ISO/IEC 17025:2017 GROUP GODREJ & BOYCE MFG. CO ...GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP...
Transcript of ISO/IEC 17025:2017 GROUP GODREJ & BOYCE MFG. CO ...GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP...
GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORSGROUP
has been assessed and accredited in accordance with the standard
ISO/IEC 17025:2017''General Requirements for the Competence of Testing &
Calibration Laboratories''for its facilities at
CALIBRATION & INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
in the field of
CALIBRATIONCertificate Number: CC-2634
Issue Date: 28/03/2020 Valid Until: 27/03/2022
This certificate remains valid for the Scope of Accreditation as specified in the annexure subject to continuedsatisfactory compliance to the above standard & the relevant requirements of NABL.
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)
Signed for and on behalf of NABL
N. VenkateswaranChief Executive Officer
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 1 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
Permanent Facility
1
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
3 Phase ActiveEnergy (50Hz) (60Vto 240V)
Using 3 Phase PowerTesting Instrumentby Comparison
AC Current(0.1 to5A) @UPF 0.1%
2
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to10kHz)
Using 5790A ACMeasurementStandard andA40/A40A Shunts byAC/DC TransferMethod
2 mA to 20 A 0.023 % to 0.06 %
3
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to1kHz)
Using 8508A DMMby Direct Method 10 µA to 200 mA 0.3 % to 0.05 %
4
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to1kHz)
Using 8508A DMMby Direct Method 2 A to 20 A 0.07 % to 0.13 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 2 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
5
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to1kHz)
Using 8508A DMMby Direct Method 200 mA to 2 A 0.05 % to 0.07 %
6
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (50Hz)Using HC 3100Precision PowerTesting Instrumentby Direct Method
20 A to 100 A 0.3 % to 0.1 %
7
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.12 W to 0.72 kW(0.1 PF) 3.35 % to 0.4 %
8
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.24 W to 1.44 kW(0.2 PF) 2.92 % to 0.24 %
9
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.48 W to 2.88 kW(0.4 PF) 2.92 % to 0.16 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 3 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
10
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.72 W to 4.32 kW(0.6 PF) 2.92 % to 0.13 %
11
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.96 W to 5.76 kW(0.8 PF) 2.92 % to 0.12 %
12
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
1.2 W to 7.2 kW(UPF) 2.92 % to 0.08 %
13
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
1 mV to 20 mV 0.72 % to 0.013 %
14
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 mV to 200 mV 0.017 % to 0.004 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 4 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
15
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 V to 60 V 0.008 % to 0.0035 %
16
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
200 mV to 20 V 0.008 % to 0.003 %
17
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to100kHz)
Using 5790A ACMeasurementStandard by DirectMethod
60 V to 600 V 0.0035 % to 0.06 %
18
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to1MHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 mV to 200 mV 0.013 % to 0.25 %
19
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to1MHz)
Using 5790A ACMeasurementStandard by DirectMethod
200 mV to 20 V 0.003 % to 0.13 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 5 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
20
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to1MHz)
Using 5790A ACMeasurementStandard by DirectMethod
6 mV to 20 mV 0.09 % to 0.34 %
21
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to20kHz)
Using 5790A ACMeasurementStandard by DirectMethod
600 V to 1000 V 0.0038 % to 0.01 %
22
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to300kHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 V to 60 V 0.003 % to 0.02 %
23
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (40Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
60 V to 1000 V 0.008 % to 0.004 %
24
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (HighVoltage)
Using HV Dividerwith KV Meter byDirect Method:
1 kV to 20kV 1.8% to 2%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 6 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
25
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Capacitance (100Hz)Using LCR Meter43100 by DirectMethod
10 µF to 100 µF 0.12 % to 0.5 %
26
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Capacitance (1kHz)Using LCR Meter43100 by DirectMethod
1 pF to 1 mF 0.68 % to 0.17 %
27
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Inductance (1kHz)Using LCR Meter43100 by DirectMethod
100 µH to 10 H 0.32 % to 0.17 %
28
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Oscilloscope -Bandwidth
Using 5502ACalibrator by DirectMethod
Up to 600 MHz 4%
29
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Phase AngleUsing Phase AngleMeter by DirectMethod
0 to 120 ° 1.11 ° to 0.61 °
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 7 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
30
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Phase AngleUsing Phase AngleMeter by DirectMethod
120 ° to 360 ° 0.61 ° to 1.11 °
31
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Power FactorUsing PowerAnalyser WT3000 byDirect Method
0.1 to UPF 0.03PF
32
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Power Single Phase(50Hz) (60V to240V)
Using 3 Phase PowerTesting Instrumentby Comparison
1 A to 100 A 0.1%
33
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method 1 m ohm to 1 ohm 0.61 % to 0.006 %
34
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method 1 ohm to 10 ohm 0.006 % to 0.0013 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 8 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
35
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method
10 M ohm to 100 Mohm 0.0031 % to 0.02 %
36
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method 10 ohm to 10 M ohm 0.0013 % to 0.0031
%
37
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method
100 M ohm to 10 Gohm 0.02 % to 0.23 %
38
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
RF Power (WithoutVSWR) (1MHz to1GHz)
Using RFMillivoltmeter URV55by Direct Method
-30 dBm to 15 dBm 0.25 dBm to 1.3dBm
39
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (10Hz to10kHz)
Using 5502ACalibrator by DirectMethod
33 mA to 3 A 0.582 % to 2 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 9 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
40
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
10 µA to 200 mA 0.8 % to 0.06 %
41
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (1kHz to10kHz)
Using 5720ACalibrator by DirectMethod
20 mA to 200 mA 0.06 % to 0.133 %
42
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (1kHz to5kHz)
Using 5502ACalibrator by DirectMethod
2 A to 20 A 0.5 % to 3.5 %
43
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (40Hz to10kHz)
Using 5720ACalibrator by DirectMethod
200 mA to 2 A 0.025 % to 1.7 %
44
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (50Hz to1kHz)
Using 5720ACalibrator by DirectMethod with 52120AAmplifier by DirectMethod
2 A to 20 A 0.5 % to 0.11 %
45
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (50Hz to1kHz)
Using 5720ACalibrator by DirectMethod with 52120AAmplifier by DirectMethod
20 A to 100 A 0.5 % to 0.11 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 10 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
46
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (50Hz)Using 5502ACalibrator withCurrent Coil byDirect Method
100 A to 1000 A 0.703%
47
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
1 mV to 2 mV 0.57 % to 0.276 %
48
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
2 mV to 20 mV 0.276 % to 0.03 %
49
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
20 mV to 200 mV 0.03 % to 0.018 %
50
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
20 V to 200 V 0.007 % to 0.008 %
51
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
200 mV to 20 V 0.018 % to 0.007 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 11 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
52
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to100kHz)
Using 5720ACalibrator by DirectMethod
10 V to 100 V 0.005 % to 0.02 %
53
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to10kHz)
Using 5502ACalibrator by DirectMethod
200 V to 1000 V 0.06 % to 0.14 %
54
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
1 mV to 2 mV 0.57 % to 2.3 %
55
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
2 mV to 20 mV 0.26 % to 1.3 %
56
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
20 mV to 200 mV 0.03 % to 1.3 %
57
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
200 mV to 10 V 0.007 % to 0.37 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 12 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
58
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to20kHz)
Using 5720ACalibrator by DirectMethod
100 V to 200 V 0.01%
59
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (50Hz to1kHz)
Using 5720ACalibrator by DirectMethod
200 V to 1000 V 0.008 % to 0.013 %
60
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
1 µF to 90 µF 0.88 % to 1.18 %
61
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
1 nF to 9 nF 1.9 % to 1.2 %
62
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
10 nF to 900 nF 1.2 % to 1.8 %
63
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using CapacitanceDecade box byDirect Method
100 pF to 900 pF 7 % to 1.86 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 13 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
64
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
90 µF to 110 mF 0.5 % to 1.5 %
65
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Inductance (1kHz)Using DecadeInductance Box byDirect Method
1 mH to 10 H 3.50%
66
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ODD Harmonicsdistortion (Current)Upto 41st
Using FlukeMultiproductCalibrator 5502A byDirect Method
100 mA to 6 A 0.75%
67
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ODD Harmonicsdistortion (Voltage)Upto 41st order
Using FlukeMultiproductCalibrator 5502A byDirect Method
100 mV to 60 V 0.75%
68
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Oscilloscope -Horizontal Deflection(Time Base)
Using 5502ACalibrator by DirectMethod
2 nS to 2 S 0.1 % to 0.3 %
69
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Oscilloscope -Vertical Deflection(Square Wave@1kHz Freq. & DCFunction)
Using 5502ACalibrator by DirectMethod
10 mV to 120 V 0.5%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 14 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
70
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.1PF) (120V to240V@ 0.1 to 20A)
Using 5502ACalibrator by DirectMethod
1.2 W to 480 W 5.0%
71
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.2PF) (120V [email protected] to 20A)
Using 5502ACalibrator by DirectMethod
2.4 W to 960 W 2.93%
72
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.5PF) (120V to240V & 0.1 to 20A)
Using 5502ACalibrator by DirectMethod
12 W to 1200 W 1.17 % to 1.2 %
73
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.8PF) (120V to240V @ 0.1 to 20A)
Using 5502ACalibrator by DirectMethod
9.6 W to 3840 W 2.93%
74
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat UPF) (120V to240V @ 0.01A to20A)
Using 5502ACalibrator by DirectMethod
1.1 W to 4800 W 2.92 % to 0.75 %
75
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power FactorUsing 5502ACalibrator by DirectMethod
0.25 PF to 1 PF 0.04PF
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 15 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
76
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using DecadeResistance Box
0.001 ohm to 0.01ohm 2.6%
77
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using DecadeResistance Box 0.01 ohm to 0.1 ohm 1.15%
78
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using DecadeResistance Box 0.1 ohm to 1 ohm 1.15 % to 0.8 %
79
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using Std Resistorby Direct Method 1 G ohm 0.034%
80
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using Decade MegaOhm Box 1 G ohm to 1 T ohm 1.2 % to 4.71 %
81
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1 kilo ohm 0.0012%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 16 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
82
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1 mega ohm 0.003%
83
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing FixedResistnace by DirectMethod
1 mili ohm 0.04%
84
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1 ohm 0.012%
85
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
1 ohm to 30 ohm 1.17 % to 0.07 %
86
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1.9 kilo ohm 0.0013%
87
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1.9 mega ohm 0.003%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 17 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
88
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1.9 ohm 0.011%
89
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
10 kilo ohm 0.0012%
90
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
10 mega ohm 0.005%
91
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing FixedResistnace by DirectMethod
10 mili ohm 0.03%
92
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
10 ohm 0.003%
93
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
100 kilo ohm 0.0012%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 18 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
94
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
100 mega ohm 0.013%
95
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing FixedResistnace by DirectMethod
100 mili ohm 0.02%
96
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
100 ohm 0.0012%
97
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
19 kilo ohm 0.0012%
98
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
19 mega ohm 0.006%
99
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
19 ohm 0.003%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 19 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
100
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
190 kilo ohm 0.0013%
101
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
190 ohm 0.0012%
102
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
290 M ohm to 1 Gohm 0.5 % to 1.79 %
103
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
3 M ohm to 30 Mohm 0.07 % to 0.1 %
104
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
30 M ohm to 290 Mohm 0.1 % to 0.5 %
105
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
30 ohm to 300 ohm 0.072 % to 0.019 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 20 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
106
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using Decade MegaOhm Box
300 M ohm to 1 Gohm 1.17%
107
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
300 ohm to 300 kohm 0.019 % to 0.013 %
108
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Source,Measure)
ResistanceUsing 5502ACalibrator by DirectMethod
300 k ohm to 3 Mohm 0.013 % to 0.07 %
109
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing Picoammeter6485 by DirectMethod
0.02 µA to 1 µA 0.55%
110
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 1 µA to 10 µA 0.06 % to 0.006 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 21 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
111
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 1 A to 20 A 0.021 % to 0.065 %
112
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing Picoammeter6485 by DirectMethod
1 nA to 20 nA 0.94%
113
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 10 µA to 10 mA 0.006 % to 0.0023 %
114
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 10 mA to 1 A 0.0023 % to 0.021 %
115
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing Power MeterWT3000 by DirectMethod
20 A to 30 A 0.15%
116
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing DC Shunt and8508A DMM byDirect Method
30 A to 100 A 0.9%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 22 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
117
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Power (1V to1000V) (100mA to20A)
