Information provided in this booklet was correct as at 16 ... Systems... · Information provided in...

Information provided in this booklet was correct as at 16th November 2017.

For the latest ROCKCOTE Systems Guide and product information, visit the ROCKCOTE website:

http://www.rockcote.com.au





2 ROCKCOTE Systems Guide | www.rockcote.com.au

ROCKCOTE Systems Guide | www.rockcote.com.au 3

This booklet is designed to help you choose which ROCKCOTE Render System is the right one for

you, with consideration given to substrate, situation and finish. It is designed to be used as a guide.

If you should need any further help, please do not hesitate to contact ROCKCOTE Head Office on

1300 736 668 or email at [email protected].

_________________________________________________________________________________________________

This document is comprised of two sections:

SECTION 1 – ROCKCOTE Systems Guide (first 40 pages) SECTION 2 – ROCKCOTE Natural Materials Systems Guide (last 20 pages)_________________________________________________________________________________________________

Contents

ROCKCOTE Systems Guide ................................................................................................................................................ 4

Common Substrate Brand Names Chart ............................................................................................................................ 5

Common Substrates ............................................................................................................................................................ 8

Brick & Block ..................................................................................................................................................................... 8

Off-Form Concrete .......................................................................................................................................................... 10

Off-Form Concrete Ceilings & Soffits .............................................................................................................................. 12

Tilt-up Pre-cast Concrete Panel ...................................................................................................................................... 13

Expanded Polystyrene (EPS).......................................................................................................................................... 15

ROCKCOTE Reinforced Render Systems (RRR) ........................................................................................................... 15

AAC Panel (75mm) ......................................................................................................................................................... 17

AAC Panel (50mm) ......................................................................................................................................................... 19

Blueboard Fibre Cement Sheeting .................................................................................................................................. 21

Core Filled Fibre Cement AFS ........................................................................................................................................ 23

Core Filled Fibre Cement RITEK .................................................................................................................................... 25

Extruded Polystyrene (XPS) Including Foamular Metric & Isoboard ............................................................................... 27

Pre-Meshed EPS ............................................................................................................................................................ 29

Site Mix (Sand & Cement) Render .................................................................................................................................. 31

Previously Painted/Coated Masonry ............................................................................................................................... 33

Paint & Texture Systems Over Flat Previously Painted/Coated Masonry ....................................................................... 34

Magnesium Board (MGO) ............................................................................................................................................... 35

ROCKCOTE Paint Systems Guide .................................................................................................................................... 37

ROCKCOTE EcoStyle ......................................................................................................................................................... 38

EcoStyle Over Plasterboard Walls .................................................................................................................................. 38

EcoStyle Over Fibro Walls .............................................................................................................................................. 38

EcoStyle Ceiling White Over Plasterboard Ceilings ........................................................................................................ 39

EcoStyle Ceiling White Over Fibro Ceilings .................................................................................................................... 39

EcoStyle Over Timber ..................................................................................................................................................... 40

EcoStyle Over Previously Painted Surfaces ................................................................................................................... 40

Solar Protect ................................................................................................................................................................... 41

Natural Materials .............................................................................................................................................................43

mailto:[email protected]


ROCKCOTE Systems Guide

The question of “which system best suits the purpose” is dependant upon a number of factors: 1. Location2. Environment3. Substrate4. Construction Type (Residential, Commercial or High Rise)

WARRANTY KEY FEATURES

Up to 15 Year Warranty Available *

ROCKCOTE Premium High Performance Membrane Systems

Most durable

Greatest flexibility (crack resistance)

Lowest maintenance

Highest level of water repellence

High resistance to dirt and mould

Vapour permeable

Up to 15 Year Warranty Available *

ROCKCOTE Coloured Render Systems

Stylish, long life coatings with attractive coloured finishes

Pigmented trowel-on, no paint required

Flexible and crack resistant

Water repellent

Low maintenance

Vapour permeable

10 Year Warranty *

ROCKCOTE Premium High Performance Membranes (Standard)

Flexible and crack resistant

Water repellent

Resistance to dirt and mould

Low maintenance

Vapour permeable

7.5 Year Warranty *

ROCKCOTE Matte Finishes

Stylish Mediterranean aesthetics achieved

High build roll-on coatings for economical matte finishes

May require general maintenance

Vapour permeable

ROCKCOTE recommends that you always contact us to confirm the most suitable ROCKCOTE system for your project. System must also adhere to the ROCKCOTE Maintenance Guide in order to be eligible for warranty. Http://www.rockcote.com.au/sites/default/files/ROCKCOTE%20Maintenance%20Guide.pdf.

ROCKCOTE reserves the right to change any of the above information at any time without notice.

INDEMNITY ROCKCOTE Enterprises Pty Ltd will not accept responsibility for any misuse of this product or if not applied by a skilled and experienced applicator and in accordance with our technical specifications. Due to our policy of continuing product improvement ROCKCOTE Enterprises Pty Ltd reserves the right to change these specifications without further notice.

http://www.rockcote.com.au/sites/default/files/ROCKCOTE%20Maintenance%20Guide.pdf


Common Substrate Brand Names Chart

PLEASE NOTE: SUBSTRATES MUST ALWAYS BE INSTALLED STRICTLY

IN ACCORDANCE WITH MANUFACTURER SPECIFICATIONS.

BRAND NAME DESCRIPTION ROCKCOTE SYSTEM OPTIONS

AFS Concrete Filled Fibre Cement Sheet Panel System

Patch & Prep with mesh in joints then acrylic render or texture system

Patch & Prep with mesh in aluminium joints then Screedable Render System

Benex Block Composite Block Quick Render PM100 then optional coloured render/membranes

If laid smooth side out, Keycote, primer and coloured render with optional clears/ membrane

Blueboard 7.5mm Fibre Cement Texture Base Sheet


Brick/Block Standard Masonry Quick Render Range as Base Coat

Keycote to be considered if surface is smooth or highly absorbent.

