Invision G9 Installation Instructions
Transcript of Invision G9 Installation Instructions
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA) Document # GRA Created: 7/5/2006 Part Number: - Accessory Code:
Kit Contents
Item # Qty Component Description1 1 MONITOR ASSEMBLY2 1 TRIM RING3 1 BRACKET ASSEMBLY4 1 HARDWARE BAG5 1 PAPER CUTOUT TEMPLETE6 1 INSTALLATION INSTRUCTIONS7 1 ANTENNA ASSEMBLY8 1 WIRE PULLER
Hardware Bag Contents
Item # Qty Component Description1 5 Red T-Taps2 1 Blue Male Spade3 4 1/4" X 20 Nuts4 1 1/2" Phillips Screw5 4 Barrel Nuts6 8 1/4" Phillips Screws7 4 1/4" X 1" Washers8 3 6" Wire Ties9 2 11" Wire Ties10 1 4" x 8" Foam Tape11 4 Monitor Bracket T-Studs12 1 Alcohol Pad
Additional Items Required For Installation
Item # Qty DescriptionElectrical Tape
Recommended Tools
Seat/Floor Covers Blankets
Pliers 4mm Allen DriverNylon Removal Tool 10mm Socket#2 Phillips Screwdriver Wire Crimper#1 Phillips Screwdriver Marker7/16" Socket Utility Knife14mm Socket Wire Cutters3/32" Drill Bit/Stop
Safety Tools
Installation Tools
Special Tools
Special Chemicals
Color Applicability/Trim Level
Vehicle Trim Color
Gray
Beige
XX
Accessory C
olor
AshIvory
General Applicability All Highlander Moonroof Vehicles Conflicts None Recommended Sequence of Application
Item # Accessory1 Install Wiring2 Install Modulator3 Install Monitor
*Mandatory Legend
Page 1 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
SPECIAL NOTE:
Installation Sequences After Safety mandated preparatory steps have been
taken, the installation sequence is the suggested
method for completing the accessory installation. In
some instances the suggested sequence is written for
one associate to install and in others the sequence is
given as part of a team accessory installation. Unless
otherwise stated in the document, the associates may
perform the installation steps in any order to make the
installation as efficient as possible while maintaining
consistent quality.
A. Pre-installation Precaution 1. Use Seat and Floor Protectors to avoid damage
to surfaces.
2. If the vehicle is equipped with an Anti-theft
radio, the radio code must be written down prior
to disconnecting the battery cable. The code
must be re-entered when the negative battery
cable is reconnected. Disconnecting the
battery may cause certain vehicle settings to be
lost. Manufacturer’s recommendations for
battery removal should be followed.
Disconnecting the battery is recommended.
Page 2 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
B. Battery Disconnect
1. NOTE: be sure to open the rear hatch, PRIOR
to disconnecting the battery.
2. Remove the NEGATIVE (-) battery terminal
using a 10mm socket before starting any
disassembly. (Fig. B2)
C. Mark Monitor Cutout
1. Align template with rear edge of moonroof
opening on headliner. (Fig. C1)
2. Carefully mark monitor cutout with marker.
(Fig C2)
D. Cutout Monitor Opening
1. Be sure sunshade is closed before step D2 to
prevent damage.
2. Carefully cut out monitor opening using a sharp
utility knife. (Fig. D2)
Fig. B2 Fig. C1 Fig. C2 Fig. D2
Page 3 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
E. Remove Center Finish Panel
1. Carefully pry center finish panel from dash using
fingers or NRT if needed. (Fig. E1)
F. Remove Radio/HVAC Controls
1. Remove (6) bolts using a 10mm socket. (Fig. F1)
2. Remove (6) connectors from rear of radio/HVAC
control assembly. (Fig. F2)
3. Remove antenna connector from rear of radio.
(Fig. F3)
G. Lower Glove Box
1. Remove dampner attachment screw under dash
using a #1 phillips head screwdriver. (Fig. G1)
2. Remove dampner attachment by pulling it from
the bracket.
Fig. E1 Fig. F1 Fig. F2 Fig. F3 Fig. G1
Page 4 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
3. Squeeze upper sides of glove box compartment
with hands to lower. (Fig. G3)
H. Remove Passenger Side Visor
1. Carefully remove visor screw cover by prying
with NRT. (Fig. H1)
2. Remove (2) phillips head screws using #2
phillips head screwdriver. (Fig. H2)
I. Remove Grab Handle
1. Carefully open passenger side grab handle
screw covers by hand. (Fig. I1)
2. Remove (2) bolts using a 10mm socket. (Fig. I2)
Fig. G3 Fig. H1 Fig. H2 Fig. I1 Fig. I2
Page 5 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
J. Remove Door Seal Trim
1. Carefully pull door seal trim from upper half of
passenger door opening. (Fig. J1)
K. Remove A-pillar Garnish Molding
1. Pry A-pillar molding on passenger side,
beginning at top (underside), using a NRT.
