J W S= 1#G k #J S S= a11 NgNS 7€¦ · J W S= 1#Gk #J S;S=;a11 NgNS 7 ¼ pÆ ª

REDUCTOCL IP™

DIRECT TO WALL

SYSTEM

Creating Peace and Quiet In Your Home

www.soundproofingstore.co.uk

[email protected]

01423 206208

https://www.soundproofingstore.co.uk/

Can be fitted by a good

DIY 'er , or tradesperson -

with experience of fitting

plasterboard

INSTALLATION

An innovative soundproofing solution

designed to isolate walls and reduce the

transference of sound vibration energy,

whilst also reducing airborne noise.

Outstanding performance against noisy

neighbours

The perfect solution for soundproofing

against medium to loud levels of noise

Suitable for use on solid or stud walls

Outperforms resilient bars by up to 7dB

Dual rubber for higher performance

Only 60mm build up from original walls

Wider furring channels for easier

plasterboard fixing

The thinnest direct to

wall isolation clip

system on the market

(60mm)

SAVES SPACE

The ProSound™ ReductoClip™ system offers the highest

level of soundproofing , with minimal loss of space

within your home (60mm).

Excellent performance

against noisy neighbours

PERFORMANCE

R E D U C T O C L I P ™ D I R E C T T O WA L L S Y S T E M


[email protected]

01423 206208

BENEFITS


Can be fitted by a good

DIY 'er , or tradesperson -

with experience of fitting

plasterboard

INSTALLATION


[email protected]

01423 206208

FEATURES

The thinnest direct to wall isolation clip system on the market (only 60mm

loss of space)

ReductoClips - able to withstand greater loads than standard clip systems,

resulting in 1/3 less clips and a more cost effective system

Reducto Furring Bar 2.4m - which outperforms standard resilient bar

constructions by up to 7dB

Acoustic grade plasterboard (15mm) - 50% denser than standard 12.5mm

plasterboard. With a mass of 12.6kg per m2 which reflects and converts high

levels of sound energy into heat

Tecsound SY 100 (self-adhesive) a specially developed thin 10kg per m2

soundproofing material

Acoustic grade (15mm) plasterboard - a further layer to increase airborne noise

blocking capabilities



PERFORMANCE

Solid Wall Build Up

Stud Wall Build Up

Airborne Performance: 55dB Airborne Performance: 60dB

Building Regulations Part E (UK) Requirements Airborne Performance

Separating Walls

Purpose built dwelling-houses and flats

(Higher than) 45dB

Dwelling-houses and flats formed by material

change of use

(Higher than) 43dB

Airborne Performance (The higher the figure the better)

Direct to solid wall

(Passes building regulations) 60mm loss of space from the wall

On a stud frame with acoustic mineral wool

insulation, with a layer of acoustic grade

plasterboard on the other side

(Passes building regulations) 60mm loss of space from the timber stud

60dB


[email protected]

01423 206208

Full ReductoClip system including; ReductoClips, furring channels, 25mm

acoustic mineral wool, two layers of 15mm acoustic grade plasterboard and

one layer of Tecsound SY100


55dB


Sharp trimming knife

Handsaw / Jigsaw

Screw fixings for attaching the clips to the wall (not provided)

Acoustic Sealant 900ml / Jumbo applicator gun

Spray Contact Adhesive

Please Note: The Plasterboards and Tecsound are heavy and we recommend two men forinstallation

TOOLS / ACCESSORIES REQUIRED


[email protected]

01423 206208

FIXINGS

The hole in the ReductoClip has a Diameter of 7.5mm for your fixing to go

through

Brick / Block / Concrete: We Recommend 5-6mm dia x 60mm long screws

with suitable plug ( 10—12 gauge if imperial)

Self tapping screws: For furring channel joins ( approx. 10 – 15mm)

First Layer of Plasterboard: plasterboard screws suitable for self drilling into a

metal furring's at 25mm in length

Second layer of Plasterboard: should be affixed using 50mm long self drilling

screws into the channel

*If your self tapping screws are struggling to pierce the furring bar, use a pilot

hole beforehand

Use Fasteners that will have a minimum of 120lbs pull out or sheer strength in

the wood, steel or concrete substrate.