Comtex 9mm Fibre Cement Texture Base Sheet

Patch & Prep with mesh in joints and corners, then acrylic render or texture system

EcoClad2010 Expanded Polystyrene ROCKCOTE Reinforced Render

Eco Block Expanded Polystyrene Block

ROCKCOTE Reinforced Render

Foamula Metric Extruded Polystyrene [XPS] Keycote then ROCKCOTE Reinforced Render

Formcraft Expanded Polystyrene Block


FC Sheeting 4-6mm Fibre CementSquare edged sheeting

Sealer Undercoat & two top coats of EcoStyle or Roll on Textures

AAC Block Autoclaved Aerated Concrete Panel [AAC]

50/50 Acrybond & water, then ROCKCOTE Reinforced Render System

50/50 water & Acrybond then two coats of coloured render, optional clears or membrane

AAC Panel 75mm Autoclaved Aerated Concrete Panel [AAC]

50/50 water & Acrybond then two coats of coloured render, optional clears or membrane

50/50 Acrybond & water, Quick Render Range then coloured render/ membranes

Insulclad EPS Plain Expanded Polystyrene ROCKCOTE Reinforced Render System

Insulclad Meshed Pre-Meshed Polystyrene Keycote then ROCKCOTE Reinforced Render

Isoboard Extruded Polystyrene [XPS] Keycote then ROCKCOTE Reinforced Render


BRAND NAME DESCRIPTION ROCKCOTE SYSTEM OPTIONS

Kool Wall, Master Wall

Pre-Meshed Polystyrene Keycote then ROCKCOTE Reinforced Render

Loxo 50mm Autoclaved Aerated Concrete Panel [AAC]

50/50 Acrybond & water, then ROCKCOTE Reinforced Render System

50/50 water & Acrybond, Quick Render PM100 with mesh then two coats of coloured render, optional clears or membrane

NPS Thermagold Expanded Polystyrene ROCKCOTE Reinforced Render System

NRG Green Board Expanded Polystyrene ROCKCOTE Reinforced Render

Off Form Concrete Concrete Walls/slabs formed in situ

Clean down, apply Keycote then render system

Patch joints with Smooth Patch and apply paint finishes

Previously Coated Brick/Block [Textured or Painted]

Rendered or textured Brick/Block & Masonry Surface

Keycote then Quick Render Range with coloured top coats

Keycote then optional coloured topcoats

Plasterboard Paper Faced Gypsum Board

Sealer Undercoat & two top coats of EcoStyle

PolyBlock Panel Expanded Polystyrene ROCKCOTE Reinforced Render

Previously Coated Masonry [Flat Surfaces]

Previously Rendered & Painted Brick/Block or Concrete Surfaces

Texprime, then Texture & Membrane Systems

Primer then Armour

Ritek Concrete Filled Fibre Cement Sheet Panel System

Patch & Prep with mesh in aluminium joints then acrylic render or texture system

Patch & Prep with mesh in aluminium joints then Screedable Render System

Styrocon Polyurethane Filled Fibre Cement Sheet Panel System


Keycote over entire surface meshing joints as you go then coloured render systems

INEX Board, Modak Magnesium Board

MGO Jointed Cladding Panel

Keycote over entire surface meshing joints as you go then coloured render systems

Render board, Keycote then RRR

Thermawall Plus Pre-Meshed Polystyrene Keycote then ROCKCOTE Reinforced Render

Thermawall Expanded Polystyrene ROCKCOTE Reinforced Render

Tilt Up Concrete Concrete Panels pre-made and stood up onsite

Clean down & apply Solprime then paint or trowel on finishes

If to be rendered over, seek technical advice

Villaboard Fibre Cement Sheet made interior

Sealer Undercoat & two top coats of EcoStyle

Zego Block Expanded Polystyrene Block



BRAND NAME PREPARATION ECOSTYLE ARMOUR RENDER PAINT

Axon Cladding Smooth Sanding Patch if screw fixed

Linea Weatherboard Etch Primer to Aluminium Joiners

Matrix Cladding Smooth Sanding Patch if screw fixed

Stria Cladding Smooth Sanding Patch if screw fixed

Easy Lap Etch Primer to Aluminium Joiners

Soffit Sheeting Smooth Sanding Patch if screw fixed

Hardie Flex Smooth Sanding Patch if screw fixed

Hardie Plank Smooth Sanding Patch if screw fixed

Hardie-Tex BLUEBOARD SYSTEMS

Durasheet Primer

DuraPlank Primer

Duratex (blueboard) BLUEBOARD SYSTEMS

Duralattice Primer

Duragroove

Durascape

Duragrid

Duracom

Nuline+Plus

Express Wall Primer

Texture Base Sheet BLUEBOARD SYSTEMS

Weather Boards Primer

Cladding Plank Primer

Cladding & Eaves Lining Primer

Soffit Line Primer

Architectural Columns Primer

Compressed Sheet (Walls) Patch Screw Holes, then Primer

NOTE: Anytime “ROCKCOTE Quick Render” is mentioned, any product from ROCKCOTE’s Quick Render range.


Common Substrates

BRICK & BLOCK _________________________________________________________________________________________________ Adhesion Requirements: If brick/blocks are smooth faced and have very little or excessive absorption rates, ROCKCOTE

Keycote must be used. Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.

Substrate must be wet down to assist with correct cement hydration and bonding. Application of ROCKCOTE Quick Render may proceed once the “shine” has gone off the wall. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: If total thickness of coating system is to exceed 10mm, and is to be less than 30mm, use Quick Render

PM100 High Build as a base coat prior to the application of Quick Render. For coating systems greater than 30mm, contact ROCKCOTE Technical Department. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

Premium High Performance Membrane Systems Up to 15 YEAR WARRANTY*

Finish required 1st Step 2nd Step 3rd Step 4th Step

Armoured Sponge Finish Quick Render Polymer Render Grey Armour Armour

Armoured Santa Fe Quick Render Santa Fe Armour Armour

Armoured Trowel-On Quick Render Trowel On Armour Armour

Armoured Acrylic Texture Fine Quick Render Acrylic Texture Fine 1mm DFT** Armour Armour

Armoured Acrylic Texture Medium or Coarse

Quick Render Acrylic Texture Medium or Coarse Armour Armour

Armoured Flexi Tex Medium

Quick Render Flexi Tex Medium Armour Armour

Coloured Render Systems Up to 15 YEAR WARRANTY*


Sandcote Quick Render Texprime (Tinted) Sandcote Clearcote/Repel

Sandcote HydroGuard Quick Render Texprime (Tinted) Sandcote HydroGuard

Pearlcote Quick Render Texprime (Tinted) Pearlcote Clearcote/Repel

Finecote Quick Render Texprime (Tinted) Finecote 1mm DFT** Clearcote/Repel

Quicksand Coarse Quick Render Texprime (Tinted) Quicksand Coarse Clearcote/Repel

Santa Fe Quick Render Texprime (Tinted) Santa Fe Clearcote/Repel

** Dry Film Thickness - ROCKCOTE Finecote and Acrylic Texture Fine will require two applications to achieve 1mm build


BRICK & BLOCK – CONTINUED _________________________________________________________________________________________________

High Performance Membranes (Standard) Up to 10 YEAR WARRANTY*


Armour Flex (Medium Profile)

