15 -16 December 2017, Hotel Crowne Plaza, Mayur Vihar, New Delhi

“Power & Energy” -Operation, Maintenance, Inspection & Corrosion ControlOMIC Power 2017International Conference & Exhibition

Mob. no.: +91 99719 43010; Off. no.: 011- 46545757E-mail: power@omic.co.in; contactpower@omic.co.inWebsites: www.omic.co.in/omic-power-2017

Media Partner

Gold Partner

Where other material fails,Earthing specialists rely

upon Marconite.

Knowledge Partner

ISNT Delhi Chapter

Conference

Delegate Registration:Kindly send your nomination/ participation details to:power@omic.co.in; contactpower@omic.co.in

Category FeeSpeaker (Primary/Presenting) Rs. 15,000/- (USD 300)Delegate/Co-Speaker Rs. 18,000/- (USD 400)Student/ Spouses Rs. 5,000/- (USD 100)

18% GST will be applicable as extra.Corporate discount10% additional discount if 3 & above nos. of del. participated from same organization.15% additional discount if 6 & above nos. of del. participated from same organization.

Welcome you all to OMIC Power

Submit Abstracts for Oral / Poster Papers Presentation:Technical Committee of OMIC Power 2017 invites authors to submit technical papers on specified technical topics for Oral Presentation or Poster Paper during conference. Authors are requested to submit abstracts not exceeding 300 words and as per the guidelines.Please send your abstract to: power@omic.co.in; contactpower@omic.co.in

Power is one of the most critical components of infrastructure crucial for the economic growth and welfare of nations. The existence and development of adequate infrastructure is essential for sustained growth of the Indian economy. India’s power sector is one of the most diversified in the world. Sources of power generation range from conventional sources such as coal, lignite, natural gas, oil, hydro and nuclear power to viable non-conventional sources such as wind, solar, and agricultural and domestic waste. In order to meet the increasing demand for electricity in the country, massive addition to the installed generating capacity is required.

Operation & Maintenance (O&M) contracts cover all aspects and activities necessary to run your power plant in a safe and most economical manner. The key objective is to continuously optimizing the operations with an aim to enhance availability, output, efficiency of power plant along with power plant life. A scientific program of preventive maintenance and periodic repair ensures that the plant remains in peak condition. The initiative of OMIC Power 2017 will provide an ideal platform for experts and technocrats to share ideas on various technical discussions related to smooth & optimum operation, advanced maintenance techniques, NDT & Inspection Techniques, Corrosion Damage Mechanisms & its control etc. Your involvement at this premier event is essential to accomplish our mission “Maintaining Safety & reliability of your Assets along with Operational Excellence”.

OMIC Power Technical Sessions:Session 1 Session 5Power & Energy- Overview, Develop-ments, Difficulties and Solutions

Major Equipment’s in Power Industry (Cooling Tower & Boiler, Water Treat-ment, Exchangers, Turbines, Genera-tors etc.)

Session 2 Session 6Operation & Maintenance in Con-ventional Power Plants (Thermal Pow-er, Hydro Power & Nuclear Power etc)

Inspection & NDT activities in Power & Energy

Session 3 Session 7Operation & Maintenance in Renew-al Energy (Solar Power, Wind Energy etc)

Corrosion Control & Management in Power Plant

Session 4 Session 8Non-Conventional Power (Geo-thermal Energy, Hydrogen Ener-gy, Tidal Energy, Wave Energy, Bio-mass Energy etc)

Reliability & Asset Integrity in Pow-er & Energy (RCM, Plant Integrity, Risk Based Inspection), Energy Audit & Survey

Overview of Power & Energy Industry Overview of the Sector, Developments, Growth & Requirement of Power with Industrialization, Difficulties and Solutions, Combined Heat & Power (CHP) or co-generation Power Loss in Transportation (resistance), Carbon Capture & Storage (CCS), Waste Heat Recovery.Thermal PowerMaintenance of Steam Generator & Auxiliaries, Plant start-up, Station management services, Coal/ Gas based Plant, Combined Cycle plants, Development of O&M Management Systems & computerization, Equipment Repairs, Laboratory tests & field tests, Performance Analysis and Optimization, Fuel Management, PG test/capacity test, Break down maintenance services, Energy analysis of the steam cycle, Reheat cycle, Regenerative cycle. Maintenance of boiler, Turbines, critical equipment etcHydro PowerSystem upgrades and improvements, Operational optimization, Inspection of Turbine, bearing/ Gearbox, Drive belt & Coupling etc. Sensor replacement, Controller optimization, Internal (endoscopic) inspections of turbines and gearboxes. Preventive Maintenance of Hydro Turbine, Generator, Transformers, Hydro-mechanical Equipment, Civil structure (concrete) etc.Nuclear PowerNuclear reactor, Steam Turbines, valves, coolant pipe, reduction of O&M costs, safety & performance, extend operation period, radiation detection systems for personnel, health physics and plant processes; radiation sensitive cameras, area monitors and telemetry or safety systems for reactor containment monitoring and controlSolar EnergyPV module, Inverter, Concentrated solar power (CSP), Hybrid systems, Grid integration, Energy payback time (EPBT), life-cycle analysis, Effective data interpretation, PV system monitoring systems, Trending and Analytics for continuous improvement, Electrical sub-systems like Inverter, wiring etc, Civil and Structural sub-systems, Performance analysis.Wind EnergyWind Turbines, Blades, Rotor, Shaft, Gear box, Transformers, Generator, Tower, Transmission Lines etc, Cost modeling and efficiency identification, Interfacing with community, grid operator, surface and structural repairs, Leading edge protection, low noise serrations and aero enhancements, optimized blade/bearing exchange, remote monitoring and troubleshooting, SCADA – upgrade, customize.Non-conventional EnergyGeothermal Energy, Hydrogen Energy, Tidal Energy, Wave Energy, Bio-mass Energy