DO NOT OVER TIGHTEN

LOAD SPECIFICATION

The ReductoClip is designed to carry a furring channel with one or more layers of acoustic

plasterboard attached.

The maximum design load capacity for the ReductoClip in sheer (wall application) or in

tension (ceiling application) is as follows. Design load calculations are based on tested

loading to failure where the furring channel deforms and pulls out.

Design Load Maximum for Wall or Ceiling Application

27kgs per ReductoClip when used with 0.6mm gauge furring bars



To affix the ReductoClips to the wall, secure ReductoClips with a single fastener on both

ends. For concrete, block or masonry use 6mm (12G) dia x 60mm long screws into

matching Rawlplug/Fischer fixing system.

Snap the Reducto furring channel into the ReductoClip by squeezing the furring bar. Or

hand slide ReductoClips to proper location on the furring channel. Fasten both ends of

the ReductoClip to secure the channel.


[email protected]

01423 206208

REDUCTOCLIP REQUIREMENTS

FURRING CHANNEL REQUIREMENTS

Minimum 0.6mm ga with hemmed edge. Standard – 16mm deep channel. Splice

furring channel with a 150mm overlap and secure overlapped pieces with wire or

screws per standard industry practice.

To affix the 15mm acoustic plasterboard to the furring channels; for one layer use

plasterboard screws suitable for self drilling into a metal stud system at 25mm in

length.

When using two layers of plasterboard the first layer should be affixed using a 25mm

long screw, the second layer should be affixed using 50mm long screw into the

channel.




[email protected]

01423 206208

REDUCTOCLIP POSITIONING DIAGRAM



3. Install 25mm Acoustic Mineral Wool between

bars and affix using Contact Spray Adhesive. No

need to cover the whole wall, there can be gaps (as

per the image opposite). Ensure the acoustic

mineral wool doesn't touch the furring bars. (It can

touch the clips).

Mark out your positions onto the wall, with

chalk, or a marker following the positioning

diagram. Then fix the clips at the appropriate

positions.. Maximum space between clips

1200mm (horizontally).

1.

Maximum space between furring bars (vertical)

clip positions 600mm.

Top row of clips should be a maximum of

150mm away from the ceiling.

Bottom row of clips show be a maximum of

100mm from the floor.

Top Tip: When the top and bottom ReductoClips

have been fixed onto the wall, install the

remaining clips at the same height spacings.


[email protected]

01423 206208

INSTALLATION


2. Attach the furring channels to the

ReductoClips making sure to overlap channels

by 150mm and securing with 4 self tapping

screws.

4. Tip! Before installing plasterboard layers, mark the locations of the

furring channels on the surrounding walls in chalk or pencil. This will

help you to locate the position of the furring channels later once the first

layer of plasterboard is on and channels are no longer visible.


7. Install Tecsound SY100. Tecsound is self

adhesive and requires no fixings or secondary

adhesive. Stick the Tecsound to the

plasterboard covering the entire wall, leaving

just the 5mm gap around the perimeter. TIP!

You may find it easier to cut the Tecsound into

smaller, more manageable pieces. Tecsound is

very sticky and is difficult to remove if stuck

down incorrectly.

n.b. Ensure the Tecsound is joined together

without any gaps.

5. Install first layer of 15mm acoustic plasterboard.

Start at the bottom in one corner. Raise the

plasterboard onto shims to keep the board 5mm off

the ground. Also make sure to leave a 5mm gap

between any boards and the surrounding walls and

ceiling. Secure the plasterboard to the furring bars

with dry wall screws. (Do not screw through to the

timber and short circuit the furring bars.)


