Introduction RW Series Overview › cpws › docs › rw › RW QSG.pdf · RW Series Overview (RW...
Transcript of Introduction RW Series Overview › cpws › docs › rw › RW QSG.pdf · RW Series Overview (RW...
RW
Series
Quick
Start G
uid
e
1
RW
Series
RW
Series
RW
Series
RW
Series
RW
Series
RW
Series
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
© ZIH Corp 2013 QSG-RWS-003 Rev. B
IntroductionThank you for choosing one of our Zebra
RW Series™ Mobile Printers. These rugged printers will become productive and efficient
additions to your workplace thanks to their innovative de-sign. Because they are made by Zebra Technologies you can be assured of world-class support for all of your bar code printers, software, and supplies.
RW 420 RW 220
Media width:2 in. [51 mm] to 4.12 in. [105 mm]
Media width:1 in. [25.4 mm] to 2.37 in [60 mm].
L: 7.4 in. [188 mm]*W: 6.3 in. [160 mm]H: 3.7in. [94 mm] max.**w/ belt clip & card reader option
L: 6.8 in. [173.6 mm]*W: 4.4 in.[111.8 mm]H: 3.7 in. [94.1 mm]**w/ belt clip & card reader option
This document provides an easy reference for operating and maintaining the RW Series of Mobile Printers. Complete and current documentation for each model printer
is provided by the RW Series User Guide available on the Internet at: www.zebra.com/manuals.
Always refer to the Important Safety Information data sheet shipped with each printer and the Technical Bulletin shipped with each battery pack. These documents detail procedures to ensure maximum reliability and safety while using this printer.
RW Series Overview(RW 420 Illustrated)
1. Platen Roller 2. Bar Sensor 3. Media Support Disks 4. Printhead 5. Latch Release Button 6. Magnetic Stripe Reader (MSR) Slot 7. Communications Port Door 8. “D” Rings 9. Control Panel 10. Smart Card Slot 11. Gap Sensor 12. Bottom Media Feed Slot 13. Media Cover 14. Communications Port 15. Docking Connector Cover 16. Battery 17. Battery Charging Receptacle 18. Belt Clip
15
16
14
1
2
5
6
7
3
4
18
8
9
11
10
12
13
17
2
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Charge the Battery
Using the LI72 Single ChargerInsert the plug from the charger cable into the battery
pack’s charger jack. Plug the charger into the A.C. outlet. The light on the front of the charger will indicate the bat-
tery pack’s charge status.Consult the RW series User’s Guide available at
www.zebra.com/manuals for complete information on us-ing the various versions of the Model LI72 Single Charger.
Batteries are shipped uncharged. Remove protective shrink-wrap and labels from new battery packs and allow them to charge completely prior to initial use.
Do not charge the battery while using the printer! Charge the battery pack when removed from the Printer
for best results.
Installing the Battery
Insert the Battery Pack into the Printer
Rotate the Battery Pack into the Printer until the latch clicks into place.
Battery
2
Section Continues
LI72 Battery Charger
Charger Jack
Rotate Belt Clip out of the way.
Insert this end of the Battery Pack into the Printer
Rotate the Battery Pack into the Printer until the latch clicks into place.
Battery
RW 420 Battery Installation
Rotate Belt Clip out of the way.
RW 220 Battery Installation
3
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
3
Section Continues
Loading Media
Load the Media Roll
Pull Media Supports apart as shown.
Press Latch Button
Media Cover Opens
Close Media Cover
Pull Media out of Printer
Open the Media Cover
Media RollNote direction media pulls o¥ the roll.
Close the Media Cover
4
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Connect The Printer With a CableYou can connect your printer to a terminal or a PC us-
ing either RS232C or USB protocols. Refer to the Label Vista™ application available on the RW product CD or at www.zebra.com/software for help on setting up communi-cations with your printer.