(Fig. K1)
2. Remove molding from vehicle.
L. Remove B-pillar Molding
1. Remove passenger seatbelt cover by prying with
a NRT. (Fig. L1)
2. Remove seatbelt bolt with a 14mm socket.
(Fig. L2)
3. Pull B-pillar molding back from top (by hand) far
enough to allow headliner to drop slightly.
(Fig. L3)
Fig. J1 Fig. K1 Fig. L1 Fig. L2 Fig. L3
Page 6 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
M. Route Wiring from Monitor Opening to A-pillar
1. Feed wire puller above headliner, starting from
A-pillar. (Fig. M1)
2. Feed wire puller until it’s exposed in monitor
cutout. (Fig. M2)
3. Attach main harness and antenna harness to
wire puller at end near A-pillar. (Fig. M3)
4. Be sure to attach end of main harness with
snaps on sides to wire puller. Use electrical tape
to secure antenna coax to cable to avoid
damage to cable end.
5. Carefully pull harnesses from monitor cutout until
approximately 12” is exposed through monitor
opening. (Fig. M5)
6. Remove tape and wire puller.
Fig. M1 Fig. M2 Fig. M3 Fig. M5
Page 7 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
N. Install Monitor Bracket
1. Insert (2) T-studs in forward crossmember.
(Fig. N1)
2. Install bracket, aligning it with the forward (2) T-
studs. (Fig. N2)
3. Install (2) washers and ¼”-20 nuts onto forward
T-studs and leave loose.
4. Install (2) T-studs into the rear crossmember.
(Fig. N4)
5. Install (2) washers and ¼”-20 nuts onto the rear
T-studs.
6. Tighten (4) ¼”-20 nuts with 7/16” socket.
(Fig. N6)
Fig. N1 Fig. N2 Fig. N4 Fig. N6
Page 8 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
O. Install Monitor Wiring
1. Drill pilot hole with 3/32” drill bit (with stop ¼”
from end of bit) in vehicle crossmember as
shown. (Fig. O1)
2. Attach eyelet on main harness to crossmember
with ½” phillips head screw. (Fig. O2)
3. Install (1) T-tap to the red wire and (2) T-taps on
the black wire of the main harness. (Fig. O3)
4. Attach each of the blue spade clips from the 12”
domelamp harness to each of the T-taps in the
following sequence:
Domelamp Harness Main Harness
Black/Red Stripe Wire Red Wire
Red/Black Stripe Wire Black Wire
Purple/Brown Stripe Wire Black Wire
P. Install Monitor Trim Ring
1. Cut hole in fabric of trim ring approximately 1”
smaller than inner hole in trim ring. (Fig. P1)
2. Attach trim ring to monitor with (8) ¼” phillips
head screws using #1 phillips screwdriver.
(Fig. P2)
Fig. O1 Fig. O2 Fig. O3 Fig. P1 Fig. P2
Page 9 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
Q. Install Monitor
1. Open monitor screen.
2. Connect white connectors together and then
connect black connectors together. (Fig. Q2)
3. Attach power cable and antenna connectors to
monitor (hand tighten antenna lead).
4. Tuck wires above headliner. (Fig. Q4)
5. Locate monitor onto (4) studs attached to
monitor bracket.
6. Install (4) barrel nuts and tighten with 4mm hex
(Allen) driver. (Fig. Q6)
R. Install TV Antenna to Windshield
1. Clean windshield with alcohol pad.
2. Peel red adhesive backing from antenna base
and partially peel back paper backing. (Fig. R2)
3. Attach antenna base to center of windshield near
top, inserting harness above headliner (locate
base off center if equipped with EC mirror).
(Fig. R3)
Fig Q2 Fig. Q4 Fig. Q6 Fig.R2 Fig. R3
Page 10 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
4. Tuck harness above headliner, working from
center towards A-pillar on passenger side.
(Fig. R4)
5. Peel remaining paper backing and attach to
windshield from center towards A-pillars.
(Fig. R5)
6. Cut any excess antenna at A-pillars, if
necessary.