Using PowerAnalyser WT3000 byDirect Method
0.1 mW to 20 kW 3.8 % to 0.3 %
118
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC VoltageUsing 5720ACalibrator with8508A byComparison Method
0.1 mV to 1 mV 0.366 % to 0.043 %
119
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage Using 8508A DMMby Direct Method 0.1 mV to 10 mV 0.13 % to 0.013 %
120
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC VoltageUsing 5720ACalibrator with8508A byComparison Method
1 mV to 10 mV 0.043 % to 0.004 %
121
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC VoltageUsing 5720ACalibrator with8508A byComparison Method
10 mV to 100 mV 0.004 % to 0.0014 %
122
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage Using 8508A DMMby Direct Method 10 mV to 100 mV 0.013 % to 0.0008 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 23 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
123
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage Using 8508A DMMby Direct Method 100 mV to 1000 V 0.0008%
124
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage (HighVoltage)
Using HV Divider byDirect Method: 1kV to 20kV 1.6% to 2.1%
125
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
1 µA to 10 µA 0.82 % to 0.09 %
126
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
10 µA to 200 µA 0.09 % to 0.008 %
127
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5502ACalibrator withCurrent Coil byDirect Method
100 A to 1000 A 0.802%
128
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator with52120A Amplifier byDirect Method
2 A to 20 A 0.023 % to 0.05 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 24 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
129
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator with52120A Amplifier byDirect Method
20 A to 100 A 0.05 % to 0.08 %
130
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
20 mA to 200 mA 0.0044 % to 0.006 %
131
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
200 µA to 20 mA 0.008 % to 0.0044 %
132
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
200 mA to 2 A 0.006 % to 0.01 %
133
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC Power @1V to1000V, 1A to 20A
Using MuliproductCalibrator 5502Awith Power Option
1 W to 20 kW 2.93 % to 0.2 %
134
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
100 mV to 100 V 0.0014 % to 0.0007%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 25 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
135
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
100 V to 1000 V 0.0007 % to 0.0009%
136
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (B-Type)
Using 8505A DMMby Direct Method 200 °C to 1820 °C 0.061°C
137
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (C-Type)
Using 8505A DMMby Direct Method 200 °C to 2320 °C 0.022°C
138
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (E-Type)
Using 8505A DMMby Direct Method -200 °C to 1000 °C 0.012°C
139
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (J-Type)
Using 8505A DMMby Direct Method -210 °C to 1200 °C 0.012°C
140
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (K-Type)
Using 8505A DMMby Direct Method -210 °C to 1372 °C 0.012°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 26 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
141
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (L-Type)
Using 8505A DMMby Direct Method -200 °C to 900 °C 0.018°C
142
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (N-Type)
Using 8505A DMMby Direct Method -200 °C to 1300 °C 0.014°C
143
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (R-Type)
Using 8505A DMMby Direct Method -50 °C to 1768 °C 0.054°C
144
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (RTD)
Using 8505A DMMby Direct Method -200 °C to 850 °C 0.01°C
145
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (S-Type)
Using 8505A DMMby Direct Method -50 °C to 1768 °C 0.031°C
146
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (T-Type)
Using 8505A DMMby Direct Method -200 °C to 400 °C 0.01°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 27 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
147
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (U-Type)
Using 8505A DMMby Direct Method -200 °C to 600 °C 0.012°C
148
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (B-Type)
Using 5720ACalibrator by DirectMethod
200 °C to 1820 °C 0.232°C
149
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (C-Type)
Using 5720ACalibrator by DirectMethod
200 °C to 2320 °C 0.037°C
150
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (E-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 1000 °C 0.28°C
151
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (J-Type)
Using 5720ACalibrator by DirectMethod
-210 °C to 1200 °C 0.029°C
152
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (K-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 1372 °C 0.036°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 28 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
153
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (L-Type)
Using 5720ACalibrator by DirectMethod
-200 °C to 900 °C 0.016°C
154
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (N-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 1300 °C 0.047°C
155
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (R-Type)
Using 5720ACalibrator by DirectMethod
-50 °C to 1768 °C 0.155°C
156
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (RTD)
Using 5502ACalibrator by DirectMethod
-200 °C to 800 °C 0.25°C
157
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (S-Type)
Using 5720ACalibrator by DirectMethod
-50 °C to 1768 °C 0.12°C
158
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (T-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 400 °C 0.031°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 29 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
159
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (U-Type)
Using 5720ACalibrator by DirectMethod
-200 °C to 600 °C 0.026°C
160
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
1 hr to 5 hr 0.14 s to 6 s
161
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
1 s to 60 s 0.0252 s to 0.036 s
162
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
5 hr to 24 hr 6 s to 21 s
163
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
60 s to 1 hr 0.03 s to 0.14 s
164
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
200 ms to 1 s 0.0252s
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 30 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
165
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
FrequencyUsing Timer/CounterCNT91 by DirectMethod
1 Hz to 3 GHz 0.002 % to 0.0008 %
166
ELECTRO-TECHNICAL-TIME &FREQUENCY(Source)
FrequencyUsing 5502ACalibrator by DirectMethod
1 Hz to 2 MHz 0.004%
167
ELECTRO-TECHNICAL-TIME &FREQUENCY(Source)
FrequencyUsing 5502ACalibrator by DirectMethod
2 MHz to 600 MHz 0.003%
168FLUID FLOW-FLOWMEASURINGDEVICES
Flow Rate (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
1 slm to 2 slm 0.41% Rdg.
169FLUID FLOW-FLOWMEASURINGDEVICES
Flow Rate (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
100 sccm to 1 slm 0.41% Rdg.
170FLUID FLOW-FLOWMEASURINGDEVICES
Flow Rate (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
2 slm to 50 slm 0.40% Rdg.
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 31 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
171FLUID FLOW-FLOWMEASURINGDEVICES
Flow Rate (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
50 sccm to 100sccm 0.40% Rdg.
172FLUID FLOW-FLOWMEASURINGDEVICES
Flow Rate (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
50 slm to 100 slm 0.48% Rdg.
173FLUID FLOW-FLOWMEASURINGDEVICES
Fluid Flow (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
1 sccm to 10 sccm 2.5%
174FLUID FLOW-FLOWMEASURINGDEVICES
Fluid Flow (AIR/N2)
Using Fluke Molbloc,Laminar elementand Mass FlowTerminal byComparison Method.
10 sccm to 50 sccm 0.4%
175FLUID FLOW-FLOWMEASURINGDEVICES
Fluid Flow (Air/N2)Using Alicat MassFlow Controller bycomparison method
100 slm to 500 slm 4slm
176MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
10 RPM to 100 RPM 0.63RPM
177MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
100 RPM to 1000RPM 1.52RPM
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 32 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
178MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
1000 RPM to 5000RPM 1.97RPM
179MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
10000 RPM to 60000RPM 3.71RPM
180MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
5000 RPM to 10000RPM 2.85RPM
181MECHANICAL-ACCELERATIONAND SPEED
RPM (Contact)Using DigitalTachometer byComparison Method
10 RPM to 100 RPM 1.9RPM
182MECHANICAL-ACCELERATIONAND SPEED
RPM (Contact)Using DigitalTachometer byComparison Method
100 RPM to 1000RPM 2.3RPM
183MECHANICAL-ACCELERATIONAND SPEED
RPM (Contact)Using DigitalTachometer byComparison Method
1000 RPM to 3000RPM 2.9RPM
184MECHANICAL-ACCELERATIONAND SPEED
RPM (Non-Contact)Using DigitalTachometer byComparison Method
10 RPM to 100 RPM 0.63RPM
185MECHANICAL-ACCELERATIONAND SPEED
RPM (Non-Contact)Using DigitalTachometer byComparison Method
100 RPM to 1000RPM 1.52RPM
186MECHANICAL-ACCELERATIONAND SPEED
RPM (Non-Contact)Using DigitalTachometer byComparison Method
1000 RPM to 5000RPM 1.97RPM
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 33 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
187MECHANICAL-ACCELERATIONAND SPEED
RPM (Non-Contact)Using DigitalTachometer byComparison Method
10000 RPM to 60000RPM 3.71RPM
188MECHANICAL-ACCELERATIONAND SPEED
RPM (Non-Contact)Using DigitalTachometer byComparison Method
5000 RPM to 10000RPM 2.85RPM
189MECHANICAL-ACCELERATIONAND SPEED
RPM (Non-Contact)Using DigitalTachometer byComparison Method
60000 RPM to 90000RPM 4.26RPM
190MECHANICAL-ACCELERATIONAND SPEED
Vibration Meter /Accelerometer withTransducer
Using VibrationCalibrator byComparison Method
Acceleration: Up to95m/s2 (50Hz to5000Hz)
5.5%
191MECHANICAL-ACCELERATIONAND SPEED
Vibration Meter /Accelerometer withTransducer
Using VibrationCalibrator byComparison Method
Displacement: Up to1250µm (50Hz to1000Hz)
4.4%
192MECHANICAL-ACCELERATIONAND SPEED
Vibration Meter /Accelerometer withTransducer
Using VibrationCalibrator byComparison Method
Velocity: Up to239mm/s (50Hz to5000Hz)
4.1%
193 MECHANICAL-ACOUSTICS
Acoustic Pressure(Sound)
Using SoundCalibrator 94 dB &114 dB 1.1dB
194MECHANICAL-DENSITY ANDVISCOSITY
Density Hydrometer/ Specific GravityHydrometer
Using ReferenceDensity Hydrometerby ComparisonMethod as per IS3104 (Part I&II):1982
0.6 g/ml to 1.6 g/ml 0.0012g/ml
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 34 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
195MECHANICAL-DENSITY ANDVISCOSITY
Hydrometer -Density,Hydrometer,TwaddleHydrometer, BaumeHydrometer, SpecificGravity Hydrometer,Brix Hydrometer,Lactometer,Alcometer.
Using WeighingBalance withresolution 0.01 mgby Hydrostaticweighing method asper NISP SP 250-78Standard.
0.6 g/ml to 2.000g/ml 0.0003g/ml
196
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
'V' Block Parameter (Flatness /Parallelism /Squareness /Symmetry )
Using ElectronicComparator withProbe & CylindricalMandrel byComparison Method
Length: Up to 300mm 5.4µm
197
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Angle Plate(Flatness,Parallelism,Squareness)
Using Digital HeightGauge byComparison Method
Length: Up to 300mm 8.3µm
198
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Bevel / DegreeProtractor /inclinometer/Clinometer(L.C.=1sec)
Using Angle Gaugeby ComparisonMethod
Up to 360 ° 4.0sec
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 35 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
199
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Caliper CheckerUsing Slip Gauge Set& Digital HeightGauge byComparison Method
0 to 660 mm 3.7µm
200
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
centrimeter L.C 0.01mm and CentreDistance Gauge
Using Slip Gauge SetGrade '0' & SlipGauge Accessories,Caliper Checker &2D Height Gauge byComparison Method
Up to 600 mm 10.0µm
201
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Coating ThicknessGauge(L.C.=0.001mm)
Using Master Foilsby ComparisonMethod
Up to 6000 µm 3.0µm
202
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Combination Set(L.C.=1°)
Using Angle Gaugeby ComparisonMethod
0 to 180 ° 43.7min
203
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Comparator Stand (Parameter Flatness )
ElectronicComparator withProbe & Slip GaugeSet by ComparisonMethod
300 X 300mm / Dia.300 mm 3.4µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 36 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
204
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cube Mould (parameter -Length /Angle )
Using , DigitalVernier, BevelProtractor byComparison Method
Length:0 to300mm,Angle: to 90°
Length:16.8µm,Angle: 3.6min
205
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cylindrical SettingMaster / O.D. Gauge/ Test Mandrel
Using Slip Gauge SetGrade '0', ElectronicComparator withProbe byComparison Method
200 mm to 500 mm 6.9µm
206
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Cylindrical settingmaster/O.D.Gauge/Test Mandrel
Using Slip Gauge SetGrade '0', ElectronicComparator withProbe byComparison Method
3 mm to 200 mm 2.0µm
207
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Depth Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0' byComparison Method
Up to 300 mm 3.5µm
208
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier Caliper(L.C.=0.01mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
300 mm to 600 mm 10.4µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 37 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
209
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier Caliper(L.C.=0.01mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
600 mm to 1000mm 12.3µm
210
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier Caliper(L.C.=0.01mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
Up to 300 mm 9.1µm
211
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier DepthGauge(L.C.=0.01mm)
Using Slip Gauge SetGrade '0' byComparison Method
Up to 300 mm 8.0µm
212
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier HeightGauge(L.C.=0.0001mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
300 mm to 600 mm 7.3µm
213
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier HeightGauge(L.C.=0.0001mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
600 mm to 1000mm 8.3µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 38 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
214
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier HeightGauge(L.C.=0.0001mm)
Using Slip Gauge SetGrade '0' CircularSteel Length BarCaliper Checker byComparison Method
Up to 300 mm 3.4µm
215
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Bore Gauge /Bore Gauge (ForTransmission)
Using Electronic DialCalibration Tester &ElectronicComparator withProbe byComparison Method
Up to 2 mm 1.4µm
216
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Bore Gauge /Bore Gauge(Split/Circular Type)For Transmission
Using Slip Gauge SetGrade '0', SlipGauge AccessoriesSet & ElectronicComparator withProbe byComparison Method
Up to 2 mm 3.0µm
217
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial CalibrationTester(L.C.=0.0001mm)
Using ElectronicComparator withProbe byComparison Method
Up to 25 mm 1.3µm
218
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Comparator /Mikrokator(L.C.=0.0005mm)
Using Electronic DialCalibration Tester &ElectronicComparator withProbe byComparison Method
-0.05 mm to 0.05mm 1.2µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 39 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
219
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Indicator (Lever)(L.C.=0.001mm)
Using Electronic DialCalibration Tester &ElectronicComparator withProbe byComparison Method
Up to 2 mm 1.3µm
220
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Indicator(Plunger)(L.C.=0.001mm)
Using Electronic DialCalibration Tester,ElectronicComparator withProbe & Slip GaugeSet by ComparisonMethod
25 mm to 100 mm 2.6µm
221
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial Indicator(Plunger)(L.C.=0.001mm)
Using DialCalibration Tester,ElectronicComparator withProbe & Slip GaugeSet by ComparisonMethod
Up to 25 mm 2.3µm
222
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial ThicknessGauge(L.C.=0.001mm)
Using Slip Gauge SetGrade '0' byComparison Method
Up to 100 mm 1.3µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 40 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