Connect the Printer by Infrared (IR) or RadioIf your RW series printer has the optional IR module, you can make
wireless line-of-sight connections to other IR equipped devices us-ing the standard IrDA protocol.If your RW series printer has a radio option, you can connect wire-
lessly to either a terminal or a wireless network (WLAN.) Refer to the Mobile Printer Wireless Configuration Guide available on the product CD or at www.zebra.com/utilities for help on setting up wireless communications with your printer.Cable Communications with a Terminal.
Cable Communications with a P.C.If you are using a USB cable to connect to a PC you
may need to install the Zebra Universal Driver available at: www.zebra.com/drivers.
Connect the Printer
Communications Cable to Terminal
Communications Port
Terminal
RW Series Printer with wireless option
Terminal with wireless communications ability
RS-232C or USB Communications Cable to ComputerRefer to Appendix A in the User Guide for part numbers.
USB Connector
RS232 Connector
5
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e Zebra RW 420Signal:0%Battery (ok) Latch: ok Rdr MENU
Zebra RW 420Signal:0%Battery (ok) Latch: ok Rdr MENU
Printer ControlsLCD Keypad
Area Method Interval
Printhead
Use a Zebra cleaning pen or 70% isopropyl alcohol on a cotton swab to clean the print elements from end to end (the print elements are located in the thin gray line on the printhead).
After every § ve rolls of media (or more often, if needed)
PlatenRotate the platen roller and clean it thoroughly with the cleaning pen or 70% isopropyl alcohol and a cotton swab.
Tear bar Clean thoroughly with the cleaning pen or 70% isopropyl alcohol and a cotton swab.
Exterior Water dampened cloth As needed
Interior Brush/air blow. Ensure the Bar Sensor and Gap Sensor windows are free of dust.
After every § ve rolls of media (or more often, if needed)
Cleaning the Printer
Caution • To avoid possible personal injury or damage to the Printer, never insert any pointed or sharp objects into the Printer.
5
Section Continues
POWER BUTTONPress to turn unit on. Press again to turn unit o¥ .
SELECT BUTTONPress to select a menu choice on the LCD.
PRINTER STATUS ICONSIndicates the status of several Printer functions.
FEED BUTTONPress to advance the media one blank label or a software deter-mined length of journal media.
SCROLL BUTTONPress to scroll through the menu choices on the LCD.
MAG/SMART CARD READER INDICATORWhen “RDR” is displayed the Mag Stripe/ Smart Card reader is enabled.
Tear Bar
Bar Sensor
Gap Sensor
Printhead Elements
Platen Surface
6
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Using the Magnetic Stripe Reader The Magnetic Stripe and Smart Card Readers are an optional
feature of the RW series. Your printer may be con§ gured without them.
Using the Smart Card Reader
The status of the Magnetic Stripe Reader (MSR) is indicated in three possible ways:
• Reader status is displayed on the Main Menu LCD• The LCD backlight flashes to indicate status (3 flashes = en-
abled, 2 flashes = disabled).• Chimes indicates the reader status (3 chimes = enabled, 2
chimes = disabled).The MSR is used as follows:
1. When the reader is enabled, place the card into the reader slot as shown above. The magnetic stripe must face the bot-tom of the printer, and be inserted into the card reader slot as shown above.
2. Slide the card through the slot in either direction. Depending on the application software, the printer will sound one chime when a scan is successful .
3. If the card did not read, slide it back through the slot in the opposite direction.
The optional Smart Card reader is used as follows:1. The LCD will display “RDR” to indicate the Smart Card Reader is
active. (Some reader applications may flash the display back-light and/or chime three times to indicate the reader status is “ready.”) The printer is now acting only as a Smart Card reader connected to the host terminal; all other printer functions are suspended.
2. Insert the card into the reader slot as shown above. The micro-chip imbedded in the card must be oriented facing the bottom of the printer and must be completely inserted into the reader slot to scan successfully .
