INVINSA and INVINSA FR - Johns Manville · Apply adhesive to the ENRGY 3 layer and set Invinsa or...
12
INVINSA ® and INVINSA ® FR Application Instructions and Code Approvals
Transcript of INVINSA and INVINSA FR - Johns Manville · Apply adhesive to the ENRGY 3 layer and set Invinsa or...
INVINSA®
and INVINSA®
FRApplication Instructions and Code Approvals
JM-Approved Fasteners
ENRGY 3® PolyisocyanurateRoof Insulation
JM PVC with DuPont™
Elvaloy® KEE, JM TPO or JM EPDM, Fully Adhered
Invinsa® or Invinsa® FR Roof Board,Mechanically Fastened
Deck
JM-Approved Fasteners
ENRGY 3® PolyisocyanurateRoof Insulation
JM-ApprovedFasteners
JM PVC with DuPont™
Elvaloy® KEE or JM TPOMechanically Fastened
Invinsa® or Invinsa® FR Roof Board,Mechanically Fastened
Deck
ENRGY 3® PolyisocyanurateRoof Insulation
Invinsa® Roof Board,Fully Adhered
DynaGrip Base SD/SA Base SheetDynaWeld Cap FR Cap Sheet
Deck
DeckExistingSingle Ply Roof
ExistingModified Bitumen Roof
Existing Built-Up Roof
Invinsa® Roof Board
ENRGY 3® PolyisocyanurateRoof Insulation
JM-Approved FastenersJM PVC with DuPont™
Elvaloy® KEE, JM TPO or JM EPDMRoofing Membrane
Single Ply Fully Adhered Systems
Single Ply Mechanically Fastened Systems
SBS Hybrid Systems
Various Roof Systems
New Construction and Re-Roof
New Construction and Re-Roof
New Construction and Re-Roof
Re-CoverJM-Approved Fasteners
Cold Application Adhesive
Deck
ENRGY 3®
PolyisocyanurateRoof Insulation
Invinsa® Roof Board JM Two-Part UrethaneInsulation Adhesive, JM Roofing System Urethane Adhesive, JM One-StepFoamable Adhesive
DynaGlas® FR CRCap Sheet
DynaBase® Base Sheet
SBS Cold Adhesive Applied
New Construction and Re-Roof
A Valuable Component to Your Roof SystemThe addition of Invinsa® or Invinsa® FR Roof Board to a single ply or SBS roof system increases the roof’s resistance to damage from various sources, including but not limited to hail, foot traffic, construction loads and normal roof maintenance. Invinsa is engineered as an integral part of the roof system, providing a protective layer for the insulation below and working with the membrane above to improve performance. Invinsa may be specified for new, re-roof and re-cover applications.
Product Advantages• High resistance to indentation, compression and crushing during
installation of the roof system and during periodic maintenance, once the roof is completed
• Rigidity to support the roof membrane
• Increased resistance to moisture absorption
• Dimensional stability
• Compatibility with PVC, TPO, EPDM and SBS roofing systems
• UL®, FM Global® and other important building agency approvals
JM TPO manufacturing facility in Scottsboro, AL
1
Patterns for Mechanical Fastening
6"6"
12"
6"
12" 12"
24"
5 Fasteners/Board
5 Fasteners/Board
8 Fasteners/Board
12 Fasteners/Board 16 Fasteners/Board(1 per 2 ft2)
8 Fasteners/Board
36"
12" 12"3 Spaces @ 24"
12" 12"3 Spaces @ 24"
24"
24"
6"12"
6"
6"
6"
6"
18"
18"
6"
24"
6"
24"
Adhesive Patterns for Fully Adhering Invinsa Roof BoardTo adhere to ENRGY 3® using JM Roofing System Urethane Adhesive (RSUA), JM One-Step Foamable Adhesive, JM Two-Part Urethane Insulation Adhesive, JM Green Two-Part Urethane Insulation Adhesive and other adhesives.
1. Apply adhesive to the ENRGY 3 layer and set Invinsa or Invinsa FR on top of adhesive pattern.
2. Follow instructions on respective adhesives with regard to application rates, open times, setting times and board weighting.
3. All ENRGY 3 boards run parallel to the 8' edge of a 4' x 8' Invinsa or Invinsa FR board with a 2' offset.
Note: For detailed information about perimeter and corner installation, please refer the fastening pattern UA-12 available on the JM Roofing website or in current JM Commercial/Industrial Roof Systems Manuals.
