INVENTORY CLEARANCE...FEATURES AND BENEFITS • With threaded holes in order to balance with...
4
FEATURES AND BENEFITS • With threaded holes in order to balance with supplied balancing screws • Improved concentricity • Improved balance design with no moving pieces • Low Centrifugal Forces due to low holder mass • For maximum gripping power with exceptional concentricity. • Concentricity of ≤.0001” with tool shrunk in holder. • Chip load distributed evenly along cutting edge of tool which results in longer tool life. • Constructed of double tempered Tool Steel for exceptional durability and cycle life. With proper use, toolholder life should exceed that of standard end mill holders. • Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force. • Short projections are possible because no mechanical clamping devices are used. This results in greater rigidity and resistance to bending. • Simple and fast to use. The total time elapsed to remove one cutting tool and insert another is less than 10 seconds. • Through-spindle coolant capability. • Coolant through holders require no special backup screws or seals. The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves. The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use. BALANCEABLE SHRINK FIT TOOLING Shrink Fit Machines • Heating: Induction • Shrinking Time: 6-15 seconds • Power: 220VAC 50/60HZ single phase • Rated Ampere: 20A • Power Consumption: 4KW • Dimensions: 292mm(W) x 302mm(D) x 660mm(H) • Induction Head Inside Diameter: 35mm • Taper support: All HSK, BT, CAT & SK Tapers • Display: LED • For use with Carbide tools only • Max. Tool Diameter 25mm • Cooling: Shop air attached to head 0-10 min. • Heating: Induction • Shrinking Time: 3-5 seconds • Power: 220VAC 50/60HZ 3 phase • Rated Ampere: 27A • Power Consumption: 10KW • Dimensions: 350mm(W) x 400mm(D) x 660mm(H) • Induction Head Inside Diameter: 35mm • Taper support: All HSK, BT, CAT & SK Tapers • Display: LCD • For use with Carbide, HSCO & HSS tools • Max. Tool Diameter 25mm • Cooling: Shop air attached to head 0-10 min. Model GTS-306 LUXE Model GTS-9000M Model Code No. SALE $ GTS9000M 536-655 8,540.04 Requires using a balancing machine ASK US ABOUT SPECIAL PACKAGE PRICING! INVENTORY CLEARANCE Model Code No. SALE $ GTS306 LUXE 536-650 4,665.54 PROMO PRICING ONLY WHILE QUANTITIES LAST
Transcript of INVENTORY CLEARANCE...FEATURES AND BENEFITS • With threaded holes in order to balance with...
FEATURES AND BENEFITS• With threaded holes in order to balance with supplied balancing screws• Improved concentricity• Improved balance design with no moving pieces• Low Centrifugal Forces due to low holder mass• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Chip load distributed evenly along cutting edge of tool which results in longer tool life.• Constructed of double tempered Tool Steel for exceptional durability and cycle life. With proper use, toolholder life should exceed that of standard end mill holders.
• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.• Short projections are possible because no mechanical clamping devices are used. This results in greaterrigidity and resistance to bending.
• Simple and fast to use. The total time elapsed to remove one cutting tool and insert another is less than 10 seconds.• Through-spindle coolant capability.• Coolant through holders require no special backup screws or seals. The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves. The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use.
BALANCEABLE SHRINK FIT TOOLING
Shrink Fit Machines
• Heating: Induction• Shrinking Time: 6-15 seconds• Power: 220VAC 50/60HZ single phase• Rated Ampere: 20A• Power Consumption: 4KW• Dimensions: 292mm(W) x 302mm(D) x 660mm(H)• Induction Head Inside Diameter: 35mm• Taper support: All HSK, BT, CAT & SK Tapers• Display: LED• For use with Carbide tools only• Max. Tool Diameter 25mm• Cooling: Shop air attached to head 0-10 min.
• Heating: Induction• Shrinking Time: 3-5 seconds• Power: 220VAC 50/60HZ 3 phase• Rated Ampere: 27A• Power Consumption: 10KW• Dimensions: 350mm(W) x 400mm(D) x 660mm(H)• Induction Head Inside Diameter: 35mm• Taper support: All HSK, BT, CAT & SK Tapers• Display: LCD• For use with Carbide, HSCO & HSS tools• Max. Tool Diameter 25mm• Cooling: Shop air attached to head 0-10 min.
Model GTS-306 LUXE Model GTS-9000M
Model Code No. SALE $GTS9000M 536-655 8,540.04
Requires using a balancing machine
ASK US ABOUT SPECIAL PACKAGE PRICING!
