51S

The contents of ALL the scope and calculation charts have to be considered indicative. It is the responsibility of the designer and / or of the user to proceed with the individual structural calculations and determine the specific planning applications of the package of couverture. In the multiplicity of the product that are present in the various documentation on the web, Alubel SpA cannot guarantee that the data and the exposed information’s are the most updated. It is the customer’s responsibility to contact our staff in order to obtain the latest version available.Alubel SpA reserves the right to update and modify the contents of this catalog at any time without prior notice. The information’s and the data contained in the technical data sheets, in the product specifications, in the product de-scriptions, in the brochures and in the advertising material have an indicative nature and become the binding content of the contract only after express written consent from us.

446

IsoCoppo Piano

19764

51

S

197 197

985

1039

197 197

A = external support

B = internal support

Polyurethane foam

Lateral seal

Drainage channel(drainage channel not available for versions in bituminous felt, fiberglass or aluminium foil)

FeaturesProfile height 51 mm

Panel width / Effective width 1039 mm / 985 mm

Minimum length / Maximum length 2100 mm / 13650 mm (multiple of 350 mm)

Initial / central / final part 175 mm / 350 mm / 175 mm

Minimum slope 15 %

Workings overlapping (lunghezza minima pannello 4200 mm)

Recommended use roofing

Type of insulation PUR

Standard insulation thickness (S) 40 mm

Average insulation thickness 65 mm

Other thicknesses (S) 30 - 50 - 60 - 80 mm

External support prepainted steel, prepainted aluminium, copper

Internal support prepainted steel, bituminous felt, fiberglass, aluminium foil

External finishing coppo red, antiqued coppo red, sand, antiqued sand

Internal finishing grey white,“Pirineo” white, walnut wood (painted), cherry wood (painted)

Fire class BRoof (T2) according to UNI EN 13501-5:2009, with reference to the harmonized standard UNI EN 14509:2013

447

IsoCoppo Piano

100 %

15 %

VersionsA) Prepainted galvanized steel / B) Prepainted galvanized steel

A) Pre-painted galvanized steel / B) Bituminous felt or aluminium foil

A) Prepainted aluminium / B) Prepainted galvanized steel

A) Prepainted aluminium / B) Bituminous felt or aluminium foil

A) Copper / B) Prepainted galvanized steel

Range of applicationIsoCoppo Piano can be used on roofs with a minimum slant of up to 15%

Indicative weight [kg/m2] Sheet thickness

external - internal [mm]Panel thickness [mm] without the corrugation

30 40 50 60 80

Steel 0,5 - Steel 0,4 10,5 10,9 11,3 11,7 12,5

Steel 0,5 - Bituminous felt 7,6 8,0 8,4 8,8 9,6

Aluminium 0,7 - Steel 0,4 7,9 8,3 8,7 9,1 9,9

Aluminium 0,7 - Bituminous felt 5,0 5,4 5,8 6,2 7,0

Copper 0,5 - Steel 0,4 11,1 11,5 11,9 12,3 13,1

Copper 0,6 - Bituminous felt 9,3 9,7 10,1 10,5 11,3

Thermal characteristicsPanel thickness

[mm]Average thickness

[mm]Heat transmission rate

U (W/m2K)30 55 0,396

40 65 0,341

50 75 0,300

60 85 0,253

80 105 0,214

448

IsoCoppo Piano

Panel thickness [mm] without the corrugation

Span [m] 30 40 50 60 80

1,5 282 334 347 368 402

2,0 175 195 208 220 255

2,5 83 101 113 126 151

3,0 41 60 74 82 94

Permitted load capacities [kg/m2]A upper side in steel 0,5 mm thickB inner side in steel 0,4 mm thick

Load uniformly distributed expressed in kg/m2 for a double span and downwards load. Assessments carried out applying a 1,5 safety factor to the load corresponding to the strain, equal to 1/200 of the gap.

Permitted load capacities [kg/m2]IsoCoppo Piano panel 40 mm thick consisting ofA upper side in aluminium 0,7 mm thickB inner side in steel 0,4 mm thick

Span [m] Permitted load capacity [daN/m2]

1,5 180

2,0 167

2,5 93

Security coefficient of the loads 1.5. Deflection limit l/200. Panels with three supports. Uniformly distributed load.

The contents of this calculation table are to be considered approximate and purely indicative. The structural calcu-lation is the task of the designer and/or user in each single case that also has to determine the application design specifications for the roofing in question.

449

IsoCoppo Piano

12

34

56

78

Laying the sheets

It is essential to maintain a 90° angle with the edge of the gutter. If the pitch is offset it is absolutely essential to keep the line parallel to the gutter. Any offset tolerances have to be kept on the side.

Wrong installation: this (not good!) draw-ing shows sheets laid on an offset roof and where parallelism has been maintained on the side instead of the gutter angle.

Right installation:laying at a 90° angle from the gutter line.

YESNO

450

IsoCoppo PianoFixing requirements

Band Fstrong Strong fixing

Band Fmed Average fixing

Band Fmin Minimum fixing

Ridge cap line

Eaves line

span

The support base of Alubel products on the purlins must not be lower than 40 mm for the metal supports and 50 mm for the wooden supports. For what concerns the wheelbase of the supports, follow the scope charts related to each Alubel’s products. Regarding the walkability, we recommend to not exceed the wheelbase of 1 m of support. Before starting the assembly operations of the product it is advisable to lay a wire parallel to the gutter line or converse, in order to obtain a perfect square of the covering. The number of fixing points is defined by various factors such as, for example: • sheet length• the climatic zone• mechanical features of fixing system• the position of the sheet on the covering (area)• the slopeAs shown in the table below, areas are identified on the roof according to the level of risk due to wind action.

