instalar lasercut
-
Upload
carlos-gomez-linares -
Category
Documents
-
view
238 -
download
0
Transcript of instalar lasercut
-
7/31/2019 instalar lasercut
1/99
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface. Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
-
7/31/2019 instalar lasercut
2/99
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. Theprovided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
-
7/31/2019 instalar lasercut
3/99
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
-
7/31/2019 instalar lasercut
4/99
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
-
7/31/2019 instalar lasercut
5/99
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog andUSB laser interface.
-
7/31/2019 instalar lasercut
6/99
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
-
7/31/2019 instalar lasercut
7/99
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successfulinstallations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
-
7/31/2019 instalar lasercut
8/99
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog andUSB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also beinstalled from a USB dongle, Network Drive, or
-
7/31/2019 instalar lasercut
9/99
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain anysoftware for the user. Do not insert the dongle yet.
-
7/31/2019 instalar lasercut
10/99
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
-
7/31/2019 instalar lasercut
11/99
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also beinstalled from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-9060SE\20081224\install\Setup.exe
-
7/31/2019 instalar lasercut
12/99
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain anysoftware for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
-
7/31/2019 instalar lasercut
13/99
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain anysoftware for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
-
7/31/2019 instalar lasercut
14/99
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
-
7/31/2019 instalar lasercut
15/99
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the defaultdirectories. Do NOT use the Chinese version.
-
7/31/2019 instalar lasercut
16/99
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installationapplication from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
-
7/31/2019 instalar lasercut
17/99
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successfulinstallations have been done by copying all the
-
7/31/2019 instalar lasercut
18/99
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the defaultdirectories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. Theprovided CD should be labeled as HX-9060 Laser 4.1.2.0
-
7/31/2019 instalar lasercut
19/99
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
-
7/31/2019 instalar lasercut
20/99
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
-
7/31/2019 instalar lasercut
21/99
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. Theprovided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
-
7/31/2019 instalar lasercut
22/99
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
-
7/31/2019 instalar lasercut
23/99
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
-
7/31/2019 instalar lasercut
24/99
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog andUSB laser interface.
-
7/31/2019 instalar lasercut
25/99
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
-
7/31/2019 instalar lasercut
26/99
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successfulinstallations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
-
7/31/2019 instalar lasercut
27/99
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog andUSB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also beinstalled from a USB dongle, Network Drive, or
-
7/31/2019 instalar lasercut
28/99
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain anysoftware for the user. Do not insert the dongle yet.
-
7/31/2019 instalar lasercut
29/99
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
-
7/31/2019 instalar lasercut
30/99
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also beinstalled from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-9060SE\20081224\install\Setup.exe
-
7/31/2019 instalar lasercut
31/99
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain anysoftware for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
-
7/31/2019 instalar lasercut
32/99
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain anysoftware for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
-
7/31/2019 instalar lasercut
33/99
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
-
7/31/2019 instalar lasercut
34/99
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the defaultdirectories. Do NOT use the Chinese version.
-
7/31/2019 instalar lasercut
35/99
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installationapplication from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
-
7/31/2019 instalar lasercut
36/99
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successfulinstallations have been done by copying all the
-
7/31/2019 instalar lasercut
37/99
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the defaultdirectories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. Theprovided CD should be labeled as HX-9060 Laser 4.1.2.0
-
7/31/2019 instalar lasercut
38/99
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
-
7/31/2019 instalar lasercut
39/99
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
-
7/31/2019 instalar lasercut
40/99
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. Theprovided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
-
7/31/2019 instalar lasercut
41/99
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
-
7/31/2019 instalar lasercut
42/99
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-install the drivers for the soft-dog and
USB laser interface.
Installing the LaserCut 5.3 Software
The USB Dongle is the software license key only. It does NOT contain any
software for the user. Do not insert the dongle yet.
Find the CD containing your LaserCut 5.3 installation application. The
provided CD should be labeled as HX-9060 Laser 4.1.2.0
Place the CD into the CD drive of your computer. The software can also be
installed from a USB dongle, Network Drive, or
any other resource accessible from the new computer. The most successful
installations have been done by copying all the
installation files to the local hard drive and then running the installation
application from the local hard drive.
Navigate the My Computer window to your installation files as shown here.
The installation file is located at \english-
9060SE\20081224\install\Setup.exe
Run the Setup.exe application
Answer all the questions for the software installation .. Please use the default
directories. Do NOT use the Chinese version.
The program will copy the files and re-insta