INSTALLATION VERSION 1 2019 CR-V …...RUNNING BOARDS P/N 08L33-TLA-100 2019 CR-V OCT 2018 PARTS...
12
Publications No. Issue Date INSTALLATION INSTRUCTIONS Accessory Application © 2018 American Honda Motor Co., Inc. – All Rights Reserved. AII10312-09 (1810) 1 of 12 08L33-TLA-1000-90 VERSION 1 RUNNING BOARDS P/N 08L33-TLA-100 2019 CR-V OCT 2018 PARTS LIST Left running board Right running board 2 Brackets A 2 Brackets B 2 Brackets C Left bracket D Right bracket D 48 Flange bolts (Black or silver) 2 Cushion tapes TOOLS AND SUPPLIES REQUIRED Ratchet 10 mm, 12 mm, and 17 mm Sockets Torque wrench Utility knife Ruler Felt-tip pen Shop towel Isopropyl alcohol The following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857. • Trim Tool Set (T/N SOJATP2014) • Plastic Trim Tool (T/N SILTRIMTL10)
Transcript of INSTALLATION VERSION 1 2019 CR-V …...RUNNING BOARDS P/N 08L33-TLA-100 2019 CR-V OCT 2018 PARTS...
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2018 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
RUNNING BOARDSP/N 08L33-TLA-100served. AII10312-09 (181
2019 CR-V
0) 0
Issue Date
OCT 2018
PARTS LISTLeft running board
Right running board
2 Brackets A
2 Brackets B
2 Brackets C
Left bracket D
Right bracket D
48 Flange bolts(Black or silver)
2 Cushion tapes
TOOLS AND SUPPLIES REQUIRED
Ratchet10 mm, 12 mm, and 17 mm SocketsTorque wrenchUtility knifeRulerFelt-tip penShop towelIsopropyl alcoholThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014) • Plastic Trim Tool (T/N SILTRIMTL10)
1 of 128L33-TLA-1000-90
Illustration of the Running Boards on the Vehicle
RIGHT RUNNING BOARD
LEFT RUNNING BOARD
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE:• Thoroughly clean the bottom of the body between the
front and rear wheels.• Be careful not to damage the body paint finish.• These instructions show the left side running board
being installed; the same procedure applies to installing the right running board.
2 of 12 AII10312-0
With the vehicle on a lift, locate the floor under cover. If the vehicle is equipped with the one-piece floor under cover, continue with step 1; if the vehicle is equipped with the separate floor under covers, go to step 6.
With one-piece floor under cover1. Remove the floor under cover.
8 WASHER-BOLTS FLOOR
UNDER COVER
17 LARGE CLIPS
CLIP
2 FLANGE NUTS
FRONT
9 (1810) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
If the vehicle is equipped with the insulator on the floor under cover, continue with step 2; otherwise, go to step 4.
With insulator2. Using a utility knife, cut the insulator on the floor
under cover and fold it into the inside of the insulator as shown. NOTE: Do not cut into the padding. Do not peel off the bonded part on the insulator.
INSULATOR
Do not peel off.
FLOOR UNDER COVER
INSULATOR
Cut.
Do not peel off.
Fold.
Do not peel off.
© 2018 American Honda Motor Co., Inc. – All Rights Reserved. AII10312-0
3. Using a utility knife, cut the insulator on the floor under cover and fold it into the inside of the insulator as shown.NOTE: Do not cut into the padding. Do not peel off the bonded part on the insulator.
INSULATOR
Cut.
Do not peel off.
INSULATOR
Fold.
FLOOR UNDER COVER
Do not peel off.
9 (1810) 3 of 12
4. Using a utility knife, cut off the floor under cover as shown.
SCRIBE LINES
Cut off.
Cut along the scribe lines.
Cut off.
Cut along the scribe lines.
Cut along the scribe lines.
Cut along the ends of each scribe line.
SCRIBE LINES
Cut along the ends of each scribe line.
SCRIBE LINES
Cut along the ends of each scribe line.
4 of 12 AII10312-0
5. Using a utility knife, cut off the floor under cover as shown. Go to step 16.
Cut off.
Cut along the scribe lines.
FLOOR UNDER COVER
Cut off.
Cut along the scribe lines.
Cut along the scribe lines.
SCRIBE LINES
Cut along the ends of each scribe line.
SCRIBE LINES
Cut along the ends of each scribe line.
Cut along the ends of each scribe line.
