HODEDAHITEM # HI71DR-G (MOP-SP) 7 DRAWER CHEST 2 people 90 mins 1 YR LTD 2 Box FRONT VIEW BACK VIEW...
Transcript of HODEDAHITEM # HI71DR-G (MOP-SP) 7 DRAWER CHEST 2 people 90 mins 1 YR LTD 2 Box FRONT VIEW BACK VIEW...
Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
HODEDAH ®
ITEM # HI71DR-G (MOP-SP)7 DRAWER CHEST
2 people
90 mins
1 YR LTD
2 Box
FRONT VIEW BACK VIEW
www.Hodedah.com 1| Page
Weight Capacity Per Drawer 25Ibs.
Product Dimensions: Height 48.39" x Width 47.24" x Depth 17.76"
Weight Capacity Per Shelf 25Ibs.
HODEDAH ®
www.Hodedah.com 2| Page
DO NOT RETURN PRODUCT TO THE STORE
Phone WebsiteEmail
Questions, need parts, we are here to help!
WARRANTY
WARNING
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
Mon - Fri | 9:30 am to 5pm EST Send us an email
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
Visit our website to open a case
1 - 855 - HODEDAH
1 - 855 - 463 -3324
[email protected] www.Hodedah.com
· This product contains small parts, keep away from children.
· This product contains plastic bags, keep away from children.
· Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
· Never allow children to climb or hang on drawers, shelves and doors.
· Never open more than one drawer at a time.
· The use of tip-over restraints may reduce but not eliminate the risk of tip-over.
HODEDAH ®
www.Hodedah.com 3| Page
Product Care and Maintenance
Let's get started…
· Never open more than one drawer at a time.
· The use of tip-over restranits may reduce but not eliminate the risk of tip-over.
· Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
· Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
· Work in a spacious level area, preferably carpet, near the place the unit will be used.
· DO NO USE power tools to assemble your furniture, it will strip and damage parts.
· Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Helpful hints, read before beginning assembly
Assembly Tools Required (not supplied)
· Wipe clean with dry soft cloth, never use chemicals or cleaning products they will
damage the finish.
· Avoid placing your furniture in direct sunlight, as sunlight causes fading.
· Never push, drag or pull your furniture, to move to a new location carefully with
two or more people carry the unit to its new location.
· Avoid extreme changes in temperature by arranging furniture away from radiators,
heat and air vents and air conditioning units.
Hammer Phillips Screwdriver No Power Tools NeededTape Measure
HODEDAH ®
www.Hodedah.com 4| Page
Hardware List
1
QTY
Screw M6 x 40mm
20 Pcs
Pvc Cap
2
QTY
Screw M4 x 32mm
66 Pcs
3
QTY
Screw M3.5 x 14mm
72 Pcs
QTY
8 Sets
6
QTY
Pvc Dowel
33 Pcs
7
QTY
8
QTY
Nail
170 Pcs
9
QTY
Allen Key
1 Pc
10
QTY
11
QTY
Hinges
12
QTY
Lock
Pvc Cap
Mini Fix
20 Pcs
8 Pcs
5
*For # 15 Drawer Slides
8 Pcs
Shelf Support
13
QTY
16
QTY
H-Profile
17
QTY
V-Bracket
28 Pcs
Screw M6.2 x 10mm
1 Pc
*For # 14 Drawer Slides
6 Pcs
Screw M 10 X 1/2 MM
3 Pcs
A
IM
3 Pcs
18
QTY
2 Pcs
Hanging Rod
1 Pc
19
(separate from
hardware pack)
Anti-Tip Kit
QTY
1 PK
HODEDAH ®
www.Hodedah.com 5| Page
Accessories
4
QTY
Handle8 Pcs
Screw M4 X 20mm
16 Pcs
14
15
Drawer Slide - A
*Fix On Side Panels
QTY
7 Sets
QTY
7 Sets
*Fix On Side Panels Q & R
Drawer Slide - B
Important
1. Before you throw the package, please use the Check Box to identify the parts
and hardware to ensure that you have everything you need.
2. Check and measure the bolts before applying them to parts.
3. Do not completely tighten all hardware until the entire assembly is complete,
unless indicated otherwise.
