INSTALLATION 201 INSTRUCTIONS 2-DOOR 2014 · © 2014 American Honda Motor Co., Inc. – All Rights...
Transcript of INSTALLATION 201 INSTRUCTIONS 2-DOOR 2014 · © 2014 American Honda Motor Co., Inc. – All Rights...
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2014 American Honda Motor Co., Inc. – All Rights Res
VERSION 1
FOG LIGHTServed. AII 52270 (1409)
2015 CIVIC2-DOOR
08V31-TS8-1000-
Issue Date
SEPT 2014
PARTS LISTFog Light KitP/N 08V31-TS8-100E (non-auto light/non-BSM)P/N 08V31-TS8-100F (non-auto light/BSM)P/N 08V31-TS8-100G (auto light/non-BSM)P/N 08V31-TS8-100H (auto light/BSM)
Right fog light
Left fog light
Right fog light trim
Left fog light trim
Switch harness
Fog light harness
Combination light switch
6 Self-tapping screws, 5 x 14 mm
Relay
20A Fuse (May not used)
Fuse label (May not used)
Clip A
9 Wire ties
2 Aluminum tapes
Relay bracket
Clip B
1 of 1992
Wire tie with clip
Right fog light cover
Left fog light cover
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverDiagonal cutters10 mm SocketIsopropyl alcoholShop towelTape RatchetScissorsSmall flat-tip screwdriverBlanketThe following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Fog Lights Installed in the Vehicle
QC70101AT
RIGHT FOG LIGHT
LEFT FOG LIGHT
FOG LIGHT HARNESS
COMBINATION LIGHT SWITCH
SWITCH HARNESS
2 of 19 AII 52270 (14
INSTALLATION
1. Disconnect the negative cable from the battery.
2. Remove the trunk lid/fuel fill door opener cover (four retaining tabs and two hooks). Remove one self-tapping screw. Using the key, unlock the trunk opener.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
Q072052AK
KEY
Unlock.
TRUNK LID/FUEL FILL DOOR OPENER COVER
4 RETAINING TABS
SELF-TAPPING SCREW
2 HOOKS
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
3. Release the driver’s front door sill trim (seven clips, one hook, and two retaining tabs).
4. Pull away the door opening seal, and remove the driver’s kick panel (two clips).
Q090701AK
7 CLIPS
Raise.HOOK
FRONT
DRIVER’S FRONT DOOR SILL TRIM
2 RETAINING TABS
Q072050AK
DOOR OPENING SEAL(Pull away.)
CLIP
DRIVER’S KICK PANEL
CLIP
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
5. Remove the driver’s dashboard lower cover (nine clips and unplug the vehicle connector, if equipped).
6. Lower the tilt lever, and turn the steering wheel 90° counterclockwise.
7. Using a plastic trim tool, release the lock tab as shown.
Q072055AK
VEHICLE CONNECTOR(if equipped)
9 CLIPS DRIVER’S DASHBOARD LOWER COVER
Q082304BK
STEERING WHEEL
PLASTIC TRIM TOOL
UPPER COLUMN COVER
09) 3 of 19
8. Turn the steering wheel 180° clockwise.
9. Using a plastic trim tool, release the lock tab on the other side the same way.
10. Remove the upper column cover (four hooks).
Q0D1402AH
UPPER COLUMN COVER
PLASTIC TRIM TOOL
PLASTIC TRIM TOOL
Q082307AK
4 HOOKSUPPER COLUMN COVER
4 of 19 AII 52270 (14
11. Remove two self-tapping screws from the lower column cover.
12. Remove the lower column cover (one self-tapping screw).
Q082310AK
LOWER COLUMN COVER
2 SELF-TAPPING SCREWS
Q082311AK
LOWER COLUMN COVER
SELF-TAPPING SCREW
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
13. Remove the front bumper:• On each side, attach tape to the areas shown.• Wrap a shop towel around the hood latch.
QC61601ATTAPE FRONT
BUMPER
HEADLIGHT
HOOD LATCH(Wrap with a shop towel.)
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
• Remove the 4 self-tapping screws, 10 clips, and 2 bolts.
• On each side, release two retaining tabs.
QC61602BT
2 SELF-TAPPINGSCREWS(round head)
10 CLIPS
2 SELF-TAPPING SCREWS(flat head)
2 BOLTS
QC61603AT
2 RETAINING TABS
FRONT BUMPER
09) 5 of 19
• On each side, release four retaining tabs.
• With the help of an assistant, remove the front bumper (four clips). Place the front bumper on a blanket to prevent damage.