4' x 8' ENRGY 3 ® Roof Insulation Boards
(with 4' offset) 4' x 8' Invinsa ® or Invinsa ® FR Roof Boards
(with 2' offset to ENRGY 3)
2
Standard Adhesive PatternFor all adhered Invinsa systems.
12"
12"
4"
4"
Adhesive Pattern Under Two 4' x 8' Invinsa ® or Invinsa ® FR Roof Boards
Adhesive Ribbons Set on 12" CentersEdge Ribbons Set on 6" Centers
12"
3"
3"
3"
5"
Heavy-Duty Adhesive PatternFor systems in which membrane wrinkling is a concern, including high deck non-uniformity and self-adhering membranes.
12"6" 6"
6"
Adhesive Pattern Under 4' x 8' Invinsa ® or Invinsa ® FR Roof Board
Adhesive Ribbons Set on 12" Centers
6"4' x 8' ENRGY 3® Roof Insulation
Note: For detailed information about perimeter and corner installation, please refer the fastening pattern UA-12 available on the JM Roofing website or in current JM Commercial/Industrial Roof Systems Manuals.
3
4
FM Global® ApprovalsJM TPO Membrane Systems — Mechanically Fastened
Deck
Typ
e
Appl
icat
ion
Type
Deck
Gra
de1 (K
SI)
Roof
Nav
SM
Asse
mbl
y #1
Insu
latio
n2
Cove
r Boa
rd
Slop
e (#
”: 1
ft)
Mem
bran
e W
idth
(ft)
Mem
bran
e Pl
ate
Mem
bran
e Fa
sten
er
Mem
bran
e Fa
sten
er
Spac
ing
(#“
OC)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l
N
80, 33247419-0-0
E3
I FR 1.510'
HL HL
12"
60
1 A SH
341166-0-0 I 1
80222741-0-0 I FR 1.5
8'75
341114-0-0 I 1
80, 33222809-0-0 I FR 1.5
XHL XHL 90341117-0-0 I 1
80222820-0-0 I FR 1.5
10'341120-0-0 I 1
80, 33
222859-0-0 I FR 1.5
HL HL 6"
90341123-0-0 I 1222814-0-0 I FR 1.5
8' 120341118-0-0 I 1222952-0-0 I FR 1.5
5' 165341138-0-0 I 1
FM Global® ApprovalsJM TPO Membrane Systems — RhinoPlate Systems*
Deck
Typ
e
Appl
icat
ion
Type
Deck
Gra
de1 (K
SI)
Roof
Nav
SM
Asse
mbl
y #1
Insu
latio
n2
Cove
r Boa
rd
Slop
e (#
”: 1
ft)
Mem
bran
e W
idth
(ft)
Mem
bran
e Pl
ate
Mem
bran
e Fa
sten
er
Fast
ener
Spa
cing
(#
: ft2 )
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l
N33
247612-0-0
E3
I FR 1.5
10' RhP HL
1:5.33 90
1 A SH
341170-0-0 I 1247628-0-0 I FR 1.5
1:4 135341174-0-0 I 1
80, 33249582-0-0 I FR 1.5
6" OC 210341186-0-0 I 1
* The plates and fasteners are applied through the insulation boards and then bonded to the underside of the membrane.
FM Global® ApprovalsJM TPO — Fastened Cover Board, Fully Adhered Membrane
Deck
Type
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #1
Insu
latio
n2
Cove
r Boa
rd
Cove
r Boa
rd
Fast
ener
Cove
r Boa
rd
Fast
ener
Rat
e (#
: ft2 )
Mem
bran
e
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Spec
ial
Cons
ider
atio
ns
Stee
l
RC 317599-0-0
E3
I
UF 1:2
TSB 0.25
90 1 A SH *
N
327590-0-0
I, I FR
327593-0-0 LVOC 0.5361269-0-0 FB
WB 0.75361273-0-0
T
RC
327596-0-0 LVOC0.5
354045-0-0 XFB
WB361270-0-0E3 0.75
361274-0-0 T* Optional SR Thermal Barrier included in the assembly.
Notes1. Deck Grade and assemblies vary. Please check RoofNavSM for specific deck constructions of individual approvals.2. All E3 insulation for new roofs is 1.5" min unless otherwise listed. Re-Cover insulation thickness varies by approval. Please check individual listings.