223
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Diamond ConeIndentor (parameterLength / angle )Vickers / Knoop /Rockwel
Using ProfileProjector byComparison Method
Length:0 to100mm,Angle:0 to360°
Length: 16.8µm,Angle: 3.6°
224
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Electronic Blue Level/ Spirit Level(L.C.=0.001mm/m)
Using Slip GaugeSet, Sine Bar &Electronic Blue Levelby ComparisonMethod
Length: Up to 400mm 3.21µm/m
225
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
ElectronicComparator /Indicator with Probe/ LVDT (L.C.=0.1µm)
Using Slip Gauge SetGrade 'K' byComparison Method
Up to 100 mm 0.6µm
226
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Engineer's Parallel /Rectangular Block
Using ElectronicComparator withProbe byComparison Method
Length: Up to 300mm 4.0µm
227
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Engineer's Square (ParameterSquareness )
Using Digital 2DHeight Gauge byComparison Method
Up to 600 mm 8.0µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 41 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
228
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0', CircularSteel Length BarOptical Flat &Parallels byComparison Method
100 mm to 200 mm 2.6µm
229
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0', CircularSteel Length BarOptical Flat &Parallels byComparison Method
200 mm to 400 mm 4.5µm
230
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0', CircularSteel Length BarOptical Flat &Parallels byComparison Method
400 mm to 600 mm 6.5µm
231
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0', CircularSteel Length BarOptical Flat &Parallels byComparison Method
600 mm to 800 mm 8.9µm
232
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0', CircularSteel Length BarOptical Flat &Parallels byComparison Method
800 mm to 1000mm 11.0µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 42 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
233
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
External Micrometer(L.C.=0.001mm)
Using Slip Gauge SetGrade '0', CircularSteel Length BarOptical Flat &Parallels byComparison Method
Up to 100 mm 1.8µm
234
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Feeler GaugeUsing DigimaticMicrometer byComparison Method
0.01 mm to 2 mm 1.8µm
235
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Flakiness Gauge /Elongation Gauge (parameter -length,width, thickness )
Using ProfileProjector & DigitalVernier byComparison Method
0 mm to 100 mm 16.8µm
236
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Flakiness SievesUsing ProfileProjector byComparison Method:
0.032 mm to 25 mm 10µm
237
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
FoilsUsing ElectronicComparator withProbe byComparison Method
0.005 mm to 12 mm 1.3µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 43 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
238
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Glass Scale(L.C.=0.1mm)
Using ProfileProjector byComparison Method
Up to 200 mm 9.0µm
239
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Groove Micrometer(L.C.=0.01mm)
Using Slip Gauge SetGrade '0' byComparison Method
Up to 100 mm 6.6µm
240
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Hegman GaugeUsing ElectronicComparator withProbe byComparison Method
Up to 100 µm 2.4µm
241
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Dial Caliper(L.C.=0.001mm)
Using Slip Gauge Set& Slip GaugeAccessories byComparison Method
5 mm to 100 mm 5.8µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 44 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
242
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Micrometer(Extension Rod)
Using Slip Gauge SetGrade '0', SlipGauge AccessoriesCircular Steel,Length Bar,ElectronicComparator withProbe byComparison Method
13 mm to 500 mm 6.4µm
243
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside Micrometer(Extension Rod)
Using Slip Gauge SetGrade '0', SlipGauge AccessoriesCircular Steel,Length Bar,ElectronicComparator withProbe byComparison Method
500 mm to 1000mm 11.0µm
244
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Inside MicrometerRange (Two Points)(L.C.=0.01mm)
Using Slip Gauge SetGrade '0', SlipGauge AccessoriesCircular Steel,Length Bar,ElectronicComparator withProbe byComparison Method
25 mm to 1050 mm 6.7µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 45 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
245
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
L Square / GraniteSquare
Using Digital HeightGauge byComparison Method
Length: Up to 500mm 8.0µm
246
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Lever Arm / MasterConnecting Rod /PCD / RecieverGauge
Using Slip GaugeSet, 2D HeightGauge, ProfileProjector, LMM, Dig.Vernier, DigimaticMicrometer,ElectronicComparator, Dig.Protractor
Length:0 to600mm,Angle:0 to360°
Length: 16.8µm,Angle: 3.6min
247
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Master Rod / LengthBar
Using Slip Gauge SetGrade '0', CircularSteel, Length Bar,ElectronicComparator withProbe byComparison Method
200 mm to 400 mm 4.6µm
248
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Master Rod / LengthBar
Using Slip Gauge SetGrade '0', CircularSteel, Length Bar,ElectronicComparator withProbe byComparison Method
25 mm to 200 mm 2.8µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 46 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
249
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Master Rod / LengthBar
Using Slip Gauge SetGrade '0', CircularSteel, Length Bar,ElectronicComparator withProbe byComparison Method
400 mm to 600 mm 7.1µm
250
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Master Rod / LengthBar
Using Slip Gauge SetGrade '0', LengthBar, ElectronicComparator withProbe byComparison Method
600 mm to 1000mm 12.3µm
251
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Micrometer Head(L.C.=0.001mm)
Using ElectronicComparator &Optical Flat byComparison Method
Up to 50 mm 3.0µm
252
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Outside Dial Caliper/ Pistol Caliper(L.C.=0.001mm)
Using Slip Gauge Set& Slip GaugeAccessories byComparison Method
0 to 100 mm 5.8µm
253
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Pin Gauge / ThreadMeasuring Wire
Using Slip Gauge SetGrade '0', ElectronicComparator withProbe byComparison Method
0.29 mm to 25 mm 1.4µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 47 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
254
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauge /Height MasterGauge / WidthGauge
Using Slip Gauge SetGrade '0', ElectronicComparator withProbe byComparison Method
1 mm to 100 mm 2.0µm
255
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauge /Height MasterGauge / WidthGauge
Using Slip Gauge SetGrade '0', ElectronicComparator withProbe byComparison Method
100 mm to 200 mm 2.5µm
256
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Plug Gauge /Height MasterGauge / WidthGauge
Using Slip Gauge SetGrade '0', ElectronicComparator withProbe byComparison Method
200 mm to 300 mm 5.0µm
257
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Plain Ring GaugeLength MeasuringMachine byComparison Method
3 mm to 100 mm 1.2µm
258
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Protractor / SetSquare (L.C.=1°)
Using ProfileProjector byComparison Method
Up to 360 ° 3.4min
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 48 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
259
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Radius Gauge /Radius Template
Using ProfileProjector byComparison Method
Up to 40 mm 11.7µm
260
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
ScaleUsing Scale & TapeCalibrator byComparison Method
Up to 2000 mm 231*[sqrt(L/1000)]µm
261
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Sine Bar / SineCenter / Sine Table(Parallelism ,Angle,Parrallelism ofcenter axis tobottom contactplane)
Using Slip Gauge SetGrade '0' DialIndicator (L)ElectronicComparator withProbe and AngleGauge byComparison Method
Angle: 0 to 90 ° 7.7sec
262
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge / GapGauge
Using Slip Gauge SetGrade '0' byComparison Method
1 mm to 100 mm 2.5µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 49 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
263
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge / GapGauge
Using Slip Gauge SetGrade '0' byComparison Method
100 mm to 200 mm 3.2µm
264
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge / GapGauge
Using Slip Gauge SetGrade '0' byComparison Method
200 mm to 300 mm 4.0µm
265
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Snap Gauge / GapGauge
Using Slip Gauge SetGrade '0' byComparison Method
300 mm to 400 mm 8.3µm
266
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge(Straightness)
Using Slip Gauge SetGrade '0' & SurfacePlate by ComparisonMethod
600 mm to 1200mm 17.7µm
267
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge(Straightness)
Using Slip Gauge SetGrade '0' & SurfacePlate by ComparisonMethod
Up to 600 mm 12.1µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 50 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
268
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface PlateUsing ElectronicLevel by ComparisonMethod
1000 mm to 1000mm
1.4*[sqrt(L+W)/125]µm
269
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Tape & ScaleCalibrator (L.C.=0.005mm)
Using Slip Gauge Setby ComparisonMethod
Up to 1000 mm 10.5µm
270
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Tape / Pie Tape(Metallic, Woven,Fiber)
Using Scale & TapeCalibrator byComparison Method
Up to 100 m 232*[sqrt(L/1000)]µm
271
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Taper Scale(L.C.=0.1mm)
Using ProfileProjector byComparison Method
0.4 mm to 100 mm 10.0µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 51 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
272
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Template / PlainWork Piece /Inspection Jigs &Fixture
Using Slip GaugeSet, 2D HeightGauge, ProfileProjector, LMM, Dig.Vernier, DigimaticMicrometer,ElectronicComparator, Dig.Protractor byComparison Method
Length:0 to600mm,Angle:0 to360°
Length: 16.8µm,Angle: 3.6min
273
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Test SievesUsing ProfileProjector byComparison Method
0.032 mm to 25 mm 10µm
274
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Pitch GaugeUsing ProfileProjector byComparison Method
Flank Angle: Up to90 ° 6'20"
275
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Pitch GaugeUsing ProfileProjector byComparison Method
Up to 6 mm 9.0µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 52 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
276
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Plug Gauge(Parallel, EffectiveDiameter, MajorDiameter)
Using FloatingCarriage DiameterMeasuring Machine,Thread MeasuringWire, CylindricalMaster byComparison Method
3 mm to 100 mm 4.0µm
277
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Plug Gauge(Parallel, EffectiveDiameter,MajorDiameter)
Using FloatingCarriage DiameterMeasuring Machine,Thread MeasuringWire, CylindricalMaster byComparison Method
100 mm to 160 mm 4.0µm
278
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Plug Gauge(Taper)-EffectiveDiameter,MajorDiameter
Using FloatingCarriage DiameterMeasuring Machine,Thread MeasuringWire, CylindricalMaster byComparison Method
Up to 100 mm 3.6µm
279
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Thread Ring Gauge(Effective Diameter)
Using LengthMeasuring Machinewith Master SettingRing by ComparisonMethod
4 mm to 100 mm 1.5µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 53 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
280
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Ultrasonic ThicknessGauge(L.C.=0.1mm)
Using Steel SlipGauge Set Grade 'K'by ComparisonMethod
Up to 100 mm 71µm
281
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
V Anvil Micrometer(L.C.=0.001mm)
Using CylindricalSetting Master byComparison Method
Up to 100 mm 8.8µm
282
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Vernier Caliper ( Dial/ Digital )L.C.=0.02mm
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
1000 mm to 2000mm 15.5µm
283
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld / Hi-Low Gauge/ Bridge Cam Gauge
Using ProfileProjector byComparison Method
Length: 0 to 60mm,Angle: 0 to 60°
Length: 16.8µm,Angle: 6'20"
284
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld Fillet GaugeUsing ProfileProjector byComparison Method
Up to 50 mm 49µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 54 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
285
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld Gauge (Angle)
Using Slip Gauge SetGrade '0', Tape &Scale Calibrator,Profile Projector byComparison Method
Up to 60 ° 6'20"
286
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Weld Gauge (Scale /Depth)
Using Slip Gauge SetGrade '0', Tape &Scale Calibrator,Profile Projector byComparison Method
Up to 50 mm 57.7µm
287
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Wire GaugeUsing ProfileProjector byComparison Method
0.025 mm to 10 mm 8.0µm
288MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Length MeasuringMachine (L.C.=0.0001mm)
Using Slip Gauge SetGrade 'K' byComparison Method
Up to 100 mm 0.51µm
289MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector(Angular L.C.=1sec)
Using AngularGraticule / AngleGauge Set byComparison Method
0 to 360 ° 2.35min
290MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector(LinearL.C.=0.001mm)
Using Glass Scale /Gauge Block byComparison Method
Up to 200 mm 5.62µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 55 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
291MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector(Magnification)
Using Glass Scale &Digimatic Caliper byComparison Method
10X, 20X, 50X, 100X 0.28%
292MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Carbide)
Using Slip Gauge SetGrade 'K' & Grade '0'Slip GaugeCalibrator byComparison Method
0.5 mm to 25 mm 0.11µm
293MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Carbide)
Using Slip Gauge SetGrade 'K' & Grade '0'Slip GaugeCalibrator byComparison Method
25 mm to 50 mm 0.14µm
294MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Carbide)
Using Slip Gauge SetGrade 'K' & Grade '0'Slip GaugeCalibrator byComparison Method
50 mm to 75 mm 0.17µm
295MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Carbide)
Using Slip Gauge SetGrade 'K' & Grade '0'Slip GaugeCalibrator byComparison Method
75 mm to 100 mm 0.21µm
296MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Steel)Using Slip Gauge SetGrade 'K' & SlipGauge Calibrator byComparison Method
0.5 mm to 25 mm 0.15µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 56 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
297MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Steel)Using Slip Gauge SetGrade 'K' & SlipGauge Calibrator byComparison Method
25 mm to 50 mm 0.22µm
298MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Steel)Using Slip Gauge SetGrade 'K' & SlipGauge Calibrator byComparison Method
50 mm to 75 mm 0.27µm
299MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip Gauge (Steel)Using Slip Gauge SetGrade 'K' & SlipGauge Calibrator byComparison Method
75 mm to 100 mm 0.39µm
300MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip GaugeAccessories
Using Slip Gauge SetGrade '0' DialIndicator (L) byComparison Method
Up to 300 mm 2.0µm
301MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip GaugeCalibrator(L.C.=0.01µm)
Using Bridge SlipGauge Set K-Gradeby ComparisonMethod
0 to 100 mm 0.15µm
302MECHANICAL-HARDNESSTESTINGMACHINES
Rubber HardnessTester-IndentationDepth Calibration(Type A, D, AO, AM)
Using DialCalibration Tester &Holding Fixture asper ASTM D2240/ISO 18898
0 to 100 Shore 0.6Shore
303MECHANICAL-MOBILE FORCEMEASURINGSYSTEM
Push Pull GaugeUsing Newtonweights & FrameFixture as perVDI/VDE 2624-2.1
100 N to 500 N 1.29N
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 57 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
304MECHANICAL-MOBILE FORCEMEASURINGSYSTEM
Push Pull GaugeUsing Newtonweights & FrameFixture as perVDI/VDE 2624-2.1
5 N to 100 N 0.58N
305
MECHANICAL-PRESSUREBALANCE ORDEAD WEIGHTTESTER
dead weight testerusing 7300 crossfloat method as pereuromet
70 bar to 1750 bar 0.007% of Rdg
306
MECHANICAL-PRESSUREBALANCE ORDEAD WEIGHTTESTER
Hydraulic DeadWeight Tester
Using Piston GaugePC-7300 by CrossFloat Method(Euramet cg-3)
3.5 bar (g) to 70 bar(g) 0.008% Rdg.
