Installation Guide - Vantec · 2017-12-05 · 4. Insert the hard drive caddy back into the NexStar...
2
Installation Guide Enclosure for 2.5” 7/9.5mm SATA 6Gbps SSD/HDD Copyright © 2016 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies. Information in this document is subject to change without notice. Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden. Printed in China Printed on Recycled Paper. v1.01 NST-228S3-BK www.vantecusa.com 4. Insert the hard drive caddy back into the NexStar TX housing as the picture show. Be sure to align the caddy with the guides within the housing. 3. Carefully connect the 2.5” hard drive to the connector. 2. Parts Layout. SATA/Power Connector USB 3.0 LED 1. Verify the package contents. USB Cable 5. Secure the caddy to the housing using the screws provided. USB Cable 6. Connect the USB cable. (Power will be drawn from the USB port and provide power to the hard drive) 7A. If you install a new drive, proceed with the necessary setup procedure to initialize, partition and format the new hard drive using the OS tool. 7B. If you install a drive with exsiting data, you should be able to use the OS file manager to see your data. tape rubber here to cushion drive when inserted Peel off white tape, secure the translucent plastic sheet on the printed circuit side of the hard drive.
Transcript of Installation Guide - Vantec · 2017-12-05 · 4. Insert the hard drive caddy back into the NexStar...
Installation GuideEnclosure for 2.5” 7/9.5mm SATA 6Gbps SSD/HDD
Copyright © 2016 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies.
Information in this document is subject to change without notice.Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.
Printed in ChinaPrinted on Recycled Paper.
v1.01 NST-228S3-BK
www.vantecusa.com
4. Insert the hard drive caddy back into the NexStar TX housing as the picture show. Be sure to align the caddy with the guides within the housing.
3. Carefully connect the 2.5” hard drive to the connector.
2. Parts Layout.
SATA/Power Connector
USB 3.0
LED
1. Verify the package contents.
USB Cable
5. Secure the caddy to the housing using the screws provided.
USB Cable
6. Connect the USB cable. (Power will be drawn from the USB port and provide power to the hard drive)
7A. If you install a new drive, proceed with the necessary setup procedure to initialize, partition and format the new hard drive using the OS tool.
7B. If you install a drive with exsiting data, you should be able to use the OS �le manager to see your data.
tape rubberhere to cushiondrive when inserted
Peel off white tape, secure the translucent plastic sheet on the printed circuit side of the hard drive.
![VOLKSWAGEN CADDY, CADDY MAXI [2004-2015] VOLKSWAGEN CADDY, CADDY … · 43062 • 1.1 • 08/07/2015 2 43062 volkswagen caddy, caddy maxi eco fuel, 4 motion volkswagen caddy, caddy](https://static.fdocuments.in/doc/165x107/60f989e18ccff15ba348ac77/volkswagen-caddy-caddy-maxi-2004-2015-volkswagen-caddy-caddy-43062-a-11-a.jpg)
![USER MANUALstatic.highspeedbackbone.net/pdf/Vantec NexStar 3...4) After the needed files are copied into your system, click on [Finish]. 5) You should now be able to see the new hard](https://static.fdocuments.in/doc/165x107/601caf1a28ed9760e434426a/user-nexstar-3-4-after-the-needed-files-are-copied-into-your-system-click-on.jpg)
