INSTALLATION VERSION 1 INSTRUCTIONS 2017 MDX JUN 2016

16
© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-24 (1606) 1 of 16 08V67-TZ5-2C00-90 VERSION 1 Publications No. Issue Date INSTALLATION INSTRUCTIONS Accessory Application FRONT AND REAR PARKING SENSORS 2017 MDX JUN 2016 PARTS LIST Parking Sensor Attachment Kit P/N 08V67-TZ5-200C Control unit Front bumper harness Rear bumper harness Control unit bracket Switch 4 Retainers Self-tapping screw 2 Alcohol swabs User’s Information Manual Parking Sensor Kit NOTE: Refer to the Parts Information Bulletin (PIB) for the proper color sensors. 2 Sensors A (Body color) 2 Sensors B (Body color) 2 Sensors C Sensor D

Transcript of INSTALLATION VERSION 1 INSTRUCTIONS 2017 MDX JUN 2016

© 2016 American Honda Motor Co., Inc. – All Rights Re

VERSION 1Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

FRONT AND REARPARKING SENSORS

served. BII03445-24 (160

2017 MDX

6) 0

Issue Date

JUN 2016

PARTS LISTParking Sensor Attachment KitP/N 08V67-TZ5-200C

Control unit

Front bumper harness

Rear bumper harness

Control unit bracket

Switch

4 Retainers

Self-tapping screw

2 Alcohol swabs

User’s Information Manual

Parking Sensor KitNOTE: Refer to the Parts Information Bulletin (PIB) for the proper color sensors.

2 Sensors A (Body color)

2 Sensors B (Body color)

2 Sensors C

Sensor D

1 of 168V67-TZ5-2C00-90

Sensor E

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriverSmall flat-tip screwdriver8 mm, 10 mm, and 13 mm Open end wrenchesRatchet10 mm SocketPushpinDrill3 mm, 6 mm, and 8.5 mm Drill bitsFileMasking tapeShop towelBlanketEye protection (face shield, safety goggles, etc.)The following tools are available through the Acura Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)• Plastic Trim Tool (T/N SILTRIMTL10)• 16 mm Punch Tool (T/N 07AAH-TZ5A100)

2 of 16 BII03445-2

Illustration of the Parking Sensors Installed on the Vehicle

QEN0301AJ

SWITCHCONTROL UNIT

SENSOR C

SENSOR E

FRONT BUMPER HARNESS

SENSOR DSENSOR C

2 SENSORS B

2 SENSORS A

REAR BUMPER HARNESS

INSTALLATION

Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

Removing the Vehicle Parts

1. Disconnect the negative cable from the battery:• Wrap a shop towel around the hood latch.

QE03001BJ

HOOD LATCH(Wrap with a shop towel.)

• Remove the front bulkhead cover.

QE03002BJ

FRONT BULKHEAD COVER

11 CLIPS

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

• Remove the air intake tube.• Disconnect the negative cable from the battery.

QE03003AJ

2 CLIPSAIR INTAKE TUBE

2. Remove the front bumper:• Apply masking tape as shown on each side.

QE03004AJMASKINGTAPE

FRONT BUMPER

HEADLIGHT

FRONT FENDER

4 (1606) 3 of 16

• Remove the air intake guide.

QE03005AJ

2 CLIPSAIR INTAKE GUIDE

• Remove the four self-tapping screws, the two push rivet clips, the four clips, the four short clips, the four washer-bolts, and the four flange bolts.

QE03006BJ

SELF-TAPPINGSCREW

4 CLIPS2 WASHER-BOLTS

4 FLANGE BOLTS

2 WASHER-BOLTS

2 SHORT CLIPS

2 SHORT CLIPS

PUSH RIVET CLIP

PUSH RIVET CLIP

2 SELF-TAPPING SCREWS

SELF-TAPPINGSCREW

4 of 16 BII03445-2

• Release the three retaining tabs on each side.

QE03007AJ

3 RETAINING TABS

FRONT BUMPER

• With the help of an assistant, release the four retaining tabs on each side.

QE03008BJ

4 RETAINING TABS

FRONT BUMPER

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

• With the help of an assistant, release the front bumper. Place the front bumper on the blanket to prevent damage.