* Fix On Drawer Side Panels Ⓠ
* Fix On Drawer Side Panels Ⓡ
* Fix On Side & Stand Panels Ⓐ , Ⓗ
* Fix On Stand Panels Ⓗ , Ⓘ A , H & I
HODEDAH ®
www.Hodedah.com 6| Page
A
QTY
1 Pc
B
QTY
C
QTY
1 Pc
D
QTY
1 Pc
E
QTY
F
QTY
1 Pc 1 Pc
G
QTY
H
QTY
I
QTY
Parts List
J
QTY
K
QTY QTY
M
QTY
3 Pcs
L
Divider Panel
181x 413 x 15mm
Back Strengthening Panel
773 x 76 x 15mm
Kick Panel
1165 x 89 x 15mm
Right Side Panel
1200x 413 x 15mm
Strengthening Panel -Front
773 x 76 x 15mm
Front Strengthening Panel
773 x 76 x 15mm
Left Side Panel
1200x 413 x 15mm
Partition Panel
376x 340 x 15mm
Stand Panel
1095.5x 412 x 15mm
Strengthening Panel -Back
773 x 76 x 15mm
Bottom Panel
1165 x 412 x 15mm
Top Panel
1200 x 445 x 30mm
Back Panels
1140 x 397 x 3mm
1 Pc
1 Pc 1 Pc 1 Pc
N
QTY
Left Drawer Front Panel
-Small Drawer
394 x 180 x 15mm
O
QTY
Right Drawer Front Panel
-Small Drawer
394 x 180 x 15mm
1 Pcs1 Pc
1 Pc 1 Pc
1 Pc
HODEDAH ®
www.Hodedah.com 7| Page
P
QTY
Q
QTY
R
QTY
S
QTY
T
QTY
U
QTY
V
QTY
W
QTY
X
QTY
Parts List
Y
QTY
Drawer Base
Supporting Panels
394 x 51 x 15 mm
Drawer Base Panels-Small
Drawers
353x 394 x 3mm
Drawer - Left Side Panels
394 x 116 x 15mm
Drawer Base Panels -Big
Drawers
746 x 394 x 3mm
Drawer End Panels -Small
Drawers
324 x 111 x 15mm
D rawer Front Panels -Big
Drawers
793 x 180 x 15mm
Adjust Panel
376x 340 x 15mm
Door Panels
1106 x 394 x 15 mm
Drawer End Panels -Big
Drawers
714 x 111 x 15mm
Drawer - Right Side
Panels
394 x 116 x 15mm
2 Pcs
5 Pcs
2 Pcs
5 Pcs 7 Pcs
2 Pcs
5 Pcs
7 Pcs
5 Pcs
1 Pc
HODEDAH ®
www.Hodedah.com 8| Page
13
13
13
6
6
6
6
6
6
5
5
5
5
5
5
3
10
11
3
10
11
3
10
11
10
11
3
P
A
N
E
L
A
P
A
N
E
L
K
17
3
5
5
5
5
17
3
HODEDAH ®
www.Hodedah.com 9| Page
Pre - Assembly
5
5
Screw M6.2 x 10mm
24 Pcs.
13
3
5
Pvc Dowel
8 Pcs.
Screw M3.5 x 14mm
22 Pcs.
17
V-BRACKET
2 Pcs.
11
HINGES
3 Pcs.
10
SCREW M 10 X 1/2 MM
6 Pcs.
Mini Fix
6 Pcs.
6
SHELF SUPPORT
8 Pcs.
9
9
P
A
N
E
L
I
9
9
9
9
9
9
9
Insert the mini fix ⑥ (nuts) with the
cross arrow mark facing upward and
aim to panel A, I & K 's top thru
holes. (As shown)
Place the drawer slide A ⑭ onto the 2 holes area
shown at left side panel A and I. Then tighten it
with 2 screws ⑬ and 1 screw ③. Do the same for
the 5 other slide A ⑭.
Insert pvc dowels ⑤,
into 8 non thru holes
as shown using
hammer to gently tap
them in.
Tighten
V-brackets ⑰ on
panels I and K as
shown by using 2
screws ③.