QC61604AT
4 RETAININGTABS
FRONT BUMPER
21
QC70131AT
4 CLIPS
FRONT BUMPER
HOOKHOOK
6 of 19 AII 52270 (14
14. Remove the six clips from the right front inner fender and pull back the right inner fender as shown.
15. Remove the front bumper absorber (two hooks).
Q0D1301AH
RIGHT HEADLIGHT
6 CLIPS
RIGHT INNER FENDER(Pull back.)
FRONT RIGHT TIRE
QC70102AT
2 HOOKS
BUMPER BEAM
FRONT BUMPER ABSORBER
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
Installing the Fog Lights
16. Remove the left bumper trim from the front bumper (10 retaining tabs and 1 clip).
17. Install the new left fog light trim to the front bumper with 10 retaining tabs and 1 clip.
QC70103BT
FRONT BUMPER
LEFT BUMPER TRIM(Discard.)
10 RETAINING TABS
CLIP
QC70129BT
10 RETAINING TABS
FRONT BUMPER
NEW LEFT FOGLIGHT TRIM CLIP
(reused)
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
18. Secure the left fog light to the left fog light trim with three 5 x 14 mm self-tapping screws.
19. Install the left fog light cover to the left fog light trim with one 5 x 20 mm self-tapping screw and five retaining tabs.
20. Repeat steps 16 through 19 to install the fog light trim on the right side of the vehicle.
QC70104AT
3 SELF-TAPPING SCREWS, 5 x 14 mm
LEFT FOG LIGHT TRIM
LEFT FOG LIGHT
QC70106AT
LEFT FOG LIGHT TRIM
LEFT FOG LIGHT COVER
5 RETAINING TABS
5 x 20 mmSELF-TAPPING
09) 7 of 19
Routing the Fog Light Harness
21. Get the fog light harness. Route the fog light harness under the right headlight and secure the fog light harness clips to the holes in the extension and vehicle panel as shown.
QC70107BT
DUAL EXTENSION
FOG LIGHT HARNESS CLIP
FRONT
RIGHT HEADLIGHT
FOG LIGHT HARNESS
EXTENSION
FRONT
FOG LIGHT HARNESS CLIP
VEHICLE PANEL
8 of 19 AII 52270 (14
22. Locate the vehicle 1-pin connector blue-taped to the vehicle harness. Remove the blue tape to free the vehicle 1-pin connector.
23. Plug the fog light harness 1-pin connector into the vehicle 1-pin connector as shown.
QB52811AH
FOG LIGHT HARNESSVEHICLE 1-PIN
CONNECTOR
BLUE TAPE
FOG LIGHT HARNESS 1-PIN CONNECTOR
FRONT
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
24. Remove three bolts and one clip from the washer tank. Move the washer tank out of the way in the direction shown.
25. Remove the vehicle ground bolt. Attach the fog light harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt.
QB52812AH
HOOKRIGHT HEADLIGHT
3 BOLTS
WASHER TANK
CLIP
QB52813AH
FOG LIGHT HARNESS GROUND
TERMINAL
VEHICLE GROUND BOLT(reused)
VEHICLE GROUND TERMINAL
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
26. Reinstall the washer tank.
27. Secure the fog light harness to the vehicle harness with two wire ties. Do not secure the fog light harness to the washer tube.
QB52814AH
WASHER TANK
CLIP
QB52815AH
VEHICLE HARNESS
2 WIRE TIES
FOG LIGHT HARNESS
09) 9 of 19
28. Secure the fog light harness to the vehicle harness with two wire ties as shown. Do not secure the fog light harness to the SRS harness.
29. Under the washer tank, secure the fog light harness to the vehicle harness with one wire tie as shown. Do not secure the fog light harness to the SRS harness.
With Vehicle Harness
QB52816AHWIRE TIE
VEHICLE HARNESS
Do not secure to the SRS harness.FOG LIGHT
HARNESS
WIRE TIE
WASHER TANK
Do notsecure tothe SRSharness.
QB52817AH
FOG LIGHT HARNESS
RIGHT HEADLIGHT
FOG LIGHT HARNESS
Do not secure to the SRS harness.
WIRE TIE
VEHICLE HARNESS
WASHER TANK
10 of 19 AII 52270 (14
30. Using diagonal cutters, cut the clip portion off of one wire tie with clip.
31. Secure the fog light harness to the vehicle harness with one wire tie with clip.Go to step 33.
QC70108CT
DIAGONAL CUTTERS
VEHICLECLIP
WIRE TIEWITH CLIP
FOG LIGHT HARNESS VEHICLE
HARNESS
Cut off. Do notsecure tothe SRSharness.
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
Without Vehicle Harness
32. Attach one wire tie with clip on the fog light harness and secure the fog light harness to the hole in the vehicle panel with the clip.
33. Route the fog light harness along the bumper beam as shown.
QC70109CT
VEHICLEHOLE
VEHICLE HARNESS
Do not secure to the SRS harness.
