INSTALLATION ILLUMINATED DOOR VERSION 1 …...ILLUMINATED DOOR VERSION 1 SILL TRIM P/N 08E12-T7S-100...
Transcript of INSTALLATION ILLUMINATED DOOR VERSION 1 …...ILLUMINATED DOOR VERSION 1 SILL TRIM P/N 08E12-T7S-100...
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2017 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
ILLUMINATED DOOR SILL TRIMP/N 08E12-T7S-100
served. AII07065-02 (170
2018 HR-V
7) 0
Issue Date
JUL 2017
PARTS LIST
Left front illuminated door sill trim
Right front illuminated door sill trim
Left rear door sill trim (Identification mark: L)
Right rear door sill trim (Identification mark: R)
Door sill trim harness
Fuse label
20 Wire ties
Protective tape
2 Protective clips
2 Alcohol swabs
1 of 168E12-T7S-1000-90
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
10 mm Open end wrench
Ruler
Masking tape
Tape
Felt-tip pen
Scissors
Utility knife
Needle nose pliers
Diagonal cutters
Isopropyl alcohol
Shop towel
The following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Illuminated Door Sill Trim in the Vehicle
QD40332AH
RIGHT FRONT ILLUMINATED DOOR SILL TRIM
LEFT FRONT ILLUMINATED DOOR SILL TRIM
RIGHT REAR DOOR SILL TRIM
LEFT REAR DOOR SILL TRIM
2A FUSE
DOOR SILL TRIM HARNESS
2 of 16 AII07065-0
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Disconnect the negative cable from the battery.
2. Pull away the door opening seal, and attach masking tape to the vehicle panel at the measurement shown.
QD40301AH
45 mm (1.8 in.)
MASKING TAPE
DOOR OPENING SEAL(Pull away.)
PASSENGER’S FRONT DOOR SILL TRIM
MASKING TAPE
VEHICLE PANEL
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
3. Remove the passenger’s front door sill trim.
CLIP 3 RETAINING TABS
3 RETAINING TABS
PASSENGER’S FRONT DOOR SILL TRIM
4. Remove the passenger’s under cover.
QD40852AH
3 CLIPS
PASSENGER’S UNDER COVER
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
5. Pull away the door opening seal, and remove the passenger’s kick panel.
QD40303AH2 CLIPS
DOOR OPENING SEAL(Pull away.)
PASSENGER’S KICK PANEL
2 (1707) 3 of 16
6. Pull away the door opening seal, and remove the passenger’s dashboard side lid.
QD40853AH
DOOR OPENING SEAL(Pull away.)
5 RETAINING TABS
PASSENGER’S DASHBOARD SIDE LID
PLASTIC TRIM TOOL
7. Remove the two bolts from the glove box.
QD40854AH
2 BOLTS
GLOVE BOX
4 of 16 AII07065-0
8. Pull away the door opening seal. Open and remove the glove box.
QD40855AH2 BOLTS
5 CLIPSDOOR OPENING SEAL(Pull away.)
9. Pull away the door opening seal, and remove the driver’s dashboard side lid.
QD40315AJ
DRIVER’S DASHBOARD SIDE LID
PLASTIC TRIM TOOL
DOOR OPENING SEAL(Pull away.)
6 RETAINING TABS
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
10. Attach the tape to the lower column cover.
QD40316AJTAPELOWER COLUMN COVER
11. Pull away the door opening seal, and remove the driver’s dashboard lower cover and unplug the vehicle connectors.
QD40317AJ11 CLIPSDRIVER’S DASHBOARD LOWER COVER
CLIPVEHICLE CONNECTORS
DOOR OPENING SEAL(Pull away.)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
12. Pull away the door opening seal, and attach masking tape to the vehicle panel at the measurement shown.
QD40304AHDOOR OPENING SEAL(Pull away.)
45 mm (1.8 in.)