Place Hinges ⑪ at the
panel K as shown.
Then tighten the hinges ⑪
with 2 screws ⑩ and 2
screws ③.
1
2
3
4
5
6
13
3
14
14
3
RIGHT VIEW
5
5
5
5
14
14
13
13
13
P
A
N
E
L
H
P
A
N
E
L
D
P
A
N
E
L
E
P
A
N
E
L
F
P
A
N
E
L
G
5
5
5
5
5
5
5
5
5
5
5
5
P
A
N
E
L
J
5
5
5
P
A
N
E
L
C
5
HODEDAH ®
www.Hodedah.com 10| Page
Pre - Assembly
Screw M6.2 x 10mm
4 Pcs.
13
5
5
5
P
A
N
E
L
B
5
5
P
A
N
E
L
L
6
6
6
6
6
6
6
6
LEFT VIEW
13
13
14
13
5
14
5
6
6
5
5
Mini Fix
2 Pcs.
6
6
Mini Fix
8 Pcs.
Pvc Dowel
25 Pcs.
5
Insert pvc dowels ⑤ to
both end of the panels
B, C, D, E, F, G &
J as shown.
Using hammer to gently
tap them in.
Insert mini fix ⑥ (nuts) with the cross arrow
mark facing upward and aim to the panel H 's top
thru holes. (As shown)
Place a drawer slide A ⑭ onto the 2
holes area shown at left side of panel H.
Then tighten the drawer slide A ⑭
with 2 screws ⑬ and 1 screw ③ .
Insert, push down and tighten mini fix
screw ⑥, to the hole as shown, 8pcs.
Insert pvc dowels ⑤ to edge of the
panel H 's non-thru hole as shown.
Using hammer to gently tap them in.
3
3
3
Screw M3.5 x 14mm
2 Pcs.
3
3
HODEDAH ®
www.Hodedah.com 11| Page
Assembly Of Small Drawers : 2 DRAWERS
Nail
20 Pcs.
7
3
Screw M3.5 x 14mm
12 Pcs.
Lock
2 Sets.
12
R
2
2
2
2
2
2
2
2
Q
S
N & O
Q
R
S
T
N & O
3
3
3
3
3
15
153
7
(2)
COMPLETED
(4)
Q
R
S
Q
N & O
(3)
Q S
12
Q
R
S
N & O
T
12
4
4
Screw M4 x 32mm
16 Pcs.
2
x2
x2
x2
x2
A
IM
-Place panel Q and panel R on each side of panel N & O as shown.
-Then, tighten screw ② to panel Q and panel R 's lower thru holes
to fix them onto panel N & O.
-Next tighten screw ② to panel Q and panel R 's upper thru holes
to fix up to the panel S.
-Flip drawer over with bottom side down, disassemble the lock ⑫ into 5 parts as shown,then install the lock ⑫
by inserting the lock ⑫ 's cylinder into middle thru hole of panel N & O, then fix the lock up.
-Tighten 2 screw ④ from inner side of panel N & O into the handle ④ holes.
Handle Screw
M4 x 20mm
4 Pcs.
4
Handle
2 Pcs.
4
-Flip drawer with bottom side up, place panel T onto the
drawer and align properly. Then nail the nails provided
with hammer on the border of panel T as shown.The gap
between 2 nails should be about 100mm.
-After that, place drawer slide B ⑮ with the small white
roller facing outward and with other end tip touching
panel N & O onto each bottom side (angle) edge of
panel R and panel Q. Then tighten 3 screws ③ on each
drawer slide B ⑮ (as shown).
(1)
HODEDAH ®
www.Hodedah.com 12| Page
Assembly Of Big Drawers : 5 DRAWERS
Nail
80 Pcs.
7
3
Screw M3.5 x 14mm
30 Pcs.
Handle Screw
M4 x 20mm
10 Pcs.
4
Screw M4 x 32mm
50 Pcs.
2
Handle
5 Pcs.
4
(3)
Q
R
U
P
V
4
4
(4)
Q
R
U
P
V
COMPLETED
x5
x5
x5
x5
Q
R
U
P
V
W
3
3
3
3
3
3
15
15
7
2
2
(2)
2
2
2
2
2
2
2
2
(1)
Q
R
U
P
-Place panel Q and
panel R on each side of
panel P as shown.
