Installation Guide Product parts list Antenna Installation Head ...
INTRODUCTION INCLUDED PARTS INSTALLATION
1
材质: 105铜版纸 印刷: 单黑双面印刷 装订方式: 风琴折页 尺寸: 110*75mm 反面 05 2.Remove existing seat and lid . 3.Release the bolts on both side of the existing toilet seat. seat 06 Warning! Please place this bidet attachment at room temperature and do not storage it and its accessories in the freezing temperature environment under 0 degree Celsius. INTRODUCTION Thank you for purchasing DALMO bidet attachment. Please read these manual carefully and keep it for future reference INCLUDED PARTS Cold water inlet Seat(seat hook)coupling hole Water pressure control knob Body Bidet wash T adapter connector size7/8” 3.Metal Braided Hose (65cm/25.59 inch) Wrench Plumbers Tape Screwdriver Installation Tools You May Needed (not included) 1.Shut off water supply to toilet. Flush toilet to drain all water inside the tank. Water tank valve INSTALLATION DDB01S1/DDB01S2 Made in China Company:Shenzhen Woyi Trading Co., Ltd. Web: www.dalmo.com Facebook: www.facebook.com/dalmo.us E-mail: [email protected] ADD:6ceng 603, Gongye Dasha, Xinwu Cun, Zhuguang Lu, Taoyuan Jiedao, Nanshan Qu,Shen Zhen, CHINA 1.Bidet Bidet Attachment User Manual 09 7.Cold Water Installation Connect supplied T adapter to fill valve underneath of toilet water tank and connect 65cm/25.59 inch metal braided hose between T adapter and cold water inlet of bidet T adapter connector Water tank 65cm/25.59 inch metal braided hose 10 11 13 12 Water valve Water tank Toilet Seat Flexible hose HELPFUL TIP: Over tightening can cause damage to the threads and result in water leakage. Use only hand pressure first and check for any leakage. Turn only less than quarter turn at a time making sure there is no leakage. water tank HOW TO USE Trouble Shooting If the nozzles are clogged for some reason, please simply try to move them up and down manually for few times. Single nozzle system Bidet wash 1.Knob 1: turn left to adjust water pressure, the more we turn it, the bigger the water flow 2. knob 2: rotate according to indicator on the knob for function selection Knob 1 Knob 2 T adapter connector Function selection knob rubber non-slip mat (2) Bumper(3) Adjustable mounting brackets(2) 08 6.Install bidet on toilet Place bidet on toilet, and adjust its position, ensure the nozzles on the middle and won't stucked when spraying. And then adjust the mounting brackets angle, make them fit for the toilet seat installation holes on the toilet, and then mount toilet seat back and tighten Seat 07 Toilet Bowl After the installation. If there’s gap between toilet seat and bowl like shows, let me help you! 1 Select appropriate places for us,and clean them 2 Tear off the film on my back 3 Stick me on the selected place, and push me. Users Guide of Bumper 14 4.Install the rubber non-slip mats to the bottom of the the bidet 5 . place the adjustable mounting brackets into the bidet seat coupling holes
Transcript of INTRODUCTION INCLUDED PARTS INSTALLATION
材质: 105铜版纸 印刷: 单黑双面印刷 装订方式: 风琴折页 尺寸: 110*75mm
反面
05
2.Remove existing seat and lid .
3.Release the bolts on both side of the existing toilet seat.
seat
06
Warning! Please place this bidet attachment at room temperature anddo not storage it and its accessories in the freezing temperatureenvironment under 0 degree Celsius.
INTRODUCTION
Thank you for purchasing DALMO bidet attachment. Please read thesemanual carefully and keep it for future reference
INCLUDED PARTS
Cold water inlet Seat(seat hook)coupling hole
Water pressure control knob
Body Bidet wash
T adapter connector size7/8”
3.Metal Braided Hose (65cm/25.59 inch)
Wrench Plumbers Tape Screwdriver
Installation Tools You May Needed (not included)
1.Shut off water supply to toilet. Flush toilet to drain all water inside the tank.
Water tank
valve
INSTALLATION
DDB01S1/DDB01S2
Made in China
Company:Shenzhen Woyi Trading Co., Ltd.Web: www.dalmo.comFacebook: www.facebook.com/dalmo.usE-mail: [email protected]:6ceng 603, Gongye Dasha, Xinwu Cun, Zhuguang Lu, Taoyuan Jiedao, Nanshan Qu,Shen Zhen, CHINA
1.Bidet
Bidet Attachment
User Manual
09
7.Cold Water Installation
Connect supplied T adapter to fill valve underneath of toilet water tank and
connect 65cm/25.59 inch metal braided hose between T adapter and cold water
inlet of bidet
T adapter connector
Water tank
65cm/25.59 inch metal braided hose
10 11 1312
Water valve
Water tank
Toilet Seat
Flexible hose
HELPFUL TIP:
Over tightening can cause damage
to the threads and result in water leakage.
Use only hand pressure first and check for any leakage.
Turn only less than quarter turn at a time making sure there is no leakage.
water tank
HOW TO USE Trouble ShootingIf the nozzles are clogged for some reason, please simply try to move them
up and down manually for few times.
Single nozzle system
Bidet wash
1.Knob 1: turn left to adjust water pressure, the more we turn it, the bigger
the water flow
2. knob 2: rotate according to indicator on the knob for function selection
Knob 1
Knob 2
T adapter connector
Function selection knob
rubber non-slipmat (2)
Bumper(3)Adjustablemounting brackets(2)
08
6.Install bidet on toilet
Place bidet on toilet, and adjust its position, ensure the nozzles on the middle
and won't stucked when spraying. And then adjust the mounting brackets angle,
make them fit for the toilet seat installation holes on the toilet, and then mount
toilet seat back and tighten Seat
07
Toilet Bowl
After the installation. If there’s gap between toilet seat and bowl like shows, let me help you!
1 Select appropriate placesfor us,and clean them
2 Tear off the film on my back 3 Stick me on the selectedplace, and push me.
Users Guide of Bumper
14
4.Install the rubber non-slip mats to the bottom of the the bidet
5 . place the adjustable mounting brackets into the bidet seat coupling holes