QEN1301AT

FRONT BUMPER

6 CLIPS

3. Open the glove box by pushing the button (unlock with the built-in key). Remove the passenger’s dashboard side vent.

QE03014AJ

PASSENGER’S DASHBOARD SIDE VENT

3 CLIPS

GLOVE BOX

BUTTON

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

4. Remove the passenger’s dashboard trim panel. Close the glove box.

QE03015AJ

PASSENGER’S DASHBOARD TRIM PANEL

6 CLIPS

GLOVE BOX

5. Remove the dashboard center panel and unplug the vehicle connector.

QE03016AJ

10 CLIPS2 CLIPS

2 CLIPS

DASHBOARD CENTER PANEL

VEHICLE CONNECTOR

4 (1606) 5 of 16

6. Remove the passenger’s dashboard center lower cover.

QE03017AJ

5 CLIPS

PASSENGER’S DASHBOARD CENTER LOWER COVER

7. Pull away the door opening seal and remove the driver’s dashboard side lid.

QB02512AJ

4 CLIPS

DOOR OPENING SEAL(Pull away.)

DRIVER’S DASHBOARD SIDE LID

6 of 16 BII03445-2

8. Remove the driver’s dashboard side vent.

QF42701AJ

DRIVER’S DASHBOARD SIDE VENT 3 CLIPS

9. Remove the driver’s outer dashboard trim.

QF42702AJ

DRIVER’S OUTER DASHBOARD TRIM

3 CLIPS

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

10. Remove the driver’s dashboard lower cover.

QEN1302AT

10 CLIPS

DRIVER’S DASHBOARD LOWER COVER

2 SELF-TAPPING SCREWS

11. Remove the driver’s inner dashboard trim.

QE03018AJ

3 CLIPSDRIVER’S INNER DASHBOARD TRIM

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

12. Remove the bolt from the driver’s dashboard center lower cover.

QE03030BJ

BOLT

DRIVER’S DASHBOARD CENTER LOWER COVER

13. Remove the driver’s dashboard center lower cover and unplug the vehicle connector and temperature sensor.

QE03019CJ

6 CLIPS

DRIVER’S DASHBOARD CENTER LOWER COVER

TEMPERATURE SENSOR

TEMPERATURE SENSOR

2 RETAINING TABS

VEHICLE CONNECTOR

4 (1606) 7 of 16

14. Remove the center lower trim and unplug the vehicle connectors.

QE03034AJ

2 VEHICLE HARNESS CLIPS(if equipped)

2 TORX BOLTS(if equipped)Torque to 3.9 N·m(2.9 lb·ft)

4 SELF-TAPPING SCREWS

VEHICLE CONNECTORS(if equipped)

CENTERLOWER TRIM

15. Loosen the two bolts as shown. Remove the audio unit assembly and unplug the vehicle connectors.

QE03020AJ

AUDIO UNIT ASSEMBLY

4 SELF-TAPPING SCREWS

2 BOLTS(Loosen.)

BRACKET VEHICLE CONNECTORS

8 of 16 BII03445-2

16. Remove the dashboard center display lower visor.

QE03021BJ

2 CLIPS

2 SELF-TAPPING SCREWS

DASHBOARD CENTER DISPLAY LOWER VISOR

17. Remove the dashboard center display visor.

QE03022AJ

6 CLIPS

DASHBOARD CENTER DISPLAY VISOR

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

18. Remove the dashboard center display and unplug the vehicle connectors.

QE03023AJ

3 SELF-TAPPING SCREWS

DASHBOARD CENTER DISPLAY

VEHICLE CONNECTORS

19. Remove the rear bumper:• Apply masking tape as shown on each side.

QE01206AHREAR BUMPER

TAILLIGHTREAR FENDER

MASKINGTAPE

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

• Pull away the weatherstrip.

QE01207AH

WEATHERSTRIP(Pull away.)

REAR BUMPER

• Using a plastic trim tool, remove the two plug caps.

QE01208AH

2 PLUG CAPS

REAR BUMPER

8 RETAINING TABS

PLASTIC TRIM TOOL

2 PLUG CAPS

4 (1606) 9 of 16

• Remove the four bolts and two clips.