307
MECHANICAL-PRESSUREBALANCE ORDEAD WEIGHTTESTER
Hydraulic DeadWeight Tester
Using Piston GaugePC-7300 by CrossFloat Method(Euramet cg-3)
70 bar (g) to 1750bar (g) 0.007% Rdg.
308
MECHANICAL-PRESSUREBALANCE ORDEAD WEIGHTTESTER
Pneumatic DeadWeight Tester
Using Piston GaugePC-7100/7600 byCross Float Method(Euramet cg-3)
0.1 bar (g) to 3.5 bar(g) 0.007% Rdg.
309
MECHANICAL-PRESSUREBALANCE ORDEAD WEIGHTTESTER
Pneumatic DeadWeight Tester
Using Piston GaugePC-7100/7600 byCross Float Method(Euramet cg-3)
5 bar (g) to 70 bar(g) 0.008% Rdg.
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 58 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
310MECHANICAL-PRESSUREINDICATINGDEVICES
Absolute PressureIndicating Devices,Pressure Transmitter
Using Piston GaugePC-7100/7600 byComparison Method(DKD-R-6-1)
0.08 bar (abs) to 3.5bar (abs) 0.015% Rdg.
311MECHANICAL-PRESSUREINDICATINGDEVICES
Absolute PressureIndicating Devices,Pressure Transmitter
Using Piston GaugePC-7100/7600 byComparison Method(DKD-R-6-1)
3.5 bar (abs) to 70bar (abs) 0.008% Rdg.
312MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,PressureTransmitter,Pressure Switches.
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
100 bar (g) to 1000bar (g) 0.57bar
313MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,PressureTransmitter,Pressure Switches.
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
20 bar (g) to 160 bar(g) 0.07bar
314MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,PressureTransmitter,Pressure Switches.
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
40 bar (g) to 400 bar(g) 0.37bar
315MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,Pressure Transmitter
Using Piston GaugePC-7300 byComparison Method(DKD-R-6-1)
2 bar (g) to 70 bar(g) 0.011% Rdg.
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 59 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
316MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,Pressure Transmitter
Using Piston GaugePC-7300 byComparison Method(DKD-R-6-1)
70 bar (g) to 1750.0bar (g) 0.0092% Rdg.
317MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using MultifunctionCalibrator withExternal Sensor
0 to 10 mbar (g) 0.021mbar
318MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using Low PressureCalibrator
0 mbar (g) to 200mbar (g) 0.17mbar
319MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
0.2 bar (g) to 2 bar(g) 0.003bar
320MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
2 bar (g) to 20 bar(g) 0.02bar
321MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,Pressure Transmitter
Using Low PressureController byComparison Method(DKD-R-6-1)
0 to 150 mbar (g) 0.015mbar
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 60 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
322MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,Pressure Transmitter
Using Piston GaugePC-7100/7600 byComparison Method(DKD-R-6-1)
0.15 bar (g) to 3.5bar (g) 0.0081% Rdg.
323MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,Pressure Transmitter
Using Piston GaugePC-7100/7600 byComparison Method(DKD-R-6-1)
3.5 bar (g) to 70 bar(g) 0.008% Rdg.
324MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using MultifunctionCalibrator withExternal Sensor
0 to -10 mbar 0.021mbar
325MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using Low PressureCalibrator, DigitalVacuum Gauge byComparison Method(DKD-R-6-1)
0 to -200 mbar (g) 0.176mbar
326MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using Low PressureCalibrator, DigitalVacuum Gauge byComparison Method(DKD-R-6-1)
-0.2 bar (g) to -0.95bar (g) 1.0mbar
327MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using MultifunctionCalibrator withExternal Sensor
-0.2 bar to -0.95 bar 1.0mbar
328MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using MultifunctionCalibrator withExternal Sensor
-10 mbar to -200mbar 0.2mbar
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 61 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
329MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, VacuumTransmitter
Using Low PressureController byComparison Method(DKD-R-6-1)
0 mbar (g) to -150mbar (g) 0.022 mbar
330MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, VacuumTransmitter
Using DWT-P3025-Iby ComparisonMethod (DKD-R-6-1)
-0.15 bar (g) to -0.95bar (g) 0.021% Rdg.
331MECHANICAL-TORQUEGENERATINGDEVICES
Torque WrenchUsing ElectronicTorque WrenchTester as per ISO6789:2003 & 2017
10 Nm to 100 Nm 1.5% of Rdg.
332MECHANICAL-TORQUEGENERATINGDEVICES
Torque WrenchUsing ElectronicWrench Tester asper ISO 6789:2003 &2017
100 Nm to 1000 Nm 1.8% of Rdg.
333 MECHANICAL-VOLUME Burette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
0.1 ml to 25 ml 0.24µl
334 MECHANICAL-VOLUME Burette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
25 ml to 50 ml 0.49µl
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 62 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
335 MECHANICAL-VOLUME Burette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
50 ml to 100 ml 0.94µl
336 MECHANICAL-VOLUME Dispenser
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
10 ml to 100 ml 3.63µl
337 MECHANICAL-VOLUME
Measuring Cylinder /Jar
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
0.1 ml to 10 ml 0.3µl
338 MECHANICAL-VOLUME
Measuring Cylinder /Jar
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
10 ml to 25 ml 0.3µl
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 63 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
339 MECHANICAL-VOLUME
Measuring Cylinder /Jar
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
100 ml to 500 ml 0.017ml
340 MECHANICAL-VOLUME
Measuring Cylinder /Jar
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
1000 ml to 5000 ml 0.29ml
341 MECHANICAL-VOLUME
Measuring Cylinder /Jar
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
25 ml to 100 ml 0.027ml
342 MECHANICAL-VOLUME
Measuring Cylinder /Jar
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
500 ml to 1000 ml 0.266ml
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 64 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
343 MECHANICAL-VOLUME Pipette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
0.1 ml to 5 ml 0.3µl
344 MECHANICAL-VOLUME Pipette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
10 ml to 25 ml 1.1µl
345 MECHANICAL-VOLUME Pipette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
25 ml to 50 ml 1.1µl
346 MECHANICAL-VOLUME Pipette
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
5 ml to 10 ml 0.3µl
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 65 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
347 MECHANICAL-VOLUME
Piston OperatedVolumetricApparatus (Micro-Pipette)
Using ElectronicWeighing Balance(d=0.01/0.1mg) &Distilled Water byGravimetric Methodas per ISO 8655-6
1 ml to 2 ml 0.19µl
348 MECHANICAL-VOLUME
Piston OperatedVolumetricApparatus (Micro-Pipette)
Using ElectronicWeighing Balance(d=0.01/0.1mg) &Distilled Water byGravimetric Methodas per ISO 8655-6
10 µl to 100 µl 0.012µl
349 MECHANICAL-VOLUME
Piston OperatedVolumetricApparatus (Micro-Pipette)
Using ElectronicWeighing Balance(d=0.01/0.1mg) &Distilled Water byGravimetric Methodas per ISO 8655-6
100 µl to 500 µl 0.09µl
350 MECHANICAL-VOLUME
Piston OperatedVolumetricApparatus (Micro-Pipette)
Using ElectronicWeighing Balance(d=0.01/0.1mg) &Distilled Water byGravimetric Methodas per ISO 8655-6
2 ml to 5 ml 0.47µl
351 MECHANICAL-VOLUME
Piston OperatedVolumetricApparatus (Micro-Pipette)
Using ElectronicWeighing Balance(d=0.01/0.1mg) &Distilled Water byGravimetric Methodas per ISO 8655-6
5 ml to 10 ml 0.46µl
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 66 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
352 MECHANICAL-VOLUME
Piston OperatedVolumetricApparatus (Micro-Pipette)
Using ElectronicWeighing Balance(d=0.01/0.1mg) &Distilled Water byGravimetric Methodas per ISO 8655-6
500 µl to 1000 µl 0.11µl
353 MECHANICAL-VOLUME Volumetric Flask
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
1 ml to 25 ml 1.1µl
354 MECHANICAL-VOLUME Volumetric Flask
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
100 ml to 1000 ml 39.6µl
355 MECHANICAL-VOLUME Volumetric Flask
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
1000 ml to 5000 ml 0.38ml
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 67 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
356 MECHANICAL-VOLUME Volumetric Flask
Using ElectronicWeighing Balance(d=0.01/0.1/1/10mg) & Distilled Waterby GravimetricMethod as perISO:4787
25 ml to 100 ml 2.7µl
357MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.01mg)
Using StandardWeight of E1 Class(1mg to 500g), E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
1 mg to 100 g 0.03mg
358MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.1g)
Using StandardWeight of E2 ClassWeights (1mg to10kg), F1 & M1Class Weights (500gto 20kg) byComparison Methodas per OIML R76-1
10 kg to 30 kg 0.24g
359MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.1g)
Using StandardWeight of E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
5 kg to 10 kg 0.09g
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 68 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
360MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.1mg)
Using StandardWeight of E1 Class(1mg to 500g), E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
100 g to 200 g 0.13mg
361MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=1.0mg)
Using StandardWeight of E1 Class(1mg to 500g), E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
200 g to 1000 g 0.91mg
362MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=10mg)
Using StandardWeight of E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
1 kg to 5 kg 8.20mg
363MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1, M1Class & CI Weights(500g to 20kg) byComparison Methodas per OIML R76-1
100 kg to 200 kg 18.70g
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 69 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
364MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1, M1Class & CI Weights(500g to 20kg) byComparison Methodas per OIML R76-1
200 kg to 300 kg 28.25g
365MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1 & M1Class Weights (500gto 20kg) byComparison Methodas per OIML R76-1
30 kg to 50 kg 14.47g
366MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1 & M1Class Weights (500gto 20kg) byComparison Methodas per OIML R76-1
50 kg to 100 kg 14.74g
367 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
1 g 0.009mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 70 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
368 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E2 ClassWeights (500g to10kg) & ElectronicBalance (d=0.001g)by ABBA Method asper OIML R111-1
1 kg 1.63mg
369 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
1 mg 0.01mg
370 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
10 g 0.02mg
371 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
10 mg 0.01mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 71 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
372 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
100 g 0.019mg
373 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
100 mg 0.01mg
374 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
2 g 0.010mg
375 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E2 ClassWeights (500g to10kg) & ElectronicBalance (d=0.01g)by ABBA Method asper OIML R111-1
2 kg 8.58mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 72 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
376 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
2 mg 0.009mg
377 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
20 g 0.038mg
378 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
20 mg 0.009mg
379 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.1mg) by ABBAMethod as per OIMLR111-1
200 g 0.087mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 73 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
380 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
200 mg 0.008mg
381 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
5 g 0.02mg
382 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E2 ClassWeights (500g to10kg) & ElectronicBalance (d=0.01g)by ABBA Method asper OIML R111-1
5 kg 8.81mg
383 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
5 mg 0.01mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 74 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
384 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
50 g 0.02mg
385 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
50 mg 0.01mg
386 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E2 ClassWeights (500g to10kg) & ElectronicBalance (d=0.001g)by ABBA Method asper OIML R111-1
500 g 0.820mg
387 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- F1 Class & Coarser