WIRE TIEWITH CLIP
FOG LIGHTHARNESS
FOG LIGHTHARNESS
QC70110AT
BUMPER BEAM FOG LIGHT
HARNESS
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
34. Secure the fog light harness clip to the hole in the extension as shown.
35. Using isopropyl alcohol on a shop towel, clean the bumper beam where the aluminum tapes will attach.
36. Using scissors, cut two aluminum tapes in half.37. Secure the fog light harness to the bumper beam
with the four pieces of aluminum tape in the areas shown.
QC70111AT
FRONT
FOG LIGHT HARNESS CLIP
DUAL EXTENSION
EXTENSION
QC70112AT
2 ALUMINUM TAPES(Cut.)
Clean with isopropyl alcohol.
BUMPER BEAM
4 ALUMINUM TAPES
09) 11 of 19
38. Reinstall the front bumper absorber.
39. Plug the fog light harness 2-pin connector into each fog light, and with the help of an assistant, reinstall the front bumper.
QC70113AT
BUMPER BEAMFRONT BUMPER
ABSORBER
QC70114AT
FOG LIGHT HARNESS 2-PIN CONNECTOR
FRONT BUMPERLEFT FOG LIGHT
RIGHT FOG LIGHT
FOG LIGHTHARNESS2-PINCONNECTOR
12 of 19 AII 52270 (14
Routing the Switch Harness
40. Remove the clip holding the vehicle harness connectors to the vehicle panel.
41. Remove the vehicle harness connector from the vehicle harness 14-pin connector.Without another accessory connector
QC70115AT
CLIP
VEHICLE HARNESS CONNECTORS
HOOD OPENER
VEHICLE PANEL
QC70116AT
VEHICLE HARNESS 14-PIN CONNECTOR
VEHICLE HARNESS CONNECTOR
FRONT
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
With another accessory connector
42. Remove the clip from the vehicle harness 14-pin connector, and install clip B on the vehicle harness 14-pin connector.
QC70117AT
VEHICLE HARNESS 14-PIN CONNECTOR
VEHICLE HARNESS CONNECTOR
ANOTHER ACCESSORY CONNECTORS
QC70118AT
FRONT
VEHICLE HARNESS 14-PIN CONNECTOR
CLIP(Discard.)
CLIP B(supplied)
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
43. Unplug the vehicle harness 14-pin connector.
44. Release the retainer on the vehicle harness 14-pin connector. Connect the switch harness terminal into the vehicle harness 14-pin connector in the slot shown.
45. Replug the vehicle harness 14-pin connector and reinstall the 14-pin to its original position.
QC70119AT
VEHICLE HARNESS 14-PIN CONNECTOR
QC70120AT
RETAINER
VEHICLE HARNESS 14-PIN CONNECTOR
HARNESS SIDE VIEW
2 RETAINING TABS(Release.)
CONNECTING LOCATION
SWITCH HARNESS TERMINAL
RETAINER
09) 13 of 19
46. Remove the vehicle bolt from the hood opener.
47. Attach the relay bracket in the position shown, and reinstall the vehicle bolt.
48. Install clip A to the relay block of the switch harness.
QC70121AT
HOOD OPENER
VEHICLE BOLT(reused)
RELAY BRACKET
Align.
HOOD OPENER
Q080206AH
RELAY BLOCK
SWITCH HARNESS
CLIP A
14 of 19 AII 52270 (14
49. Install the relay to the switch harness relay block.
50. Secure the switch harness relay block to the relay bracket.
Q080207AH
RELAY
RELAY BLOCK
SWITCH HARNESS
QC70122AT
RELAY BRACKET
RELAY BLOCK(with clip A)
SWITCH HARNESS
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
51. Plug the switch harness 4-pin connector and 6-pin connector into the fuse box. Go to step 54.
With Another Accessory Harness Connector
52. If the 6-pin connector is already used by another accessory, locate the 6-pin connector taped on another accessory harness. Remove the dummy connector from another accessory harness. Plug the switch harness 6-pin connector into another accessory harness 6-pin connector. Go to step 54.
Q080209AH
4-PIN CONNECTOR FUSE
BOX
4-PIN CONNECTOR
6-PIN CONNECTOR
SWITCH HARNESS
6-PIN CONNECTOR
Q0D1310AH
4-PIN CONNECTOR 6-PIN
CONNECTOR
DUMMY CONNECTOR(Discard.)
4-PIN CONNECTOR
SWITCH HARNESS
ANOTHER ACCESSORY HARNESS 6-PIN CONNECTOR
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
53. If the 4-pin connector is already used by another accessory, locate the 4-pin connector taped on another accessory harness. Plug the switch harness 4-pin connector into another accessory harness 4-pin connector.