This is intended to serve as a reference guide, please check RoofNav for the most current information and assembly details.FM Global and RoofNav are among the trademarks or registered trademarks of Factory Mutual Insurance Company and FM Approvals LLC, respectively.
Insulation/Cover BoardE3 = ENRGY 3® I = Invinsa® Roof Board I FR = Invinsa® FR Roof Board X = No Insulation
Application TypeN = New Roof RC = Re-Cover
Fastener and PlateHL = High Load RhP = RhinoPlate™
UF = UltraFast®
XHL = Extra High Load
MembraneFB = JM TPO Fleece Backed T = JM TPO
AdhesiveLVOC = JM Low VOC SB = JM Solvent Based WB = JM Water Based
5
FM Global® ApprovalsJM TPO — Fastened Insulation, Subsequent Layers Fully Adhered
Deck
Type
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #1
Insu
latio
n2
Insu
latio
n Fa
sten
er
Insu
latio
n Fa
sten
er R
ate
(#: f
t2 )
Cove
r Boa
rd
Cove
r Boa
rd
Adhe
sive
3
Cove
r Boa
rd
Adhe
sive
Rat
e (ri
bbon
s: #
” OC
)
Mem
bran
e
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l
N
234926-0-0
E3 UF1:4
I 2P UIA 12"T
SB 0.25
751 A SH
234930-0-0 LVOC 0.5361246-0-0
WB 0.75361252-0-0
FB339704-0-0 1:1 RSUA 0.5 135
FM Global® ApprovalsJM TPO — Fastened Thermal Barrier, Fully Adhered Insulation, Cover Board, and Membrane
Deck
Type
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #1
Ther
mal
Bar
rier
Ther
mal
Bar
rier
Fast
ener
Ther
mal
Bar
rier
Fast
ener
Rat
e (#
: ft2 )
Vapo
r Bar
rier
Insu
latio
n2
Insu
latio
n Ad
hesi
ve3
Insu
latio
n Ad
hesi
ve
Rate
(rib
bons
: #”
OC)
Cove
r Boa
rd
Cove
r Boa
rd
Adhe
sive
3
Cove
r Boa
rd
Adhe
sive
Rat
e (ri
bbon
s: #
” OC
)
Mem
bran
e
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l
N361275-0-0
SR(min 0.625")
UF 1:4 VB SA E3 2P UIA 12" I 2P UIA 12"T
WB 0.7590 1 A SH361278-0-0 FB
353883-0-0 T SB, WB 0.5
FM Global® ApprovalsJM TPO — Fully Adhered Insulation, Cover Board and Membrane
Deck
Typ
e
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #1
Vapo
r Bar
rier
Insu
latio
n2
Insu
latio
n Ad
hesi
ve3
Insu
latio
n Ad
hesi
ve R
ate
(ribb
ons:
#”
OC)
Cove
r Boa
rd
Cove
r boa
rd
Adhe
sive
3
Cove
r Boa
rd
Adhe
sive
Rat
e (ri
bbon
s: #
” OC
)
Mem
bran
e
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stru
ctur
al
Conc
rete
N
361264-0-0361263-0-0 DG
E32P UIA
12" I2P UIA
12"
TWB 0.75
210
NC A SHFB
360219536-0-0
XSB, WB 0.5
360361249-0-0 WB 0.75339727-0-0 2P UIA, RSUA 2P UIA, RSUA RSUA 0.5 135
Notes
1. Assemblies vary. Please check RoofNavSM for specific deck constructions of individual approvals.2. Some assemblies require a 2" weld. Check specific assemblies.3. All E3 insulation for new roofs is 1.5" min unless otherwise listed. Re-Cover insulation thickness varies by approval. Please check individual listings.4. Other adhesives may be available in the referenced approvals. Please check listing for all adhesive options.
This is intended to serve as a reference guide, please check RoofNav for the most current information and assembly details.FM Global, RoofNav and Securock are among the trademarks or registered trademarks of Factory Mutual Insurance Company, FM Approvals LLC and Georgia-Pacific LLC, respectively.
