Installation InstructionS RB 500 Manual Roller … the blind against the bearing and slide it out of...
6
5-211 Series-Chain Operation Installation InstructionS RB 500 Manual Roller Shades Heavy Duty Clutch System 1
Transcript of Installation InstructionS RB 500 Manual Roller … the blind against the bearing and slide it out of...
Push the blind against the bearing and slide it out of the bracket.
5-211 Series-Chain Operation
Installation InstructionS RB 500 Manual Roller ShadesHeavy Duty Clutch System
Open both fasteners of the bracket ring. Turn the blind in the roll up direction until the front plate gets out of the bracket ring.
Lift the backside of the end cap and slide it towards you.
Unfasten the locking ring.
Removal
2 1
2
1
1
Push the blind against the bearing and slide it out of the bracket.
5-211 Series-Chain Operation
Installation InstructionS RB 500 Manual Roller ShadesHeavy Duty Clutch System
Open both fasteners of the bracket ring. Turn the blind in the roll up direction until the front plate gets out of the bracket ring.
Lift the backside of the end cap and slide it towards you.
Unfasten the locking ring.
Removal
2 1
2
1
1
katherinemills
Sticky Note
replace with new logo - doesn't need to be this big - approved size to be used throughout all RB 500 installation instructions
1
2
21
a
c
b
click
click
click
Slide the screw cover onto the bracket until it snaps.
Open the fastener on the bracket adapter (A).
Install the brackets with the screws provided.
a) recess b) ceiling c) wall
Place the roller shade with the idle end onto the bracket. Push the shade against the idle end and lift the shade up with the chain facing straight down...
Fix the roller shade by turning the locking ring against the idle end.
Slide the end caps onto the brackets. Make sure that the end caps snap onto the brackets.
ring. Turn the roller shade (10°) in the rolling off di-rection and close both fasteners of the bracket ring.
To adjust skewing, put the provided Allen key into the screw of the leveler and turn it left or right to move the shade up and down. Support lifting of large heavy roller shades with the palm of your hand.
Installation Option: Leveler
Make sure that the opening for the Allen key is pointing downwards before installing the brackets. Change the orientation by loosening the 4 screws (M5 x 8) and turning the leveler 90°. Fix the screws.
2
A
1
2
21
a
c
b
click
click
click
Slide the cover cap onto the bracket until it snaps.
The fasteners of the bracket ring must be open.
Fix the bracket with the screws provided.
a recess b ceiling c wall
Place the roller shade with the idle end onto the bracket. Push the shade against the idle end and lift the shade up ...
Secure the shade by turning the locking ring furthest away from the bracket.
Attach the bracket covers onto the brackets. Make sure the bracket covers snap onto the brackets.
...line up teeth with bracket adapter (A).Insert clutch into bracket, turn shade (10°) in the rolling off direction(1), and close fastener on the bracket adapter.
To adjust skewing, put the provided Allen key into the screw of the leveler and turn it left or right to move the shade up and down. Support lifting of large heavy roller shades with the palm of your hand.
Installation Option: Leveler
Make sure that the opening for the Allen key is pointing downwards before installing the brackets. Change the orientation by loosening the 4 screws (M5 x 8) and turning the leveler 90°. Fix the screws.
3
A
1
2
21
a
c
b
click
click
click
Slide the cover cap onto the bracket until it snaps.
The fasteners of the bracket ring must be open.
Fix the bracket with the screws provided.
a recess b ceiling c wall
Place the roller shade with the idle end onto the bracket. Push the shade against the idle end and lift the shade up ...
Fix the roller shade by turning the locking ring against the idle end.
Slide the end caps onto the brackets. Make sure that the end caps snap onto the brackets.
ring. Turn the roller shade (10°) in the rolling off di-rection and close both fasteners of the bracket ring.
To adjust skewing, put the provided Allen key into the screw of the leveler and turn it left or right to move the shade up and down. Support lifting of large heavy roller shades with the palm of your hand.
Installation Option: Leveler
Make sure that the opening for the Allen key is pointing downwards before installing the brackets. Change the orientation by loosening the 4 screws and turning the leveler 90°. Reinstall the screws.
4
2 1
21
Push the roller shade against the idle end and slide it out of the bracket.
Type 5-211
Installation Instruction Roller ShadeChain Operation
Open fastener on the bracket adapter. Turn the roller shade 10° in the roll up direction(1). Pull clutch out of the bracket adapter (2).
Lift the backside of the end cap and slide it towards you.
Unfasten the locking ring.
Removal
5
2 1
21
Push the roller shade against the idle end (1) and slide it out of the bracket (2).
Type 5-211
Installation Instruction Roller ShadeChain Operation
Open both fasteners of the bracket ring. Turn the roller shade in the roll up direction until the front plate gets out of the bracket ring.
Lift the backside of the end cap and slide it towards you.
Unfasten the locking ring.
Removal
6