-Then, tighten screw ②
to panel Q and panel R
's lower thru
holes to fix them onto
panel P.
-Next tighten screw ②
to panel Q and panel R
's upper thru
holes to fix up to the
panel U.
-Flip drawer with bottom
side up, place panel V
onto the drawer
and align properly. Then
nail the nails provided
with hammer on the
border of panel V as
shown.The gap between
2 nails should be about
100mm.
-After that, place a
drawer slide B ⑮ with
the small white roller
facing outward and with
other end tip touching
panel P onto
each bottom side
(angle) edge of panel R
and panel Q. Then
tighten 3 screws ③ on
each drawer slide B ⑮
(as shown).
-Put drawer supporting
W onto middle of panel
V, then tighten
screw ② to drawer
supporting W 's thru
hole to fix it onto
panel V / panel P
(inner panel) / panel U.
-Flip the drawer over.
-Tighten 2 screw ④
from inner side of
panel P into the
handle ④ holes.
HODEDAH ®
www.Hodedah.com 13| Page
Step 1
Screw
M 6 x 40mm
6 Pcs.
1
Allen Key
1 Pc.
8
1
8
1
1
1
1
1
A
F
G
E
D
B
C
8
8
8
8
8
CAUTIONS : When inserting the PVC Dowels to non-thru holes, don't push to hard. Otherwise, the side
panels ( A, I & K ) may be damaged.
* Fix Panel B onto Panel C by inserting the dowel onto the non-thru
holes at Panel C as shown.
* Fix Panel B,C,D,E,F,G onto Panel A by inserting the (Left)
dowels onto the non-thru holes at Panel A.
* Using allen key ⑧ to tighten screw ① from the 6 thru holes
of panel A.
HODEDAH ®
www.Hodedah.com 14| Page
Step 2
Screw
M 6 x 40mm
8 Pcs.
1
Allen Key
1 Pc.
8
A
B
C
D
G
F
E
H
I
1
1
1
1
8
1
1
1
1
8
8
8
8
8
8
8
CAUTIONS : When inserting the PVC Dowels to non-thru holes, don't push to hard. Otherwise, the side
panels ( A, I & K ) may be damaged.
* Fix Panel B,C,D,E,F,G onto Panel I by inserting the (Right) dowels onto the non-thru holes at Panel I.
*Place Panel H (with drawer slide A ⑭ downward and the small white roller facing frontward) onto panel
G and panel F by inserting the (down) dowels onto non-thru holes at bottom area of panel H. Using allen
key ⑧ to tighten the 2 screw ① from the middle thru hole of panel G and Panel F.
* Using allen key ⑧ to tighten screw ① from the 4 thru holes of panel H.
HODEDAH ®
www.Hodedah.com 15| Page
Step 3
Screw
M 6 x 40mm
6 Pcs.
Allen Key
1 Pc.
8
A
K
I
H
F
G
D
E
B
C
J
1
1
1
8
8
8
8
8
8
1
1
1
CAUTIONS : When inserting the PVC Dowels to non-thru holes, don't push to hard. Otherwise, the side
panels ( A, I & K ) may be damaged.
* Fix Panel J onto Panel I by inserting the (Left) dowels onto the non-thru holes at
Panel I.
* Using allen key ⑧ to tighten screw ① from the 2 thru holes of panel I.
* Fix panel K onto panel J, B and C by inserting the (right) dowel onto the non-thru
hole at panel K.
* Using allen key ⑧ to tighten screw ② from 4 thru holes of panel K.
8
HODEDAH ®
www.Hodedah.com 16| Page
Step 4
A
H
6
6
F
G
6
6
6
6
6
6
A
K
I
H
F
G
E
D
C
B
J
L
Dowel / Mini Fix Installation
Place and fix panel
L onto panel A,
panel H, panel I
and panel K, and
align properly by
inserting
the 8 (down) mini
fix screws ⑥ onto
the L-thru holes at
top edge of panel
A, H, I and K. At
the same time,
pushing and light
tapping of panel L
downward to have
panel A, panel H,
panel I and panel K
's upside dowel
going onto panel L
's non-thru holes.