Quick Render Armour Flex (stipple) Armour Flex

Armoured Sponge Finish Quick Render Armour Armour

Armoured Fast Float Finish Medium

Quick Render Fast Float Finish Medium Armour Armour

Armoured Fast Float Finish Classic 1, 1.5, 2, 3mm

Quick Render Fast Float Finish Classic 1, 1.5, 2, 3mm

Armour Armour

Polished Concrete Finish 7.5 YEAR WARRANTY*


Smooth Set White Quick Render Smooth Set White Smooth Set White Repel

Smooth Sanding Patch Quick Render Smooth Sanding Patch**

Smooth Sanding Patch**

Repel

** Requires the addition of General Purpose Portland Cement when used externally.

Matte Finishes 7.5 YEAR WARRANTY*


Render Paint Fine Quick Render Render Paint Fine Render Paint Fine

Render Paint Flat Quick Render Render Paint Flat Render Paint Flat

Toscani Quick Render Toscani Toscani

Santini Bagged Anti-Efflorescent Primer Santini

Santini Quick Render Texprime Tinted Santini Clearcote/Repel

Concote Bagged Anti-Efflorescent Primer Concote


OFF-FORM CONCRETE _________________________________________________________________________________________________ Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination. Surface

must be wet down prior to the application of ROCKCOTE Keycote and once shine has gone, apply Keycote leaving it rough to provide optimum adhesion for the Quick Render. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). For Paint Systems:

Grind form joints where required, apply two tight coats of ROCKCOTE Smooth Sanding Patch or ROCKCOTE Smooth Set to flush off and feather out joints. Any large imperfections in the joints should be patched with ROCKCOTE Patch & Prep then finished with ROCKCOTE Smooth Sanding Patch or ROCKCOTE Smooth Set White depending on level of finish required. Important: If total thickness of coating system is to exceed 10mm, and is to be less than 30mm, use Quick Render

PM100 High Build as a base coat prior to the application of Quick Render. For coating systems greater than 30mm, contact ROCKCOTE Technical Department. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

ROCKCOTE Premium High Performance Membrane RENDER Systems Up to 15 YEAR WARRANTY*

Finish required 1st Step 2nd Step*** (OPTIONAL)

3rd Step 4th Step 5th Step

Armoured Sponge Finish Keycote Quick Render Polymer Render Grey Armour Armour

Armoured Santa Fe Keycote Quick Render Santa Fe Armour Armour

Armoured Trowel-On Keycote Quick Render Trowel On Armour Armour

Armoured Acrylic Texture Fine Keycote Quick Render 1mm Acrylic Texture Fine DFT**

Armour Armour


Keycote Quick Render Acrylic Texture Medium or Coarse

Armour Armour

Armoured Flexi Tex Medium Keycote Quick Render Flexi Tex Medium Armour Armour

** Dry Film Thickness – ROCKCOTE Acrylic Texture Fine will require two applications to achieve 1mm build

*** The 2nd Step is optional, depending on the substrate, level of build and finish required

ROCKCOTE Coloured Render Systems Up to 15 YEAR WARRANTY*



Sandcote Keycote Quick Render*** Texprime (Tinted) Sandcote Clearcote/Repel

Sandcote HydroGuard

Keycote Quick Render*** Texprime (Tinted) Sandcote HydroGuard

Pearlcote Keycote Quick Render*** Texprime (Tinted) Pearlcote Clearcote/Repel

Quicksand Coarse Keycote Quick Render*** Texprime (Tinted) Quicksand Coarse

Clearcote/Repel

Sandcote Solprime + Grit Texprime Tinted Sandcote Clearcote/Repel


OFF-FORM CONCRETE – CONTINUED _________________________________________________________________________________________________

ROCKCOTE High Performance Membranes (Standard) RENDER Systems Up to 10 YEAR WARRANTY*



Armour Flex Stipple Keycote Quick Render Armour Flex (stipple) Armour Flex

Armoured Sponge Finish Keycote Quick Render Armour Armour

Fast Float Finish, Medium Keycote Quick Render Fast Float Finish, Medium Armour Armour

Fast Float Finish, Classic Keycote Quick Render Fast Float Finish, Classic Armour Armour

** The 2nd Step is optional, depending on the substrate, level of build and finish required.



Smooth Set White Quick Render Fibre Reinforced**

Smooth Set White

Smooth Set White

Repel

Smooth Sanding Patch

Keycote Quick Render** Smooth Sanding Patch***

Smooth Sanding Patch***

Repel

** The application of Quick Render is optional, depending on the substrate, level of build and finish required.

*** Requires the addition of General Purpose Portland Cement when used externally.



Render Paint Fine Keycote Quick Render Render Paint Fine Render Paint Fine

Render Paint Flat Keycote Quick Render Render Paint Flat Render Paint Flat

Toscani Keycote Quick Render Toscani Toscani

Concote Keycote Quick Render Texprime Tinted Concote

Painted Finishes Up to 10 YEAR WARRANTY*


Armour Solprime + Grit Armour Armour

Santini Bagged Solprime Texprime (Tinted) Santini

Render Paint Fine Solprime + Grit Render Paint Fine Render Paint Fine

Render Paint Flat Solprime + Grit Render Paint Flat Render Paint Flat

Toscani Solprime + Grit Toscani Toscani

Finecote Solprime Texprime (Tinted) Finecote 1mm DFT** Clearcote/Repel

Concote Solprime Texprime (Tinted) Concote

** Dry Film Thickness – ROCKCOTE Finecote will require two applications to achieve 1mm build


OFF-FORM CONCRETE CEILINGS & SOFFITS _________________________________________________________________________________________________

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.

Grind form joints where required, apply two tight coats of ROCKCOTE Smooth Sanding Patch or ROCKCOTE Smooth Set White to flush off and feather out joints. Any large imperfections in the joints should be patched with ROCKCOTE Patch & Prep then finished with ROCKCOTE Smooth Sanding Patch or ROCKCOTE Smooth Set depending on level of finish required. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior

to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

ROCKCOTE Paint Systems Up to 10 YEAR WARRANTY*


Armour Flex Stipple Masonry Primer Hi Op Armour Flex (stipple) Armour Flex

Claytex Masonry Primer Hi Op Claytex


TILT-UP PRE-CAST CONCRETE PANEL _________________________________________________________________________________________________

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, release agents or any other

contamination. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: Fill small holes with ROCKCOTE Smooth Sanding Patch or ROCKCOTE Smooth Set White. Larger

imperfections should be filled with ROCKCOTE Patch and Prep and finished with ROCKCOTE Smooth Sanding Patch or ROCKCOTE Smooth Set White depending on level of finish required. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

ROCKCOTE Premium High Performance Membrane Systems Up to 15 YEAR WARRANTY*


Armoured Sponge Finish Solprime + Grit Polymer Render Grey Armour Armour

Armoured Santa Fe Solprime + Grit Santa Fe Armour Armour

Armoured Trowel-On Solprime + Grit Trowel-On Armour Armour

Armoured Acrylic Texture Fine Solprime + Grit Acrylic Texture Fine 1mm DFT** Armour Armour


