INSTALLATION INSTRUCTIONS JD 2032 & 2038 Wiring …...connects a TKV 20 to John Deere 2032 and 2038...

4
1 Installation Instructions NOTE: BE SURE THAT YOUR TRACTOR IS IN PARK AND THAT YOU’VE GIVEN THE ENGINE SUFFICIENT TIME TO COOL, IF PREVIOUSLY IN USE. DISCONNECT BATTERY. INSTALLATION INSTRUCTIONS JD 2032 & 2038 Wiring Harness Kit ( TK95056 ) Kit Includes Description Part No. Qty. A Relay Harness ST50754 1 B Extension Harness ST48298 1 C Switch Harness DPDT ST48299 1 D 30A Mini Blade Fuse ST50755 1 E Hardware Kit N/A 1 F Zip Ties N/A 10 A dedicated wiring harness connects the TKV 20 to your tractor. Included is a rocker switch to operate the electric actuator. This wiring harness connects a TKV 20 to John Deere 2032 and 2038 Compact Tractors. 1. Remove pedestal cover and left side engine cover. 2. Open fuse box under engine cover and replace bottom 20A fuse with supplied 30A slow blow fuse 3. Close up fuse box and reinstall engine cover. 4. Connect ring terminals on Relay Harness to junction block on left side of pedestal. Bottom: red wire; left: black wire; top: yellow wire. A B C Red Black Yellow

Transcript of INSTALLATION INSTRUCTIONS JD 2032 & 2038 Wiring …...connects a TKV 20 to John Deere 2032 and 2038...

1

Installation InstructionsNOTE: BE SURE THAT YOUR TRACTOR IS IN PARK AND THAT YOU’VE GIVEN THE ENGINE SUFFICIENT TIME TO COOL, IF PREVIOUSLY IN USE. DISCONNECT BATTERY.

INSTALLATION INSTRUCTIONS

JD 2032 & 2038 Wiring Harness Kit (TK95056)

GREYPMS 427CMYK C19 M15 Y16 K0RGB R204 G204 B204Hex #CCCCCCThrea Light Ash

BLUEPMS 647CMYK C91 M60 Y4 K0RGB R20 G103 B172Hex #1268ACThread Farm Blue

ORANGEPMS 715CMYK C0 M69 Y98 K0RGB R243 G113 B33Hex #F37121Thread Tennessee Orange

GREYPMS 428CMYK C27 M17 Y17 K0RGB R195 G197 B200Hex #c3c5c8Thread Light Gray

BLUEPMS 287CMYK C100 M87 Y20 K10RGB R32 G61 B124Hex #203d7cThread Dark Royal

BLACKPMS TBDCMYK C0 M0 Y0 K100RGB R0 G0 B0Hex #000000Thread Black

GOLDPMS 3965CMYK C1 M14 Y99 K0RGB R254 G212 B2Hex #�d402Thread NFL Yellow

DARK BLUE

CMYK C98 M74 Y24 K08RGB R14 G78 B129 HEX# 0E4E81

PANTONE 301

THREAD Empire

LIGHT BLUE

CMYK C56 M24 Y06 K00RGB R113 G164 B205 HEX# 71A4CD

PANTONE 645

THREAD Light Blue

MEDIUM BLUE

CMYK C90 M59 Y04 K00RGB R18 G104 B172 HEX# 1268AC

PANTONE 3015

THREAD Farm Blue

Kit IncludesDescription Part No. Qty.

A Relay Harness ST50754 1

B Extension Harness ST48298 1

C Switch Harness DPDT ST48299 1

D 30A Mini Blade Fuse ST50755 1

E Hardware Kit N/A 1

F Zip Ties N/A 10

A dedicated wiring harness connects the TKV 20 to your tractor. Included is a rocker switch to operate the electric actuator. This wiring harness connects a TKV 20 to John Deere 2032 and 2038 Compact Tractors.

1. Remove pedestal cover and left side engine cover.

2. Open fuse box under engine cover and replace bottom 20A fuse with supplied 30A slow blow fuse

3. Close up fuse box and reinstall engine cover.

4. Connect ring terminals on Relay Harness to junction block on left side of pedestal. Bottom: red wire; left: black wire; top: yellow wire.

AB

C

Red

Black

Yellow

2

5. Secure relay to main harness with zip tie.

6. Remove throttle connector and 4 bolts on ECU from the right side of the pedestal.

7. Feed Relay Harness from left side of pedestal to right side and down to platform.

8. Reinstall 4 bolts on ECU and reconnect throttle harness.

9. Reinstall the pedestal cover.

10. Route Relay Harness under platform staying clear of any moving linkage and securing with wire ties.

11. Route Relay Harness up under seat frame beside fuse box to rear of right fender.

12. Loosen 2 screws on deck height stick and remove 2 screws on console panel and lift panel off fender.

13. Remove switch blank and install supplied rocker switch as shown.

14. Continue to route Relay Harness into console and connect to Switch Harness.

3

15. Connect actuator Extension Harness to Switch Harness and route through console to rear of fender.

16. Wrap remaining Extension Harness around ROPS when not in use.

17. Reinstall console, reinstall 2 screws and retighten 2 screws on deck height stick.

18. Use the Zip Ties to secure the Wiring Harness to the tractor’s existing wiring. Apply these to areas to prevent wires from hanging too low and/or making contact with moving parts.

WarrantyTerraKing’s products are guaranteed to be free from defects in material and/or workmanship and to perform as advertised when properly assembled, installed, used, and maintained in accordance with written instructions. Failure to adhere to this will void the warranty. TerraKing will not be responsible for labor, loss, or consequential damage of any kind or character caused by defective parts, or for charges incurred in the replacement or repair of defective parts. TerraKing reserves the right to request photos or return of damaged/defective parts. To submit a claim, please have your original purchase date and a copy of your receipt (if available).

Warranty PeriodThe TerraKing Wirng Harness Kit is warranted for a period of 1 (one) year after the purchase date for residential use, and 6 (six) months after the purchase date for commercial use. This product is warranted by TerraKing to the original purchaser/customer against defects in material and work-manship under normal operating conditions.

4

TerraKing by Superior Tech, Inc. [email protected] # TKMI-007B-08/18