Using StandardWeights of E1 Class(1mg to 500g) &Electronic Balance(d=0.01mg) byABBA Method as perOIML R111-1
500 mg 0.01mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 75 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
388 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- M1 Class & Coarser
Using StandardWeights of E2 & F1class & ClassWeights (500g to10kg) & ElectronicBalance (d=0.1g) byABBA Method as perOIML R111-1
10 kg 94mg
389 MECHANICAL-WEIGHTS
Weights(Conventional Mass)- M1 Class & Coarser
Using StandardWeights of E2, F1Class (20kg to 50kg)& Electronic Balance(d=0.1g) by ABBAMethod as per OIMLR111-1
20 kg 94mg
390
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Infusion DeviceAnalyser
Using Syringe Pump& Density Meter andWeighingBalance-200g, Timerby GravimetricMethod
Flow Rate: 10 ml/hrto 1000 ml/hr 0.1%
391
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Infusion DeviceAnalyser
Using Syringe Pump& Density Meter andWeighingBalance-200g byGravimetric Method
Flow Volume: 5 ml to400 ml 1µl
392
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Leak Test Vital Sign SimulatorProsim 8
0.1 mmHg to 200mmHg 2.3mmHg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 76 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
393
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
NIBP Vital Sign SimulatorProsim 8
10 mmHg to 300mmHg
1.35 mmHg to 2.11mmHg
394MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using ResistanceBox by DirectMethod
Earth Resistance:0.001 to 2.000 Ohm 2.50%
395MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
ECG Frequency: 1 Hzto 50 Hz 0.1%
396MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using Differentialamplifier &Frequency Counter(Oscilloscope) byDirect Method
ECG Rate: 1 Hz to 5Hz (30 to 300 BPM) 0.10%
397MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using AC CurrentLoad Current Shunt,High Precision DMMby ComparisonMethod
Equipment Current:0.1 A to 8 A AC 0.60%
398MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using HV DecadeResistance Box byDirect Method
InsulationResistance: 0.5 to100.0 MOhm
1%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 77 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
399MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using MultiproductCalibrator by DirectMethod
Leakage Current: 10µA to 8 mA 1%
400MEDICALDEVICES-IMAGING/PLOTTERS
Electrical SafetyAnalyzer
Using AC PowerSource & 6.5 DMMby ComparisonMethod
Voltage: 90 V to 264V AC rms 0.60%
401MEDICALDEVICES-MONITORINGUNIT
Fetal HeartSimulator
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
ECG Frequency: 1 Hzto 100 Hz 0.10%
402MEDICALDEVICES-MONITORINGUNIT
Fetal HeartSimulator
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
Fetal Hearth Rate: 1Hz to 5 Hz (30 to300 BPM)
0.10%
403MEDICALDEVICES-MONITORINGUNIT
Fetal HeartSimulator
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
Meternal Heart Rate:1 Hz to 5 Hz (30 to300 BPM)
0.10%
404MEDICALDEVICES-MONITORINGUNIT
Fetal HeartSimulator
Using 6.5 DMM withDifferential Amplifierby Direct Method
Pressure Accuracy(TOCO): 0.1mV to5.5 mV (0 to 100mmHg)
4%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 78 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
405MEDICALDEVICES-MONITORINGUNIT
SPO2 FunctionalTester / SPO2Simulator
Using SPO2 Monitor& FunctionalVerification by DirectMethod
Heart Rate: 1 Hz to 5Hz (30 to 300 BPM) 0.10%
406MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using PressureGauge byComparison Method
Blood Pressure(NIBP- StaticPressure): 0 to 400mmHg
0.10%
407MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using 6.5 DMM byDirect Method
Cardiac Output: 13kOhm to 15 kOhm 1%
408MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using 6.5 DMM withDifferential Amplifierby Direct Method
ECG Amplitude: 50µV to 5.5 mV 1%
409MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
ECG Rate: 1 Hz to 5Hz (30 to 300 BPM) 0.10%
410MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
Fetal Heart Rate: 1Hz to 5 Hz (30 to300 BPM)
0.10%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 79 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
411MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using Power Supply& 6.5 DMM byComparison Method
Invasive BloodPressure ( :50µV to200 mV (0 to 400mmHg)
4%
412MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using PressureGauge & Timer byComparison Method
Leak Test: 0 mmHgto 2 mmHg 0.04mmHg
413MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using DifferentialAmplifier &Frequency Counter(Oscilloscope) byDirect Method
Maternal Heart Rate:0.5 Hz to 5 Hz (30 to300 BPM)
0.10%
414MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using 6.5 DMM byDirect Method
Respiration Rate: 0.1Ohm to 5 Ohm (10to 120 Brpm)
0.50%
415MEDICALDEVICES-MONITORINGUNIT
Vital Sign Simulator /Patient MonitorAnalyzers /MultiparameterSimulator
Using 6.5 DMM byDirect Method
TemperatureSimulation: 1 Ohmto 100 kOhm (0 to40°C)
1%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 80 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
416
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
DefibrillatorAnalyzer
Using DefibrillatorUnit & Defib Impulse7000DP byComparison Method
Energy: 0.1 to 400Joule (Load: 50Ohm) 1.5%
417
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
DefibrillatorAnalyzer
Using 6.5 DMM byDirect Method
Heart Rate: 0.5 Hz to5 Hz (30 to 300BPM)
0.10%
418
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
DefibrillatorAnalyzer
Using 6.5 DMM byDirect Method
Pacer Variable Load:50 Ohm to 1500Ohm
0.50%
419
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Electro SurgicalAnalyzer
Using current coilwith true RMS meterby direct method
Analyzer outputcurrent: 0.5mA to5500 mA
1%
420
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Electro SurgicalAnalyzer
Using 6.5 DMM byDirect Method
Analyzer output loadresi 0.1Ohm to 5200Ohm
0.5%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 81 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
421
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Electro SurgicalAnalyzer
Using current coilwith true RMS meterby direct method
Analyzer outputpower: 1 W to 500 W 0.60%
422
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Electro SurgicalAnalyzer
Using 6.5 DMM bydirect method
Contact qualitymonitor ( 0.1Ohm to475 Ohm
0.50%
423
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Electro SurgicalAnalyzer
Using current coilwith true RMS meterby direct method
Vessel sealingmeasuremen 100mA to 1100 mA
1%
424
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Gas Flow AnalyzerUsing PressureGauge byComparison Method
Barometric Pressure:12 psi to 16 psi 0.20%
425
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Gas Flow AnalyzerUsing Mass FlowController byComparison Method
Flow Rate: Up to 300slm 0.60%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 82 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
426
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Gas Flow AnalyzerUsing PressureGauge byComparison Method
Pressure: 0 to 100psi 0.10%
427
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Incubator AnalyzerUsing DigitalTemperatureHumidity Meter byComparison Method
Humidity: 30 to 90%RH 3%
428
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Incubator AnalyzerUsing Sound LevelCalibrator by DirectMethod
Sound Level: 94 dB 1.1dB
429
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Incubator AnalyzerUsing RTD Sensorwith Indicator byComparison Method
Temperature: 10 to50 °C 0.5°C
430THERMAL-SPECIFIC HEAT& HUMIDITY
Humidity /Thermohygrometer@25°C
Using HumidityChamber withDigital Temp. &Humidity Indicatorwith Sensor
25 %RH to 95 %RH 2.18%RH
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 83 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
431 THERMAL-TEMPERATURE
Glass TypeThermometers
Using SPRT & Flukemake Readout, LowTemperature Bathh(-45°C to 50°C) & OilBath by comparisonmethod.
-40 °C to 50 °C 0.06°C
432 THERMAL-TEMPERATURE
Glass TypeThermometers
Using SPRT & Flukemake Readout, LowTemperature Bath &Oil Bath (Amb. to250°C) bycomparison method
50 °C to 250 °C 0.16°C
433 THERMAL-TEMPERATURE
Glass TypeThermometers
Using SPRT & Flukemake Readout, LowTemperature Bath(-80°C to 50°C) & OilBath by comparisonmethod
-80 °C to -40 °C 0.10°C
434 THERMAL-TEMPERATURE
Indicator of BlackBody - Source orFurnace
Using Non-ContactPyrometer bycomparison method
50 °C to 500 °C 2.73°C
435 THERMAL-TEMPERATURE
Indicator of BlackBody Source /Furnace
Using Non-ContactPyrometer bycomparison method
500 °C to 1200 °C 3.36°C
436 THERMAL-TEMPERATURE
Indicator of Dry WellBlocks, MuffleFurnace
Using Standard RType TC withIndicator bycomparison method.
650 °C to 900 °C 1.86°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 84 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
437 THERMAL-TEMPERATURE
Indicator of Dry WellBlocks, MuffleFurnace
Using Standard RType TC withIndicator bycomparison method
900 °C to 1200 °C 2.3°C
438 THERMAL-TEMPERATURE
Indicator of LiquidBaths, Dry WellBlocks,Incubators(non-medical purpose),Ovens
Using SPRT & Flukemake Readout bycomparison method
-40 °C to 50 °C 0.10°C
439 THERMAL-TEMPERATURE
Indicator of LiquidBaths, Dry WellBlocks,Incubators(non-medical purpose),Ovens
Using SPRT & Flukemake Readout bycomparison method
50 °C to 250 °C 0.10°C
440 THERMAL-TEMPERATURE
Indicator of LiquidBaths, Dry WellBlocks,Incubators(non-medical purpose),Ovens
Using SPRT & Flukemake Readout bycomparison method
-80 °C to -40 °C 0.10°C
441 THERMAL-TEMPERATURE
Indicator of LiquidBaths, Dry WellBlocks, Ovens
Using SPRT & Flukemake Readout bycomparison method
250 °C to 650 °C 0.4°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 85 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
442 THERMAL-TEMPERATURE
Indicator ofRefrigerators,Incubators(non-medical purpose),Ovens, Furnace, DryWell Blocks, LiquidBath
Using Standard PRTwith MiliK Indicatorby comparisonmethod
-35 °C to 50 °C 0.10°C
443 THERMAL-TEMPERATURE
Infrared / Non-ContactThermometers
Using Non-ContactPyrometer & BlackBody Furnace (e=0.95) (Amb to 500°Cby ComparisonMethod
50 °C to 500 °C 2.6°C
444 THERMAL-TEMPERATURE
Infrared / Non-ContactThermometers
Using Non-ContactPyrometer withBlack Body Furnace(e= 0.95) (300°C to1200°C) byComparison Method
500 °C to 1200 °C 3.72°C
445 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using SPRT & Flukemake readout, LowTemperature Bath &Oil Bath (Amb to650°C) bycomparison method
250 °C to 650 °C 0.35°C
446 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using SPRT & Flukemake readout, LowTemperature Bath &Oil Bath (- 45°C to50°C)by comparisonmethod
-40 °C to 50 °C 7m°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 86 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
447 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using SPRT & Flukemake readout, LowTemperature Bath &Oil Bath (Amb to250°C) bycomparison method
50 °C to 250 °C 0.10°C
448 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using Standard RType TC withIndicator & Dry WellBath (150°C to1200°C) bycomparison method
650 °C to 900 °C 1.98°C
449 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using SPRT & Flukemake readout, LowTemperature Bath &Oil Bath (-80°C to50°C) by comparisonmethod.
-80 °C to -40 °C 0.10°C
450 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using Standard RType TC withIndicator & Dry WellBath (150°C to1200°C) bycomparison method
900 °C to 1200 °C 2.3°C
451 THERMAL-TEMPERATURE
SPRT's, PRT's, RTD's& RTD Based DigitalThermometer, TC &TC Based Indicators
Using Fluke makeMaintenanceApparatus 9210,TPW Cell & Flukemake readout bycomparison method
0.01 °C 2.07m°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 87 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
452 THERMAL-TEMPERATURE
SPRT's, PRT's, RTD's& RTD Based DigitalThermometer, TC &TC Based Indicators
Using Fluke makeMaintenanceApparatus 9260,Indium Cell & Flukemake readout fixpoint by comparisonmethod
156.598 °C 3.52m°C
453 THERMAL-TEMPERATURE
SPRT's, PRT's, RTD's& RTD Based DigitalThermometer, TC &TC Based Indicators
Using LiquidNitrogen, SPRT &Fluke make readoutat fix point
-196.075 °C 8.4m°C
454 THERMAL-TEMPERATURE
SPRT's, PRT's, RTD's& RTD Based DigitalThermometer, TC &TC Based Indicators
Using Fluke makeMaintenanceApparatus 9260, TinCell & Fluke makereadout fix point bycomparison method.
231.928 °C 3.99m°C
455 THERMAL-TEMPERATURE
SPRT's, PRT's, RTD's& RTD Based DigitalThermometer, TC &TC Based Indicators
Using Fluke makeMaintenanceApparatus 9260,Zinc Cell & Flukemake readout fixpoint by comparisonmethod
419.527 °C 5.24m°C
456 THERMAL-TEMPERATURE
SPRT's, PRT's, RTD's& RTD Based DigitalThermometer, TC &TC Based Indicators
Using Fluke makeMaintenanceApparatus 9260,Aluminium Cell &Fluke make readoutfix point bycomparison method.