SCRIBE LINES
9 (1810) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
With separate floor under covers6. Remove the left floor under cover.
3 WASHER-BOLTS
LEFT FLOOR UNDER COVER
7 LARGE CLIPS2 CLIPS
FLANGE NUT
FRONT
7. Remove the right floor under cover.
2 WASHER-BOLTS
FLANGE NUT2 CLIPSRIGHT
FLOOR UNDER COVER
6 LARGE CLIPS
FRONT
© 2018 American Honda Motor Co., Inc. – All Rights Reserved. AII10312-0
If the vehicle is equipped with the insulator on the floor under covers, continue with step 8; otherwise, go to step 10.
With insulator8. Using a utility knife, cut the insulator on the left floor
under cover and fold it into the inside of the insulator as shown.NOTE: Do not cut into the padding. Do not peel off the bonded part on the insulator.
INSULATOR
Do not peel off.
INSULATOR
Fold.
LEFT FLOOR UNDER COVER
Cut.
Do not peel off.
9 (1810) 5 of 12
9. Using a utility knife, cut the insulator on the right floor under cover and fold it into the inside of the insulator as shown.NOTE: Do not cut into the padding. Do not peel off the bonded part on the insulator.
INSULATOR
Do not peel off.
INSULATOR
Fold.
RIGHT FLOOR UNDER COVER
Cut.
Do not peel off.
Do not peel off.
6 of 12 AII10312-0
10. Using a utility knife, cut off the right floor under cover as shown.
Cut off.
Cut along the scribe lines.
RIGHT FLOOR UNDER COVER
Cut off.
Cut along the scribe lines.
Cut along the scribe lines.
SCRIBE LINES
Cut along the ends of each scribe line.
SCRIBE LINES
Cut along the ends of each scribe line.
SCRIBE LINES
Cut along the ends of each scribe line.
9 (1810) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
11. Using a felt-tip pen, mark the left floor under cover as shown.
LEFT FLOOR UNDER COVER(inside)
SCRIBE LINES
FELT-TIP PEN
Mark along the ends of each scribe line.
LEFT FLOOR UNDER COVER
© 2018 American Honda Motor Co., Inc. – All Rights Reserved. AII10312-0
12. Using a utility knife, cut the left floor under cover as shown.
LEFT FLOOR UNDER COVER(inside)
LEFT FLOOR UNDER COVER
Cut along the mark.Cut along the scribe lines.
9 (1810) 7 of 12
13. Using a felt-tip pen, mark the left floor under cover as shown.
FELT-TIP PEN
LEFT FLOOR UNDER COVER(outside)
LEFT FLOOR UNDER COVER
Mark to the perpendicular line.
CURVE END
Make perpendicular line to the other end.
SLITMark to the curve end.
14. Using a utility knife, cut off the left floor under cover along the mark.NOTE: Be careful not to damage the inside parts.
Cut off.
LEFT FLOOR UNDER COVER(outside)
8 of 12 AII10312-0
15. Using a utility knife, cut off the left floor under cover as shown.
Cut along the scribe lines.
LEFT FLOOR UNDER COVER(inside)
Cut off.
Cut along the scribe lines.
SCRIBE LINES
Cut along the ends of each scribe line.
Cut off.
SCRIBE LINES
Cut along the ends of each scribe line.
9 (1810) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
16. Using isopropyl alcohol on a shop towel, thoroughly clean brackets B where the cushion tapes will attach.
SIDE VIEW
Clean with isopropyl alcohol.
SHORT LONG
BRACKET A BRACKET B
CURVE END
60 mm(2.36 in.)
CUSHION TAPE
BRACKET BCUSHION TAPE
CUSHION TAPE
BRACKET B(Use for the left side.)
Clean with isopropyl alcohol.
CURVE END
60 mm(2.36 in.)
CUSHION TAPE
BRACKET B
BRACKET B(Use for the right side.)
17. Attach one cushion tape to each bracket B as shown. Make sure to attach the cushion tapes in the correct position and orientation.
© 2018 American Honda Motor Co., Inc. – All Rights Reserved. AII10312-0
18. Loosely secure bracket B to the vehicle panel with four flange bolts.NOTE: If there are black and silver flange bolts in the kit, use the silver flange bolts.
2 FLANGE BOLTS(Use the silver flange bolts if included in the kit.)(Loosely secure.)
BRACKET BVEHICLE PANEL
2 FLANGE BOLTS(Use the silver flange bolts if included in the kit.)22 N·m (16 lb·ft)
FRONT
CUSHION TAPE(Make sure to place the rearward.)
