Card reader Sirius i30

Installation manual

o Product o Installation o Connection o Technical data

Publication

November 2014,

Keyprocessor BV

Paasheuvelweg 20

1105BJ Amsterdam, The Netherlands

www.keyprocessor.com

Tel.: +31-20-4620700

This manual represents the knowledge at the above mentioned time. Keyprocessor works non-

stop to improve her products. For the most recent technical information please contact your

consultant or dealer.

Content overview

Publication .................................................................................................................... 2 Content overview .......................................................................................................... 2 1 The product .................................................................................................... 3 1.1 Sticker i-serie ............................................................................................. 3 1.2 Spacers ...................................................................................................... 4 1.3 Default reader configurations ........................................................................ 4 1.3.1 Polyx/Orbit Mifare- MifareDesfire ................................................................... 4 1.3.2 Chip Serial Number (CSN) ............................................................................ 5 1.3.3 Sirius i-30 programmable using configuration cards ......................................... 5 1.3.4 Sirius i-30 programmable using PC application and configuration cards .............. 5 2 Installation and use ......................................................................................... 6 2.1 Location ..................................................................................................... 6 2.2 Mounting .................................................................................................... 6 3 Connection ..................................................................................................... 8 3.1 Sirius i30 connector lay-out .......................................................................... 8 3.2 If door controller Polyx ................................................................................. 9 3.2.1 Direct connection (RS485) ........................................................................... 9 3.2.2 Connection using an Adapterboard ............................................................... 10 3.3 If door controller Orbit ................................................................................ 11 3.3.1 Connecting with UTP cable ........................................................................... 11 3.3.2 Connection with CKY 3x2x0,14mm² .............................................................. 11 4 Technical data................................................................................................ 12 4.1 Cabel specifications .................................................................................... 13 4.1.1 Data signal Clock/Data ................................................................................ 13 4.1.2 Data signal Wiegand ................................................................................... 13 4.1.3 Data signal RS485 ...................................................................................... 14 4.2 Certificates ................................................................................................ 15

1 The product

The Sirius i-series card reader is a versatile card reader which supports multiple card

technologies and communication protocols. In addition, this card reader is able to support

different technologies simultaneously like Mifare classic and DESFire EV1.

The card reader is equipped with a function to automatically adjust the antenna on and off

when no activity takes place around the card reader. The detection is based on proximity.

The purpose of this functionality is to create a card reader as energy efficient as possible and

only activate the antenna when a person or card is detected near to the card reader.

This manual provides the necessary information concerning the installation instructions,

mounting and use of the card reader which is supplied as standard.

The Sirius i-series card reader:

i30: picture 1 i30: Picture 2

1.1 Sticker i-serie

On the back of the card reader a sticker placed.

This sticker features a QR code.

After scanning this QR code, all necessary information

will be downloaded automatically.

1.2 Spacers

Several types of Spacers have been developed for specific purposes. It can make the card

reader more robust for external influences but it can also be useful when installing the Sirius

card reader on existing plants.

801-6101 Sirius i30 Spacer

801-6102 Sirius i30 Spacer wide

801-6107 Sirius i30 Mounting plate for Sirius i30 spacer protector (801-6109)

801-6109 Sirius i30 Spacer protector

801-6110 Sirius i30 Spacer cardholder

1.3 Default reader configurations

When using a default Sirius i-series card reader, four configurations are possible

The configurations are described in the paragraphs below.

Remark: For more information about the additional options, please contact your contact at

Keyprocessor.

1.3.1 Polyx/Orbit Mifare- MifareDesfire

Part number: 801-5101

Standard communication:

A Polyx based on RS485

An Orbit based on Clock/Data - MIFARE Classic & MIFARE DESFire EV1(coded)

Output length when using Clock/Data:

When using Mifare Classic, the output length is 8 digits

When using Mifare DESFire, the output length is 12 digits

Standard LED function:

When the reader is provided with power, the LED color is Red.

When the LED connection is switched to GND, the LED color is Green

Standard IO function:

When using Mifare Classic, the output length is 8 digits

A standard configured card reader does not use the extra IO functionality. When this

function is needed, you need to order another card reader. See chapter 1.3.3 & 1.3.4

Programmable:

The card reader is not programmable.

1.3.2 Chip Serial Number (CSN)

Part number: 801-5102

Default Card reader protocol:

An Orbit based on Clock/Data.

