Jacket Spec Sheet By-Amit Singh
Transcript of Jacket Spec Sheet By-Amit Singh
SPECIFICATION SHEET OF JACKET
NATIONAL INSTITUTE OF FASHION TECHNOLOGY,NEW DELHI
Subject name:
AssignmentOn
SPEC SHEET OF JACKET
Submitted by :Amit Kr. Singh (01)
Anuj Kumar (02)Muneem Meena (22)
Ajad Pandey (11)
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
[M. F. Tech Sem-II]Batch-2008-10
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
RAW MATERIAL
FABRIC:
SHELL:
Contents: Cotton, nylon 3-ply
Construction: Warp = 154, Filling = 64
Yarns: Warp = single ply/70, Filling = 3-ply/70.
Weave: Plain
Weight: 4.0 ozs./sq. yd.
Warp stretch: 4%
Filling stretch: 4%
Dying: High pressure jet dyed
Finish: The face has a specialty napping process for cotton aesthetics.
REMOVABLE COLLAR LINER: 100% Polar Fleece®, 490 gm. weight.
LINING: Face and back is non woven light weight fabric. Interlining is 200 gm. Body and 100 gm sleeves.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
Product ID 07152930, MENS JACKET
Sent Date: 30th MARCH, 2009Packet Type: PrototypeBusiness Partner Name: xyz Pvt. Ltd
FRONT VIEW
BACK VIEW
PRODUCT OVERVIEWPRODUCT ID: 07152930PRODUCT NAME: JACKETSEASON: 2009, WINTER BUYER NAME: ABC PVT. LTD ADJACENCY: RTW-READY TO WEAR FABRIC: blended cotton/nylonDEPARTMENT: XYZ SOURCING ZONE DESIGN STRATEGY: INTERNAL DESIGNBRAND: JIN MAO GENDER: MALESET DATE: 30/03/2009 PACKET TYPE: PROTOTYPESENT DATE: 10TH DECEMBER 2008 BUSINESS PARTNER TYPE: XYZ PVT. LTD
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
SKETCH (FRONT)Season SS 09Brand JIN MAOItem MENS JACKETStyle MP 852 BView FRONTSample Size L
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
SKETCH (BACK)Season SS 09Brand JIN MAOItem MENS JACKETStyle MP 852 BView BackSample Size L
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
TABLE OF MEASUREMENT FOR SIZE SET
FRONT
S.No. PARAMETER LENGTH (INCHES) TOLERANCE (+/-)
1 Full length 26 12. Shoulder length 6.5 03. Shoulder drop 1.5 04. Across chest below 1” armhole 23 15. Arm hole 22.5 06. Sleeve length 22 17. Across hem 40 08. Front neck drop 6 09. Neck girth 20 010. Side seam 16 011. Sleeve hem 11.5 012. Collar smile 4 0
BACK
S.No. PARAMETER LENGTH (INCHES) TOLERANCE (+/-)
13. Center back length 26 114. Yoke length 20 115. Yoke width at armhole level 23 016. Yoke width at neck line level 7 0
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
CONSTRUCTIONAL DETAIL SHEET
LININGThere are two inter linings which is made of quilt and nonwoven fabric. In front, back consist of the non woven fabric and sleeve lining consist of the quilt.
FACINGIn front inside there is a facing of body fabric attached in front inside which has dimension as follow:
S.No. PARAMETER LENGTH (INCHES)
TOLERANCE (+/-)
17. Length 12 1
18. Length at zipper level 7 4/8 019. Length at neck line level 5 2/8 0
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
POCKET FRONT CHEST POCKETS: There are pocket on the front one is printed and other side without print, set-in pockets with flaps with 2.5” length & 5” width. The pocket opening shall be 5 ” wide and 6” deep there is a print on one pocket The pocket bag shall be made of
a good commercial polyester/cotton, non-pill pocketing
S.No. PARAMETER LENGTH (INCHES)
TOLERANCE (+/-)
20. Pocket (a) length (b) Width
65
.2
.221. Flap- (d) Length
(e)Width6
2.5.2.2
FRONT CROSS POCKETS: There shall be two lower, cross, welted hand warmer pockets set approximately 5.75” from the front zipper. The welts shall be 7 ½” tall and 7/8” wide and secured with a bar tack at each end. There shall be a cord set into the front edge of the welt. There shall be a hidden black, nylon coil closure under the welt. The pocket bag shall be made of a good commercial polyester/cotton, non-pill pocketing. The color of the bag shall be black. The pocket welt will be framed with a ¼” topstitch.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
INSIDE UTILITY POCKET: There shall be one set-in pocket on the left inside lining. This shall be a double-welted pocket. The functional pocket opening shall be a minimum of 6 ” and the pocket depth shall be a minimum of 8 ½” measured from the top to the bottom of the pocket bag. The pocket bag shall be made of a good commercial polyester/cotton, non-pill pocketing. The color of the bag shall be black.
WAIST BAND
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
WAISTBAND: The bottom of the jacket shall have a 2” side waistband from end to end. Approximately 4” from each zipper side shall be plain and interlined with a good, commercial grade non-woven interlining. On back side shall be secured with 1” wide Velcro
.
MOON PATCHThere is a moon patch on which main label attached.
S.No. PARAMETER LENGTH (INCHES) TOLERANCE (+/-)22. Length 3.5 .5
23. Width at Top 5 .524. Width at bottom 2.5 .3
FLAP ATTACTHED WITH VELCRO
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
S.No. PARAMETER LENGTH (INCHES) TOLERANCE (+/-)25. Length 3.5 .226. Width max. 1.5 027. Width min. 1.0 0
COLLAR
CUFF
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
TRIMS & ACCESSORY DETAIL SHEET
ZIPPER There shall be a #10 nylon, non-reflective non-freeze 1-way zipper from the bottom of the jacket to the bottom of collar. This shall be interlined with a good commercial grade non-woven interlining. There will be an inside storm fly on the right front measuring 1 ½” wide from the bottom of the waist to the bottom of the collar. This shall be interlined with a good commercial grade non-woven interlining.
SNAPSThere are metal snaps attached on cuffs and front pocket flaps. Total snaps are 6 two each on cuffs and one on flap.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
VELCROTwo Velcro secured with waist band in back side with loop. Velcro dimensions are as follows:
S.No. PARAMETER LENGTH (INCHES)
TOLERANCE (+/-)
28. Length 2.5 .1
29. Width 0.75 0
LABEL
LABELS: All labels will be permanent to withstand repeated cleanings for the life of the garment. The following labels shall be applied:
MAIN LABEL: There shall be a main label on both the main jacket and removable liner. This shall identify the manufacturer either by name & location, registered trademark.
CONTENTS/CARE/SIZE LABEL: There shall be an additional label on both the main jacket and removable liner clearly showing the fabric contents, laundering instructions and garment size.
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI
SPECIFICATION SHEET OF JACKET
SEAMING & SEWING THREAD
SEAMING: All main joining seams shall be overlock safety stitched and then topstitched with a ¼” stitch on the outside.
THREAD: All thread shall be poly-core. All main seams shall use a #40 thread, and the balance #60.
PRINITING Here on back side of garment a logo of S’OLIVE Company’s logo printed with rubber printing. One motif printed on front left side above the chest pocket. Chest pocket also printed with rubber printing.
IN FRONT IN BACK
AT POCKET
NATIONAL INSTITUTE OF FASHION TECHNOLOGY, NEW DELHI