J2 Physics 2008 Lasers & semiconductors prelim questions

14
1. Which of the following best describes the meaning of population inversion? A The incident photons’ frequency is the same as the frequency of the stimulated photons. B An atom in an excited state undergoes a transition to the ground state and emits a photon. C The number of electrons at a lower energy level exceeds the number of electrons at a higher energy level. D The number of electrons at a higher energy level exceeds the number of electrons at a lower energy level. ACJC 08P1Q37 __________________________________________________________________________________________ 2. Which of the characteristic below describes the energy band structure of a typical semiconductor? valence band energy gap / eV conduction band A completely filled 1 eV almost filled B completely filled 1 eV almost empty C partially filled 10 eV almost empty D partially filled 10 eV almost filled ACJC 08P1Q38 __________________________________________________________________________________________ 3. (a) (i) With reference to conduction electrons and holes, explain why electrons in solids are represented by energy bands, whereas those in isolated gas atoms are be represented by energy levels. [2] (ii) Using band theory, explain how p-type and n-type extrinsic semiconductors are produced from intrinsic semiconductors for better electrical conduction. Hint: You may draw relevant diagrams to help you in your explanations. [3] (iii) Fig 7 shows a p-type semiconductor placed in contact with another of n-type. 1. Explain how a depletion region is formed between the n- and p-type. Hint: You may draw relevant diagrams to help you in your explanations. [3] 2. Explain how the depletion layer acts as a rectifier. [2] ACJC 08P3Q7 __________________________________________________________________________________________

description

J2 Physics 2008 Lasers & semiconductors prelim questions

Transcript of J2 Physics 2008 Lasers & semiconductors prelim questions

Page 1: J2 Physics 2008 Lasers & semiconductors prelim questions

1. Which of the following best describes the meaning of population inversion?

A The incident photons’ frequency is the same as the frequency of the stimulated photons.

B An atom in an excited state undergoes a transition to the ground state and emits a photon.

C The number of electrons at a lower energy level exceeds the number of electrons at a higher

energy level.

D The number of electrons at a higher energy level exceeds the number of electrons at a lower

energy level.

ACJC 08P1Q37 __________________________________________________________________________________________ 2. Which of the characteristic below describes the energy band structure of a typical semiconductor?

valence band energy gap / eV conduction band

A completely filled 1 eV almost filled

B completely filled 1 eV almost empty

C partially filled 10 eV almost empty

D partially filled 10 eV almost filled

ACJC 08P1Q38 __________________________________________________________________________________________ 3. (a) (i) With reference to conduction electrons and holes, explain why electrons in solids are

represented by energy bands, whereas those in isolated gas atoms are be represented by energy levels. [2]

(ii) Using band theory, explain how p-type and n-type extrinsic semiconductors are

produced from intrinsic semiconductors for better electrical conduction. Hint: You may draw relevant diagrams to help you in your explanations. [3]

(iii) Fig 7 shows a p-type semiconductor placed in contact with another of n-type.

1. Explain how a depletion region is formed between the n- and p-type.

Hint: You may draw relevant diagrams to help you in your explanations. [3]

2. Explain how the depletion layer acts as a rectifier. [2]

ACJC 08P3Q7

__________________________________________________________________________________________

Page 2: J2 Physics 2008 Lasers & semiconductors prelim questions

4. In the action of a laser, population inversion refers to

A the rate of stimulated emission being smaller than the rate of absorption. B more atoms in a high energy state than in a lower one. C photons causing other photons of the same frequency to be emitted from excited atoms. D charged particles causing light to be emitted from excited atoms.

AJC 08P1Q37

__________________________________________________________________________________________ 5. The diagrams illustrate the conduction band (CB), forbidden band (FB), valence band (VB) and an

energy level of different materials.

Which diagram depicts a semiconductor doped with boron?

AJC 08P1Q38

__________________________________________________________________________________________ 6. Which of the following statements about a semiconductor diode in forward bias is incorrect?

A The applied potential difference from the source of e.m.f. opposes the junction potential. B Electrons and holes are urged away from the p-n junction. C The n-type material of the diode is connected to the negative terminal of the source of e.m.f.

D Electrons in the n- type side of the diode will cross steadily to the p- type side.

CJC 08P1Q39 __________________________________________________________________________________________ 7. Junjie tried to build a laser himself and failed for the hundredth time. Which of the following is not a

possible reason for failing to achieve lasing?

