Intro to RobotC

Developed in collaboration with

Introduction to Programming

ROBOTC Start Page

Displays the latest ROBOTC news, version of ROBOTC, and ROBOTC Resources

Platform Type

Allows you to toggle ROBOTC’s programming mode between the Natural Language (VEX Cortex), VEX Cortex, and the VEX PIC; enables features and commands specifically for the selected system

Select Innovation First, then Natural Language

VEX Cortex Download Method

Allows you to specify:

1. How programs are downloaded

2. Whether the Cortex looks for a VEXnet connection when it starts up

Sample Programs•To generate the Natural Language Function Library, go to File, Open Sample Programs, PLTW, PLTWtemplate

Function Library

The Function Library will be populated by all of the Natural Language commands. These can be drag-and-dropped into your program.

Place you cursor over the commands for more details about each one.

ROBOT Motion

• Commands that cause the entire robot to perform a behavior

Setup

• Allows you to specify what type of robot configuration you have from pre-specified models (RECBOT, Swervebot)

Movement

• Commands that allow you to control individual motors / servos

Special

• Commands that control the more unique VEX Hardware – LED’s and Flashlights

Until

• Commands that allow you to create behaviors where the robot acts “until” a certain event. For example,– Button Press– Potentiometer Value

Wait

• Commands that wait for an elapsed amount of time in seconds or milliseconds

ROBOTC Help

Includes in-depth explanations about the ROBOTC interface, commands, debugger, ect

Help Documentation

Additional detail about the Natural Language commands can be found in the ROBOTC Help under “Natural Language Functions”

Motors and Sensors Setup Menu

Allows you to configure and name all of the motors and sensors connected to your Cortex.

Motors and Sensors Setup Menu

The information in ROBOTC Motors and Sensors Setup should match the schematic on your project lab sheets.

Comments

• Comments are used to make notes for the human programmers

• // Single line comment – everything after “//” is ignored by the ROBOTC compiler

Comments

• /* Multi-line comment*/ - everything between the “/*” and “*/” symbols is ignored by the ROBOTC compiler

Let’s start a ROBOTC Program

ROBOTC Practice Program• Open a Sample Program

Go to File > Open Sample Program > PLTW>PLTWtemplate

ROBOTC Practice Program

1. Rename file and save to student directory

2. Complete heading information

3. Describe task

Pseudocode

• Pseudocode is a shorthand notation for programming which uses– informal programming structures (if touch1 is pressed…)– verbal descriptions of code (move forward, stop)

• Emphasis is placed on expressing the behavior or outcome of each portion of code rather than on correct syntax (it should be reasonable, though).

• Your lines of Pseudocode should also be listed in the same order as they will appear in the ROBOTC Program


• Write pseudocode turn the motor on for 3 seconds at full power, then off for 10 seconds. Then back on for 3 seconds at ½ speed, off for 2 seconds and reverse at ½ power for 3 seconds.


• Complete Motors and Sensors Setup

• Notice the #pragma statements that are automatically generated

ROBOTC Practice Program• Convert pseudocode to program code using the

Natural Language Function Library to drag and drop commands.

All commands belonging to task main must be in-between these curly braces

Defines the “main task” of the robot. Every program must contain a task main


1. Save Program

2.Connect the Cortex to the Computer (via USB)

3.Turn on the Cortex

4.Go to Robot > Compile and Download Program (f5)

5.Run the program – Observe the motor turn on and off and reverse.


Edit the program to start when a pushbutton switch is pressed and stop when a limit switch is pressed.


You may notice warnings or errors.•Make sure you spell motor and sensor names exactly as defined in Motors and Sensors setup.•A ; is needed at the end of each line of code.•Don’t forget every open parenthesis needs a closing parenthesis.•What is wrong with line 31?

ROBOTC Debugger

• The ROBOTC Debugger allows you to view and manipulate all of the values of your motors, sensors, timers, and variables.

• Now that we’ve configured the motors and sensors, let’s view their values using the ROBOTC Debugger.

ROBOTC Debugger

• Make sure your robot is connected to your computer and turned on, and download the program.

• When the Program Debug Window appears, press the Start button and make sure the Refresh Rate is set to Continuous.

ROBOTC Debugger

• Open the Sensor Debug window by going to Robot > Debug Windows > Sensors

Sensor Debug Window

• The Sensor Debug window will appear, and display all of the values of the configured sensors.

0 = on, 1 = off

0 = released, 1 = pressed


• Modify your program so that an LED comes on when the motor is on, and goes off when the motor is off.

• Where in the function library are the LED commands?

• What do you type into the (digitalPort)?

• Compile and Download the program.

• Test

Resources• ROBOTC.net: http://www.robotc.net/

–The ROBOTC Forum: http://www.robotc.net/forums/

• VEX Cortex Video Trainer

–http://www.education.rec.ri.cmu.edu/products/teaching_robotc_cortex/index.html

• The FIRE Project:

–http://www.education.rec.ri.cmu.edu/fire/competitions/best/

• Robotics Academy

–http://www.education.rec.ri.cmu.edu/content/vex/index.htm

References

Carnegie Mellon Robotics Academy (2011). VEX Cortex Video Trainer. Retrieved from http://www.education.rec.ri.cmu.edu/products/teaching_robotc_cortex/index.html

Intro to RobotC

Education

Transcript of Intro to RobotC