54. Secure the switch harness to the vehicle harness with two wire ties.
Q0D1309AH
4-PIN CONNECTOR
SWITCH HARNESS 6-PIN
CONNECTOR
6-PIN CONNECTOR
ANOTHER ACCESSORY HARNESS 4-PIN CONNECTOR
QC70123ATVEHICLE HARNESS
2 WIRE TIES
SWITCH HARNESS
HOOD OPENER
09) 15 of 19
55. Secure the switch harness to the vehicle harness with two wire ties.
56. Unplug the vehicle connector from the combination light switch.
57. While pushing the two retaining tabs, slide the combination light switch out and remove it from the steering column. NOTE: Do not pull on the lever when removing the switch.
Q080211AH
2 WIRE TIES
VEHICLE HARNESS
SWITCH HARNESS
Q080212CH
COMBINATION LIGHT SWITCH(Discard.)
2 RETAINING TABS(Push.)
VEHICLE CONNECTOR
STEERING COLUMN STEERING WHEEL
Do not pull on the lever.
16 of 19 AII 52270 (14
58. Install the new combination light switch to the steering column. NOTE: Do not push on the lever when installing the switch.
59. Plug the vehicle connector to the new combination light switch.
If a fuse is already installed in the fuse box: go to step 63, otherwise continue with step 60.
60. Plug the 20A fuse into the fuse box.
Q080213CH
NEW COMBINATION LIGHT SWITCH
VEHICLE CONNECTOR
STEERING COLUMN STEERING WHEEL
2 RETAINING TABS(Push.)
Do not push on the lever.
Q0D1311AH
FUSE BOX
CONNECTING LOCATION
20A FUSE
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
61. Using isopropyl alcohol on a shop towel, clean the driver’s kick panel where the fuse label will attach.
62. Attach the fuse label to the driver’s kick panel.
63. Check that all wire harnesses are routed properly and all connectors are plugged in.
64. Reinstall all removed parts.65. Reconnect the negative cable to the battery and
check operation of all lights and other electrical accessories.
66. Press and hold the radio power button for two seconds to restore radio and navi (if equipped) system functions.
67. Reset the clock.68. Restore the systems back to normal operation as
described in the Service Manual if necessary.
Q0D1312AH
Clean with isopropyl alcohol.
FUSE LABEL(20A OPTION FUSE)
ATTACHING LOCATION
DRIVER’S KICK PANEL
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
USE AND CARE
How to Operate the Fog Lights
• Turn the headlight switch to the “ ” position (headlights on low beam).
• Turn the fog light switch on (indicator is on).
NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.• If the fog lights do not turn on, check the fuse and all the
connectors, including the ground cable.
Q0D2101AH
FOG
LIG
HT
SWIT
CH
HEADLIGHT SWITCH
Low HighOFF
OFF -
ON
- - -
- - -
The auto light model is shown.
09) 17 of 19
Fog Light Aiming Adjustment
69. Adjust the fog light:• Adjust the aim according to your local laws and
regulations.• To adjust, turn the adjustment screw in or out
until the correct aim is obtained.
BULB REPLACEMENT1. Remove the fog light cover (one 5 x 20 mm self-
tapping screw and five retaining tabs).
QC70124AT
AIMING ADJUSTMENT SCREW
To lower. To raise.
AIMING ADJUSTMENT SCREW
FOG LIGHT
QC70106AT
SELF-TAPPING SCREW, 5 x 20 mm
FOG LIGHT TRIM
FOG LIGHT COVER
5 RETAINING TABS
18 of 19 AII 52270 (14
2. Remove the fog light (three self-tapping screws and unplug the vehicle connector).
3. Remove the bulb from the fog light as shown.
QC70125AT
RETAINING TAB(Push.)
Pull.VEHICLE CONNECTOR
3 SELF-TAPPING SCREWSFOG LIGHT
QC70126AT
BULB(Turn.)
FOG LIGHT
09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
4. Install the new bulb to the fog light.• Use only a genuine Honda halogen light bulb of
specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003
• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.
• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may annoy the oncoming driver’s view.
5. Reinstall the fog light.
QC70127AT
Turn the bulb until it stops.
FOG LIGHT
NEW BULB
NEW BULB
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14
• Check that the wire harness is not pinched.• Be sure to tighten the self-tapping screws
securely.
6. Install the fog light cover to the fog light trim with one 5 x 20 mm self-tapping screw and five retaining tabs.
7. Check the operation of the fog light; readjust the aim if necessary.
QC70128AT
VEHICLE CONNECTOR
FOG LIGHT3 SELF-TAPPING SCREWS
QC70106AT
5 x 20 mmSELF-TAPPING SCREW
FOG LIGHT TRIM
FOG LIGHTCOVER
5 RETAINING TABS
09) 19 of 19