19. Tighten two inboard flange bolts. Torque the flange bolts to 22 N·m (16 lb·ft).
20. Repeat steps 18 and 19 on the right side of the vehicle.
9 (1810) 9 of 12
If the vehicle is equipped with the one-piece floor under cover, continue with step 21; if the vehicle is equipped with the separate floor under covers, go to step 22.
With one-piece floor under cover21. Install the floor under cover. Torque the flange nuts
and washer-bolts to 6.9-11.8 N·m (5.1-9 lb·ft). Go to step 24.
8 WASHER-BOLTS6.9-11.8 N·m (5.1-9 lb·ft)
FLOOR UNDER COVER
17 LARGE CLIPS
CLIP
2 FLANGE NUTS6.9-11.8 N·m (5.1-9 lb·ft)
FRONT
10 of 12 AII10312-0
With separate floor under covers22. Install the left floor under cover. Torque the flange
nut and washer-bolts to 6.9-11.8 N·m (5.1-9 lb·ft).
3 WASHER-BOLTS6.9-11.8 N·m (5.1-9 lb·ft)
LEFT FLOOR UNDER COVER
7 LARGE CLIPS
2 CLIPS
FLANGE NUT6.9-11.8 N·m (5.1-9 lb·ft)
FRONT
23. Install the right floor under cover. Torque the flange nut and washer-bolts to 6.9-11.8 N·m (5.1-9 lb·ft).
2 WASHER-BOLTS6.9-11.8 N·m (5.1-9 lb·ft)
FLANGE NUT6.9-11.8 N·m (5.1-9 lb·ft)
2 CLIPS
RIGHT FLOOR UNDER COVER
6 LARGE CLIPS
FRONT
9 (1810) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
24. Loosely secure bracket A to the vehicle panel with four flange bolts.NOTE: If there are black and silver flange bolts in the kit, use the silver flange bolts.
4 FLANGE BOLTS(Use the silver flange bolts if included in the kit.)(Loosely secure.)
BRACKET A
VEHICLE PANEL
FRONT
25. Loosely secure bracket C and left bracket D to the vehicle panel with three flange bolts.NOTE: If there are black and silver flange bolts in the kit, use the silver flange bolts.
3 FLANGE BOLTS(Use the silver flange bolts if included in the kit.)(Loosely secure.)
BRACKET C
VEHICLE PANEL
FRONT
LEFT BRACKET D
© 2018 American Honda Motor Co., Inc. – All Rights Reserved. AII10312-0
26. With the help of an assistant, loosely secure the left running board to bracket A, bracket B, bracket C, and left bracket D with 13 flange bolts.NOTE: If there are black and silver flange bolts in the kit, use six black flange bolts and seven silver flange bolts as shown.
12 FLANGE BOLTS(Loosely secure.)
BRACKET C
FRONT
LEFT RUNNING BOARD
LEFT BRACKET D
BRACKET B
BRACKET A
FLANGE BOLT(Use the silver flange bolt if included in the kit.)(Loosely secure.)
LEFT RUNNING BOARD
FRONT
Make sure to use the black flange bolts in these inboard six places.
Use the silver flange bolts in these outboard six places if included in the kit.
9 (1810) 11 of 12
27. Secure bracket A, bracket B, and bracket C to the vehicle panel with nine flange bolts. Torque the flange bolts to 22 N·m (16 lb·ft).
BRACKET B
VEHICLE PANEL
3 FLANGE BOLTS22 N·m (16 lb·ft)
FRONT
4 FLANGE BOLTS22 N·m (16 lb·ft)
2 FLANGE BOLTS22 N·m (16 lb·ft)
BRACKET A
BRACKET C
FRONT
12 of 12 AII10312-0
28. Secure the left running board to bracket A, bracket B, bracket C, and left bracket D with 13 flange bolts. Torque the flange bolts to 22 N·m (16 lb·ft).
Adjust to be parallel.
FLANGE BOLT22 N·m (16 lb·ft)
FRONT
BRACKET A, BRACKET B, BRACKET C
12 FLANGE BOLTS22 N·m (16 lb·ft)
LEFT RUNNING BOARD
LEFT RUNNING BOARD LEFT
BRACKET D
FRONT
29. Repeat steps 24 through 28 on the right side of the vehicle.
9 (1810) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