660.323 °C 8.06m°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 88 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
Site Facility
1
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
3 Phase ActiveEnergy (50Hz) (60Vto 240V)
Using 3 Phase PowerTesting Instrumentby Comparison
AC Current(0.1 to5A) @UPF 0.1%
2
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to10kHz)
Using 5790A ACMeasurementStandard andA40/A40A Shunts byAC/DC TransferMethod
2 mA to 20 A 0.023 % to 0.06 %
3
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to1kHz)
Using 8508A DMMby Direct Method 10 µA to 200 mA 0.3 % to 0.05 %
4
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to1kHz)
Using 8508A DMMby Direct Method 2 A to 20 A 0.07 % to 0.13 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 89 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
5
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (10Hz to1kHz)
Using 8508A DMMby Direct Method 200 mA to 2 A 0.05 % to 0.07 %
6
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Current (50Hz)Using HC 3100Precision PowerTesting Instrumentby Direct Method
20 A to 100 A 0.3 % to 0.1 %
7
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.12 W to 0.72 kW(0.1 PF) 3.35 % to 0.4 %
8
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.24 W to 1.44 kW(0.2 PF) 2.92 % to 0.24 %
9
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.48 W to 2.88 kW(0.4 PF) 2.92 % to 0.16 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 90 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
10
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.72 W to 4.32 kW(0.6 PF) 2.92 % to 0.13 %
11
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
0.96 W to 5.76 kW(0.8 PF) 2.92 % to 0.12 %
12
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Power 50Hz(120V, 240V)
Power AnalyserWT3000 by DirectMethod
1.2 W to 7.2 kW(UPF) 2.92 % to 0.08 %
13
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
1 mV to 20 mV 0.72 % to 0.013 %
14
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 mV to 200 mV 0.017 % to 0.004 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 91 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
15
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 V to 60 V 0.008 % to 0.0035 %
16
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (10Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
200 mV to 20 V 0.008 % to 0.003 %
17
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to100kHz)
Using 5790A ACMeasurementStandard by DirectMethod
60 V to 600 V 0.0035 % to 0.06 %
18
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to1MHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 mV to 200 mV 0.013 % to 0.25 %
19
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to1MHz)
Using 5790A ACMeasurementStandard by DirectMethod
200 mV to 20 V 0.003 % to 0.13 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 92 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
20
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to1MHz)
Using 5790A ACMeasurementStandard by DirectMethod
6 mV to 20 mV 0.09 % to 0.34 %
21
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to20kHz)
Using 5790A ACMeasurementStandard by DirectMethod
600 V to 1000 V 0.0038 % to 0.01 %
22
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (1kHz to300kHz)
Using 5790A ACMeasurementStandard by DirectMethod
20 V to 60 V 0.003 % to 0.02 %
23
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (40Hz to1kHz)
Using 5790A ACMeasurementStandard by DirectMethod
60 V to 1000 V 0.008 % to 0.004 %
24
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
AC Voltage (HighVoltage)
Using HV Dividerwith KV Meter byDirect Method
1 kV to 100 kV 1.8 % to 2 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 93 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
25
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Capacitance (100Hz)Using LCR Meter43100 by DirectMethod
10 µF to 100 µF 0.12 % to 0.5 %
26
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Capacitance (1kHz)Using LCR Meter43100 by DirectMethod
1 pF to 1 mF 0.68 % to 0.17 %
27
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Inductance (1kHz)Using LCR Meter43100 by DirectMethod
100 µH to 10 H 0.32 % to 0.17 %
28
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Oscilloscope -Bandwidth
Using 5502ACalibrator by DirectMethod
Up to 600 MHz 4%
29
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Phase AngleUsing Phase AngleMeter by DirectMethod
0 to 120 ° 1.11 ° to 0.61 °
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 94 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
30
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Phase AngleUsing Phase AngleMeter by DirectMethod
120 ° to 360 ° 0.61 ° to 1.11 °
31
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Power FactorUsing PowerAnalyser WT3000 byDirect Method
0.1 to UPF 0.03PF
32
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Power Single Phase(50Hz) (60V to240V)
Using 3 Phase PowerTesting Instrumentby Comparison
1 A to 100 A 0.1%
33
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method 1 m ohm to 1 ohm 0.61 % to 0.006 %
34
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method 1 ohm to 10 ohm 0.006 % to 0.0013 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 95 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
35
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method
10 M ohm to 100 Mohm 0.0031 % to 0.02 %
36
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method 10 ohm to 10 M ohm 0.0013 % to 0.0031
%
37
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
Resistance Using 8508A DMMby Direct Method
100 M ohm to 10 Gohm 0.02 % to 0.23 %
38
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Measure)
RF Power (WithoutVSWR) (1MHz to1GHz)
Using RFMillivoltmeter URV55by Direct Method
-30 dBm to 15 dBm 0.25 dBm to 1.3dBm
39
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (10Hz to10kHz)
Using 5502ACalibrator by DirectMethod
33 mA to 3 A 0.582 % to 2 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 96 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
40
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
10 µA to 200 mA 0.8 % to 0.06 %
41
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (1kHz to10kHz)
Using 5720ACalibrator by DirectMethod
20 mA to 200 mA 0.06 % to 0.133 %
42
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (1kHz to5kHz)
Using 5502ACalibrator by DirectMethod
2 A to 20 A 0.5 % to 3.5 %
43
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (40Hz to10kHz)
Using 5720ACalibrator by DirectMethod
200 mA to 2 A 0.025 % to 1.7 %
44
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (50Hz to1kHz)
Using 5720ACalibrator by DirectMethod with 52120AAmplifier by DirectMethod
2 A to 20 A 0.5 % to 0.11 %
45
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (50Hz to1kHz)
Using 5720ACalibrator by DirectMethod with 52120AAmplifier by DirectMethod
20 A to 100 A 0.5 % to 0.11 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 97 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
46
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Current (50Hz)Using 5502ACalibrator withCurrent Coil byDirect Method
100 A to 1000 A 0.703%
47
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
1 mV to 2 mV 0.57 % to 0.276 %
48
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
2 mV to 20 mV 0.276 % to 0.03 %
49
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
20 mV to 200 mV 0.03 % to 0.018 %
50
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
20 V to 200 V 0.007 % to 0.008 %
51
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (10Hz to1kHz)
Using 5720ACalibrator by DirectMethod
200 mV to 20 V 0.018 % to 0.007 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 98 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
52
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to100kHz)
Using 5720ACalibrator by DirectMethod
10 V to 100 V 0.005 % to 0.02 %
53
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to10kHz)
Using 5502ACalibrator by DirectMethod
200 V to 1000 V 0.06 % to 0.14 %
54
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
1 mV to 2 mV 0.57 % to 2.3 %
55
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
2 mV to 20 mV 0.26 % to 1.3 %
56
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
20 mV to 200 mV 0.03 % to 1.3 %
57
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to1MHz)
Using 5720ACalibrator by DirectMethod
200 mV to 10 V 0.007 % to 0.37 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 99 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
58
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (1kHz to20kHz)
Using 5720ACalibrator by DirectMethod
100 V to 200 V 0.01%
59
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
AC Voltage (50Hz to1kHz)
Using 5720ACalibrator by DirectMethod
200 V to 1000 V 0.008 % to 0.013 %
60
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
1 µF to 90 µF 0.88 % to 1.18 %
61
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
1 nF to 9 nF 1.9 % to 1.2 %
62
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
10 nF to 900 nF 1.2 % to 1.8 %
63
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using CapacitanceDecade box byDirect Method
100 pF to 900 pF 7 % to 1.86 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 100 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
64
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Capacitance (1kHz)Using 5502ACalibrator by DirectMethod
90 µF to 110 mF 0.5 % to 1.5 %
65
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Inductance (1kHz)Using DecadeInductance Box byDirect Method
1 mH to 10 H 3.50%
66
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ODD Harmonicsdistortion (Current)Upto 41st
Using FlukeMultiproductCalibrator 5502A byDirect Method
100 mA to 6 A 0.75%
67
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ODD Harmonicsdistortion (Voltage)Upto 41st order
Using FlukeMultiproductCalibrator 5502A byDirect Method
100 mV to 60 V 0.75%
68
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Oscilloscope -Horizontal Deflection(Time Base)
Using 5502ACalibrator by DirectMethod
2 nS to 2 S 0.1 % to 0.3 %
69
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Oscilloscope -Vertical Deflection(Square Wave@1kHz Freq. & DCFunction)
Using 5502ACalibrator by DirectMethod
10 mV to 120 V 0.5%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 101 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
70
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.1PF) (120V to240V@ 0.1 to 20A)
Using 5502ACalibrator by DirectMethod
1.2 W to 480 W 5.0%
71
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.2PF) (120V [email protected] to 20A)
Using 5502ACalibrator by DirectMethod
2.4 W to 960 W 2.93%
72
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.5PF) (120V to240V & 0.1 to 20A)
Using 5502ACalibrator by DirectMethod
12 W to 1200 W 1.17 % to 1.2 %
73
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat 0.8PF) (120V to240V @ 0.1 to 20A)
Using 5502ACalibrator by DirectMethod
9.6 W to 3840 W 2.93%
74
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power 1 Phase (50Hzat UPF) (120V to240V @ 0.01A to20A)
Using 5502ACalibrator by DirectMethod
1.1 W to 4800 W 2.92 % to 0.75 %
75
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Power FactorUsing 5502ACalibrator by DirectMethod
0.25 PF to 1 PF 0.04PF
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 102 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
76
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using DecadeResistance Box
0.001 ohm to 0.01ohm 2.6%
77
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using DecadeResistance Box 0.01 ohm to 0.1 ohm 1.15%
78
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using DecadeResistance Box 0.1 ohm to 1 ohm 1.15 % to 0.8 %
79
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using Std Resistorby Direct Method 1 G ohm 0.034%
80
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using Decade MegaOhm Box 1 G ohm to 1 T ohm 1.2 % to 4.71 %
81
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1 kilo ohm 0.0012%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 103 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
82
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1 mega ohm 0.003%
83
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing FixedResistnace by DirectMethod
1 mili ohm 0.04%
84
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1 ohm 0.012%
85
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
1 ohm to 30 ohm 1.17 % to 0.07 %
86
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1.9 kilo ohm 0.0013%
87
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1.9 mega ohm 0.003%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 104 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
88
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
1.9 ohm 0.011%
89
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
10 kilo ohm 0.0012%
90
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
10 mega ohm 0.005%
91
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing FixedResistnace by DirectMethod
10 mili ohm 0.03%
92
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
10 ohm 0.003%
93
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
100 kilo ohm 0.0012%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 105 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
94
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
100 mega ohm 0.013%
95
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing FixedResistnace by DirectMethod
100 mili ohm 0.02%
96
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
100 ohm 0.0012%
97
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
19 kilo ohm 0.0012%
98
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
19 mega ohm 0.006%
99
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
19 ohm 0.003%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 106 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
100
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
190 kilo ohm 0.0013%
101
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5720ACalibrator by DirectMethod
190 ohm 0.0012%
102
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
290 M ohm to 1 Gohm 0.5 % to 1.79 %
103
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
3 M ohm to 30 Mohm 0.07 % to 0.1 %
104
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
30 M ohm to 290 Mohm 0.1 % to 0.5 %
105