A Population inversion failed to take place. B The mirrors were misaligned such that stimulation emission did not occur. C The absence of a metastable state prevented stimulation emission from taking place. D The potential difference applied was too high and prevented spontaneous emission from

emitting the correct wavelength.

DHS 08P1Q38 _________________________________________________________________________________________ 8. (a) Explain why population inversion is important in lasers. [2]

(b) Light emitting diodes of different colours can be produced using semiconductor materials with a small band gap. A p-n junction is made using doped semiconductors to produce the light emitted by the diodes. (i) Describe how a band gap is formed in a semiconductor. [3]

(ii) Explain how doping affects the conduction properties of a p-type semiconductor. [3] (iii) Describe how a depletion region can be formed at a p-n junction. [2]

DHS 08P3Q4 _________________________________________________________________________________________

Page 3: J2 Physics 2008 Lasers & semiconductors prelim questions

9. (a) One property of a laser is that it can direct a large amount of energy to a very small spot. In one particular application, the laser emits a 3.0 mJ pulse in 1.0 ns, focused to a spot 8.0 × 10

-10

m2

in area. Calculate the power per unit area at the target. [2] (b) Using the ideas of population inversion and stimulated emission, explain how a laser could

deliver an intense and directed light beam. [4] HCI 08P2Q4

_________________________________________________________________________________________ 10. Solar cells are p-n junctions which can convert solar energy into electrical energy. The basic principle of

a solar cell can be summarized in two sentences: 1. Incident photons arriving at the depletion region are absorbed to generate electron-hole pairs

(EHP). 2. The electron-hole pairs generated in the depletion region are immediately swept by the internal

electric field from the depletion region into the neutral regions giving rise to a current through an external load.

(a) With the help of a clearly labelled energy band diagram, explain how a photon arriving

at the depletion region is able to generate an EHP. [3]

(b) Shade the region in Fig. 5 where the positive fixed ions reside. [1]

(c) Indicate using arrows in Fig. 5, the directions of the electric forces experienced by the electron-hole pair in the depletion region. [1]

(d) Hence deduce and indicate in Fig. 5 the direction of current through the external load.

[1]

HCI 08P3Q5 _________________________________________________________________________________________ 11. Which of the following statements about LASER is incorrect?

A Laser light is highly monochromatic. B Laser light is coherent and cannot be diffracted. C Laser light occurs when there is a population inversion between two atomic levels. D Laser light is due to stimulated emission.

IJC08P1Q37 _________________________________________________________________________________________

Page 4: J2 Physics 2008 Lasers & semiconductors prelim questions

12. At room temperature, the charge carriers inside a p-type semi-conductors are A holes only. B free electrons only. C positive ions. D both holes and free electrons.

IJC08P1Q38 _________________________________________________________________________________________

13. (a) (i) To produce laser light the following conditions must be satisfied: 1. The higher of two energy states must be metastable. [1] 2. A population inversion must exist between the two states. [1] Explain the meaning of the terms in italics.

(ii) An atom has two energy levels with a transition wavelength of 632.8 nm. There are 7.0 × 10

20 atoms pumped into the upper state with 4.0 × 10

20 atoms in the lower state.

Assuming that the emission of a single laser pulse stops when the two energy levels have equal numbers of atoms, how much energy could be released in a single laser pulse? [3]

(iii) The He-Ne laser emits light at a wavelength of 632.8 nm and has an output of 2.3 mW.

How many photons are emitted each minute by this laser when it is operating? [3]

(iv) The He-Ne laser with a beam aperture of diameter 12 cm is aimed at the moon 3.8 × 10

8 m away from the Earth. The laser beam will spread due to diffraction effects when

it emerges from the aperture. The angular location of the edge of the central diffraction is given by

where d is the diameter of the beam aperture. What is the diameter of the laser beam at the Moon’s surface? [4] [ Take sin θ ≈ tan θ, for small values of θ ]

(b) (i) With the help of suitable energy diagrams, explain the difference in electrical conductivity of metals and that of intrinsic semiconductors using the band theory of solids. [4]

(ii) The process of adding impurities, also known as doping can change the conductivity

of an intrinsic semiconductor. Describe using suitable diagrams, the formation of an n-type semiconductor. [4]

IJC08P3Q5 _________________________________________________________________________________________

Page 5: J2 Physics 2008 Lasers & semiconductors prelim questions

14. In a stimulated emission of a photon, as shown in Fig. 37.1 below, which of the following statements is

true?

A The electron in the excited state de-excites to the ground state in a random process and produce an photon of energy E1.