MASKING TAPE
DRIVER’S FRONT DOOR SILL TRIM
MASKING TAPE
VEHICLE PANEL
13. Remove the driver’s front door sill trim.
3 RETAINING TABS CLIP
DRIVER’S FRONT DOOR SILL TRIM 3 RETAINING
TABS
2 (1707) 5 of 16
14. Pull away the door opening seal, and remove the driver’s kick panel.
QD40320AJ
DOOR OPENING SEAL(Pull away.)
DRIVER’S KICK PANEL
2 CLIPS
• If the vehicle is equipped with automatic climate control, continue with step 15. If not, go to step 18.
With automatic climate control
15. Apply tape to the climate control unit, center console panel, center console pad, and shift lever as shown. Shift the shift lever to D.
QD41602AJ
TAPESHIFT LEVER(D POSITION)
CENTER CONSOLE PANEL CENTER
CONSOLE PAD
CLIMATE CONTROL UNIT
6 of 16 AII07065-0
16. Remove the center console switch trim and unplug the vehicle connector.
QD41603AJ
CENTER CONSOLE SWITCH TRIM2 CLIPS
VEHICLE CONNECTOR
2 RETAINING TABS
17. Remove the climate control unit and unplug the vehicle connectors. Go to step 23.
QD40856AH
CLIMATE CONTROL UNIT 5 CLIPS
VEHICLE CONNECTORS
CLIP
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
With manual climate control
18. Apply tape to the heater control panel, center console panel, center console pad, and shift lever as shown. Shift the shift lever to D.
QD41604AJ
TAPESHIFT LEVER(D POSITION)
CENTER CONSOLE PANEL CENTER
CONSOLE PAD
HEATER CONTROL PANEL
19. Remove the center console switch trim and unplug the vehicle connector.
QD41605AJ
2 CLIPSCENTER CONSOLE SWITCH TRIM
VEHICLE CONNECTOR
2 RETAINING TABS
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
20. Set the mode control dial and the temperature control dial as shown.
QD40857AH
MODE CONTROL DIAL(VENT)
TEMPERATURE CONTROL DIAL(MAX COOL)
HEATER CONTROL PANEL
2 (1707) 7 of 16
21. Remove the mode control cable and air mix control cable:
• Remove the control cable from the clamp and the groove.
• Remove the inner cable from the control linkage.
QD40858AH
MODE CONTROL CABLE
AIR MIX CONTROL CABLE
CONTROL LINKAGE
INNER CABLE
CONTROL CABLE
CLAMP
GROOVE
CONTROL LINKAGE
INNER CABLE
CONTROL CABLE
CLAMP
GROOVE
8 of 16 AII07065-0
22. Remove the heater control panel and unplug the vehicle connectors.
QD40859AH
5 CLIPS
VEHICLE CONNECTORS
HEATER CONTROL PANEL
2 CLIPS
23. Using isopropyl alcohol on a shop towel, clean the fuse case where the fuse label will attach.
QD40306AH
FUSE LABEL(2A STEP ILLUMI)
FUSE CASE(Clean with isopropyl alcohol.)
DOOR SILL TRIM HARNESS
24. Attach the fuse label to the door sill trim harness fuse case.
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
Without Other Accessory Harness 8-pin Connector
25. Plug the door sill trim harness 8-pin connector into the fuse box. Go to step 27.
QD40307AH
Plug in here.
DOOR SILL TRIM HARNESS 8-PIN CONNECTOR
FUSE BOX
FRONT VIEW
FUSE BOX
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
With Other Accessory Harness 8-pin Connector
26. If another accessory harness 8-pin connector is plugged into the fuse box, remove and discard the dummy connector from other accessory harness 8-pin connector, and plug the door sill trim harness 8-pin connector into other accessory harness 8-pin connector.
QD40308AH
FUSE BOXFRONT VIEW
OTHER ACCESSORY HARNESS 8-PIN CONNECTOR
DUMMY CONNECTOR (if equipped: Do not reuse.)