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
30 ohm to 300 ohm 0.072 % to 0.019 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 107 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
106
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
Resistance Using Decade MegaOhm Box
300 M ohm to 1 Gohm 1.17%
107
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ) (Source)
ResistanceUsing 5502ACalibrator by DirectMethod
300 ohm to 300 kohm 0.019 % to 0.013 %
108
ELECTRO-TECHNICAL-ALTERNATINGCURRENT (< 1GHZ)(Source,Measure)
ResistanceUsing 5502ACalibrator by DirectMethod
300 k ohm to 3 Mohm 0.013 % to 0.07 %
109
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing Picoammeter6485 by DirectMethod
0.02 µA to 1 µA 0.55%
110
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 1 µA to 10 µA 0.06 % to 0.006 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 108 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
111
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 1 A to 20 A 0.021 % to 0.065 %
112
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing Picoammeter6485 by DirectMethod
1 nA to 20 nA 0.94%
113
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 10 µA to 10 mA 0.006 % to 0.0023 %
114
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Current Using 8508A DMMby Direct Method 10 mA to 1 A 0.0023 % to 0.021 %
115
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing Power MeterWT3000 by DirectMethod
20 A to 30 A 0.15%
116
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC CurrentUsing DC Shunt and8508A DMM byDirect Method
30 A to 100 A 0.9%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 109 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
117
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Power (1V to1000V) (100mA to20A)
Using PowerAnalyser WT3000 byDirect Method
0.1 mW to 20 kW 3.8 % to 0.3 %
118
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage Using 8508A DMMby Direct Method 0.1 mV to 10 mV 0.13 % to 0.013 %
119
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage Using 8508A DMMby Direct Method 10 mV to 100 mV 0.013 % to 0.0008 %
120
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage Using 8508A DMMby Direct Method 100 mV to 1000 V 0.0008%
121
ELECTRO-TECHNICAL-DIRECTCURRENT(Measure)
DC Voltage (HighVoltage)
Using HV Divider byDirect Method 1 kV to 20 kV 1.6 % to 2.1 %
122
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
1 µA to 10 µA 0.82 % to 0.09 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 110 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
123
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
10 µA to 200 µA 0.09 % to 0.008 %
124
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5502ACalibrator withCurrent Coil byDirect Method
100 A to 1000 A 0.802%
125
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator with52120A Amplifier byDirect Method
2 A to 20 A 0.023 % to 0.05 %
126
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator with52120A Amplifier byDirect Method
20 A to 100 A 0.05 % to 0.08 %
127
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
20 mA to 200 mA 0.0044 % to 0.006 %
128
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
200 µA to 20 mA 0.008 % to 0.0044 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 111 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
129
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC CurrentUsing 5720ACalibrator by DirectMethod
200 mA to 2 A 0.006 % to 0.01 %
130
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC Power @1V to1000V, 1A to 20A
Using MuliproductCalibrator 5502Awith Power Option
1 W to 20 kW 2.93 % to 0.2 %
131
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
0.1 mV to 1 mV 0.75 % to 0.075 %
132
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
1 mV to 10 mV 0.075 % to 0.006 %
133
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
10 mV to 100 mV 0.006 % to 0.0014 %
134
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
100 mV to 100 V 0.0014 % to 0.0007%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 112 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
135
ELECTRO-TECHNICAL-DIRECTCURRENT(Source)
DC VoltageUsing 5720ACalibrator by DirectMethod
100 V to 1000 V 0.0007 % to 0.0009%
136
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (B-Type)
Using 8505A DMMby Direct Method 200 °C to 1820 °C 0.061°C
137
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (C-Type)
Using 8505A DMMby Direct Method 200 °C to 2320 °C 0.022°C
138
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (E-Type)
Using 8505A DMMby Direct Method -200 °C to 1000 °C 0.012°C
139
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (J-Type)
Using 8505A DMMby Direct Method -210 °C to 1200 °C 0.012°C
140
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (K-Type)
Using 8505A DMMby Direct Method -210 °C to 1372 °C 0.012°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 113 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
141
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (L-Type)
Using 8505A DMMby Direct Method -200 °C to 900 °C 0.018°C
142
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (N-Type)
Using 8505A DMMby Direct Method -200 °C to 1300 °C 0.014°C
143
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (R-Type)
Using 8505A DMMby Direct Method -50 °C to 1768 °C 0.054°C
144
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (RTD)
Using 8505A DMMby Direct Method -200 °C to 850 °C 0.01°C
145
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (S-Type)
Using 8505A DMMby Direct Method -50 °C to 1768 °C 0.031°C
146
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (T-Type)
Using 8505A DMMby Direct Method -200 °C to 400 °C 0.01°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 114 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
147
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Measure)
TemperatureSimulation (U-Type)
Using 8505A DMMby Direct Method -200 °C to 600 °C 0.012°C
148
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (B-Type)
Using 5720ACalibrator by DirectMethod
200 °C to 1820 °C 0.232°C
149
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (C-Type)
Using 5720ACalibrator by DirectMethod
200 °C to 2320 °C 0.037°C
150
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (E-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 1000 °C 0.28°C
151
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (J-Type)
Using 5720ACalibrator by DirectMethod
-210 °C to 1200 °C 0.029°C
152
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (K-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 1372 °C 0.036°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 115 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
153
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (L-Type)
Using 5720ACalibrator by DirectMethod
-200 °C to 900 °C 0.016°C
154
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (N-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 1300 °C 0.047°C
155
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (R-Type)
Using 5720ACalibrator by DirectMethod
-50 °C to 1768 °C 0.155°C
156
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (RTD)
Using 5502ACalibrator by DirectMethod
-200 °C to 800 °C 0.25°C
157
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (S-Type)
Using 5720ACalibrator by DirectMethod
-50 °C to 1768 °C 0.12°C
158
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (T-Type)
Using 5720ACalibrator by DirectMethod
-270 °C to 400 °C 0.031°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 116 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
159
ELECTRO-TECHNICAL-TEMPERATURESIMULATION(Source)
TemperatureSimulation (U-Type)
Using 5720ACalibrator by DirectMethod
-200 °C to 600 °C 0.026°C
160
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
1 hr to 5 hr 0.14 s to 6 s
161
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
1 s to 60 s 0.0252 s to 0.036 s
162
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
5 hr to 24 hr 6 s to 21 s
163
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
60 s to 1 hr 0.03 s to 0.14 s
164
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
Digital/Analog Timer/ Stop Watches/TimeInterval Meter/On-offTimer/BreakerTimer/Relay Timer
Using Time IntervalMeter bycomparison Method
200 ms to 1 s 0.0252s
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 117 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
165
ELECTRO-TECHNICAL-TIME &FREQUENCY(Measure)
FrequencyUsing Timer/CounterCNT91 by DirectMethod
1 Hz to 3 GHz 0.002 % to 0.0008 %
166
ELECTRO-TECHNICAL-TIME &FREQUENCY(Source)
FrequencyUsing 5502ACalibrator by DirectMethod
1 Hz to 2 MHz 0.004%
167
ELECTRO-TECHNICAL-TIME &FREQUENCY(Source)
FrequencyUsing 5502ACalibrator by DirectMethod
2 MHz to 600 MHz 0.003%
168FLUID FLOW-FLOWMEASURINGDEVICES
Flow rate (AIR/N2)Using Alicat MassFlow Controller bycomparison method
0.5 slm to 5 slm 0.04slm
169FLUID FLOW-FLOWMEASURINGDEVICES
Flow rate (AIR/N2)Using Alicat MassFlow Controller bycomparison method
5 slm to 50 slm 0.4slm
170FLUID FLOW-FLOWMEASURINGDEVICES
Flow rate (AIR/N2)Using Alicat MassFlow Controller bycomparison method
50 sccm to 500sccm 4sccm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 118 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
171FLUID FLOW-FLOWMEASURINGDEVICES
Flow rate (Air/N2)Using Alicat MassFlow Controller bycomparison method
50 slm to 100 slm 0.8slm
172FLUID FLOW-FLOWMEASURINGDEVICES
Flow Rate (Water)Using GE-PT 878Ultrasonic Clampwith Indicator byComparison Method
1.2 m3/hr to 3000m3/hr 3%
173FLUID FLOW-FLOWMEASURINGDEVICES
Fluid Flow (Air/N2)Using Alicat MassFlow Controller bycomparison method
100 slm to 500 slm 4slm
174FLUID FLOW-FLOWMEASURINGDEVICES
Fluid Flow (AIR/N2)Using Alicat MassFlow Controller bycomparison method
5 sccm to 5 slm 0.7%
175MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
10 RPM to 100 RPM 0.63RPM
176MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
100 RPM to 1000RPM 1.52RPM
177MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
1000 RPM to 5000RPM 1.97RPM
178MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
10000 RPM to 60000RPM 3.71RPM
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 119 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
179MECHANICAL-ACCELERATIONAND SPEED
Centrifuge / RPMSource
Using DigitalTachometer byComparison Method
5000 RPM to 10000RPM 2.85RPM
180MECHANICAL-ACCELERATIONAND SPEED
Vibration Meter /Accelerometer withTransducer
Using VibrationCalibrator byComparison Method
Acceleration: Up to95m/s2 (50Hz to5000Hz)
5.5%
181MECHANICAL-ACCELERATIONAND SPEED
Vibration Meter /Accelerometer withTransducer
Using VibrationCalibrator byComparison Method
Displacement: Up to1250µm (50Hz to1000Hz)
4.4%
182MECHANICAL-ACCELERATIONAND SPEED
Vibration Meter /Accelerometer withTransducer
Using VibrationCalibrator byComparison Method
Velocity: Up to239mm/s (50Hz to5000Hz)
4.1%
183
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier HeightGauge(L.C.=0.0001mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
300 mm to 600 mm 7.3µm
184
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier HeightGauge(L.C.=0.0001mm)
Using CaliperChecker Slip GaugeSet Circular SteelLength Bar Grade '0'by ComparisonMethod
600 mm to 1000mm 8.3µm
185
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial / Digimatic /Vernier HeightGauge(L.C.=0.0001mm)
Using Slip Gauge SetGrade '0' CircularSteel Length BarCaliper Checker byComparison Method
Up to 300 mm 3.4µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 120 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
186
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Dial CalibrationTester(L.C.=0.0001mm)
Using ElectronicComparator withProbe byComparison Method
Up to 25 mm 1.3µm
187
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Microscope(Magnification)
Using Glass Scale byComparison Method Up to 1000X 0.28%
188
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge(Straightness)
Using Slip Gauge SetGrade '0' 0 to 1000 mm 13.1µm
189
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Straight Edge(Straightness)
Using ( Slip GaugeSet Grade '0' up to45 mm width) (Electeonic levelmore than 45 mmwidth)
1000 mm to 2000mm 21.6µm
190
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Surface Plate Using ElectronicLevel
2500 mm to 2500mm
1.4*sqrt[(L+W)/125]µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 121 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
191
MECHANICAL-DIMENSION(BASICMEASURINGINSTRUMENT,GAUGE ETC.)
Tape & ScaleCalibrator (L.C.=0.005mm)
Using Slip Gauge Setby ComparisonMethod
Up to 1000 mm 10.5µm
192MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Length MeasuringMachine (L.C.=0.0001mm)
Using Slip Gauge SetGrade 'K' byComparison Method
Up to 100 mm 0.51µm
193MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector(Angular L.C.=1sec)
Using AngularGraticule / AngleGauge Set byComparison Method
0 to 360 ° 2.35min
194MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector(LinearL.C.=0.001mm)
Using Glass Scale /Gauge Block byComparison Method
Up to 200 mm 5.62µm
195MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Profile Projector(Magnification)
Using Glass Scale &Digimatic Caliper byComparison Method
10X, 20X, 50X, 100X 0.28%
196MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)
Slip GaugeCalibrator(L.C.=0.01µm)
Using Bridge SlipGauge Set K-Gradeby ComparisonMethod
0 to 100 mm 0.15µm
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 122 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
197MECHANICAL-MOBILE FORCEMEASURINGSYSTEM
Verification ofUniaxial TestingMachine (Universal,Tensile,Compression TestingMachines)
Using Class 0 orclass 1 Loadcell withIndicator as per IS1828 part I 2015 &ISO 7500-I
Compression: 10 Nto 100 kN 0.34%
198MECHANICAL-MOBILE FORCEMEASURINGSYSTEM
Verification ofUniaxial TestingMachine (Universal,Tensile,Compression TestingMachines)
Using Class 0 orclass 1 Loadcell withIndicator as per IS1828 part I 2015 &ISO 7500-I
Tension: 10 N to 100kN 0.34%
199MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,PressureTransmitter,Pressure Switches.
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
100 bar (g) to 1000bar (g) 0.57bar
200MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,PressureTransmitter,Pressure Switches.
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
20 bar (g) to 160 bar(g) 0.07bar
201MECHANICAL-PRESSUREINDICATINGDEVICES
Hydraulic PressureIndicating Devices,PressureTransmitter,Pressure Switches.