Solprime + Grit Acrylic Texture Medium or Coarse Armour Armour

Armoured Flexi Tex Medium Flexi Tex Medium Armour Armour

** Dry Film Thickness - ROCKCOTE Acrylic Texture Fine will require two applications to achieve 1mm build



Sandcote Solprime Texprime (Tinted) Sandcote Clearcote/ Repel

Sandcote HydroGuard Solprime Texprime (Tinted) Sandcote HydroGuard

Pearlcote Solprime Texprime (Tinted) Pearlcote Clearcote/ Repel

Quicksand Coarse Solprime Texprime (Tinted) Quicksand Coarse Clearcote/ Repel

Finecote Solprime Texprime (Tinted) Finecote 1mm DFT** Clearcote/ Repel


ROCKCOTE High Performance Membranes (Standard) Up to 10 YEAR WARRANTY*

Finish required 1st Step 2nd Step 3rd Step

Armour Flex Stipple Solprime Armour Flex Stipple Armour Flex

Armour Solprime Armour Armour


TILT-UP (CONCRETE PANEL) – CONTINUED _________________________________________________________________________________________________


Finish required 1st Step 2nd Step 3rd Step 4th Step 5th Step

Smooth Set White Smooth Set White

Smooth Set White

Repel


Keycote Quick Render** Smooth Sanding Patch***

Smooth Sanding Patch***

Repel

** The 2nd Step is optional, depending on the substrate, level of build and finish required.

*** Requires the addition of General Purpose Portland Cement when used externally.



Render Paint Flat Solprime + Grit Render Paint Flat Render Paint Flat

Render Paint Fine Solprime + Grit Render Paint Fine Render Paint Fine

Toscani Solprime + Grit Toscani Toscani

Santini Solprime Texprime (Tinted) Santini

Concote Solprime Texprime (Tinted) Concote


EXPANDED POLYSTYRENE (EPS) PANELS OR BLOCKS

ROCKCOTE REINFORCED RENDER SYSTEMS (RRR) _________________________________________________________________________________________________

Surface Preparation: Substrate must be dry, clean and free of dust, dirt, oil, salt, mould or any other contamination.

Ensure that the EPS Panels have been fixed as per manufacturer’s specifications. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: ROCKCOTE will not warrant the use of colours with a LRV [Light Reflectance Value] of less than 40% over

Polystyrene Cladding systems. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Note: Mesh is to be ROCKCOTE as per RRR System manual. Please refer to the RRR Dry Zone Walling System manual

for complete instruction of system installation. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey Armour Armour

Armoured Santa Fe 4-8mm Quick Render PM100 & Mesh

Santa Fe Armour Armour

Armoured Trowel-On 4-8mm Quick Render PM100 & Mesh

Trowel-On Armour Armour

Armoured Acrylic Texture Fine 4-8mm Quick Render PM100 & Mesh

1mm Acrylic Texture Fine DFT**

Armour Armour


4-8mm Quick Render PM100 & Mesh

Acrylic Texture Medium or Coarse

Armour Armour

Armoured Flexi Tex Medium 4-8mm Quick Render PM100 & Mesh

Flexi Tex Medium Armour Armour




Sandcote 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Sandcote Clearcote/ Repel

Sandcote HydroGuard


Texprime (Tinted) Sandcote HydroGuard

Pearlcote 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Pearlcote Clearcote/ Repel

Finecote 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Finecote 1mm DFT** Clearcote/ Repel

Quicksand Coarse 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Quicksand Coarse Clearcote/ Repel

** Dry Film Thickness - ROCKCOTE Finecote will require two applications to achieve 1mm build


EXPANDED POLYSTYRENE (EPS) PANELS OR BLOCKS – CONTINUED _________________________________________________________________________________________________



Render Paint Fine 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey

Render Paint Fine Render Paint Fine

Render Paint Flat 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey

Render Paint Flat Render Paint Flat

Toscani 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey

Toscani Toscani





Polymer Render Grey



Repel



AAC PANEL (75MM) _________________________________________________________________________________________________

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination.

Patch any deep holes or imperfections with ROCKCOTE Patch & Prep. If a greater working time is required the surface can be sealed with ROCKCOTE Rockbond 27 before commencing application of Step 1 in order to control absorption and improve adhesion and minimise joint grinning. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: These systems are dependant on correct and straight installation of the cladding and the level of finish

required. If walls require straightening apply ROCKCOTE Rockbond 27, then a base coat of ROCKCOTE Quick Render FR (Fibre Reinforced) to achieve desired level (this can replace the Polymer Render in Step 1). ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish Quick Render Fibre Reinforced (FR)

Quick Render Fibre Reinforced (FR)

Armour Armour

Armoured Santa Fe Quick Render Fibre Reinforced (FR)


Armoured Trowel On (1 & 1.5mm)


Trowel On Trowel On (1 & 1.5mm)

Armour Armour

Armoured Trowel-On (2mm & 3mm only)

Texprime Trowel-On (2mm & 3mm only)

Armour Armour

Armoured Acrylic Texture Fine



Armour Armour




Armour Armour





ROCKCOTE Coloured Render System Up to 15 YEAR WARRANTY*


Sandcote Polymer Render Grey (Tinted) Sandcote Clearcote/ Repel

Pearlcote Polymer Render Grey (Tinted) Pearlcote Clearcote/ Repel

Finecote Polymer Render Grey (Tinted) 1mm Finecote DFT** Clearcote/ Repel

Quicksand Coarse Polymer Render Grey (Tinted) Quicksand Coarse Clearcote/ Repel



AAC PANEL (75MM)– CONTINUED _________________________________________________________________________________________________



Render Paint Flat Polymer Render Grey or QRender FR

Polymer Render Grey or QRender FR

Render Paint Flat

Render Paint Flat

Render Paint Fine Polymer Render Grey or QRender FR


Render Paint Fine

Render Paint Fine

Toscani Polymer Render Grey or QRender FR


Toscani Toscani

Santini Bagged (Option 1)

Polymer Render Grey (Tinted)

Santini 1mm DFT**

Santini Bagged (Option 2)

1mm Santini DFT** Santini 1mm DFT**

Concote Bagged Polymer Render Grey (Tinted)

Concote 1mm DFT**

** Dry Film Thickness - ROCKCOTE Santini and Concote may require two applications to achieve 1mm build




Polymer Render Grey

Polymer Render Grey



Repel



AAC PANEL (50MM) _________________________________________________________________________________________________

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination.