B An incident electron of energy E1 moves pass the excited atom. The atom then de-excites to give off an electron of energy E1. The incident electron is being absorbed by the atom.

C An incident photon of energy E1 moves pass the excited atom. The atom then de-excites to give off a photon of energy E1 which moves together with the incident photon with the same

phase.

D An incident electron of energy E1 moves pass the excited atom. The atom then de-excites to

give off a photon of energy E1 – E which moves together with the incident electron with the

same phase, where E is the kinetic energy of the incident electron.

JJC08P1Q37 _________________________________________________________________________________________

15. Which of the following statements about laser is false?

A The laser beam is monochromatic if there is only one laser transition.

B The laser beam is extremely unidirectional.

C The dispersion of a laser beam is due to diffraction around the edge of the aperture.

D All photons in the laser cavity are generated by stimulated emission.

JJC08P1Q38 _________________________________________________________________________________________

16. (a) A person’s vision may be improved significantly by having the corneal reshaped with a laser beam, in a procedure known as photorefractive keratectomy. The excimer laser used in these treatments produces UV radiation of wavelength 193 nm.

(i) What is the energy difference between the two levels that participate in the stimulated emission in the laser? [1]

(ii) How many photons from this laser are required to deliver 1.58 x 10-13

J of energy? [2]

(b) Electromagnetic radiation can promote an electron from the top of a nearly complete valence band to the bottom of an unfilled conduction band. The lowest frequency for this to be possible is 2.75 x 10

14 Hz for Si and 1.79 x 10

14 Hz for Ge at room temperature. Calculate the energy

gap between the valence and conduction bands for Si and Ge. [2]

(c) Explain how the depletion region in a p-n junction is formed. [2]

(d) (i) The tip of a STM probe is positioned at a distance d from a sample surface which has a work function energy of 6.0 eV. Find the value of d at which the tip-surface transmission coefficient T is 0.0001. [2]

(ii) An electron with de Broglie wavelength λ = 0.10 nm has an uncertainty in momentum of Δp = 6.6 × 10

−25 kg m s

−1. What is the uncertainty in the electron’s wavelength? [2]

JJC08P2Q5 _________________________________________________________________________________________

Page 6: J2 Physics 2008 Lasers & semiconductors prelim questions

17. Which statement about conduction of electricity in semiconductors is correct? A The presence of impurities in a semiconductor is used to decrease its resistance.

B In a semiconductor, there is a large energy gap between the conduction and valence bands.

C At low temperatures, free electrons are found both in the conduction band and in the valence band.

D In an intrinsic semiconductor, electrons travel in the same direction as the holes.

MJC08P1Q37 _________________________________________________________________________________________ 18. When a p-n junction is under reverse bias mode, the width of the depletion region will be increased.

Which of the following statements is true?

A The applied voltage moves the electrons from n-type region to p-type region.

B The applied voltage moves the holes from p-type region to n-type region.

C The applied voltage drives the electrons towards n-type region.

D The applied voltage drives the holes towards n-type region.

MJC08P1Q38 _________________________________________________________________________________________

19. Figure 6.1 illustrates the upper energy bands in two different classes of solid at absolute zero. The

shaded areas represent occupied electron energy levels.

(a) State the classes of solids for X and Y. [2] (b) At absolute zero, which solids, X or Y, will conduct electricity? Explain your choice using band

theory. [2] (c) At higher temperatures, solid X conducts electricity. Explain, using band theory, why this is so.

[3]

MJC08P2Q6 _________________________________________________________________________________________

20. In a piece of n-type silicon,

A the number of electrons in the valence band exceeds the number of holes in the

conduction band.

B the number of holes in the valence band is less than the number of electrons in the

conduction band.

C conduction is due to electrons only and the conduction and valence bands overlap.

D the impurity element with which silicon is doped has fewer valence electrons than

silicon.

NJC 08H2P1Q33

____

21. Which of the following statements is not related to laser production?

A Light amplification

B Stimulated emission

C Population inversion

D Electron deceleration

NJC 08H2P1Q34

Page 7: J2 Physics 2008 Lasers & semiconductors prelim questions

____ __________________

22. Electric currents in semiconductors are considered to be due to the motion of electrons and holes. Holes

are

A atomic vacancies.

B positively charged electrons.

C positive ions.

D electronic vacancies in atoms.

NJC 08H2P1Q34

___

23. When a beam of laser is shown on to a vertical slit as shown in Fig. 1, we can see a spot of light on the

screen as expected. As the slit is made narrower and narrower, the spot of light becomes wider and

wider in the X direction.