3. Depending on the application software, the printer will sound a chime after a successful transaction.
4. After the card has been successfully read the printer can re-sume normal printing operations and the Smart Card can be re-moved
Card can be read in both directions.
Magnetic Stripe Card Reader Slot
Smart Card Reader Slot
Insert Smart Card completely into printer.
Insert Smart Card into slot with microchip facing the bottom of the printer as shown.
Place the Magnetic Stripe Card in the reader slot with the magnetic stripe facing the bottom of the printer as shown.
7
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
LCD Control PanelThe top of the display shows icons indicating various printer functions. Check the icon’s status and refer to the referenced Troubleshoot-
ing topic on the following pages.
Troubleshooting
Zebra RW 420Signal:0%Battery (ok) Latch: ok Rdr MENU
Zebra RW 420Signal:0%Battery (ok) Latch: ok Rdr MENUIcon Status Indication Ref. to Topic #
on next pageOn Bluetooth Link established n/a
O¥ No Bluetooth Link 5
On Bluetooth link established n/a
O¥ No Bluetooth link 5
Flashing Transmitting/Receiving data n/a
On 802.11x RF Link established n/a
O¥ No 802.11x RF Link 5
Flashing Low Battery 3, 5, 6,
Flashing Head latch not closed 8, 10, 11
Flashing Indicates Printing activity n/a
Steady Data processing in process 7
Flashing Out of Media 9,11
Blank Screen n/a No application
RW series printers may be built with one of two LCD types. LCDs using the Bluetooth icon (highlighted by a gray background in the table above) will gradually replace LCDs with the “light bulb” icon indicating Bluetooth activity. Printers with either type of display will function identically.
7
Section Continues
PRINTER STATUS ICONS
8
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Troubleshooting Topics
1. No power:• Check that battery is installed properly.• Recharge or replace battery as necessary.
2. Media does not feed:• Be sure printhead is closed and latched.• Check spindle holding media for any binding.• Ensure label sensor is not blocked.
3. Poor or faded print or icon ̄ashing:• Clean printhead.• Check battery for possible damage. Recharge or replace as necessary.
Always dispose of batteries properly. Refer to Appendix E of the RW series User Guide for more information.
• Check quality of media.
4. Partial or missing print:• Check media alignment.• Clean printhead.• Ensure printhead is properly closed and latched.
5. No print:• Replace battery.• Check cable to terminal.• (Wireless units only) Restore wireless connection.
6. Reduced battery life:• Check battery date code — if battery is one to two years old, short life may be due to normal aging.• Replace battery.
7. Flashing icon:• No application or application corrupted; program must be re-loaded.• (Wireless units only): flashing error light indicates data transmission.
8. Flashing or icons:• Check that media is loaded and that printhead is closed and securely latched.
9. Skips labels:• Ensure correct media is being used.• Ensure bar/ or gap sensor is not blocked.
10. Communication Error:• Check media is loaded, head is closed and error light is off.• Replace cable to terminal.
8
Section Continues
9
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
11. Label Jam:• Open media cover.• Generously apply alcohol to Printer in area of jammed label.
12. Blank LCD Screen:• No application loaded or application corrupted: program must be re-loaded.
13. Magnetic Strip Card or Smart Card Won’t Read• Ensure the “RDR” text is displayed, indicating card reader is enabled. • Ensure card is inserted with the magnetic stripe or microchip facing in the correct direction.• Check card for excessive wear or damage to either the magnetic strip or the microchip.
14. Battery Pack Is Hard to Insert• Do not force the battery. Verify you have removed the protective shrink-wrap which protects the battery during shipping.• The battery packs for the RW and QL series model printers are similar in size and shape, but not identical. Verify you are using the
correct battery pack: The RW 420 battery pack replacement part number is AK17463-005. The RW 220 battery pack replacement part number is
AK18026-002.