[email protected]

01423 206208

Acoustic Sealant


6. (If not using an acoustic membrane

between plasterboards). Finish installing the

plasterboards. If necessary join two

plasterboards in line with the furring bars to

enable secure fixing of the plasterboard

where they join.

Fill in any small gaps with acoustic sealant.

Cut any holes as necessary for electrics.

8. Install second layer of 15mm acoustic

plasterboard as before but staggering the joins by

starting at the opposite side from where you started.

This should sandwich the Tecsound between the two

layers.



[email protected]

01423 206208

9. Finally remove the shims and fill the

gaps around the perimeter with

acoustic sealant along with any other

small gaps that may be in between

plasterboards.

10. Use acoustic putty pads inside

any electrical fittings to minimize the

weakness created by the hole. You

are now ready for standard

plasterboard finishes.


CROSS SECTION OF THE INSTALLED SYSTEM


Spacing of ReductoClips on the furring channel shall be a maximum of 1200mm

Spacing between Reducto furring channels shall be a maximum of 600mm

Use only the supplied Reducto furring channel

The seams of the very first layer of acoustic plasterboard should always align at the

centre of a furring channel (so two plasterboards meet on one furring channel)

The bottom row of ReductoClips with furring channels should be a maximum 100mm to

the centre of the channel from the floor. The top row should be within 150mm of the

ceiling

The first row of acoustic plasterboard sheets at the bottom of the wall shall be installed

with the long dimension supported on shims or Isolation Strip to keep the sheets off the

floor

Furring channels are installed horizontally, or parallel with the floor

All potential sound leaks; gaps around outlets, window, or door frames; pipe

penetrations and the like should be sealed with a non-hardening acoustic sealant

Do not overtighten the clips. The clip should feel secure, without moving and without

compressing the foam layer more than 1mm.


[email protected]

01423 206208

INSTALLATION SYNOPSIS

To watch a video of

the full installation

click here


https://youtu.be/lI2bdQZWyOE






Excellent

REDUCTOCLIP™ DIRECT TO WALL SYSYEM CUSTOMER TESTIMONIALS


[email protected]

01423 206208

Excellent product.

Achieved a significant

reduction in unwanted

noise. Everything in the

kit for the job. Very good

overall experience.

Really pleased with the result

of the ReductoClip system. It

has made a huge improvement

on the noise from next door.

I contacted them not knowing what i

needed to do, so i talked to them about

the issues and was advised on what to do.

Ordered the materials (they created a

shopping list right down to the gun’ for

the oversized sealer tubes). The goods

arrived the following week as promised

and I have installed the kit, barring the

sealer round the edges. It’s really effective!

Very pleased.

Can not fault product or service,

Friendly knowledgeable and

always answer any questions

promptly. I would highly

recommend soundproofing store,

it's made a huge difference in our

house.


Click to watch

https://youtu.be/VqHEVcBZt6M


https://youtu.be/VqHEVcBZt6M

If you are employing fitters, please do not schedule or start any installation work

until you have received your order

Delivery will be on a pallet and will be wheeled as close to your property as

possible. (Unfortunately our haulier cannot take the goods into your property)

Please note that our products have a great deal of mass, and will add weight to

your structure. You may need to check with a structural engineer to ensure

compatibility

PLEASE NOTE

SPECIFICATIONS

Thermal - thermal conductivity 0.24W/mK / thermal resistance:

15.0mm = 0.06.m2 K/W

Fire - fire rating 60 minutes


[email protected]

01423 206208

Weight - 35.7kg per m2

Size - 60mm build up from original walls



J W S= 1#G k #J S S= a11 NgNS 7€¦ · J W S= 1#Gk #J S;S=;a11 NgNS 7 ¼ pÆ ª

Documents

Transcript of J W S= 1#G k #J S S= a11 NgNS 7€¦ · J W S= 1#Gk #J S;S=;a11 NgNS 7 ¼ pÆ ª