Insulation/Cover BoardE3 = ENRGY 3® I = Invinsa® Roof Board
Thermal/Vapor BarrierDG = DynaGrip Base SD/SA SR = Securock® Gypsum Fiber VB SA = JM Vapor Barrier SA X = No Vapor Barrier
Application TypeN = New Roof
Fastener and PlateUF = UltraFast®
MembraneFB = JM TPO Fleece Backed T = JM TPO
Insulation/Cover Board Adhesive2P UIA = JM Two-Part Urethane Insulation Adhesive
AdhesiveLVOC = JM Low VOC 2P UIA = JM Two-Part Urethane RSUA = JM Roofing System Urethane Adhesive SB = JM Solvent Based WB = JM Water Based
6
FM Global® ApprovalsJM PVC & JM PVC SD Plus — Mechanically Fastened Membrane
Deck
Typ
e
Appl
icat
ion
Type
Deck
Gra
de1 (K
SI)
Roof
Nav
SM
Asse
mbl
y #1
Insu
latio
n2
Cove
r Boa
rd
Slop
e (#
”: 1
ft)
Mem
bran
e
Mem
bran
e W
idth
(ft)
Mem
bran
e Pl
ate
Mem
bran
e Fa
sten
er
Mem
bran
e Fa
sten
er
Spac
ing
(#“
OC)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Spec
ial C
ondi
tions
Stee
l
N
80 210448-0-0
E3 I 1
JM PVC
6.5'HL HL
6"150
1
A
SH
*’ **
33359040-0-0
JM PVC, SD Plus 90B
172969-0-0A
80210446-0-0 JM PVC 12" 105
**366308-0-0 JM PVC, SD Plus 6" 9010' B* Assembly has an air barrier. All assemblies with air barrier have insulation fastening rate of 1 fastener per 2 square feet.** Laps sealed with 2" wide weld.
FM Global® ApprovalsJM PVC & JM PVC SD Plus — RhinoPlate Systems*
Deck
Type
Appl
icat
ion
Type
Deck
Gra
de1 (K
SI)
Roof
Nav
SM
Asse
mbl
y #1
Insu
latio
n2
Cove
r Boa
rd
Slop
e (#
”: 1
ft)
Mem
bran
e
Mem
bran
e W
idth
(ft)
Mem
bran
e Pl
ate
Mem
bran
e Fa
sten
er
Fast
ener
Spa
cing
(#
: ft2
)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l
N 33247656-0-0
E3 I 1 JM PVC,SD Plus 10' RhP HL
1:5.33 901 A SH
247668-0-0 1:4 135
* The plates and fasteners are applied through the insulation boards and then bonded to the underside of the membrane.
FM Global® ApprovalsJM PVC — Fastened Cover Board, Fully Adhered Membrane1
Deck
Typ
e
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #2
Insu
latio
n3
Cove
r Boa
rd
Cove
r boa
rd F
aste
ner
Cove
r Boa
rd
Fast
ener
Rat
e (#
: ft2 )
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l RC 354042-0-0 X I UF 1:2 SB, LVOC 1 90 1 A SHN 318004-0-0
E3RC 318014-0-0
Notes:1. Deck Grade and assemblies vary. Please check RoofNavSM for specific deck constructions of individual approvals.2. Insulation thickness requirements vary for re-cover construction. Check specific RoofNav numbers. All E3 insulation for new roofs is 1.5" min unless otherwise listed. Re-Cover insulation thickness varies by approval. Please check individual listings.3. Other adhesives may be available in the referenced approvals. Check application rate for all approvals listing hot asphalt (HA) as an adhesive. Please check listing for all adhesive options
This is intended to serve as a reference guide, please check RoofNav for the most current information and assembly details.FM Global and RoofNav are among the trademarks or registered trademarks of Factory Mutual Insurance Company and FM Approvals LLC, respectively.
Insulation/Cover BoardE3 = ENRGY 3® I = Invinsa® Roof Board X = No Insulation
Application TypeN = New Roof RC = Re-Cover
Fastener and PlateHL = High Load RhP = RhinoPlate™
UF = UltraFast®
AdhesiveLVOC = JM Low VOCSB = JM Solvent Based
7
Notes1. Deck Grade and assemblies vary. Please check RoofNavSM for specific deck constructions of individual approvals.2. All E3 insulation for new roofs is 1.5" min unless otherwise listed. Re-Cover insulation thickness varies by approval. Please check individual listings.
This is intended to serve as a reference guide, please check RoofNav for the most current information and assembly details.FM Global and RoofNav are among the trademarks or registered trademarks of Factory Mutual Insurance Company and FM Approvals LLC, respectively.