Patch any deep holes or imperfections with ROCKCOTE Patch & Prep. If a greater working time is required the surface can be sealed with ROCKCOTE Rockbond 27 before commencing application of Step 1 in order to control absorption and improve adhesion and minimise joint grinning. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: These systems are dependant on correct and straight installation of the cladding and the level of finish

required. If walls require straightening apply ROCKCOTE Rockbond 27, then a base coat of ROCKCOTE Quick Render FR (Fibre Reinforced) to achieve desired level (this can replace the Polymer Render in Step 1). AAC panels must be installed strictly as per manufacturer’s specifications. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish

Quick Render PM100 & Mesh

Polymer Render Masonry Hi Op Primer

Armour Armour

Armoured Trowel On Quick Render PM100 & Mesh

Trowel On Trowel On Masonry Hi Op Primer

Armour Armour




Masonry Hi Op Primer

Armour Armour




Masonry Hi Op Primer Armour Armour



Flexi Tex Medium Masonry Hi Op Primer

Armour Armour


ROCKCOTE Coloured Render System Up to 15 YEAR WARRANTY*


Sandcote Quick Render PM100 & Mesh


Pearlcote Quick Render PM100 & Mesh


Finecote Quick Render PM100 & Mesh

Texprime (Tinted) 1mm Finecote DFT** Clearcote/ Repel

Quicksand Coarse Quick Render PM100 & Mesh




AAC PANEL(50MM) – CONTINUED _________________________________________________________________________________________________



Render Paint Flat Quick Render PM100 & Mesh

Polymer Render Grey Render Paint Flat

Render Paint Flat

Render Paint Fine Quick Render PM100 & Mesh

Polymer Render Grey Render Paint Fine

Render Paint Fine

Toscani Quick Render PM100 & Mesh

Polymer Render Grey Toscani Toscani

Santini Bagged Quick Render PM100 & Mesh


Santini 1mm DFT**

Concote Bagged Quick Render PM100 & Mesh


Concote 1mm DFT**

** Dry Film Thickness - ROCKCOTE Santini and Concote may require two applications to achieve 1mm build








Repel



BLUEBOARD FIBRE CEMENT SHEETING _________________________________________________________________________________________________

Surface Preparation: Sheets must be installed strictly in accordance with manufacturer’s specifications.

Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch, tape and set all recessed joints with ROCKCOTE Patch & Prep and 150gsm Non Adhesive Alkali Resistant Mesh Tape. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: Blueboard Fibre Cement sheeting requires a minimum 2mm DFT [Dry Film Thickness] acrylic render or texture

over the entire surface. ROCKCOTE does not recommend the use of colours with a LRV [Light Reflectance Value] of less than 40% over Blueboard Fibre Cement sheeting. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Finish required 1st Step (set joints) 2nd Step 3rd Step 4th Step 5th Step

Armoured Sponge Finish

Patch & Prep & Mesh Tape

Polymer Render Grey

Polymer Render Grey

Armour Armour

Armoured Santa Fe Patch & Prep & Mesh Tape

Polymer Render Grey


Armoured Trowel-On Patch & Prep & Mesh Tape

Polymer Render Grey




Polymer Render Grey


Armour Armour



Polymer Render Grey


Armour Armour



Flexi Tex Medium




BLUEBOARD FIBRE CEMENT SHEETING – CONTINUED _________________________________________________________________________________________________



Sandcote (Option 1)


Texprime (Tinted)

Sandcote Sandcote Repel/ Clearcote

Sandcote (Option 2)



Sandcote Repel/ Clearcote

Sandcote HydroGuard



Sandcote HydroGuard

Pearlcote Patch & Prep & Mesh Tape


Pearlcote Repel/ Clearcote

Finecote Patch & Prep & Mesh Tape


Finecote 1mm DFT**

Repel/ Clearcote

Quicksand Coarse (Option 1)


Texprime (Tinted)

Quicksand Coarse

Quicksand Coarse

Repel/ Clearcote

Quicksand Coarse (Option 2)



Quicksand Coarse

Repel/ Clearcote

**Dry Film Thickness - ROCKCOTE Finecote will require two applications to achieve 1mm build

**Dry Film Thickness - ROCKCOTE Santini will require two applications to achieve 1mm build


Finish required 1st Step 2nd Step 3rd Step 4th Step 5th Step 6th Step


Patch & Prep and mesh tape

Polymer Render Grey

Polymer Render Grey



Repel


ROCKCOTE Matte Finishes 7.5 YEAR WARRANTY*


Render Paint Fine Patch & Prep & Mesh Tape

Polymer Render Grey

Polymer Render Grey

Render Paint Fine

Render Paint Fine

Render Paint Flat Patch & Prep & Mesh Tape

Polymer Render Grey

Polymer Render Grey

Render Paint Flat

Render Paint Flat

Toscani Patch & Prep & Mesh Tape

Polymer Render Grey


Toscani Toscani

Santini Patch & Prep & Mesh Tape


Santini 1mm DFT**

N/A N/A

Concote Patch & Prep & Mesh Tape

Polymer Render Grey

Polymer Render Grey

Texprime (Tinted)

Concote


CORE FILLED FIBRE CEMENT

AFS LOGIC WALL _________________________________________________________________________________________________

Adhesion Requirements: Before applying any coatings, please ensure the surface contains no more than 15% moisture

(WME). Surface Preparation: Sheets should be installed strictly in accordance with manufacturer’s specifications.

Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch, tape and set all recessed joints with ROCKCOTE Patch & Prep and 150gsm Non Adhesive Alkali Resistant Mesh Tape. Important: Sheeting requires a minimum 2mm DFT [Dry Film Thickness] acrylic render or texture over the entire surface.

ROCKCOTE does not recommend the use of colours with a LRV [Light Reflectance Value] of less than 25% over core filled fibre cement sheeting. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. If a screedable basecoat render is required apply ROCKCOTE Quick Render FR (Fibre Reinforced) in lieu of Polymer Render Grey in Step 2. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish Patch & Prep & Mesh Tape

Polymer Render Grey

Polymer Render Grey

Armour Armour


Polymer Render Grey



Polymer Render Grey




Polymer Render Grey

Acrylic Texture Fine 1mm DFT**

Armour Armour



Polymer Render Grey


Armour Armour



AFS LOGIC WALL CORE FILLED FIBRE CEMENT – CONTINUED _________________________________________________________________________________________________



Sandcote Patch & Prep & Mesh Tape

Polymer Render Grey

Texprime (Tinted)


Sandcote HydroGuard


Polymer Render Grey

Texprime (Tinted)

Sandcote HydroGuard

Quicksand Coarse Patch & Prep & Mesh Tape

Polymer Render Grey

Texprime (Tinted)

Quicksand Coarse Repel/ Clearcote


Polymer Render Grey

Texprime (Tinted)

Finecote 1mm DFT**

Repel/ Clearcote


Polymer Render Grey

Texprime (Tinted)


*Polymer Render Grey in Step 2 can be substituted with Quick Render FR, up to 8mm



CORE FILLED FIBRE CEMENT

RITEK XL _________________________________________________________________________________________________ Adhesion Requirements: Before applying any coatings, please ensure the surface contains no more than 15% moisture

(WME). Surface Preparation: Sheets should be installed strictly in accordance with manufacturer’s specifications.

Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch, tape and set all recessed joints with ROCKCOTE Patch & Prep and 150gsm Non Adhesive Alkali Resistant Mesh Tape. All aluminium joiners must have 150gsm Non Adhesive Alkali Resistant Mesh Tape embedded into the Keycote to at least 100mm either side of the aluminium edge. Where aluminium joiners, recessed joints or internal or external corners are within 200mm of each other the entire section should be meshed. Important: Sheeting requires a minimum 2mm DFT [Dry Film Thickness] acrylic render or texture over the entire surface.