OTHER ACCESSORY HARNESS 8-PIN CONNECTOR
DOOR SILL TRIM HARNESS 8-PIN CONNECTOR
27. Secure the door sill trim harness to the vehicle harness with three wire ties.
QD40309AH
VEHICLE HARNESS
DOOR SILL TRIM HARNESS
3 WIRE TIES
2 (1707) 9 of 16
28. Route the door sill trim harness as shown.
QD40310AHDOOR SILL TRIM HARNESS
29. Align the green tape on the door sill trim harness with the vehicle clip, and secure the door sill trim harness to the vehicle harness with two wire ties.
QD40311AH
2 WIRE TIES
VEHICLE HARNESS
DOOR SILL TRIM HARNESS
VEHICLE CLIP
GREEN TAPE
10 of 16 AII07065-0
30. Secure the door sill trim harness to the vehicle harness with three wire ties.
QD40312AH
3 WIRE TIES
DOOR SILL TRIM HARNESS
VEHICLE HARNESS
31. Route the door sill trim harness as shown. Secure the door sill trim harness to the vehicle harness with three wire ties.
QD40313AH3 WIRE TIES
VEHICLE HARNESS
DOOR SILL TRIM HARNESS
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
32. Secure the door sill trim harness to the vehicle harness with one wire tie.
QD40314AH
WIRE TIE
VEHICLE HARNESS
DOOR SILL TRIM HARNESS
33. Using scissors, cut the protective tape at the measurements shown.
QC32315AH
30 mm (1.2 in.)
40 mm (1.6 in.)
40 mm (1.6 in.)
PROTECTIVE TAPE
30 mm (1.2 in.)
30 mm (1.2 in.)
A
A
B
B
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
34. Position the right front illuminated door sill trim at the masking tape.
QD40315AH
RIGHT FRONT ILLUMINATED DOOR SILL TRIM
MASKING TAPE
VEHICLE PANEL
PASSENGER’S SEAT
35. Using a felt-tip pen, mark the door opening seal and vehicle panel as shown.
QD40316AH
RIGHT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
DOOR OPENING SEAL MARK
FRONT MARK
MARK
VEHICLE PANEL
FELT-TIP PEN
36. Remove the right front illuminated door sill trim.
2 (1707) 11 of 16
37. Using a utility knife, cut out the door opening seal at the measurements shown.
QD40317AH
DOOR OPENING SEAL MARK
FRONT
Cut out.
SECTION VIEW
Cut out.
UTILITY KNIFE
15 mm(0.6 in.)
5 mm(0.2 in.)
3 mm(0.1 in.)
DOOR OPENING SEAL
12 of 16 AII07065-0
38. Using needle nose pliers, remove three steel wires from the door opening seal.
QD40318AH
DOOR OPENING SEAL
FRONT
SECTION VIEW
STEEL WIRE(Pull out.)
3 STEEL WIRES
NEEDLE NOSE PLIERS
DOOR OPENING SEAL
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
39. Using isopropyl alcohol on a shop towel, clean the vehicle panel where the protective tape will attach. Attach one piece of protective tape A to the vehicle panel.
QD40319AH
PROTECTIVE TAPE A
FRONT
MARK
PROTECTIVE CLIP
VEHICLE PANEL(Clean with isopropyl alcohol.)
40. Install the protective clip to the protective tape A.
41. Peel back the ends of two adhesive backings on the right front illuminated door sill trim and attach them to the front of the trim with masking tape.
QD40320AH
2 ADHESIVE BACKINGS(Peel back.)
MASKING TAPE
RIGHT FRONT ILLUMINATED DOOR SILL TRIM
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
42. Using an alcohol swab, clean the vehicle panel where the right front illuminated door sill trim will attach.
QD40321AH
VEHICLE PANEL(Clean with an alcohol swab.)
RIGHT FRONT ILLUMINATED DOOR SILL TRIM
MASKING TAPE
43. Position the right front illuminated door sill trim at the masking tape.
44. Attach the right front illuminated door sill trim to the vehicle panel by removing the two adhesive backings and pressing on the trim firmly with your hands.
QD40322AH2 ADHESIVE BACKINGS (Remove.)
MASKING TAPE (Remove.)