Output length based on Clock/Data:

The length of the Chip Serial Number (CSN) is 4 byte swapped (10 digits decimal)

Attention! When using a 7 byte (random) CSN, the card reader must communicate with a

Polyx. In this case you need to order another card reader. See chapter 1.3.3 &

1.3.4

Standard LED function:

When the reader is provided with power, the LED color is Red.

When the LED connection is switched to GND, the LED color is Green

Standard IO function:

A standard configured card reader does not use the extra IO functionality. When this

function is needed, you need to order another card reader. See chapter 1.3.3 & 1.3.4

1.3.3 Sirius i-30 programmable using configuration

cards

Part number: 801-5103

After connecting the Power to the card reader, the LED turns blue. A configuration card

is needed to turn the reader in operational mode.

You can order a configuration card via Keyprocessor. To create 'custom' configuration

cards extra costs will be calculated.

1.3.4 Sirius i-30 programmable using PC application

and configuration cards

Part number: 801-5104

After connecting the Power to the card reader, the LED turns blue. A configuration card

is needed to turn the reader in operational mode.

The card reader is fully programmable using a PC application and you’re able to create

your own configuration cards.

2 Installation and use

2.1 Location

Determine the location where the Sirius card reader should be installed. There is a

maximum cable length between the reader and door controller.

Exception: using an external power supply, you can increase the achievable distance

between the door controller and card reader.

Install the reader with a minimum lateral distance of 20 cm from each other.

The reader should preferably NOT be installed to metal. If necessary, use a spacer, see

chapter 1.2.

2.2 Mounting

Mount the card reader preferably on a flat surface.

Picture 3: Sirius i30 measurements

Mount the back plate of the card reader to the appropriate place.

If placed on a stone wall, drill two 6mm holes intended for the plugs.

If placed on a wooden surface, drill two 3mm holes.

The screw hole of the card reader should be placed on the underside. (see Picture 4)

Pull the cable through the mounting plate (and the spacer, if applicable) of the Sirius

reader.

Screw the back plate of the reader with adequate screws. The head of the screw must

be at least 6 mm wide.

When not removed, remove the orange colored film of the Buzzer.

Click the front of the card reader at the top of the mounting plate

Attach the front of the card reader to the mounting plate with the supplied 'special

mounting bolt.

3 Connection

Remark! Depending on the configuration of the card reader, the inputs and outputs of the

card reader can be used.

3.1 Sirius i30 connector lay-out

Connect the cable as shown in this chapter

The reader accepts a supply voltage of 5.0 - 16.0 VDC.

A higher input voltage results in a lower power consumption and provide cost-effective wiring

with a smaller diameter of the conductor.

When using an external power supply, it must comply with the SELV guidelines.

Pin number Clock/Data Wiegand RS485

7 Vcc (+) Vcc (+) Vcc (+)

6 GND (-) GND (-) GND (-)

5 Ext. Input 1(LED) Ext. Input 1(LED) Ext. Input 1

4 Clock D1 Ext. Output 2

3 Data D0 Ext. Output 1

2 Ext. Input 2 Ext. Input 2 B

1 Ext. Output 1 Ext. Output 1 A

3.2 If door controller Polyx

The Sirius card reader can be connected in two ways with the Polyx: directly or by using an

Adapterboard

For optimal communication, it is recommended to have the latest version of one of the

following operating system

2.6 JFSS2

3.3 UbiFS

Remark! Browse to the polyx to see the version information. For more information about

the versions, see the KP_Install_update_Polyx manual.

3.2.1 Direct connection (RS485)

Recommended cable type between a Polyx and the Sirius card reader is: (see Section 4.1 for

more information)

CAT5 UTP four twisted pairs of 24AWG copper conductors

CAT6 UTP four twisted pairs of 24AWG copper conductors

A direct connection (without using an Adapterboard) between the Sirius card reader and a

Polyx™ is NOT possible when:

Sirius and Polyx™ are installed in different buildings and thus the connection

leaves the building or

the wiring is no UTP cable (CAT5 or CAT6) or

an existing (non UTP) cable is reused or

overvoltage protection for the card reader is required or

An external power supply is required for the card reader.

If any of the above conditions applies, see chapter 3.2.2.

