4 in x 2 in (100 mm x 50 mm).

Assumes Michelin 15.5R25 XHA L3 Tires Parallel Fork Roll Back Fork

Fork Carriage Width ft-in (mm) 4-11 (1500) 4-11 (1500)

Length of Tines ft-in (mm) 4-0 (1220) 4-0 (1220)

A Reach at Ground Level ft-in (mm) 2-8 (801) 2-8 (808)

B Reach at Arms Horizontal ft-in (mm) 5-0 (1521) 5-0 (1528)

C Below Ground Level ft-in (mm) 0-1 (17) 0-1 (27)

D Arms, Horizontal Height ft-in (mm) 5-8 (1728) 5-8 (1718)

E Arms, Maximum Height ft-in (mm) 11-4 (3459) 11-4 (3449)

F Reach at Maximum Height ft-in (mm) 2-8 (815) 2-8 (822)

Payload** lb (kg) 6190 (2808) 6190 (2808)

Tipping Load Straight lb (kg) 9027 (4095) 9027 (4095)

Tipping Load Full Turn (40°) lb (kg) 7738 (3510) 7738 (3510)

Attachment Weight lb (kg) 970 (440) 970 (440)

**At the center-of-gravity distance 1 ft 8 in (500 mm). Based on 80% of full turn tipping load as defined by ISO 8313.Manual fork spacings at 50 mm increments. Fork section 4 in x 2 in (100 mm x 50 mm).

JCB WHEEL LOADER | 411 HT

BUCKET SELECTOR

BUCKET SELECTOR

1,350 1,680 2,020 2,360 2,700 3,030 3,370 3,700 4,040 4,380 (800) (1000) (1200) (1400) (1600) (1800) (2000) (2200) (2400) (2600)

Material Density lb/yd3 (kg/m3)

STANDARD ARM

2.2 (1.7)

1.8 (1.4)

1.5 (1.2)

Buck

et C

apac

ity y

d3 (m

3 ) 100%

115% 95%

Bucket Fill Factors

Loose Density Fill Factor

Material lb/yd3 kg/m3 %

Snow (fresh) 337 200 110

Peat (dry) 674 400 100

Sugar Beet 894 530 100

Coke (loose) 961 570 85

Barley 1012 600 85

Petroleum Coke 1146 680 85

Wheat 1231 730 85

Coal Bitumous 1290 765 100

Fertilizer (mixed) 1737 1030 85

Coal Anthracite 1764 1046 100

Earth (dry) (loose) 1939 1150 100

Nitrate Fertilizer 2180 1250 85

Loose Density Fill Factor

Material lb/yd3 kg/m3 %

Sodium Chloride (dry) (salt) 2192 1300 85

Cement Portland 2428 1440 100

Limestone (crushed) 2580 1530 100

Sand (dry) 2613 1550 100

Asphalt 2698 1600 100

Gravel (dry) 2782 1650 85

Clay (wet) 2832 1680 110

Sand (wet) 3187 1890 110

Fire Clay 3507 2080 100

Copper (concentrate) 3878 2300 85

Slate 4721 2800 100

Magnetite 5402 3204 100

JCB WHEEL LOADER | 411 HT

JCB Headquarters Savannah, 2000 Bamford Blvd, Savannah, GA 31322  Tel: (912) 447-2000  Fax: (912) 447-2299  www.jcb.com

JCB reserves the right to change design, materials and/or specifications without notice. Specifications are applicable to units sold in the United States and Canada. The  JCB logo is a registered trademark of  J C Bamford Excavators Ltd.

A GLOBAL COMMITMENT TO QUALITY

JCB’s total commitment to its products and customers has helped it grow from a one-man  

business into one of the world’s largest manufacturers of backhoe loaders, crawler  

excavators, wheeled excavators, telescopic handlers, wheeled loaders, dump trucks,  

rough terrain fork lifts, industrial fork lifts, mini/midi excavators, skid steer loaders and tractors.

By making constant and massive investments in the latest production technology, the 

JCB factories have become some of the most advanced in the world.

By leading the field in innovative research and design, extensive testing and stringent quality control, 

JCB machines have become renowned all over the world for performance, value and reliability.

And with an extensive dealer sales and service network in over 150 countries,  

we aim to deliver the best customer support in the industry.

Through setting the standards by which others are judged, JCB has  

become one of the world’s most impressive success stories.

DWUSA 2979 12/11