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
40 bar (g) to 400 bar(g) 0.37bar
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 123 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
202MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using MultifunctionCalibrator withExternal Sensor
0 to 10 mbar (g) 0.021mbar
203MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using Low PressureCalibrator
0 mbar (g) to 200mbar (g) 0.17mbar
204MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
0.2 bar (g) to 2 bar(g) 0.003bar
205MECHANICAL-PRESSUREINDICATINGDEVICES
Pneumatic PressureIndicating Devices,PressureTransmitter,Pressure Switches
Using MultifunctionCalibrator withInternal & ExternalSensor byComparison Method(DKD-R-6-1)
2 bar (g) to 20 bar(g) 0.02bar
206MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using MultifunctionCalibrator withExternal Sensor
0 to -10 mbar 0.021mbar
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 124 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
207MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using Low PressureCalibrator, DigitalVacuum Gauge byComparison Method(DKD-R-6-1)
0 to -200 mbar (g) 0.176mbar
208MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using Low PressureCalibrator, DigitalVacuum Gauge byComparison Method(DKD-R-6-1)
-0.2 bar (g) to -0.95bar (g) 1.0mbar
209MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using MultifunctionCalibrator withExternal Sensor
-0.2 bar to -0.95 bar 1.0mbar
210MECHANICAL-PRESSUREINDICATINGDEVICES
Vacuum IndicatingDevices, Vacuum,Transmitter, VacuumSwitches
Using MultifunctionCalibrator withExternal Sensor
-10 mbar to -200mbar 0.2mbar
211MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.01mg)
Using StandardWeight of E1 Class(1mg to 500g), E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
1 mg to 100 g 0.03mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 125 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
212MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.1g)
Using StandardWeight of E2 ClassWeights (1mg to10kg), F1 & M1Class Weights (500gto 20kg) byComparison Methodas per OIML R76-1
10 kg to 30 kg 0.24g
213MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.1g)
Using StandardWeight of E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
5 kg to 10 kg 0.09g
214MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=0.1mg)
Using StandardWeight of E1 Class(1mg to 500g), E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
100 g to 200 g 0.13mg
215MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=1.0mg)
Using StandardWeight of E1 Class(1mg to 500g), E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
200 g to 1000 g 0.91mg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 126 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
216MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=10mg)
Using StandardWeight of E2Weights (1mg to10kg) byComparison Methodas per OIML R76-1
1 kg to 5 kg 8.20mg
217MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1, M1Class & CI Weights(500g to 20kg) byComparison Methodas per OIML R76-1
100 kg to 200 kg 18.70g
218MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1, M1Class & CI Weights(500g to 20kg) byComparison Methodas per OIML R76-1
200 kg to 300 kg 28.25g
219MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1 & M1Class Weights (500gto 20kg) byComparison Methodas per OIML R76-1
30 kg to 50 kg 14.47g
220MECHANICAL-WEIGHINGSCALE ANDBALANCE
Electronic WeighingBalance (d=20g)
Using StandardWeight of F1 & M1Class Weights (500gto 20kg) byComparison Methodas per OIML R76-1
50 kg to 100 kg 14.74g
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 127 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
221
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Flow Gas Flow AnalyzerVT Plus HF 2 lpm to 20 lpm 2.3lpm
222
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Flow using gas flowanalyser vt plus hf 4 lpm to 60 lpm 1.1lpm
223
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
FlowGas Flow AnalyzerVT Plus HF & RTDSensor withIndicator
50 lpm 2.3%
224
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Flow Rate Infusion DeviceAnalyzer IDA 5
0.1 ml/hr to 1500ml/hr 1.32%
225
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Leak Test Vital Sign SimulatorProsim 8
0.1 mmHg to 200mmHg 2.3mmHg
226
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
NIBP Vital Sign SimulatorProsim 8
10 mmHg to 300mmHg
1.35 mmHg to 2.11mmHg
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 128 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
227
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Occlusion Infusion DeviceAnalyzer IDA 5 0 psi to 45 psi 0.5psi
228
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Oxygen Percentage Gas Flow AnalyzerVT Plus HF 0 % to 100 % 2.4%
229
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Pressure (PEEP) Gas Flow AnalyzerVT Plus HF
4 cmH2O to 30cmH2O 1.2cmH2O
230
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Respiration Rate Gas Flow AnalyzerVT Plus HF 4 bpm to 100 bpm 1.3bpm
231
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Vacuum (Pressure) Pressure Gauge 0 bar to -1 bar 1.1%
232
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Volume Infusion DeviceAnalyzer IDA 5 0.06 ml to 9999 ml 1.4%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 129 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
233
MEDICALDEVICES-DISCHARGEEQUIPMENT/DEVICES
Volume Accuracy Gas Flow AnalyzerVT Plus HF 0.1 ml to 1000 ml 3.6%
234MEDICALDEVICES-IMAGING/PLOTTERS
Chasis LeakageUsing electricalSafety Analyser ESA615 by DirectMethod
10 uA to 10 mA 5%
235MEDICALDEVICES-IMAGING/PLOTTERS
Chasis Leakage Electrical SafetyAnalyzer ESA 615
Less than 100µA NC,to Less than 500µASFC
5%
236MEDICALDEVICES-IMAGING/PLOTTERS
Ground WireResistance
Using electricalSafety Analyser ESA615 by DirectMethod
0.1 ohms to 2 ohms 2.6%
237MEDICALDEVICES-IMAGING/PLOTTERS
Ground WireResistance
Electrical SafetyAnalyzer ESA 615 Less than 3 Ohm 2%
238MEDICALDEVICES-IMAGING/PLOTTERS
Heart Rate Vital Sign SimulatorProsim 8 10 bpm to 300 bpm 1.2%
239MEDICALDEVICES-IMAGING/PLOTTERS
Insulation Test(optional 500V)
Using electricalSafety Analyser ESA615 by DirectMethod
0.5 Mohms to 100Mohms 2%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 130 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
240MEDICALDEVICES-IMAGING/PLOTTERS
Insulation Test(Optional 500V)
Electrical SafetyAnalyzer ESA 615 Less than 2 Ohm 2%
241MEDICALDEVICES-IMAGING/PLOTTERS
Lux Lux Meter 25000 Lux to200000 lux 2.81Lux
242MEDICALDEVICES-IMAGING/PLOTTERS
Patient LeadLeakage (Mains onPatient applied partIsolation Test)
Using electricalSafety Analyser ESA615 by DirectMethod
10 uA to 10 mA 5%
243MEDICALDEVICES-IMAGING/PLOTTERS
Patient LeadLeakage Current(Mains on Patientapplied partIsolation Test)
Electrical SafetyAnalyzer ESA 615
Less than 100µA BF,Less than 1000µA CF 5%
244MEDICALDEVICES-IMAGING/PLOTTERS
Patient LeakageUsing electricalSafety Analyser ESA615 by DirectMethod
1 µA to 10 mA 5%
245MEDICALDEVICES-MONITORINGUNIT
Amplitude Vital Sign SimulatorProsim 8 ±5 % 4.3%
246MEDICALDEVICES-MONITORINGUNIT
Heart Rate Vital Sign SimulatorProsim 8 20 bpm to 300 bpm 1.2%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 131 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
247MEDICALDEVICES-MONITORINGUNIT
IABP Vital Sign SimulatorProsim 8
0 mmHg to 300mmHg 1.2%
248MEDICALDEVICES-MONITORINGUNIT
NIBP (Dynamic) Vital Sign SimulatorProsim 8
15 mmHg to 255mmHg 1.5%
249MEDICALDEVICES-MONITORINGUNIT
NIBP Leak Test Vital Sign SimulatorProsim 8
Less than or equal to15 mmHg/min 0.2mmHg/min
250MEDICALDEVICES-MONITORINGUNIT
Respiration Rate Vital Sign SimulatorProsim 8
10 bpm
to 150 bpm5.9%
251MEDICALDEVICES-MONITORINGUNIT
Temperature Vital Sign SimulatorProsim 8 30 °C to 42 °C 0.4°C
252MEDICALDEVICES-MONITORINGUNIT
Weighing Balance(Repeatability,Linearity,Eccentricity)
Standard weights
0 to 100g (LC:0.01mg); 100g o 200 g(LC:0.1 mg); 200g to1000g (LC:1mg); 1Kg to 5 Kg(LC:0.01g); 5 Kg to10 Kg (LC:0.1g); 10Kg to 30 Kg(LC:0.1g); 30 Kg to300 Kg (LC:20g)
0.02 mg; 0.07 mg;0.82 mg; 0.0087 g;0.09 g; 0.14 g; 19.05g
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 132 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
253
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Chasis Leakage Electrical SafetyAnalyzer ESA 615 1 µA to 10 mA 5%
254
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
CurrentDefibrillatorAnalyzer Impulse7000 DP
1 mA to 200 mA 1.2%
255
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Discharge TimeDefibrillatorAnalyzer Impulse7000 DP
0.1 sec to 100.0 sec 0.08sec
256
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Ground WireResistance
Electrical SafetyAnalyzer ESA 615
0.2 Ohm to 2000Ohm 2.6%
257
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Heart RateDefibrillatorAnalyzer Impulse7000 DP
10 bpm to 300 bpm 1.2%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 133 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
258
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Isolation Test(Optional 500V)
Electrical SafetyAnalyzer ESA 615
0.5 MOhm to 100MOhm 2%
259
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Output EnergyDefibrillatorAnalyzer Impulse7000 DP
2 joules to 270 joules 0.6 % to 3.2 %
260
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Output Power ElectrosurgicalAnalyzer QA ES II 0 Watt to 300 watt 5.8%
261
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Oxygen Percentage Gas Flow AnalyzerVT Plus HF 0 % to 100 % 2.4%
262
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Pacer OutputDefibrillatorAnalyzer Impulse7000 DP
10 mA to 100 mA 0.12 % to 1.16 %
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 134 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
263
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Pacer RateDefibrillatorAnalyzer Impulse7000 DP
5 ppm to 300 ppm 1.2%
264
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Patient LeadLeakage Current(Mains on Patientapplied partIsolation Test)
Electrical SafetyAnalyzer ESA 615 10 µA to 10 mA 5%
265
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Patient Leakage Electrical SafetyAnalyzer ESA 615 10 µA to 10 mA 5%
266
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
PressureVital sign simulator& Pressure guage bydirect method
10 mmHg to 500mmHg 4%
267
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
pressure (PEEP) Gas Flow AnalyzerVT Plus HF
0 cmH2O to 30cmH2O 1.2cmH2O
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 135 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
268
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Pulse RateDefibrillatorAnalyzer Impulse7000 DP
30 ppm to 300 ppm 0.17 % to 1.16 %
269
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Pulse WidthDefibrillatorAnalyzer Impulse7000 DP
5 msec to 100.0msec 0.029%
270
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Respiration Rate Gas Flow AnalyzerVT Plus HF 4 bpm to 100 bpm 0.6bpm
271
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Time Interval stop watch directmethod 1 min to 60 min 0.64min
272
MEDICALDEVICES-PATIENTCONDITIONING/MAINTENANCE
Volume Accuracy Gas Flow AnalyzerVT Plus HF 0 LPM to 60 LPM 3.55%
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 136 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
273THERMAL-SPECIFIC HEAT& HUMIDITY
Humidity Chamberat 25°C
Using Humidity andTemp. Data Loggerby mapping method(minimum ninepoints).
25 %RH to 95 %RH 2.53%RH
274 THERMAL-TEMPERATURE
Glass TypeThermometers
Using Standard PRTwith MiliK Indicator,Low TemperatureBath (-30°C to140°C) & Oil Bath(-30°C to 140°C) bycomparison method
-25 °C to 50 °C 0.12°C
275 THERMAL-TEMPERATURE
Glass TypeThermometers
Using Standard PRTwith MiliK Indicator,Low TemperatureBath & Oil Bath(Amb. to 250°C) bycomparison method.
50 °C to 250 °C 0.16°C
276 THERMAL-TEMPERATURE
Indicator of BlackBody - Source orFurnace
Using Non-ContactPyrometer bycomparison method
50 °C to 500 °C 2.73°C
277 THERMAL-TEMPERATURE
Indicator of BlackBody Source /Furnace
Using Non-ContactPyrometer bycomparison method
500 °C to 1200 °C 3.36°C
278 THERMAL-TEMPERATURE
Indicator of Dry WellBlocks, MuffleFurnace
Using Standard SType TC with MiliKIndicator & Dry WellBath
650 °C to 900 °C 1.98°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 137 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
279 THERMAL-TEMPERATURE
Indicator of Dry WellBlocks, MuffleFurnace
Using Standard SType TC with MiliKIndicator bycomparison method
900 °C to 1200 °C 2.6°C
280 THERMAL-TEMPERATURE
Indicator ofIncubators(non-medicalpurpose),Ovens,Furnace, Dry WellBlocks, Liquid Bath.
Using Standard PRTwith MiliK Indicatorby comparisonmethod
50 °C to 250 °C 0.10°C
281 THERMAL-TEMPERATURE
Indicator of Ovens,Furnace, Dry WellBlocks.
Using Standard PRTwith MiliK Indicatorby comparisonmethod .
250 °C to 650 °C 0.40°C
282 THERMAL-TEMPERATURE
Indicator ofRefrigerators,Incubators(non-medical purpose),Ovens, Furnace, DryWell Blocks, LiquidBath
Using Standard PRTwith MiliK Indicatorby comparisonmethod
-35 °C to 50 °C 0.10°C
283 THERMAL-TEMPERATURE
Infrared / Non-ContactThermometers
Using Non-ContactPyrometer & BlackBody Furnace (e=0.95) (Amb to 500°Cby ComparisonMethod
50 °C to 500 °C 2.6°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 138 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
284 THERMAL-TEMPERATURE
Infrared / Non-ContactThermometers
Using Non-ContactPyrometer withBlack Body Furnace(e= 0.95) (300°C to1200°C) byComparison Method
500 °C to 1200 °C 3.72°C
285 THERMAL-TEMPERATURE Ovens, Furnace
Using Standard RTD& Standard N TypeTC with MultiChannel DataLogger by MappingMethod ( multipoints)
300 °C to 1200 °C 3.2°C
286 THERMAL-TEMPERATURE
Refrigerators,Incubators(non-medical purpose),Ovens, Furnace
Using Standard RTD& Standard N TypeTC with MultiChannel DataLogger by (minimum 9 location)by Mapping Method
-80 °C to 300 °C 1.17°C
287 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using Standard PRTwith MiliK Indicator,Low TemperatureBath , Oil Bath & DryWell Bath (Amb to650°C) bycomparison method
250 °C to 650 °C 0.40°C
Laboratory Name :GODREJ & BOYCE MFG. CO. LTD., LAWKIM MOTORS GROUP, CALIBRATION &INSPECTION, PLANT18B 1ST FLOOR, PIROJSHANAGAR, VIKHROLI(E), MUMBAI,MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017Certificate Number CC-2634 Page No 139 of 139Validity 28/03/2020 to 27/03/2022 Last Amended on 04/05/2020
This is annexure to 'Certificate of Accreditation' and does not require any signature.
S.No Discipline / Group
Measurand or ReferenceMaterial/Type of instrumentor material to be calibrated
or measured / QuantityMeasured /Instrum
Calibration or MeasurementMethod or procedure
Measurement range andadditional parameters
where applicable(Rangeand Frequency)
* Calibration andMeasurement
Capability(CMC)(±)
288 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using Standard PRTwith MiliK Indicator,Low TemperatureBath, Oil Bath & DryWell Bath (Amb to250°C)
50 °C to 250 °C 0.10°C
289 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using Standard SType TC with MiliKIndicator & Dry WellBath (150°C to1200°C) bycomparison method
650 °C to 900 °C 1.98°C
290 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges
Using Standard SType TC with MiliKIndicator & Dry WellBath (150°C to1200°C) bycomparison method
900 °C to 1200 °C 2.6°C
291 THERMAL-TEMPERATURE
RTD / ThermocoupleTemperature Sensorwith and withoutIndicators,TemperatureGauges,temperature ofthermohygrometer.
Using Standard PRTwith MiliK Indicator,Low TemperatureBath, ThermalChamber, Oil Bath &Dry Well Bath h (-30°C to 140°C) bycomparison method
-25 °C to 50 °C 0.10°C
* CMCs represent expanded uncertainties expressed at approximately the 95% level of confidence, using a coverage factor of k = 2.