FM Global® ApprovalsJM PVC — Fastened Insulation with Subsequent Layers Fully Adhered1
Deck
Type
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #2
Insu
latio
n3
Insu
latio
n Fa
sten
er
Insu
latio
n Fa
sten
er R
ate
(#: f
t2 )
Cove
r Boa
rd
Cove
r boa
rd A
dhes
ive4
Cove
r Boa
rd A
dhes
ive
Rate
(rib
bons
: #”
OC)
Mem
bran
e Ad
hesi
ve
Slop
e (#
”:1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stee
l
N268259-0-0 E3 (min 2")
UF1:4
I 2P UIA 12" LVOC, SB 1 90 1 A SH268260-0-0 E3 1:2
FM Global® ApprovalsJM PVC — Fully Adhered Insulation, Cover Board and Membrane1
Deck
Typ
e
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #
Vapo
r Bar
rier
Insu
latio
n2
Insu
latio
n Ad
hesi
vee3
Insu
latio
n Ad
hesi
ve
Rate
(rib
bons
: #”
OC)
Cove
r Boa
rd
Cove
r Boa
rd
Adhe
sive
4
Cove
r Boa
rd A
dhes
ive
Rate
(rib
bons
: #”
OC)
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(C
lass
)
Exte
rnal
Fire
(C
lass
)
Hail
Ratin
g
Stru
ctur
al C
oncr
ete
N184081-0-0 2 ply GP or GPP
E3
MBR BA 1.5 gal/sq
I
MBR BA
12"
WB
1
225
NC A SH
227693-0-0
X
2P UIA
12"
2P UIAWB, LVOC
210RC 228669-0-0N 227694-0-0
UIA UIA 150RC 228671-0-0
N
232113-0-0
2P UIA
2P UIASB, WB,
LVOC 210279362-0-0
DG279382-0-0279375-0-0
WB, LVOC279379-0-0 UIA 150279393-0-0
APP2P UIA
SB, WB, LVOC 210279429-0-0
279418-0-0WB, LVOC
279419-0-0 UIA 150
FM Global® ApprovalsJM EPDM — Fastened Cover Board, Fully Adhered Membrane
Deck
Type
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #
Insu
latio
n
Cove
r Boa
rd
Cove
r Boa
rd
Fast
ener
Cove
r Boa
rd
Fast
ener
Rat
e (#
: ft2 )
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(Cla
ss)
Exte
rnal
Fire
(Cla
ss)
Hail
Ratin
g
Stee
l
N 339378-0-0 E3I
UF 1:2 LVOC, SB, WB 1
90
1 A SHRC
354081-0-0X
354034-0-060N 300835-0-0
E3 I, I FRRC 300840-0-0
Insulation/Cover BoardE3 = ENRGY 3® I = Invinsa® Roof Board I FR = Invinsa® FR X = No Insulation
Vapor BarrierAPP = JM APP Base DG = DynaGrip Base SD/SA GP = GlasPly® IV GPP = GlasPly® Premier X = No Vapor Barrier
Application TypeN = New Roof RC = Re-Cover
Fastener and PlateHL = High Load RhP = RhinoPlate™
UF = UltraFast®
XHL = Extra High Load
Insulation/Cover Board AdhesiveMBR BA = MBR® Bonding Adhesive 2P UIA = JM Two-Part Urethane Insulation Adhesive UIA = JM Urethane Insulation Adhesive
AdhesiveLVOC = JM Low VOC MBR BA = MBR® Bonding Adhesive 2P UIA = JM Two-Part Urethane SB = JM Solvent Based UIA = JM Urethane Insulation Adhesive WB = JM Water Based
FM Global® Approvals JM SBS Systems — Cold Adhesive Applied
Deck
Typ
e
FM R
atin
g
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #
Slop
e
ENRGY 3 Insulation Invinsa Roof Board Membrane
Not
es
Thic
knes
s,
min
.
