INS

TA

LL

AT

ION

INS

TR

UC

TIO

NS

SLIDING DOOR

343-1307BSIDE 1 OF 6 (10/08)

Illustration 1. Hook Plate Installation:

Illustration 2. Hook Bracket Installation:

3

6

"

p

a

n

e

l

r

u

n

o

p

e

n

in

g

3

6

"

p

a

n

e

l

r

u

n

o

p

e

n

in

g

Hook plate - at panel run opening,

measure up from floor and locate a

panel slot (bottom edge of slot)

between dimensions as defined in

Table 1. Insert bottom tab of

hook plate into panel slot.

Hook bracket - on opposite side of panel

frame and at same height as hook plate,

insert hook bracket tabs into panel slots

and wrap bracket around side of panel

frame. Position hook bracket over

hook plate and align holes in each

bracket.

Bottom tab

Tab

Hook plate

X

Panel frame

Bottom of

panel slot

Panel frame

Panel frame

Panel frame

Important - installation of panels must be

completed before installing sliding door.

Table 1

Panel System “X” Dimension

Concensys X = 7-

3

/4" to 8-

3

/4"

Terrace 3.4 X = 7-

1

/8" to 8-

1

/8"

Terrace 2.6 X = 7-

1

/8" to 8-

1

/8"

Stride X = 7-

3

/4" to 8-

3

/4"

Align X = 7-

3

/4" to 8-

3

/4"

Terrace DNA X = 7-

3

/4" to 8-

3

/4"

343-1307BSIDE 2 OF 6 (10/08)

SLIDING DOORIllustration 3. Attach Bottom Rail Assembly:

Illustration 4. Attach Anti-Dislodgement Bracket:

Bottom rail assembly - position bottom

rail assembly onto hook bracket and

install four screws (provided) through

bottom rail assembly, hook bracket, and

into hook plate.

Anti-dislodgement bracket -

measure up from bottom of

bottom rail assembly and

locate a panel slot, on each

end of panel, approximately

the dimension defined in

their appropriate Table listed

below. Insert bottom tab of

each anti-dislodgement

bracket into panel slots and

pivot bracket toward panel.

Panel frame

Panel frame

Panel frame

Bottom rail

assembly

Hook bracket

#10 flat head thread cutting screw

X

Bottom tab

Bottom tab

3

6

"

p

a

n

e

l

r

u

n

o

p

e

n

in

g

Table 2Panel

System69" TallPanel

82" TallPanel

Concensys X=58-

5

/8" X=71-

5

/8"

Terrace 3.4 X=62" X=75"

Terrace 2.6 X=62" X=75"

Table 3 (Stride & Terrace DNA)50" TallPanel

65" TallPanel

80" TallPanel

X=41-

5

/8" X=56-

5

/8" X=71-

5

/8"

Table 4 (Align)68" TallPanel

84"TallPanel

X=59-

5

/8" X=75-

5

/8"

343-1307BSIDE 3 OF 6 (10/08)

SLIDING DOORIllustration 5. Attach Top Rail Assembly:

Illustration 6. Connect Top Rail Assembly to Anti-Dislodgement Brackets:

Top rail assembly - insert top rail assem-

bly hooks into panel slots directly

below anti-dislodgement brackets. Top

rail assembly brackets sit overtop anti-

dislodgement brackets.

#10 pan head sheet metal screw

(provided) - install through hole

in top rail assembly bracket

and into hole in anti-dislodge-

ment bracket.

Top rail assembly

Panel frame

Panel frame

Panel frame

Hook

Top rail assembly bracket

Anti-dislodgement bracket

Hook

3

6

"

p

a

n

e

l

r

u

n

o

p

e

n

in

g

343-1307BSIDE 4 OF 6 (10/08)

SLIDING DOORIllustration 7. Install Rear Door Stop and Attach Sliding Door to Top Track Assembly:

Rubber stop - at rear of door, attach

rubber stop to door lower track blade

with screw provided.

Sliding door - insert door upper track

blade into upper track assembly.

Important - install rear door stop before

attaching sliding door to upper door track.

#10 flat head thread

cutting screw

Upper track

assembly

Upper track

blade

Lower track

blade

Panel frame

343-1307BSIDE 5 OF 6 (10/08)

SLIDING DOORIllustration 8. Attach Sliding Door to Bottom Track Assembly:

Illustration 9. Install Front Door Stop:

Sliding door - slide door along upper

track assembly until door lower track

blade feeds into bottom track

assembly.

Lower track

assembly

Upper track assembly

Lower track

blade

Panel frame

Panel frame

Panel frame

Rubber stop - attach rubber

stop to door lower track blade

with screw provided.

Sliding door - slide door forward to

access front of lower track blade.

#10 flat head

thread cutting

screw

Lower track

blade

3

6

"

p

a

n

e

l

r

u

n

o

p

e

n

in

g

343-1307BSIDE 6 OF 6 (10/08)

SLIDING DOORIllustration 10. Install Sliding Door Handle:

Door handle - measure up from bottom of door

frame 31" and use masking tape to mark

location on sliding door. Remove protective

backing from mounting tape on back of door

handle and carefully place handle, above

marked location, flat against door frame and

door filler material.

Repeat procedure to attach second door handle

onto interior side of sliding door (slide door

forward as needed). Ensure second door handle

is positioned directly behind first door handle

(any offset of door handles will show through

door filler material).

Panel frame

Sliding door

frame

Sliding door

filler material

Panel frame

3

1

"

~

3

6

"

p

a

n

e

l

r

u

n

o

p

e

n

in

g

Step 1 - Clean the plastic surface with a cleaning solvent

(Glass Cleaner)

Step 2 - Wipe surface dry

Step 3 - Remove tape backer and apply the handle to the

plastic insert surface

Step 4 - Apply pressure to the handle to insure proper adhe-

sion. Bond will be held better if the assembly is left

without use for 12 hours.