10
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Using the AccessoriesBelt Clip (standard on all printers) Adjustable Shoulder Strap (optional)
To use: hook the clip over your belt and ensure that the clip is securely attached to the belt. The belt clip will pivot to allow you to move freely while wearing the printer.
Refer to figure below. Snap each end of the shoulder strap into the “D” rings in the top of the printer. Hold the buckle and slide the strap as shown below until you achieve the desired length.
10
Section Continues
Printer can pivot freely
Hold Buckle
Pull Strap here to lengthen
Pull Strap here to shorten
Snap in to “D” rings on Printer
Clip Printer to belt
11
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Using the AccessoriesRW 420 Vehicle Cradle When the RW 420 Printer is “docked” in the Vehicle Cradle it can
print, receive and transmit data and the cradle can charge the printer’s batteries. Refer to the documentation either in the Users Guide or supplied with the Cradle for more information.
Installing the Printer• As a safety precaution, remove the
shoulder strap prior to docking the printer.
• Remove the Docking Connector Cover from the bottom of the printer, and re-tain it for future use.
• Place the bottom of the printer over the two pins in the Cradle.
• Rock the top of the printer into the Cradle and press firmly until it latches in place.
• When the power indicator on the Cradle is lit turn the printer on.
RW 220 Vehicle CradleThe RW 220 can be used in conjunction with a docking Cradle. When
the Printer is “docked” it can be powered by either its own battery or one of the RCLI series of external chargers. Refer to the documenta-tion supplied with the Cradle for more information.
Removing the Printer• Turn the Printer off. • Push on the latch on the
Cradle and rotate the Printer away from the Cradle.
• Lift the Printer free of the cradle locating pins and out from the Cradle.
Installing the Printer• Place the bottom of
the printer over the two pins in the Cra-dle.
• Rock the top of the printer into the Cradle and press firmly until it latches in place.
Removing the Printer• Turn the printer off. • Push on the latch on the Cradle
and rock the top of the printer away from the Cradle.
• Lift the printer out from the Cradle.
Replace the Docking Connec-tor Cover if you will be using the printer for an extended period of time away from the Cradle.
Place the printer over the retaining pins in the Cradle.
Press the Latch button to release the printer.
Rock the printer into the Cradle to latch it in position.
Lift the printer free of the locating pins.
Remove and retain the Docking Connec-tor Cover
Rotate the printer out of the Cradle.
Place the Printer over the retaining pins in the Cradle.
Lift the printer free of the retaining pins.
Lift the latch button to release the printer.
Rotate the printer out of the Cradle.
Rock the Printer into the Cradle to latch it in position.
12
Intro
duct
ion
Get
ting
Star
ted
Usin
g th
e Pr
inte
r
Trou
bles
hoot
ing
Acce
ssor
ies
Cont
act U
s
RW
Series
Quick
Start G
uid
e
Zebra Technologies Corporation475 Half Day Road, Suite 500Lincolnshire, IL 60069 USAT: +1 847.634.6700 or +1 800.423.0442
Product Support
For product support, and the latest versions of all customer documentation, contact Zebra Technologies at: www.zebra.comRefer to Appendix D in the RW Series User Guide for more detailed contact information
IN THE AMERICAS CONTACT:
Zebra Technologies Corporation475 Half Day Road, Suite 500Lincolnshire, Illinois 60069 USAPhone: +1.847.634.6700 or +1.800.423. 0422Fax: +1.847.913.8766
IN EUROPE, AFRICA, THE MIDDLE EAST, AND INDIA CONTACT:
Zebra Technologies Europe LimitedDukes MeadowMillboard RoadBourne EndBuckinghamshire SL8 5XF, UKT: +44 (0)1628 556000F: +44 (0)1628 556001
IN THE ASIA PACIFIC REGION CONTACT:
Zebra Technologies Asia Paci§ c, LLC 71 Robinson Road #05-02/03Singapore 068895T: +65-6858 0722F: +65-6885 0838