Technical Agenda & Topics to be covered: Inspection & MaintenanceReal-time plant monitoring and control, Preventive Maintenance (PM) & Inspection, Corrective Maintenance(CM) or breakdown Maintenance(BM), Condition-Based Monitoring(CBM), Circuit testing, IV curve tracing, Thermal imaging, Data acquisition system check, Warranty management, Spare parts and inventory management, Minimize Downtime, Reduce Equipment Failures, Protect Asset Value, Safety focus, advanced sensors and analytics, Plant Life management (PLiM) program.Corrosion Control & ManagementCommon Types of Corrosion, Oxide corrosion, Galvanic corrosion, Erosion, High temperature corrosion, Oil-ash corrosion, Stress corrosion, fatigue corrosion etc. safety hazards due to hot steam, gas, ash, or radioactive materials from a leaky component or welding failure. Cathodic protection of buried storage tanks & underground piping systems. Exterior surface coatings, application of internal coating, optimum metallurgy for long design life, weather-resistant solar modules, plasma coating, Galvanization etc, Corrosion protection of offshore wind turbines.Cooling Water TreatmentDiagnostics for water chemistry, cooling tower, heat exchanger/ condenser, water treatment, chemical treatments.Asset Integrity, Energy AuditReliability & Asset Integrity in Power & Energy (RCM, Plant Integrity, Risk Based Inspection), Energy Audit & Survey, Energy efficiency.

Conference SouvenirAIM E-magazine (Conference Souvenir) will be published with details of participating companies, abstracts (presented during the Seminar), photographs etc. The magazine will feature advertisements from the industry and is of tremendous publicity & business value. The e-copy of the magazine is going to have a significant number of free circulation (more than 92,000 worldwide) covering almost all the industry, service providers, contractors, supplier as well as end users. Advertisement material should be High Resolution 300 dpi; Color Mode-CMYK; Format- PDF, TIFF, JPEG. The advertisement charges are as follows:

Advertisement Charges FeeOutside Back Cover Page Rs. 15,000/- (USD 300)Inside Front/ Back Cover Page Rs. 12,000/- (USD 240)Double Spread Ad (2 page) Rs. 12,000/- (USD 240)Full Page (Colour) Rs. 8,000/- (USD 160)Half Page (Colour) Rs. 5,000/- (USD 100)

18% GST will be applicable as extra. Fees mentioned in dollar ($) applicable for Overseas Compnies.

Supports & Branding:

Category Platinum Gold Silver

Benefits at a Glance 3,00,000/- (USD 6000)

2,00,000/- (USD 4000)

1,20,000/- (USD 2400)

Complimentary exhibition booth 8 sq. m (4 X 2)

8 sq. m (4X 2)

6 sq. m (3 X 2)

Complimentary no of delegates 8 6 4Special Technical Representation of the Products/ Services (15 min.) of your company

Yes Yes -

Representative at the Dias (Session Chair/ Panelist)

Yes (Both Days) Yes Yes

Sharing of Participant Contact List Yes Yes Yes1 Page Advt. & 1 Page Company Profile in Souvenir Yes Yes Yes

Wide publicity of logo and banner Yes Yes YesDisplay of Company logo in conference website Yes Yes Yes

Memento Presented Yes Yes Yes18% GST will be applicable as extra.

Exhibition

Stall Options 6 sq. m (3 x 2) 4 sq. m (2x2) Table Top

Benefits at a Glance 80,000/- (USD 1600)

60,000/- (USD 1200)

35,000/- (USD 700)

Complimentary no of delegates 2 2 1Company Advt. in Souvenir 1 Page 1 Page 1PageLogo in Back Stage Banner Yes Yes YesDisplay of company logo in Website Yes Yes Yes

Memento will be presented Yes Yes -18% GST will be applicable as extra.

Stalls & Exhibition Charges:The exhibitions shall provide an opportunity to promote a meaningful interaction between end users and product/ service providers. The organizers will provide a well-furnished modern exhibition facility at the venue which can easily be accessed by the participants. This exhibition will be open to all the delegates, visitors and invitees from industry, research and academic institutions during the conference. The exhibitors will be entitled for the below facilities:

For advertisement technical specifications are:Full page A4: Without bleed: 7.75 in(w) x 11 in(h) With bleed: 8.25 (w) X 11.5 (h)

Half Page: Without bleed: 7.75 in(w) x 5.25 in(h)With bleed: 8.25(w) x 5.75(h)

Companies Participated in Past Events

Terms & Conditions:All bookings carry a cancellation charges.

Substitutions of delegates prior to the event date may be allowed subject to management’s discretion.For any reason, if Organizers decides to cancel or postpone this event; Organizers will not be responsible for any loss incurred by Client/ Participant.

The conference fee will not be refunded and shall be adjusted with future event fee.Hotel Location of the event may be changed depends on the no of participants without any intimation.

Content of the event program can be changed without any intimation.

Address: Somdatt Chambers, Bhikaji Cama Place, New Delhi- 110066, IndiaMob. no.: +91 99719 43010; Off. no.: 011-46545757

E-mail: power@omic.co.in; contactpower@omic.co.inWebsites: http://omic.co.in/omic-power-2017