Mini Fix Cap
8 Pcs.
6
*Then, tighten mini
fix ⑥ clockwise
to lock the mini fix
up, for
tightening panel L
up. Cover 8 mini
fix caps provided
by pushing the
cover 's stem onto
the hole of mini
fix nut on upper
side of panel A, H,
I and K.
HODEDAH ®
www.Hodedah.com 17| Page
Step 5
8
Nail
44 Pcs.
A
I
K
M
M
M
F
H
L
G
E
C
B
Back View8
16
H-PROFILE
1 Pc.
16
* Lay the chest at face down position, Place the 3 back Panels M onto
the back of the main unit, and join the 2 panel M togather with H-profile
by slotting one side each of panel M into the track of H-profile. Then align
them properly for nailing.
* Then use hammer to nail the nails one by one and at center of
4 side edges. Gap between 2 nails should be about 100mm for all.
HODEDAH ®
www.Hodedah.com 18| Page
Step 6
1
L
H
Y
10
A
I
G
E
D
C
B
J
Y
K
1
1
1
1
1
1
1
1
Screw Cap
1
* Then take the adjusting panel Y
and place it inside the right
compartment by putting it on top
the 4 shelf support as shown.
* Lift up the main unit carefully and let it stand up properly.
* Cover all the screw ① 's head with the pvc cap provided by
pushing the cover's stem onto the hole of screw head one by
one for all screws.
HODEDAH ®
www.Hodedah.com 19| Page
Step 7
12
Lock
1 Set.
A
IM
11
HINGERS
3 Pcs.
Handle Screw
M4 x 20mm
2 Pcs.
4
12
3
11
X
4
4
Handle
1 Pc.
4
Screw M3.5 x 14mm
6 Pcs.
3
* Insert Hinges ⑪ into door panel X 's non-thru hole as shown, then tighten screw ③
through hinges ⑪ 's thru hole.
-Disassemble the lock ⑫ into 5 parts as shown,then install the lock
⑫ by insert the lock ⑫ 's cylinder into middle thru hole of panel X,
then fix the lock up.
-Tighten 2 screw ④ from inner side of panel X into the handle
④ holes.
HODEDAH ®
www.Hodedah.com 20| Page
Step 8
A
B
J
L
Y
K
Y
C
A
d
ju
s
t
X
N
O
P
P
P
P
P
18
18
HANGING ROD
1 Pc.
* You can align the door panel X by tightening and losening the
screw as shown.
* Place hanging rod onto both panels I and K 's
V-bracket.
HODEDAH ®
www.Hodedah.com
b
TP 6#x5/8'' Screw
2 Pcs.
Mounting bracket
4 Pcs.
d
Restraint strap
2 Pcs.
· Attach the mounting bracket a to the furniture in the
solid part below the top panel a few inches away from the
side of the unit.
· Screw b through the smallest hole of a .
FITTING OF ANTI-TIP SAFETY STRAP
STEP 1:
STEP 2:
· Locate a stud in the wall
behind the unit,does not
have to be centered.
· Place the other mounting
bracket a on the wall
stud 2 inches below the
mounting bracket
secured to the back of
your unit.
· Attach to the wall stud
using c through the
smaller hole of a .
· Repeat the same step a few inches away from
the other side of the unit.
· Place the furniture into position so both mounting
brackets are vertically in line.
· Lace the end of the restraint strap through the
larger holes in each mounting bracket.
· Secure the straps and lock into place.
STEP 3:
TP 8#x2'' Screw
2 Pcs.
BACK SIDE OF
TOP PANEL
WALL
a c
FURNITURE
21| Page
HODEDAH ®
www.Hodedah.com 22| Page
Completion
In the interest of our environment please dispose of all packaging thoughtfully.
* Take all drawers (5 big and 2 small), and slide them (the white rollers at drawer
slide at both side of drawers are to go into the track of the slides at each side
panel.) all the way gently, one drawer by one drawer starting from bottom one.
Enjoy & Thank you for purchasing from Hodedah!