(a) By considering the laser beam as an electromagnetic wave, explain the phenomenon using wave

theory. [1]

(b) By considering the laser beam as consisting of a stream of photons, use Heisenberg Uncertainty

Principle to explain this phenomenon. [2]

(c) A laser beam of wavelength 635 nm is used in the above experiment. Find the momentum of a

photon in this laser beam. [2]

(d) If the width of the slit is 2.0 x 10-5

m, and the uncertainty x of the position of a photon passing

through the slit is approximately of the same value, calculate the uncertainty of the momentum px

of the photon using the following Heisenberg uncertainty equation: x

x p h . [2]

Image when slit is wide

Image when slit is made

narrower and narrower

X

Page 8: J2 Physics 2008 Lasers & semiconductors prelim questions

(e) Find sin using the results from (c) and (d). [1]

(f) In wave theory, the angle of such single slit diffraction experiment is given by

sin where a is the width of the slit

and is the wavelenght of the light.

a

Calculate the angle using this equation. [1]

(g) Comment on your answers obtained in (e) and (f). [1]

NJC 08H2P3Q4

___

24. (a) A three-level laser system is shown in Fig. 4.1, where E2 is the meta-stable state.

(i) Explain what is meant by meta-stable state. [1] (ii) Using Fig. 4.1, explain the action of a laser in terms of population inversion and stimulated

emission. [3] (iii) A four-level laser system is shown in Fig. 4.2. A student commented that this system is more

efficient than a three-level laser system.

px

p

Top view

Page 9: J2 Physics 2008 Lasers & semiconductors prelim questions

Explain why the student is correct. [2]

(b) (i) On Fig. 4.3, draw and label clearly the changes to the band diagrams for semiconductors due to n- and p-type doping. [2]

(ii) Using Fig. 4.3, explain how the n-type doping changes the conduction property of a semiconductor. [1]

(iii) What is the difference between n- and p-type semiconductors in terms of conduction?

[1]

PJC 08H2P3Q4

25. In comparing a semiconductor and an insulator, what are the relative dimensions of the energy gaps of the semiconductor and the insulator?

Semiconductor Insulator A Narrow Narrow B Narrow Wide C Wide Narrow D Wide Wide

SRJC 08H2P1Q37

Page 10: J2 Physics 2008 Lasers & semiconductors prelim questions

26. What is the overall electrical charge of the isolated n-type semiconductor? A Depending upon the balance of electrons, it will be positive or negative B Negative C Positive D Zero

SRJC 08H2P1Q38

27. In the production of laser light, atoms are excited to energy level E4 using light of wavelength 550 nm. After which it falls to its metastable state at energy level E3. Population inversion is achieved between energy levels E2 and E3. What is the wavelength, λ of the laser light emitted?

A 550 nm B 598 nm C 694 nm D 772 nm

RJC08H2P1Q37

28. Which of the following statements below on intrinsic semiconductors is true?

A The total current flow is the sum of both ‘hole’ and ‘electron’ currents.

B The valence band is completely filled and the conduction band is partially filled.

C There are more electrons in the conduction band than there are holes in the valence band.

D The valence band is completely filled and the conduction band is empty at room temperature.

RJC08H2P1Q38

29. (a) A laser constructed of the semiconductor Gallium Aluminium Arsenide (GaAlAs) can continuously deliver 5.0 mW of power at a wavelength of 0.80 μm.

(i) At what rate does it generate photons? [2] (ii) State any two important conditions required to produce a laser beam. [1]

(b) Beryllium (Be) is the most common dopant in GaAlAs.

Page 11: J2 Physics 2008 Lasers & semiconductors prelim questions

(i) With the help of the partial periodic table in Fig. 6, state if a n-type or p-type semiconductor will be obtained. [1]

(ii) Explain how such a doped semiconductor in (b)(i) increases the electrical conductivity of

GaAlAs. [3]

RJC08H2P2Q6

30. This question is about the charge carrier density of intrinsic silicon semiconductor. The density of energy states in a semiconductor near the bottom of a band is similar to that of a free electron gas but decreases back to zero at the top of a band. The energies at the top of the valence band and at the bottom of the conduction band are EV and EC respectively with a band gap energy EG of 1.1 eV. The

probability of occupation of these energy states is governed by Fermi-Dirac distribution. The density of energy states near the bottom of the conduction band is

(a) Sketch the density of states around the top of the valence band and the bottom of the conduction band. Indicate the position of the Fermi level in your sketch. [2]