ROCKCOTE does not recommend the use of colours with a LRV [Light Reflectance Value] of less than 25% over core filled fibre-cement sheeting. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. If a screedable basecoat render is required apply ROCKCOTE Quick Render FR (Fibre Reinforced) in lieu of Polymer Render Grey in Step 2, where applicable. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

ROCKCOTE Premium High Performance Membrane System Up to 15 YEAR WARRANTY*



Patch & Prep + Mesh Tape

Keycote Acrylic Texture Fine 1mm DFT**

Armour Armour


Patch & Prep + Mesh Tape

Keycote Acrylic Texture Medium or Coarse

Armour Armour

Armoured Flexi Tex Medium Patch & Prep + Mesh Tape

Keycote Flexi Tex Medium Armour Armour

Armoured Sponge Finish Patch & Prep + Mesh Tape

Keycote Polymer Render Grey

Armour Armour

Armoured Trowel On Patch & Prep + Mesh Tape

Keycote Trowel On Armour Armour

Armoured Santa Fe Keycote & Mesh Tape

Keycote Santa Fe Armour Armour

**Dry Film Thickness - ROCKCOTE Acrylic Texture Fine will require two applications to achieve 1mm build


RITEK XL CORE FIBRE CEMENT – CONTINUED _________________________________________________________________________________________________




Polymer Render Grey

Texprime (Tinted)


Sandcote HydroGuard


Polymer Render Grey

Texprime (Tinted)

Sandcote HydroGuard


Polymer Render Grey

Texprime (Tinted)

Quicksand Coarse

Repel/ Clearcote


Polymer Render Grey

Texprime (Tinted)

Finecote 1mm DFT**

Repel/ Clearcote


Polymer Render Grey

Texprime (Tinted)


* Polymer Render Grey in Step 2 can be substituted with Quick Render FR, up to 8mm



EXTRUDED POLYSTYRENE (XPS)

INCLUDING FOAMULAR METRIC & ISOBOARD _________________________________________________________________________________________________

Adhesion Requirements: All XPS Polystyrene cladding must have ROCKCOTE Keycote applied to the entire substrate

leaving surface rough to provide optimum adhesion for ROCKCOTE PM100 application. Surface Preparation: Substrate must be dry, clean and free of dust, dirt, oil, salt, mould or any other contamination.

Ensure that the XPS Panels have been fixed as per manufacturer’s specifications. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: ROCKCOTE does not recommend the use of colours with a LRV [Light Reflectance Value] of less than 40%

over Polystyrene Cladding systems. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Note: Mesh is to be ROCKCOTE as per RRR System manual. Please refer to the RRR Dry Zone Walling System manual

for complete instruction of system installation. If additional warranty periods are required, please contact ROCKCOTE Technical Department for advice. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

ROCKCOTE Premium High Performance Membrane Systems 7.5 YEAR WARRANTY*


Armoured Sponge Finish Keycote 4-8 mm Quick Render PM100 & Mesh

Polymer Render Grey

Armour Armour

Armoured Santa Fe Keycote 4-8 mm Quick Render PM100 & Mesh


Armoured Trowel-On Keycote 4-8 mm Quick Render PM100 & Mesh



Keycote 4-8 mm Quick Render PM100 & Mesh


Armour Armour




Armour Armour






EXTRUDED POLYSTYRENE (XPS) – CONTINUED _________________________________________________________________________________________________

ROCKCOTE Coloured Render Systems 7.5 YEAR WARRANTY*


Sandcote Keycote 4-8mm Quick Render PM100 & Mesh


Sandcote HydroGuard Keycote 4-8mm Quick Render PM100 & Mesh


Pearlcote Keycote 4-8mm Quick Render PM100 & Mesh


Finecote Keycote 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Finecote 1mm DFT**

Clearcote/ Repel

Quicksand Coarse Keycote 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Quicksand Coarse

Clearcote/ Repel

** Dry Film Thickness - ROCKCOTE Finecote may require two applications to achieve 1mm build



Render Paint Fine Keycote 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey


Render Paint Flat Keycote 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey


Toscani Keycote 4-8mm Quick Render PM100 & Mesh


Toscani Toscani

Santini Keycote 4-8mm Quick Render PM100 & Mesh


Santini 1mm


PRE-MESHED EPS _________________________________________________________________________________________________

Adhesion Requirements: All Pre-Meshed Polystyrene cladding must have ROCKCOTE Keycote applied to the entire

substrate leaving surface rough to provide optimum adhesion for ROCKCOTE Quick Render PM100 application. Surface Preparation: Substrate must be dry, clean and free of dust, dirt, oil, salt, mould or any other contamination.

Ensure that the EPS Panels have been fixed as per manufacturer’s specifications. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: ROCKCOTE does not recommend the use of colours with a LRV [Light Reflectance Value] of less than 40%

over Polystyrene Cladding systems. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Note: Mesh is to be ROCKCOTE as per RRR System. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish Keycote 4-8 mm Quick Render PM100 & Mesh

Polymer Render Grey

Armour Armour

Armoured Santa Fe Keycote 4-8 mm Quick Render PM100 & Mesh


Armoured Trowel-On Keycote 4-8 mm Quick Render PM100 & Mesh





Armour Armour




Armour Armour




** Dry Film Thickness – ROCKCOTE Acrylic Texture Fine will require two coats to achieve 1mm build



Sandcote Keycote 4-8mm Quick Render PM100 & Mesh


Sandcote HydroGuard

Keycote 4-8mm Quick Render PM100 & Mesh


Pearlcote Keycote 4-8mm Quick Render PM100 & Mesh


Finecote Keycote 4-8mm Quick Render PM100 & Mesh

Texprime (Tinted) Finecote 1mm DFT**

Clearcote/ Repel

Quicksand Coarse Keycote 4-8mm Quick Render PM100 & Mesh




PRE-MESHED EPS – CONTINUED _________________________________________________________________________________________________

** Dry Film Thickness - ROCKCOTE Santini may require two applications to achieve 1mm build



Render Paint Fine Keycote 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey

Render Paint Fine

Render Paint Fine

Render Paint Flat Keycote 4-8mm Quick Render PM100 & Mesh

Polymer Render Grey

Render Paint Flat

Render Paint Flat

Toscani Keycote 4-8mm Quick Render PM100 & Mesh


Toscani Toscani

Santini Keycote 4-8mm Quick Render PM100 & Mesh


Santini 1mm DFT**


SITE MIX (SAND & CEMENT) RENDER _________________________________________________________________________________________________ Adhesion Requirements: Surface must not be powdery. Surface Preparation: Substrate must be clean and free of dust, oil, dirt, mould or any other contamination. Repair any

cracks, holes and other patches with ROCKCOTE Quick Render. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Prime with ROCKCOTE Anti Efflorescence Primer [AE Primer]. Important: New Site Mix Cement render should be fully cured for 28 days.

ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish AE Primer Polymer Render Grey Armour Armour

Armoured Santa Fe AE Primer Santa Fe Armour Armour

Armoured Trowel-On AE Primer Trowel-On Armour Armour

Armoured Acrylic Texture Fine AE Primer Acrylic Texture Fine 1mm DFT** Armour Armour


AE Primer Acrylic Texture Medium or Coarse Armour Armour

Armoured Flexi Tex Medium AE Primer Flexi Tex Medium Armour Armour

**Dry Film Thickness – ROCKCOTE Acrylic Texture Fine will require two coats to achieve 1mm build



Sandcote AE Primer Sandcote Clearcote/ Repel

Sandcote HydroGuard AE Primer Sandcote HydroGuard

Pearlcote AE Primer Pearlcote Clearcote/ Repel

Finecote AE Primer Finecote 1mm DFT** Clearcote/ Repel

Quicksand Coarse AE Primer Quicksand Coarse Clearcote/ Repel

** Dry Film Thickness -ROCKCOTE Finecote will require two applications to achieve 1mm dry film build


SITE MIX RENDER – CONTINUED _________________________________________________________________________________________________



Smooth Set White Smooth Set White Smooth Set White Repel



Render Paint Fine AE Primer Render Paint Fine Render Paint Fine

Render Paint Flat AE Primer Render Paint Flat Render Paint Flat

Toscani AE Primer Toscani Toscani

Concote AE Primer Concote 1mm DFT**

Santini AE Primer Santini 1mm DFT**

** Dry Film Thickness -ROCKCOTE Santini and Concote may require two applications to achieve 1mm dry film build



Armour Flex (Stipple) AE Primer Armour Flex (stipple) Armour Flex

Armour AE Primer Armour Armour


PREVIOUSLY PAINTED/COATED MASONRY _________________________________________________________________________________________________

Adhesion Requirements: Check the adhesion of the existing coating on every wall and at least every 3 metres over the

proposed application areas. Glossy and smooth surfaces should be sanded with a coarse grit sanding paper to ensure a key for satisfactory adhesion. If the old paint is oxidized or chalky apply an alkali-resistant, penetrating primer /sealer. Surface Preparation: Remove all loose materials. Any loose or peeling paint should be scraped back to a firm and sound

substrate to leave surfaces clean and free of dust, oil, dirt, mould or any other contamination. Apply ROCKCOTE Keycote to entire surface to a thickness of 1-2mm leaving surface rough to provide suitable key for render application and to provide optimum adhesion for ROCKCOTE Quick Render. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Important: If total thickness of coating system is to exceed 10mm, and is to be less than 30mm, use Quick Render PM100

High Build as a base coat prior to the application of Quick Render. For coating systems greater than 30mm, contact ROCKCOTE Technical Department. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish Keycote Quick Render Polymer Render Grey Armour Armour

Armoured Santa Fe Keycote Quick Render Santa Fe Armour Armour

Armoured Trowel-On Keycote Quick Render Trowel-On Armour Armour


Keycote Quick Render Acrylic Texture Fine 1mm DFT**

Armour Armour


Keycote Quick Render Acrylic Texture Medium or Coarse

Armour Armour


Keycote Quick Render Flexi Tex Medium Armour Armour




Sandcote Keycote Quick Render Texprime (Tinted) Sandcote Clearcote/ Repel

Sandcote HydroGuard Keycote Quick Render Texprime (Tinted) Sandcote HydroGuard

Pearlcote Keycote Quick Render Texprime (Tinted) Pearlcote Clearcote/ Repel

Finecote Keycote Quick Render Texprime (Tinted) Finecote 1mm DFT**

Clearcote/ Repel

Quicksand Coarse Keycote Quick Render Texprime (Tinted) Quicksand Coarse

Clearcote/ Repel



PAINT & TEXTURE SYSTEMS OVER FLAT PREVIOUSLY

PAINTED/COATED MASONRY _________________________________________________________________________________________________ Adhesion Requirements: Check the adhesion of the existing coating on every wall and at least every 3 metres over the

proposed application areas. Glossy and smooth surfaces should be sanded with a coarse grit sanding paper to ensure a key for satisfactory adhesion. If the old paint is oxidized or chalky apply an alkali-resistant, penetrating primer /sealer. Before applying any coatings, please ensure the surface contains no more than 15% moisture (WME). Surface Preparation: Remove all loose materials. Any loose or peeling paint should be scraped back to a firm and sound

substrate to leave surfaces clean and free of dust, oil, dirt, mould or any other contamination. Important: ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op be applied prior

to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Armoured Sponge Finish Polymer Render Grey Polymer Render Grey Armour Armour

Armoured Santa Fe Texprime Santa Fe Armour Armour

Armoured Trowel-On Texprime Trowel-On Armour Armour


Texprime Acrylic Texture Fine 1mm DFT** Armour Armour


Texprime Acrylic Texture Medium or Coarse Armour Armour


Texprime Flexi Tex Medium Armour Armour

** Dry Film Thickness - ROCKCOTE Acrylic Texture Fine will require two applications to achieve 1mm build.



Armour Flex Stipple

Level Surface

Armour Flex Stipple Armour Flex

Armoured Sponge Finish Armour Armour



Render Paint Fine

Level Surface


Render Paint Flat Render Paint Flat Render Paint Flat

Santini Texprime (Tinted) Santini 1mm DFT**

Concote Texprime (Tinted) Concote 1mm DFT**

** Dry Film Thickness - ROCKCOTE Concote will require two applications to achieve 1mm build


MAGNESIUM BOARD (MGO)

MODAK, INX _________________________________________________________________________________________________

Surface Preparation: Before applying any coatings, please ensure the surface contains no more than 15% moisture

(WME). Certain types of air-dried MGO board can retain large quantities of water when wet.

Sheets should be installed strictly in accordance with manufacturer’s specifications. ROCKCOTE recommends the installation of control/ relief joints at no more than 6m for vertical relief joints and 3m for horizontal relief joints. Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch, tape and set all recessed joints with ROCKCOTE Patch & Prep and 155gsm Non Adhesive Alkali Resistant Mesh Tape. Important: MGO Board sheeting requires a minimum 1mm DFT [Dry Film Thickness] acrylic render over the Keycote

surface. ROCKCOTE does not recommend the use of dark colours with a LRV [Light Reflectance Value] of less than 40% over Magnesium Board sheeting. ROCKCOTE recommends that on large broad wall areas, ROCKCOTE Masonry Primer Hi Op to be applied prior to the application of Armour to ensure uniform coverage and colour consistency. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Finish 1st Step 2nd Step 3rd Step 4th Step 5th Step