451

IsoCoppo PianoFixing requirements

The designer must previously effectuate the verification of the number of fasteners. Ap-proximately, we briefly illustrate a fixing scheme normally used on Alubel roofing systems. We remind you that the number of fixings changes in relation to the span of the substruc-ture support. It is advisable to check that even the purlins, in particular those relating to the Fstrong and Fmed bands, are more anchored to the structure. In the case of structures without floor slabs and not walled in areas particularly subject to strong winds, it is nec-essary to increase the number of fixings, also included in the Fmin band.However, Alubel declines all responsibility for incorrect installation of its products. It is the responsibility of the designer and / or user to proceed with the individual use cases and to determine the specific planning applications of the package of couverture.

span ≤ 1,4 m

span ≤ 1,4 m

span ≤ 1,4 m

span≥ 1,4 m

span≥ 1,4 m

span≥ 1,4 m

Min

imum

fixi

ng

Aver

age

fixin

gSt

rong

fixi

ng

452

IsoCoppo PianoCorrect fixing of sheets and overlap

Lateral overlapping

The Alublok Fixing systemWith its special EPDM seal, the Alublok Fixing system ensures excellent results, especially when dealing with thermal expansion issues with the sheets.

453

IsoCoppo Piano

Indicative quantity for one pallet

Panel thickness[mm]

N°panels

Pallet height * [cm]

30 10 81

40 10 91

50 8 83

60 7 80

80 6 80

Packaging

* polystyrene spacer included** for feasibility, types and costs refer to our technical / commercial office

The images are purely for information.

Example of special package (on request)**Example of standard package

454

IsoCoppo PianoConstruction detailsCanale di gronda appeso su copertura lignea

Legenda01. Tirante 06. Barriera / Freno al vapore02. Reggi gronda 07. Isolante03. Listello in legno 08. Pannello IsoCoppo Piano04. Struttura in legno05. Assito / Perlinato

455

IsoCoppo PianoConstruction detailsCopertina di colmo

Legenda01. Struttura esistente in C.A.02. Isolante03. Listello in legno04. Pannello IsoCoppo Piano05. Raccordo con chiusura posteriore

456

IsoCoppo PianoConstruction detailsColmo a cerniera su copertura lignea

Legenda01. Struttura in legno 06. Colmo a cerniera02. Isolante 07. Pannello IsoCoppo Piano03. Assito / Perlinato04. Barriera / Freno al vapore05. Listello in legno

457

IsoCoppo PianoConstruction detailsRaccordo a muro

Legenda01. Listello in legno 06. Pannello IsoCoppo Piano02. Struttura in legno 07. Raccordo a muro03. Assito / perlinato04. Barriera al vapore05. Isolante

458

IsoCoppo PianoConstruction detailsColmo a cerniera su copertura in acciaio

Legenda01. Struttura in ferro02. Pannello IsoCoppo Piano03. Omega in lamiera zincata04. Colmo a cerniera05. Giunzione di sottocolmo

459

IsoCoppo PianoConstruction detailsCopertina laterale di raccordo alla copertura

Legenda01. Struttura esistente in C.A.02. Lattoneria di chiusura03. Pannello IsoCoppo Piano04. Isolante

460

IsoCoppo PianoConstruction detailsGiunto di dilatazione

Legenda01. Pannello IsoCoppo Piano02. Struttura esistente in C.A.03. Isolante04. Giunto di dilatazione05. Listello in legno

461

IsoCoppo PianoConstruction detailsRaccordo laterale falda parete con lattoneria

Legenda01. Struttura esistente in C.A.02. Copertina coprimuro03. Raccordo falda parete04. Pannello IsoCoppo Piano05. Isolante

462

IsoCoppo PianoConstruction detailsRaccordo laterale falda parete con tamponamento interno

Legenda01. Struttura esistente in C.A. 06. Isolante02. Copertina coprimuro03. Lastra Alubel 15 / Alubel 2104. Raccordo falda parete05. Pannello IsoCoppo Piano

463

IsoCoppo PianoConstruction detailsCopertina laterale di raccordo su copertura metallica

Legenda01. Copertina laterale02. Struttura in acciaio03. Pannello IsoCoppo Piano04. Omega in lamiera zincata

464

IsoCoppo PianoConstruction detailsCanale di gronda appeso su copertura metallica

Legenda01. Tirante02. Canale di gronda03. Omega in lamiera zincata 04. Struttura in acciaio05. Pannello IsoCoppo Piano

465

IsoCoppo PianoConstruction detailsCanale di gronda su copertura metallica

Legenda01. Struttura in acciaio 06. Pannello IsoCoppo Piano02. Copertina coprimuro 07. Struttura in acciaio03. Lastra Alubel 15 / Alubel 21 08. Omega in lamiera zincata04. Raccordo a muro05. Canale di gronda e pluviale

466

IsoCoppo Piano

22/0

9/21

Construction detailsConversa

Legenda01. Pannello IsoCoppo Tek 06. Omega in lamiera zincata02. Struttura in acciaio03. Conversa04. Pluviale05. Isolante