S. Route Wire Harness to Radio
1. Feed wire puller between A-pillar and I/P, pull
through glove box opening. (Fig. S1)
2. Attach main harness to wire puller at A-pillar.
3. Pull harness through glove box opening.
(Fig. S3)
4. Pull main harness through radio opening using
wire puller. (Fig. S4)
5. Remove wire puller.
Fig. R4 Fig. R5 Fig. S1 Fig. S3 Fig. S4
Page 11 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
T. Connect Wiring at Radio
1. Attach red T-tap to gray wire (PIN #3 on
connector R3 for 6 speaker audio circuit, PIN
#11 on connector R4 for 8 speaker audio circuit)
using pliers. (Fig. T1)
2. Attach red wire from main harness (with blue
spade clip) to red T-tap on gray wire. (Fig. T2)
3. Connect male antenna lead (vehicle) to female
antenna lead (FM Modulator). (Fig. T3)
4. Connect main harness connector to FM
Modulator harness. (Fig. T4)
5. Wrap FM Modulator with foam tape.
6. Attach FM Modulator to I/P bracket using (2) 11”
wire ties. (Fig. T6)
7. Trim excess material from wire ties.
Fig. T1 Fig. T2 Fig. T3 Fig. T4 Fig T6
Page 12 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
U. Fix A-pillar Wiring
1. Fix main harness to black factory wiring along A-
pillar with (3) 6” wire ties. (Fig. U1)
2. Trim excess material from wire ties.
V. Reassemble Components
1. Reassemble trim, radio, glove box, visor, handle,
and door seal by reversing steps E-L.
2. Reconnect vehicle battery by reversing step B.
Torque terminal connectors to 36 in-lbs.
W. Complete Installation
1. Install 2 AAA batteries in remote control.
2. Install 2 AAA batteries in each headphone
headset.
3. After testing system, store owners manual in
glove box. Store remote and headphones in
rear of center console.
Fig. U1
Page 13 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
Wiring Diagram
Page 14 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
Functional Verification:
Check
Accessory Function checks:
Look For:
Turn vehicle ignition to ON, depress power button on remote control for monitor.
Monitor should power on, start up screen should appear on screen.
Insert DVD into monitor, press enter.
DVD should begin playing.
Depress “sound around” on remote control. Tune vehicle FM radio station to channel displayed on screen.
“Sound around “ON” and FM channel displayed on screen.
Depress source button until “TV” is displayed scroll channel up/down until TV channel is observed.
TV tuner reception. (Reception may be poor in areas where signal may be blocked.)
Depress “sound around” on remote control. Tune vehicle FM radio station to channel displayed on screen.
“Sound around OFF” and FM channel displayed on screen. Vehicle radio should operate normal
Turn power “ON” wireless headphones (turn Volume dial up slightly on headphones).
Program on G9 monitor should be audible through wireless headphones.
Slide dome lamp switch on monitor to “ON”.
Both lights on monitor should turn on.
Page 15 of 16
TOYOTA 2005/6 HIGHLANDER MOONROOF 9” OVERHEAD VIDEO (AUTOCINEMA)
Troubleshooting: Condition:
Check For:
Unit does not power "ON"
1. Is ignition turned "ON”? 2. Are batteries installed in remote control? 3. Are power connections and ground secured? 4. Check power on the vehicle side of power
connection. 5. Check power on the accessory side of power
connection. 6. Is vehicle fuse blown? If yes, check to see that
there is not a short circuit. 7. Check overhead video unit for continuity to ground
on black wire and power at red wire on 4 pin connector (Fig. 1). Use eyelet as ground connection for all voltage checks. If continuity and power exist, the problem lies in the overhead unit.
Sound is not heard through vehicle radio 1. Is “sound around” turned on?
2. Does vehicle radio station match radio station displayed when “sound around” is turned “ON”?
3. Check that FM Modulator is receiving power. Test G9 main harness for continuity at 8 pin connector on each side. All pins should be continuous (Fig. 1). Test for power at PIN #8, ground at PIN #1, and audio voltage of .02 V at PIN #3 and PIN #4. If voltages are not present, the problem lies in the overhead unit.
Sound is not heard through wireless headphones 1. Are batteries installed? 2. Is power "ON" (headphones)? 3. Is volume turned "UP" (on headphones)? 4. Is anything blocking signal between monitor and
headphones?
Vehicle has poor sound 1. Turn off “sound around” on monitor
Interference caused by local radio station 1. Use FM Model Select to choose a different channel.
IR Sensor inoperative 1. Verify that the batteries in the remote are fresh. 2. Verify that the remote sensor eye is not
obstructed. 3. Verify that the infrared transmitter is affixed over
the sensor eye of the component to be controlled. No picture 1. Verify the correct video input mode is used on TV.
2. Verify the video cable is plugged into jack securely.
Unit powers up but no audio and/or video 1. Try another disc format (Note: not all DVD formats are compatible with player
Television picture poor or no reception 1. Verify TV station is local. 2. Check antenna input connection.
If problem persists contact INViSiON Technical Assistance at 1-866-869-7888
Page 16 of 16