Polyx, directly connected to a Sirius card reader:

Pin number RJ-

45 Plug

Polyx™ PRT 2/3

TIA/EIA-568-B

Cable color

Signal Connection

Sirius i30 card

reader

1 White/orange B 2 2 Orange A 1 3 White/green B 2 4 Blue Vcc (+) 7 5 White/blue 6 Green A 1 7 White/brown 8 Brown GND (-) 6

Picture T-568B

3.2.2 Connection using an Adapterboard

Recommended cable type between a Polyx and the Sirius card reader, using an Adapterboard

is:

Shielded cable with twisted pairs

If a direct connection is not possible, an Adapterboard must be placed between Polyx and the

Sirius card reader.

Adapterboard and Polyx are connected with a default UTP cat5 cable (or higher) (plug

connection).

Connecting wires as shown in the diagrams below.

Or screw

connection

on Adapterboard

Or RJ45

connection

on

Adapterboard

TIA/EIA-568-B

Cable color

Signal Connection

Sirius i30 card

reader

A (or 1) 1 White/orange B 2

B (or 2) 2 Orange A 1

Y (or 3) 3 White/green B 2

“+” 4 Blue Vcc 7

5 White/blue

Z (or 6) 6 Green A 1

7 White/brown

“—” 8 Brown GND (-) 6

Connect GND of the Adapterboard to the local Earth.

Connect the shield of the ground cable to the GND connection of the Adapterboard.

Do not place any jumpers! For more information see the Adapterboard manual..

Possible connections of the card reader Sirius on the Adapterboard

3.3 If door controller Orbit

Recommended cable type between the Orbit and Sirius card reader:

CKY 3x2x0,14mm²

CKY 4x2x0,14mm²

CAT5 UTP four twisted pairs of 24AWG copper conductors

CAT6 UTP four twisted pairs of 24AWG copper conductors

3.3.1 Connecting with UTP cable

TIA/EIA-568-B

Cable color

Connection

on the Orbit

Connection

Sirius i30 card reader

White/orange Data/D0 3 Orange - - White/green Clock/D1 4 Blue +5V 7 White/blue LED 5 Green - - White/brown GND 6 Brown GND 6

3.3.2 Connection with CKY 3x2x0,14mm²

Cable color Connection

on the Orbit

Connection

Sirius i30 card reader

Green Data/D0 3 Yellow Clock/D1 4 Pink +5V 7 Grey LED 5 White GND 6 Brown GND 6

4 Technical data

Model Sirius i30 card reader

Interface Sirius Clock/Data, Wiegand Sirius - Polyx™ (RS485)

Data type Read Read/write

Readable cards Mifare 1K, Mifare 4K, Mifare

DESFire 0.6, Mifare DESFire EV1

8K and ISO14443A compatible

card

Mifare 1K, Mifare 4K, Mifare

DESFire 0.6, Mifare DESFire

EV1 8K, Rijkspas and

ISO14443A compatible card

Power supply 5-16V DC Average: 0,7W

Peak: 1,4W

5-16V DC Average: 0,7W

Peak: 1,4W

Led consumption, both on

100%

On 12V, max. 1,8W

LED input LED input with pull-up, active low

Ext. output max. Voltage 45V; Open collector output; sinked current. Max.

current 500mA

Ext. input 1 Resistance 1kOhm

Dimensions (mm) i30 142x45x22

Reading Distance i30 5mm-70mm for ISO14443A Mifare card; (depending on

environment and transponder)

Environmental Rating i30 IP64

Operating Temperature -31º to 150º F (-35º to 65º C)

Storage Temperature -67º to 185º F (-55º to 85º C)

Operating Humidity 5% to 95% relative humidity non-condensing

Transmit Frequency 13.56 MHz

Standard ISO14443 A

Indicators 2x RGB LED and 1 buzzer

Connection 7-pin screw connector

Certifications CE

4.1 Cabel specifications

Cable specifications (non-shielded)

4.1.1 Data signal Clock/Data

4.1.2 Data signal Wiegand

Interface

Maximum cable length

min.conductor size with

12 VDC supply 1 = 5V DC

Meters Feet mm2 AWG

Wiegand

40 130 0.14 26

80 260 0.25 24

120 390 0.34 22

Clock/Data 201 661

0.14 26

0.25 24

0.34 22

RS485 (cable

power)

120 200 0.25 24

150 490 0.34 22

RS485 (external

power) 600 1965 0.25 24

4.1.3 Data signal RS485

4.2 Certificates