RIGHT FRONT ILLUMINATED DOOR SILL TRIM
45. Remove the masking tape.
2 (1707) 13 of 16
46. Route the right front illuminated door sill trim harness over the protective clip as shown.
QD40323AH
PROTECTIVE TAPE B
PROTECTIVE CLIP
RIGHT CENTER PILLAR LOWER TRIM(Raise if necessary.)
FRONT
RIGHT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
PROTECTIVE TAPE A
14 of 16 AII07065-0
47. Attach the one piece of protective tape B to the protective clip.
48. Repeat steps 34 through 47 to install the left front illuminated door sill trim.
49. Plug the door sill trim harness 2-pin connector into the left front illuminated door sill trim harness 2-pin connector.
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
VEHICLE HARNESS
2-PIN CONNECTORS
VEHICLE PANEL
Do not clamp the fuel fill door opener cable.
2-PIN CONNECTORS
WIRE TIE
VEHICLE HARNESS
SECTION VIEW WIRE
TIE
50. Secure the 2-pin connectors to the vehicle harness with one wire tie.
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
51. Secure the left front illuminated door sill trim harness to the vehicle harness with three wire ties.
VEHICLE HARNESS
3 WIRE TIES
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
WIRE TIE
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL
SECTION VIEW
VEHICLE HARNESS
52. Plug the door sill trim harness 2-pin connector into the right front illuminated door sill trim harness 2-pin connector.
QD40326AH
DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
RIGHT FRONT ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
VEHICLE PANEL
2-PIN CONNECTORS
Do not clamp the washer tube.
WIRE TIE
VEHICLE HARNESS
VEHICLE HARNESS
WIRE TIE
SECTION VIEW
53. Secure the 2-pin connectors to the vehicle harness with one wire tie.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII07065-0
54. Secure the right front illuminated door sill trim harness to the vehicle harness with three wire ties.
VEHICLE HARNESS
3 WIRE TIES
RIGHT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
WIRE TIE
RIGHT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL
SECTION VIEW
VEHICLE HARNESS
55. Pull away the door opening seal, and attach masking tape to the vehicle panel at the measurement shown.
QD40328AH
3 mm (0.1 in.)
MASKING TAPE
VEHICLE PANEL
RIGHT CENTER PILLAR LOWER TRIM
RIGHT REAR DOOR SILL TRIM
MASKING TAPE
DOOR OPENING SEAL(Pull away.)
2 (1707) 15 of 16
56. Peel back the ends of two adhesive backings on the right rear door sill trim and attach them to the front of the trim with masking tape. Remove one adhesive backing. NOTE: Check the identification mark of the right rear door sill trim.
QD40329AH
2 ADHESIVE BACKINGS(Peel back.)
MASKING TAPE
RIGHT REAR DOOR SILL TRIM(Identification mark: R)
ADHESIVE BACKING(Remove.)
57. Using an alcohol swab, clean the vehicle panel where the right rear door sill trim will attach.
QD40330AHVEHICLE PANEL(Clean with an alcohol swab.)
MASKING TAPE
RIGHT REAR DOOR SILL TRIM
58. Position the right rear door sill trim at the masking tape.
16 of 16 AII07065-0
59. Attach the right rear door sill trim to the vehicle panel by removing the two adhesive backings and pressing on the trim firmly with your hands.
2 ADHESIVE BACKINGS (Remove.)
MASKING TAPE (Remove.)
RIGHT REAR DOOR SILL TRIM
60. Remove the masking tape.
61. Repeat steps 55 through 60 to install the left rear door sill trim on the left side of the vehicle.
62. Check that all wire harnesses are routed properly and all connectors are plugged in.
63. Install all removed parts.
64. Connect the negative cable to the battery.
65. Turn the engine switch to ON; the SRS indicator should come on for about 6 seconds and then go off.
66. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions.
67. Set the clock on vehicles without navigation.
68. If necessary restore the systems back to normal operation as described in the service information.
Check the Operation of the Front Illuminated Door Sill Trim
69. Make sure the light comes on when you open each front door.
2 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.