Atta
chm
ent
Atta
chm
ent
Rate
Atta
chm
ent
Rate
Stee
l
1A-90 N
144245-144211-0
0.5 (42) 1.5" (38 mm) LL
UF/UF
16/board - 1 per 2 ft2 (0.19 m2) CAA 2 gal/100 ft2
(8.15 l/m2)
2-Ply (CAA)
144245-144212-0 3-Ply (CAA)
144245-144213-0 4-Ply (CAA)
Conc
rete 144247-144211-0
AP/UF
2-Ply (CAA)
144247-144212-0 3-Ply (CAA)
144247-144213-0 4-Ply (CAA)
8
FM Global® ApprovalsJM EPDM — Fastened Insulation with Subsequent Layers Fully Adhered
Deck
Typ
e
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #
Insu
latio
n
Insu
latio
nFa
sten
er
Insu
latio
n Fa
sten
er R
ate
(#
: ft2 )
Cove
r Boa
rd
Cove
r Boa
rd
Adhe
sive
Cove
r Boa
rd
Adhe
sive
Rat
e (#
“ OC
)
Mem
bran
e Ad
hesi
ve
Slop
e (#
”: 1
ft)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(Cla
ss)
Exte
rnal
Fire
(Cla
ss)
Hail
Ratin
g
Cem
entit
ious
W
ood
Fibe
r
N368880-0-0
E3Gyptec 1:2
I 2P UIA, HA 12" LVOC, SB, WB 160
1 A SH368881-0-0 2P UIA, HA 12" * 90
* Asphaltic Base Sheet attached with Olylok 9" OC in the lap and two staggered rows of 18" OC.
FM Global® ApprovalsJM EPDM R — Mechanically Fastened Membrane
Deck
Typ
e
Appl
icat
ion
Type
Deck
Gra
de1 (K
SI)
Roof
Nav
SM
Asse
mbl
y #
Insu
latio
n2
Cove
r Boa
rd
Slop
e (#
”: 1
ft)
Mem
bran
e W
idth
(ft)
Mem
bran
e Fa
sten
er
Mem
bran
e Fa
sten
er
Spac
ing
(#“
OC)
Win
d Up
lift
(PSF
)
Inte
rnal
Fire
(Cla
ss)
Exte
rnal
Fire
(Cla
ss)
Hail
Ratin
g
Stee
l
N 80
317960-0-0
E3 I, I FR 1 10'
HL
6"
90
1 A SH
324306-0-0 HL (w/RPS)317964-0-0 HL
75324310-0-0
HL (w/RPS)RC 33
325085-0-0 105324312-0-0 90324316-0-0 75
Notes1. Deck Grade and assemblies vary. Please check RoofNav for specific deck constructions of individual approvals.2. All E3 insulation for new roofs is 1.5" min unless otherwise listed. Re-Cover insulation thickness varies by approval. Please check individual listings.3. Other urethane adhesives may be available in the referenced approvals. Check application rate for all approvals listing hot asphalt (HA) as an adhesive. Please check listing for all adhesive options.
This is intended to serve as a reference guide, please check RoofNav for the most current information and assembly details.FM Global and RoofNav are among the trademarks or registered trademarks of Factory Mutual Insurance Company and FM Approvals LLC, respectively.
Insulation/Cover BoardE3 = ENRGY 3® I = Invinsa® Roof Board I FR = Invinsa® FR Roof Board LL = Loose Laid
Application TypeN = New Roof RC = Re-Cover
Fastener and PlateAP = All Purpose HL = High Load®
RPS = Reinforced Perimeter Strip UF = UltraFast®
Insulation/Cover Board AdhesiveHA = Hot Asphalt2P UIA = JM Two-Part Urethane Insulation Adhesive
Membrane AdhesiveCAA = JM Cold Application AdhesiveLVOC = JM Low VOC SB = JM Solvent Based WB = JM Water Based
Deck
Typ
e
FM
Ratin
g
Appl
icat
ion
Type
Roof
Nav
SM
Asse
mbl
y #
Slop
e
ENRGY 3 Insulation Invinsa Roof Board Membrane
Not
es
Thic
knes
s,
min
.
Atta
chm
ent
Rate
Atta
chm
ent
Rate
Atta
chm
ent
Stee
l 1A-90
N
262904-137159-01 (83)
1.5" (38 mm)LL – UF/UF plastic
16/board - 1 per 2 ft2 (0.19 m2)
Self-Adhering
2-Ply (HW)1A-165 262905-137159-0 2" (51 mm) 32/board - 1 per 1 ft2
(0.09 m2)
Conc
rete
NC A-210 162901-77921-0
0.75 (63)1.5" (38 mm)
UIA 0.75" (19 mm) @ 12" (31 cm)
o.c.
