Instruction Sheet NETCONNECT® Undercarpet 408-8843 ... filePeel back the release paper on the tape....
3
Figure 1 This instruction sheet provides installation procedures for NETCONNECT Undercarpet Multimedia Dual Data Kit 1479542–1. To obtain information on NETCONNECT products, call Product Information at the number at the bottom of this page, or visit the NETCONNECT website at Reason for revision is given in Section 3, REVISION SUMMARY. The NETCONNECT Undercarpet Multimedia Dual Data Kit consists of a cover, a baseplate, and four oval–head screws to use when mounting the cover. Foam tape is attacked to the underside of the baseplate. This kit can be used for undercarpet applications and underfloor duct systems. The baseplate can be mounted using one of two methods (mounting hardware/foam tape). If using mounting hardware (customer supplied), proceed as follows: 1. Center baseplate on reference line and mark hole locations. 2. Drill holes to accept mounting hardware. 3. Vacuum debris. Insert hardware. Figure 2 If using foam tape, proceed as follows: 1. Vacuum debris. 2. Peel back the release paper on the tape. 3. Position baseplate in desired location. Press firmly to secure. Figure 3 NETCONNECT® Undercarpet Multimedia Dual Data Kit 1479542-1 Instruction Sheet 408-8843 FEB 2017 REV B To obtain information CommScope® products, visit our website at http://www.commscope.com/SupportCenter/TechnicalSupport.aspx ©2017 CommScope, Inc. All Rights Reserved This product is covered by one or more U.S. patents or their foreign equivalents. For patents, see www.commscope.com/ProductPatent/ProducePatent.aspx
Transcript of Instruction Sheet NETCONNECT® Undercarpet 408-8843 ... filePeel back the release paper on the tape....
Figure 1
This instruction sheet provides installation proceduresfor NETCONNECT Undercarpet Multimedia DualData Kit 1479542–1.
To obtain information on NETCONNECT products,call Product Information at the number at the bottomof this page, or visit the NETCONNECT website at
Reason for revision is given in Section 3, REVISIONSUMMARY.
The NETCONNECT Undercarpet Multimedia DualData Kit consists of a cover, a baseplate, and fouroval–head screws to use when mounting the cover.Foam tape is attacked to the underside of the
baseplate. This kit can be used for undercarpetapplications and underfloor duct systems.
The baseplate can be mounted using one of twomethods (mounting hardware/foam tape).
If using mounting hardware (customer supplied),proceed as follows:
1. Center baseplate on reference line and markhole locations.2. Drill holes to accept mounting hardware.3. Vacuum debris. Insert hardware.
Figure 2
If using foam tape, proceed as follows:
1. Vacuum debris.2. Peel back the release paper on the tape.3. Position baseplate in desired location. Pressfirmly to secure.
Figure 3
NETCONNECT® Undercarpet Multimedia Dual DataKit 1479542-1
Instruction Sheet 408-8843 FEB 2017 REV B
To obtain information CommScope® products, visit our website athttp://www.commscope.com/SupportCenter/TechnicalSupport.aspx
©2017 CommScope, Inc. All Rights Reserved
This product is covered by one or more U.S.patents or their foreign equivalents. For patents, seewww.commscope.com/ProductPatent/ProducePatent.aspx
Figure 4
Proceed as follows:
1. After wiring is complete, snap the single portoutlet into the bottom of the cover. See Figure 5.
Figure 5
2. Attach the outlet to the cover by inserting twoNo. 2 screws into two diagonal posts on thehousing. See Figure 6.
Figure 6
3. Align faceplate and press on from the FRONT ofthe housing. See Figure 7.
Figure 7
B
Figure 8
Proceed as follows:
1. After wiring is complete for jack applications,snap the modular jack into the appropriate openingin the baseplate. Refer to Figure 9.
Figure 9
2. Terminate SVGA connector according to colorcode on connecting blocks. Assemble connector tobaseplate using hex standoff screws. SeeFigure 10.
Figure 10
1. Align the screw holes in the cover with the postson the baseplate.
2. Secure by inserting the oval–head screws.
3. Tighten screws.
Figure 11
Updated document to corporate requirementsAdded NOTE to Paragraph 4.2
B
Rebranded to CommScope