QE01209AH

REAR BUMPER

4 BOLTS

2 CLIPS

• Remove the five self-tapping screws on each side.

QE01210AH

REAR BUMPER

10 SELF-TAPPING SCREWS

REAR BUMPER

10 of 16 BII03445-2

• Release the eight retaining tabs on each side.

QE01211AH

REAR BUMPER

16 RETAINING TABS

REAR BUMPER

• With the help of an assistant, remove the rear bumper. Place the rear bumper on a blanket to prevent damage.

QE01212AHREAR BUMPER

4 RETAINING TABS

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

Installing the Parking Sensors

20. Using a pushpin, pierce the four scribe marks onto the rear bumper as shown.

QEN0302BJ

REAR BUMPER(inside)

4 MARKS

4 SCRIBE MARKS

REAR BUMPER

PUSHPIN(Pierce perpendicular.)

PUSHPIN

21. While wearing eye protection, drill the four pierced marks to 8.5 mm from the inside of the bumper.• First drill with a 3 mm drill bit, then drill with a 6

mm drill bit, and finish with an 8.5 mm drill bit.

QEN1304AT

REAR BUMPER(inside)

4 PIERCEDMARKS

DRILL(Drill perpendicular.)

REAR BUMPER

3 mm 6 mm 8.5 mm DRILL BIT

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

22. Using the 16 mm Punch Tool, punch out the four rear bumper holes as shown.

QEN0304CJ

OPEN END WRENCH

4 HOLES

REAR BUMPER(inside)

SECTION VIEW

REAR BUMPER

OUTSIDE INSIDE

16 mmPUNCH TOOL(MALE)

16 mmPUNCH TOOL(FEMALE)

16 mmPUNCH TOOL(MALE) 16 mm

PUNCH TOOL(FEMALE)

Clockwise. Counterclockwise.

4 (1606) 11 of 16

23. Using an alcohol swab, thoroughly clean the rear bumper where the retainers will attach.

QEN0305CJ

Align.

REAR BUMPER

REAR BUMPER(Clean with an alcohol swab.)

2 RETAINERS

2 RETAINERS

2 ADHESIVE BACKINGS

2 ADHESIVE BACKINGS

SCRIBE MARKS

SCRIBE MARKS

Align.

ALCOHOL SWAB

ALCOHOLSWAB

REAR BUMPER(Clean with an alcohol swab.)

ARROW

ARROW

24. Attach the four retainers to the rear bumper as shown.NOTE: Make sure the retainers are attached with the arrows in the proper direction.

12 of 16 BII03445-2

25. Attach the two sensors A and two sensors B to the four retainers as shown.

QEN0306AJ

REAR BUMPER

2 RETAINERS 2 RETAINERS4 RETAINING TABS

4 RETAINING TABS

2 SENSORS A 2 SENSORS B

26. Plug the four rear bumper harness 6-pin connectors into the two sensors A and the two sensors B.

QEN0307AJ

REAR BUMPER

2 SENSORS A 2 SENSORS B

REAR BUMPER HARNESS 3-PIN CONNECTOR

4 REAR BUMPER HARNESS 6-PIN CONNECTORS

REAR BUMPER HARNESS

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

27. Secure the four rear bumper harness clips to the two sensors A and two sensors B as shown.

QEN0308AJ

REAR BUMPER

4 REAR BUMPER HARNESS CLIPS

2 SENSORS A AND 2 SENSORS B

28. Secure the four rear bumper harness clips to the rear bumper as shown.

QEN0309AJ

REAR BUMPER

REAR BUMPER

4 REAR BUMPER HARNESS CLIPS

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

29. With the help of an assistant, remove the dummy connector from the vehicle 3-pin connector and plug the rear bumper harness 3-pin connector into the vehicle 3-pin connector. Install the rear bumper.

QEN0310AJ

REAR BUMPER

REAR BUMPER HARNESS 3-PIN CONNECTOR

VEHICLE 3-PIN CONNECTOR

DUMMY CONNECTOR(Do not reuse.)