(b) The average thermal energy of electrons is kT where k is Boltzmann constant and T is the

thermodynamic temperature. (i) Explain why the number of electrons in the conduction band for an intrinsic semiconductor at

room temperature is very low. [2] (ii) Show that at room temperature, the probability of occupation of the energy states in the

conduction band is [2]

(iii) On the sketch you have made in (a), sketch how the states in the conduction band will be

occupied. [1] (iv) Given that

show that the number density of electrons in the conduction band is

Page 12: J2 Physics 2008 Lasers & semiconductors prelim questions

[3]

(v) Determine the number density of electrons in the conduction band at room temperature of 300

K. [1]

RJC08H3Q5

31. In a p–n junction, free electrons near the junction in the n–type material diffuse across the junction into the p–type material. Diffusion occurs because

A the concentration of free electrons in n–type material is small and in p–type material is large. B the concentration of free electrons in n–type material is large and in p–type material is small. C the small potential across the depletion layer cause electrons to diffuse continuously across the

p–n junction.

D of different thermal agitation of atoms in the n–type and p–type material.

SAJC08H2P1Q32

32. (a) Explain how stimulated emission accounts for the properties of laser.

(b) Describe, with an appropriate energy level diagram, the production of lasers.

(c) A diode can be formed by joining a p-type semiconductor and an n-type semiconductor, to form a p-n junction. Explain the formation of the depletion layer in the diode and state the effect of reverse-bias condition on the depletion layer.

SRJC08H2P3Q4

33. (a) Give two reasons why a 1 W laser may appear brighter than a 10 W filament lamp. [2] (b) Draw and label the energy band diagram for an intrinsic semiconductor at room temperature, showing clearly how the bands might be filled. [2] (c) Use the band theory to explain why the addition of a small concentration of boron (Group III element) will decrease the resistivity of the semiconductor significantly. [2]

TJC08H2P2Q6

Page 13: J2 Physics 2008 Lasers & semiconductors prelim questions

34. Why is laser light monochromatic? A The atoms in the laser medium are in a state of population inversion. B The excited atoms in the laser medium are in a metastable state. C Photons which trigger off stimulated emission produce more photons of the same energy. D The photons produced by stimulated emission are reflected back by the use of reflecting

mirrors in the laser system. VJCH2P1Q36

35. Metals and semiconductors have different electrical properties because semiconductors have

A more valence electrons B a small energy band gap C fewer valence electrons D a higher atomic mass

VJCH2P1Q37

36. Which of the statements is correct for a p-type semiconductor? A There are excess holes in the valence band. B There are excess holes in the conduction band. C There are excess electrons in the conduction band.

D There are excess electrons in the valence band. VJCH2P1Q38

37. The addition of one part per million of arsenic will decrease the resistivity of silicon by a factor of 10

5.

This dopped silicon is an n-type semiconductor. (a) State two differences between p-type semiconductors and n-type semiconductor. [2] (b) Explain, in terms of band theory, how doping in an n-type semiconductor increases its conductivity.

[3] (c) Discuss with an aid of a diagram and using the idea of a depletion layer, how a p-n junction can act

as a rectifier. [4]

VJCH2P2Q5

Page 14: J2 Physics 2008 Lasers & semiconductors prelim questions

38. The diagram below shows the energy levels and electron transitions for the He-Ne laser, which produces a bright red light. The helium atoms are used to

excite the neon atoms into excited states by collision.

Identify the metastable state and the laser transition.

Metastable State Laser Transition

A E2, He E3,Ne to E2,Ne B E2, Ne E2,Ne to E1,Ne C E3, Ne E3,Ne to E2,Ne D E3, Ne E3,Ne to E1,Ne

YJC08H2P1Q37

39. Which of the following statements concerning a laser system is true?

A An external energy source is needed to create population inversion

because at thermal equilibrium, the electrons will occupy the lower energy states.

B High-end laser systems can produce perfectly collimated beams, i.e.

beams that would not spread.

C The laser beam achieves its brightness because of the two fully

reflecting mirrors placed at the ends of the tube containing the lasing substance.

D The laser beam produced is coherent and of a single wavelength

because of spontaneous emission. YJC08H2P1Q38

40. (c) Light from a laser is produced via stimulated emission, whereas light from a fluorescent tube is produced via spontaneous emission. Compare the light from these two sources in terms of phase difference and deduce the effect this has on the experimental setup for a double-slit interference experiment using laser light. [2]

YJC08H2P2Q3