INVENTORY CLEARANCE
Model Code No. SALE $GTS306 LUXE 536-650 4,665.54
PROMO PRICING ONLY WHILE QUANTITIES LAST
CAT 40 Balanceable Shrink Fit Holders
Hole GaugeTaper Dia. (d) Length (A) D2 D3 L Code No. SALE $
InchCAT40 1/8 3.15” 0.39” 0.75” 0.35” 531-838 142.56 CAT40 3/16 3.15” 0.39” 0.75” 0.47” 531-840 142.56 CAT40 1/4 3.15” 0.83” 1.06” 1.42” 531-842 142.56 CAT40 1/4 6.30” 0.83” 1.06” 1.42” 531-844 167.94 CAT40 5/16 3.15” 0.83” 1.06” 1.42” 531-846 142.56 CAT40 5/16 6.30” 0.83” 1.06” 1.42” 531-848 167.94 CAT40 3/8 3.15” 0.94” 1.26” 1.65” 531-850 142.56 CAT40 3/8 6.30” 0.94” 1.26” 1.65” 531-852 167.94 CAT40 1/2 3.15” 0.94” 1.26” 1.65” 531-854 142.56 CAT40 1/2 6.30” 0.94” 1.26” 1.65” 531-856 167.94 CAT40 5/8 3.15” 1.06” 1.34” 1.97” 531-858 142.56 CAT40 5/8 6.30” 1.06” 1.34” 1.97” 531-860 181.98 CAT40 3/4 3.15” 1.30” 1.65” 2.05” 531-862 142.56 CAT40 3/4 6.30” 1.30” 1.65” 2.05” 531-864 167.94 CAT40 1 3.94” 1.73” 2.09” 2.28” 531-866 142.56 CAT40 1 6.30” 1.73” 2.09” 2.28” 531-868 167.94 CAT40 1-1/4 3.94” 1.73” 2.09” 2.28” 531-870 142.56 CAT40 1-1/4 6.30” 1.73” 2.09” 2.28” 531-872 212.76
MetricCAT40 8 80 21 27 36 531-810 142.56 CAT40 10 80 24 32 42 531-814 142.56 CAT40 12 80 24 32 47 531-818 142.56
Hole GaugeTaper Dia. (d) Length (A) D2 D3 L Code No. SALE $
InchCAT50 1/4 6.30” 0.83” 1.06” 1.42” 531-934 212.76 CAT50 5/16 3.15” 0.83” 1.06” 1.42” 531-936 181.98 CAT50 3/8 3.15” 0.94” 1.26” 1.65” 531-940 181.98 CAT50 1/2 3.15” 0.94” 1.26” 1.65” 531-944 181.98 CAT50 1/2 6.30” 0.94” 1.26” 1.65” 531-946 212.76 CAT50 5/8 3.15” 1.06” 1.34” 1.97” 531-948 181.98 CAT50 3/4 3.15” 1.30” 1.65” 2.05” 531-952 181.98 CAT50 1 3.94” 1.73” 2.09” 2.28” 531-956 181.98 CAT50 1 6.30” 1.73” 2.09” 2.28” 531-958 227.34 CAT50 1-1/4 3.94” 1.73” 2.09” 2.28” 531-960 181.98 CAT50 1-1/4 6.30” 1.73” 2.09” 2.28” 531-962 269.46
MetricCAT50 8 80 21 27 36 531-904 181.98 CAT50 10 80 24 32 42 531-908 181.98 CAT50 12 80 24 32 47 531-912 181.98 CAT50 16 80 27 34 50 531-916 181.98 CAT50 25 100 44 53 58 531-924 199.26
30k
CAT 40PremiumBalanced
RPM
CAT 50 Balanceable Shrink Fit Holders
25k
CAT 50PremiumBalanced
RPMComplete with certificate Complete with certificate
• With threaded holes in order to balance with supplied balancing screws• Coolant thru the spindle capability• Pre-Balanced up to 30,000 rpm• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.
• Back up screws are available on request
• With threaded holes in order to balance with supplied balancing screws• Coolant thru the spindle capability• Pre-Balanced up to 25,000 rpm• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.