30. Remove the four caps as shown.

QEN0311AJ

FRONT BUMPER(inside)

8 RETAINING TABS

4 CAPS(Do not reuse.)

4 (1606) 13 of 16

31. Attach two sensors C, one sensor D, and one sensor E to the front bumper as shown.

QEN0312AJ

FRONT BUMPER

2 RETAINING TABS

2 RETAINING TABS

SENSOR CSENSOR C

FRONT BUMPER FRONT BUMPER

2 RETAINING TABS

2 RETAINING TABS

SENSOR ESENSOR D

FRONT BUMPER

FRONT BUMPER

14 of 16 BII03445-2

32. Plug the four front bumper harness 6-pin connectors into sensor D, sensor E and both sensors C.

QEN0313AJ

SENSOR ESENSOR D

SENSOR CSENSOR C

FRONT BUMPER

FRONT BUMPER HARNESS 3-PIN CONNECTOR

4 FRONT BUMPER HARNESS 6-PIN CONNECTORS

FRONT BUMPER HARNESS

33. Secure the two front bumper harness clips to sensor D and sensor E as shown.

QEN0314AJ

FRONT BUMPER

2 FRONT BUMPER HARNESS CLIPS

SENSOR D AND SENSOR E

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.

34. Secure the six front bumper harness clips to the front bumper as shown.

QEN0315BJ

FRONT BUMPER

6 FRONT BUMPER HARNESS CLIPS

FRONT BUMPER

5 RETAINING TABS

35. With the help of an assistant, remove the dummy connector from the vehicle 3-pin connector and plug the front bumper harness 3-pin connector into the vehicle 3-pin connector. Reinstall the front bumper.

QEN0316AJ

FRONT BUMPER

FRONT BUMPER HARNESS 3-PIN CONNECTOR

VEHICLE 3-PIN CONNECTOR

DUMMY CONNECTOR(Do not reuse.)

© 2016 American Honda Motor Co., Inc. – All Rights Reserved. BII03445-2

36. Install the control unit bracket onto the control unit.

QEN0317AJ

CONTROL UNIT

CONTROL UNIT BRACKET

37. Locate the vehicle 16-pin connector taped to the vehicle harness. Remove the tape to free the vehicle 16-pin connector and plug the vehicle 16-pin connector into the control unit.

QEN0318AJ

VEHICLE 16-PIN CONNECTOR

CONTROL UNIT

TAPE(Remove.)

VEHICLE FRAME

SELF-TAPPING SCREW

38. Attach the control unit to the vehicle frame using the self-tapping screw.

4 (1606) 15 of 16

39. Remove the switch panel and unplug the vehicle connectors.

QEN1303AT

3 SELF-TAPPING SCREWS

SWITCH PANEL

VEHICLE CONNECTORS

40. Remove the lid. Install the switch into the switch panel as shown.

QEN0319AJSWITCH PANEL

SWITCH

LID(Discard.)

SWITCH

SWITCH

WITHOUT CMBS WITH CMBS

SWITCH POSITION

2 RETAINING TABS

16 of 16 BII03445-2

41. Locate the vehicle 6-pin connector (brown) taped to the vehicle harness. Remove the tape to free the vehicle 6-pin connector (brown) and plug the vehicle 6-pin connector (brown) to the switch.

QEN0320CJ

TAPE(Remove.)

VEHICLE 6-PINCONNECTOR(brown)

SWITCH

SWITCH PANEL

3 SELF-TAPPING SCREWS

42. Install the switch panel.

43. Check that all wire harnesses are routed properly and that all connectors are plugged in.

44. Install all removed parts except for the front bulkhead cover and the air intake tube.

45. Connect the negative cable to the battery.46. Install the front bulkhead cover and the air intake

tube.47. Press and hold the audio unit power button for 2

seconds to restore the audio and navi (if equipped) system functions.

48. Set the clock on vehicles without navigation.49. Check that the parking sensors work properly as

described in the User’s Information Manual.50. If necessary, restore the systems back to normal

operation as described in the service information.51. Attach the User’s Information Manual pages

(supplied in the kit) into the vehicle owner’s guide.

4 (1606) © 2016 American Honda Motor Co., Inc. – All Rights Reserved.