UIA, MBR BA 0.75" (19 mm) @ 12" (31 cm) o.c. 2-Ply (SA)
NC A-225162904-77921-0 UIA, 2P UIA
MBR BA 1.5 gal/100 ft2 (6.04 l/m2)RC 162907-77921-0 – – – ALL, 2-Ply
(SA)
FM Global® Approvals JM SBS Systems — Self-Adhering
Deck
Typ
e
Appl
icat
ion
Type
Clas
s
Max
. Slo
pe
in./f
t (m
m/m
)
Insu
latio
n
Cove
r Boa
rd
Mem
bran
e
Atta
chm
ent
Met
hod
UL N
umbe
r*
Non
com
bust
ible
N
A
1 (83)
E3 (Optional)
I
JM EPDM
Fully Adhered
EPDM-42
2 (167)EPDM-43
JM PVC FB PVC-18
1 (83)JM PVC
PVC-28
2 (167) Mechanically Fastened PVC-36
0.5 (42) JM TPO
Fully Adhered TPO-17
1 (83)Mechanically Fastened
TPO-33
0.5 (42)
JM SBS
SBS-Hot-9
Self-Adhering SBS-Hot-39
Fully Adhered SBS-Cold-3
Com
bust
ible
JM BUR Mechanically Fastened BUR-14
I FR**
JM TPO
Fully Adhered TPO-11,12
1 (83)Mechanically Fastened
TPO-21
B 2 (167) TPO-2
A
0.5 (42) JM TPO FBFully Adhered
TPO-15,18
1 (83)JM PVC
PVC-4
2 (167)
Mechanically Fastened PVC-7
JM PVC FBFully Adhered
PVC-34
JM PVC SDPVC-21,27
Mechanically Fastened PVC-13
0.75 (63)
JM EPDM RFully Adhered
EPDM-47
1 (83) EPDM-50
0.75 (63) Mechanically Fastened EPDM-14
2 (167)JM EPDM NR or FR Fully Adhered
EPDM-43
1 (83) EPDM-52
UL® External Fire Resistance (UL 790) Major Approvals — Invinsa Roof Board — New Construction
For more detailed application or code and approval information, please contact your JM representative or call us at (800) 922-5922.FM Global and RoofNav are among the trademarks or registered trademarks of Factory Mutual Insurance Company and FM Approvals LLC, respectively.
* UL Number refers to constructions (paragraph) in JM’s UL 790 listing.
9
Application TypeN = New Roof RC = Re-Cover
Adhesive 2P UIA = JM Two-Part Urethane Insulation Adhesive UIA = JM Urethane Insulation Adhesive MBR BA = MBR Bonding Adhesive
Fasteners and Plates UF = UltraFast® RhP = RhinoPlate®
Membrane Adhesive LL = Loose Laid
Membrane NotesPVC FB = Fleece-Backed PVC MP = Any Multi-Ply Cover (existing roof) ALL = Any Membrane Cover (existing roof) HW = Heat Weld SA = Self-Adhering SP = Any Single Ply Cover (existing roof)
Insulation/Cover BoardE3 = ENRGY 3®
** A minimum 1/4" thick layer of “Invinsa® FR” can be used in lieu of “Invinsa®” in any existing non-combustible deck Classification. This can be above or below additional insulation layers described in the Certified roofing system. The resulting roofing assembly can be used over a combustible roof deck (minimum 15/32" plywood). All insulation joints must be staggered a minimum of 6" from the deck joints and from the insulation joints directly below. The maximum incline shall be in accordance with the Certification established for the original roofing system as listed in UL’s Roofing Materials & Systems Directory; however the incline cannot exceed 3:12.In cases where Invinsa or Invinsa FR is not specifically called out in an assembly the following applies per TGFU.R10167: “Invinsa®” may be used over “ENRGY 3®”, or as an acceptable alternate to “ENRGY 3®”, in any of the following Classifications.
RS-5503 11-15 (Replaces 8-14)
717 17th St.Denver, CO 80202(800) 922-5922www.jm.com/roofing
To ensure quality workmanship and top-notch installation, JM offers its Peak Advantage Contractor Program. Contractors selected to participate are proven to be best in class, having lived up to the highest performance standards. These contractors have access to JM’s strongest guarantees. To be assured of the best possible results on the roofing system you specify, make sure it’s installed by a JM Peak Advantage Contractor.
Johns Manville designs roofing products that work together to provide a one-source comprehensive roofing system solution. Total roofing system guarantees are available under the JM Peak Advantage Guarantee program. To learn more about our standard guarantee terms and conditions or talk to your local JM sales representative.
JM Peak Advantage Guarantees are available only on qualified JM roofing systems containing JM roofing products. JM standard product terms and conditions will apply to include a one-year limited product warranty.
Product Warranties
Peak Advantage Contractor Program