• Back up screws are available on request
SHRINK FIT TOOLING
®
1-800-265-8221 • [email protected]
www.SowaTool.com
PROMO PRICING ONLY WHILE QUANTITIES LAST
Hole GaugeTaper Dia. (d) Length (A) D2 D3 L Code No. SALE $
InchBT40 1/8 3.54” 0.39” - 0.35” 532-464 167.94 BT40 3/16 3.54” 0.39” - 0.47” 532-466 167.94 BT40 1/4 3.54” 0.83” 1.06” 1.42” 532-468 167.94 BT40 1/4 6.30” 0.83” 1.06” 1.42” 532-470 179.70 BT40 3/8 3.54” 0.94” 1.26” 1.65” 532-476 142.56 BT40 3/8 6.30” 0.94” 1.26” 1.65” 532-478 181.98 BT40 1/2 3.54” 0.94” 1.26” 1.65” 532-480 142.56 BT40 1/2 6.30” 0.94” 1.26” 1.65” 532-482 167.94 BT40 5/8 3.54” 1.06” 1.34” 1.97” 532-484 167.94 BT40 3/4 6.30” 1.30” 1.65” 2.05” 532-490 167.94 BT40 1-1/4 3.94” 1.73” 2.09” 2.28” 532-496 167.94
MetricBT40 6 90 21 27 36 532-432 167.94 BT40 8 90 21 27 36 532-436 142.56
Hole GaugeTaper Dia. (d) Length (A) D2 D3 L Code No. SALE $
InchBT30 1/8 3.15” 0.39” - 0.35” 532-414 139.32 BT30 3/16 3.15” 0.39” - 0.47” 532-416 139.32 BT30 1/4 3.15” 0.83” 1.06” 1.42” 532-418 139.32 BT30 1/2 3.15” 0.94” 1.26” 1.65” 532-424 139.32
SHRINK FIT TOOLING
®
1-800-265-8221 • [email protected]
www.SowaTool.com
BT 30 Balanceable Shrink Fit Holders
20k
BT 30PremiumBalanced
RPM
BT 40 Balanceable Shrink Fit Holders
30k
BT 40PremiumBalanced
RPM
• With threaded holes in order to balance with supplied balancing screws• Coolant thru the spindle capability• Pre-Balanced up to 20,000 rpm• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.
• Back up screws are available on request
• With threaded holes in order to balance with supplied balancing screws• Coolant thru the spindle capability• Pre-Balanced up to 30,000 rpm• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.
• Back up screws are available on request
Complete with certificate Complete with certificate
PROMO PRICING ONLY WHILE QUANTITIES LAST
®
1-800-265-8221 • [email protected]
www.SowaTool.com
HSK 63A Balanceable Shrink Fit Holders
30k
HSK 63PremiumBalanced
RPM
HSK 100A Balanceable Shrink Fit Holders
25k
HSK 100PremiumBalanced
RPM
• With threaded holes in order to balance with supplied balancing screws• Coolant thru the spindle capability• Pre-Balanced up to 30,000 rpm• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.
• Back up screws are available on request
Complete with certificate Complete with certificate
• With threaded holes in order to balance with supplied balancing screws• Coolant thru the spindle capability• Pre-Balanced up to 25,000 rpm• For maximum gripping power with exceptional concentricity.• Concentricity of ≤.0001” with tool shrunk in holder.• Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force.
• Back up screws are available on request
SHRINK FIT TOOLING
Distributed by:
Printed in Canada
Pricing valid until further notice or while quantities last.
Hole GaugeTaper Dia. (d) Length (A) D2 D3 L Code No. SALE $
InchHSK100A 3/8 6.30” 0.94” 1.26” 1.65” 536-442 281.34 HSK100A 1/2 3.74” 0.94” 1.26” 1.65” 536-444 255.96 HSK100A 1/2 6.30” 0.94” 1.26” 1.65” 536-446 281.34 HSK100A 5/8 6.30” 1.06” 1.34” 1.97” 536-450 281.34 HSK100A 3/4 4.13” 1.30” 1.65” 2.05” 536-452 255.96 HSK100A 3/4 6.30” 1.30” 1.65” 2.05” 536-454 281.34 HSK100A 1 6.30” 1.73” 2.09” 2.28” 536-458 281.34 HSK100A 1-1/4 6.30” 1.73” 2.09” 2.28” 536-462 281.34
Hole GaugeTaper Dia. (d) Length (A) D2 D3 L Code No. SALE $InchHSK63A 1/4 3.15” 0.83” 1.06” 1.42” 536-342 173.34 HSK63A 5/16 3.15” 0.83” 1.06” 1.42” 536-346 173.34 HSK63A 5/16 6.30” 0.83” 1.06” 1.42” 536-348 224.64 HSK63A 3/8 3.35” 0.94” 1.26” 1.65” 536-350 173.34 HSK63A 3/8 6.30” 0.94” 1.26” 1.65” 536-352 224.64 HSK63A 5/8 3.74” 1.06” 1.34” 1.97” 536-358 173.34 HSK63A 5/8 6.30” 1.06” 1.34” 1.97” 536-360 224.64 HSK63A 3/4 3.94” 1.30” 1.65” 2.05” 536-362 173.34 HSK63A 3/4 6.30” 1.30” 1.65” 2.05” 536-364 224.64 HSK63A 1 4.53” 1.73” 2.09” 2.28” 536-366 173.34 HSK63A 1 6.30” 1.73” 2.09” 2.28” 536-368 224.64 HSK63A 1-1/4 4.72” 1.73” 2.09” 2.28” 536-370 173.34 HSK63A 1-1/4 6.30” 1.73” 2.09” 2.28” 536-372 224.64 MetricHSK63A 6 80 21 27 36 536-306 173.34 HSK63A 8 80 21 27 36 536-310 173.34 HSK63A 10 85 24 32 42 536-314 173.34 *USF2192*
PROMO PRICING ONLY WHILE QUANTITIES LAST
