internal DMM assembly.pdf
-
Upload
nakaruru55 -
Category
Documents
-
view
215 -
download
0
Transcript of internal DMM assembly.pdf
-
7/27/2019 internal DMM assembly.pdf
1/4
1
Ribbon Cable
Agilen t 34970A/34972A Opt ion 001
In t erna l DMM Assembly
I nstal l at i on I nstru cti ons for 34970-80010 Retr ofi t K it
1 Disconnect the power cord.
2 Remove the outer cover from the 34970A/34972A.
To remove the instru ments cover , follow the procedures
shown in chapter 6 of t he 34970A/ 34972A Ser vice Gui de.
3 Connect the internal DMM ribbon cable to themain circuit board.
Connect t he loose end of th e gr ey ribbon cable to connector
J202 on the ma in circuit boa rd . Press down firmly on t he
ribbon cable connector a nd secure th e cable in place with the
locking clips .
Snap Locking Clipsover the top of theconnector to securethe Ribbon Cable
-
7/27/2019 internal DMM assembly.pdf
2/4
2
4 Install the internal DMM circuit board into the chassis.
P osition the interna l D MM circuit boa rd inside th e inst rum entcha ss is by t i l t ing i t a t a n angle a s shown below. Be sure t o position
t he cir cu it board over the tabs in the chassis a s show n. Then,
low er the a ssembly into th e cha ssis unt il it is para l lel with the
34970A/34972A circuit boar d.
5 Lock the internal DMM circuit board in place.
Slide the in terna l D MM circuit boa rd t o t he left (towa rd the rear of
t he in s t r umen t )unt il it locks in place. You will hear a click w hen it is
properly locked in pla ce.
Make sure that shield islocked in place behindthis tab
-
7/27/2019 internal DMM assembly.pdf
3/4
3
6 Twist the internal DMM input cable.
Tw ist the interna l D MM input cable (labeled P101) a t l eas t one ful lturnbefore plugging it into the backplane connector. If you do not t wist t h e
ca ble a s show n, specificat ions will be c ompromised .
7 Insert theDMM input cable into the backplaneconnector.
Insert the interna l DMM input cable into the ba ckpla ne conn ect or a s
shown. P ress firmly t o ensure a good electrical connect ion .
8 Enable the internal DMM.
After insta lling the interna l D MM assembly, you must enable i t for
opera t ion. From th e front -pa nel, select t he DMM ENABLED choice fr
omthe Ut i l i tymenu. From the remote interfa ce, use the INST:DMMcomma nd.
-
7/27/2019 internal DMM assembly.pdf
4/4
4
Opt 001
9 Modify the Labeling on the Rear Panel.
If you origina lly ordered th e inst rument withoutthe in terna lDMM, a solid bla ck circle should be visible above the rear -panel
Opt . 001 label. After insta lling the interna l D MM retrofit kit ,
be sure t o draw an X through t he bla ck circle using a permanent
marker a s shown below.
10 Replace the outer cover on the Agilent34970A/34972A.
To replace the cover, follow the procedures sh own in chapter 6 of t he
34970A/ 34972A Ser vice Gui de.
Ca l i b r a t i o n I nf or m a t i on
The in ternal DMM w as ca librat ed before it w a s shipped from t he
fa ct ory (a ca libra tion certificat e is included). H ow ever, a ft er installingthe in t er na l DMM, you will w a n t t o ma ke sure tha t you run theZeroAdjustmentprocedure a s outlined in chapter 4 in t he
34970A/ 34972A Ser vice Gui de. The in ternal DMM is g uaranteed
t o meet the inst rumen t s 1-yea r accuracy specifica t ions .
Agilent Technologies, Inc. 1998-2010Printed in Malaysia E0210
Edition 1 February 2010
Opt 001
Internal DMM
is NOT installed.
Internal DMM
is installed.
*34970-90053*34970-90053