Jargon buster - sound insulation
-
Upload
susan-witterick -
Category
Engineering
-
view
52 -
download
5
Transcript of Jargon buster - sound insulation
SOUND INSULATION
DBX ACOUSTICS
SOUND INSULA T ION
JARGON BUSTE R
DBX ACOUSTICS
OV ERV IEWA QUICK
Airborne NoiseImpact NoiseAvoiding FlankingThe Difference Between Rw and Dw
SOUND INSULATION
DBX ACOUSTICS
BUILDING STYP E S OF SOUND INSULATION IN
There are two main types of noise that are of concern when it comes to sound insulation in buildings.
Airborne NoiseImpact Noise
SOUND INSULATION
DBX ACOUSTICS
NOIS EAIRBORNE
E XAMP LE S OF AIRBORNE NOISE
Someone's voice
Music from a loudspeaker
Sound from a television
Airborne noise is any unwanted noise that travels or transfers through the air. It is most relevant when constructing partitions between rooms.
This is defined as a variant of either Rw or Dw, and isusually specified as a minimum value of insulation which must be achieved.
SOUND INSULATION
DBX ACOUSTICS
SOUND INSULATION
NOIS EIMP ACT
Impact noise occurs when energy passes into a partition from an impact, and re-radiates as noise on the other side. The example of this you will likely be most familiar with is footsteps on a floor that can be heard in the room below - especially concerning in domestic situations. Impact is a form of structure-borne noise, which many of us have also experienced when neighbours decided to get the drill out and do some DIY too early on a Sunday morning! This is specified as a variant of Lw and, in contrast to airborne sound insulation, is specified as an upper limit which must not be exceeded.
DBX ACOUSTICS
SOUND INSULATION
INSULA T IONSOUND
Avoiding Flanking and The Difference Between Rw and Dw
DBX ACOUSTICS
SOUND INSULATION
SOUND F LANKINGAVOID ING
D UCTWORK
Ductwork passing from room to room may also prove an issue, but cross-talk attenuators (prefabricated sections of ductwork with acoustic lining) can be used to stop ducting acting like a “speaking tube”, and allowingspeech to transfer from room to room.
Flanking is sound that transfers from Room A to B through a route other than directly through the partition. This might include junctions of walls with ceilings or floors, if the partition isn’t properly detailed and sealed. It's also common for a hole to be drilled through the partition, for example for cables, then not be properly sealed, leading to excessive flanking.
Products like expanding foam won't stop noise from passing through; in any case, the key to sound insulation is mass. To stop sound flanking, small openings need to be properly stopped up with mineral wool and mastic. Larger openings may require a cover plate to perform as intended.
DBX ACOUSTICS
SOUND INSULATION
Rw and DwTHE D IFFE RE NCE BE TWE E N
RwThe laboratory stated value of the sound reduction index of a building. It can, for example, apply to walls, ceilings, floors, doors, windows, etc.
D wThe on-site measured values of the sound insulation. This is the target used to measure against in pre-completion testing.
Both Rw and Dw are ways of rating the performance of a partition in terms of Sound Insulation which must be achieved.
SOUND INSULATION
DBX ACOUSTICS
SOUND INSULATION?SO, YOU WANT TO ACHIEVE DECENT
FOLLOW THE " GOLDEN RULES"
Get some help on specification from an acoustic consultant - it's not just about the wall / floorBuild it properly - sound can be like water, it'll trickle through any holes you leaveThrow that expanding foam in the bin... Please?
DBX ACOUSTICS
SOUND INSULATION
NEED S OME A DVI CE?
WWW.DBXACOUSTICS .COM
WE'D BE HAPPY TO HELP