REDS Interactive Whiteboard

Technical Support by TW Trade Technology, LLC.

A Smart, Easy, and Cost-Saving Solution

What is REDS Interactive Whiteboard?

How to assembly the equipment ?

How to start for first time using? How to solve the problems in the course of using

REDS Interactive Whiteboard

Gouis Co., Ltd. www.gouis.com

REDS Interactive whiteboard can make teachers quickly master the skill inheriting traditional teaching habits. In writing mode, the traditional teaching habits is kept, teachers can writing, painting, erase, choosing any color according to his needing and idea. After preparation of the calibration which confirm projection area and the relative projector position, and fixing project resolution, the IR interactive kit can catch IR signal into the mouse pointer moving, clicking action. With different whiteboard software or drawing application, the IR interactive kit can real-time control computer operation, and content changing will real-time display on the projection area.

REDS Interactive Whiteboard

What is REDS Interactive Whiteboard? ？

REDS Interactive Whiteboard

How to assembly the equipment ?

2. Connect the other side of USB wire to the REDS receiver.

1. Prepare the USB wire, connect the flat mouth of data wire into USB port of PC. computer

Installation Completed

How to start for first time using？Step 1

Step 1:Copy the whiteboard driver on your desktop

Step 2

Step 2:Double-click the software icon Or Right-click the software icon to open it

Notice: OK----The software icon will appear in the bottom right corner of the screenNG----USB is not connected to the device

One LED will light upIf the USB is connected

Step 3Step 3:Click the software icon in the bottom right corner of the screen and click the “Position calibration ”

Click the point by IR penNotice: The device will be OK When you click all the points by IR pen.

That is all !Just need 3 steps for the first time using !

REDS Interactive Whiteboard

You only need to do the Step 2 for next time.

The device can remember the positioning data

First time

Next time

REDS Interactive Whiteboard

Color

Thickness

Pen

Line

Ellipse

Windows/whiteboard

Windows/Note

Cut

Delete all

Erase

Function Menu

REDS Interactive Whiteboard

How to solve the problems in the course of using ?

C B A

Through the camera to judge whether the infrared pen is ok

The device can be disturbed by sunlight, flames, incandescent light, because they contain bands of infrared light the device need. Please avoid such interference as following:

Through the observation of A B C LED light is equipment judgment

REDS Interactive WhiteboardNO

. Problems Reasons Solutions

5.1 All the lights are not bright

1: USB cable not connected to the computer2: USB cable not connected to the equipment3: Computer power off

1: Connect USB cable correctly2:Connect USB cable correctly3:Computer power on

5.2 Light C is off1 ： Signal pen failure2 ： Device and the driver does not match3 ： Projection area exceeds the device signal area4 ： Equipment failure

1 ： Refer to 5.92 ： Use the drive inside CD3 ： Adjust the position of receiver, refer to 2.44 ： Replace with new device

5.3 Light C flashes(IR pen does not work)

1:Disturbing signal within the working area like sunlight or other signal (Observe whether light C keep flashing)

1: Get window curtains or exclude disturbing signal, refer to 3.2

5.4 Light C flashes(IR pen does not work)

1: low battery2:Curve set too small3: Working area too big4:Receiver and sender distance too far

1 ： Replace with new battery2 ： Set parameters larger3 ： Adjust the angle of receiver, refer to 2.44 ： Adjust the angle of receiver, refer to 2.4

5.5 In positioning setting, can not be located correctly

1 ： Refer to 5.2 and 5.3 1 ： Refer to 5.2 and 5.3

5.6 Sawtooth in writing 1 ： Refer to 5.4 1 ： Refer to 5.4

5.7Kept jitter mouse is adsorbed in a given region of the screen, or irregular jumps

1 ： Refer to 5.3 1 ： Refer to 5.3

5.8 Mouse position and click position offset

1:Fixed position relationship between the projection area and the receiver is moved 1: Reset the position

5.9 Pen fault

1 ： IR pen not light, battery input wrong2 ： Inside electronic component damaged3 ： The light us weak see from camera4 ： The back cover is not tightened, the pen shell and battery cover is not conductive

1 ： Input battery correctly2 ： Replace the IR pen3 ： Low battery, change new one4 ： Forced to tighten the back cover (limited to aluminum electronic pen)

REDS Interactive Whiteboard

Technical Support by TW Trade Technology, LLC.

Tel: +886 - 2 - 8522 7717Fax: +886 - 2 - 8522 7716