Armoured Sponge Finish Patch & Prep & Mesh Tape

Keycote Polymer Render Grey Armour Armour

Armoured Santini Patch & Prep & Mesh Tape

Keycote 1mm Santini Armour Armour


Keycote Santa Fe Armour Armour


Keycote Trowel-On Armour Armour



Keycote Acrylic Texture Fine 1mm DFT**

Armour Armour



Keycote Acrylic Texture Medium or Coarse

Armour Armour

Armoured FlexiTex Patch & Prep & Mesh Tape

Keycote FlexiTex Armour Armour



MAGNESIUM BOARD (MGO) – CONTINUED _________________________________________________________________________________________________


Finish 1st Step 2nd Step 3rd Step 4th Step 5th Step***


Keycote Texprime (Tinted) Sandcote Clearcote/ Repel

Sandcote HydroGuard


Keycote Texprime (Tinted) Sandcote HydroGuard


Keycote Texprime (Tinted) Pearlcote Clearcote/ Repel


Keycote Texprime (Tinted) Finecote 1mm DFT** Clearcote/ Repel


Keycote Texprime (Tinted) Quicksand Coarse Clearcote/ Repel


Keycote Texprime (Tinted) 1mm Santini Clearcote/ Repel

** Dry Film Build - ROCKCOTE Finecote will require two applications to achieve 1mm build


Finish 1st Step 2nd Step 3rd Step 4th Step 5th Step

Render Paint Fine (Option 1)



Render Paint Fine

Render Paint Fine

Render Paint Fine (Option 2 – Smooth Side of Board)

MgO Board Primer


Render Paint Flat (Option 1)



Render Paint Flat

Render Paint Flat

Render Paint Flat (Option 2 – Smooth Side of Board)

MgO Board Primer


Toscani Patch & Prep & Mesh Tape


Toscani Toscani


Keycote Polymer Render Grey (Tinted)

Santini Santini

Concote Patch & Prep & Mesh Tape

Keycote Polymer Render Grey (Tinted)

Concote Concote

Armour (Smooth Side of Board)

MgO Board Primer

Armour Armour


ROCKCOTE Paint Systems Guide

WARRANTY SUGGESTED USES KEY FEATURES

15 Year Warranty *

ROCKCOTE EcoStyle

Interior and Exterior Paint Zero VOCs

Low odour

100% acrylic

GECA certified

www.geca.org.au

Scrubbable & washable

Easy application

Unlimited colour range

15 Year Warranty *

ROCKCOTE Solar Protect

Roof Paint Protective membrane coating

Resilient protection against the harsh Australian climate

UV resistant

Safe for capturing potable water

Resists pollution & minimises dirt retention

Crack bridging

Water repellent

Choose from soft, natural tones to vibrant colours

Available in Satin and Gloss finishes

Applied with airless spray gun, roller or brush

Manufacturers warranty

*15 Year Warranty

ROCKCOTE Warrants that if applied correctly on properly prepared substrates, as per both our specifications AND Maintenance Guide, it will not flake, peel or blister for 15 years. Paint failure caused by any breakdown of a previous coating is not covered by this warranty. ROCKCOTE recommends that you always contact us to confirm the best ROCKCOTE system for your needs 1300 736 668. ROCKCOTE reserves the right to change any of the above at any time without notice.

http://www.geca.org.au/


ROCKCOTE EcoStyle

ECOSTYLE OVER PLASTERBOARD WALLS _________________________________________________________________________________________________

Surface Preparation: Ensure the surface is free from loose material. Wipe down to ensure the surface is clean, dry and

dust free. Patch and fill holes and cracks with ROCKCOTE Smooth Sanding Patch. Do not sand the paper face of plasterboard. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

EcoStyle Low Sheen or Satin

Steps Product Used Method of Application Spreading Rate Dry Coating Thickness (mm)

Dry Time

1 EcoStyle Sealer Undercoat

Brush, Roller or Spray 16m2/ltr

27 microns

2hrs

2 EcoStyle (Low Sheen or Satin)

Roller or Spray

14-16m2/ltr 25-29 microns 2hrs


Roller or Spray

14-16m2/ltr

25-29 microns 2hrs

ECOSTYLE OVER FIBRO WALLS _________________________________________________________________________________________________


dust free. Patch and fill holes and cracks with ROCKCOTE Smooth Sanding Patch. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Dry Time



27 microns 2hrs


Roller or Spray



Roller or Spray

14-16m2/ltr

25-29 microns 2hrs


ECOSTYLE OVER MAGNESIUM BOARD (MGO) – SMOOTH SIDE _________________________________________________________________________________________________

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch,

tape and set all recessed joints with ROCKCOTE Patch & Prep and 155gsm Non Adhesive Alkali Resistant Mesh Tape. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Dry Time



27 microns 2hrs


Roller or Spray



Roller or Spray

14-16m2/ltr

25-29 microns 2hrs

ECOSTYLE CEILING WHITE OVER PLASTERBOARD CEILINGS _________________________________________________________________________________________________


dust free. Patch and fill holes and cracks with ROCKCOTE Smooth Sanding Patch. Do not sand the paper face of plasterboard. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

Premium Ceiling White

Steps Product Used Method of Application

Spreading Rate Dry Coating Thickness (mm)

Dry Time

1 EcoStyle Ceiling White Brush, Roller or Spray 14m2/ltr 30 microns 2hrs


ECOSTYLE CEILING WHITE OVER FIBRO CEILINGS _________________________________________________________________________________________________


dust free. Patch and fill holes and cracks with ROCKCOTE Smooth Sanding Patch. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

Premium Ceiling White


Dry Time

1 EcoStyle Sealer Undercoat Brush, Roller or Spray 16m2/ltr 27 microns 2hrs




ECOSTYLE OVER TIMBER _________________________________________________________________________________________________

Surface Preparation: Ensure the surface is free from loose material. Sand the surface to provide a smooth surface for

painting. Ensure the surface is clean, contains less than 15% WME [moisture] and is free from dirt oil and grease. Use a mixture of liquid detergent and warm water to lightly clean but do not allow timber to become saturated or heavily wet. Sand any non-porous surfaces such as glossy or sealed timber. Patch and fill holes and cracks with ROCKCOTE Smooth Sanding Patch. Hardwood timber or any timber prone to tannin or stain bleeding should be coated with suitable tannin blocker prior to application of Sealer Undercoat. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

EcoStyle Low Sheen, Satin, or Gloss


Dry Time


Roller or Spray

16m2/ltr

27 microns 2hrs

2 EcoStyle (Low Sheen, Satin or Gloss)

Roller or Spray



Roller or Spray

14-16m2/ltr

25-29 microns 2hrs

ECOSTYLE OVER PREVIOUSLY PAINTED SURFACES _________________________________________________________________________________________________

Surface Preparation: Ensure the surface is free from loose material. Remove all mould, mildew or fungi and treat these

areas with Fungicidal Wash. Ensure the surface is clean, contains less than 15% WME [moisture] and is free from release agents, oil and grease. Use a mixture of liquid detergent and warm water to clean. Flush all cleaned surfaces with clean water where there is no risk of water damage. Allow to fully dry before painting. Sand any non-porous surfaces such as glossy painted areas. Patch and fill holes and cracks with ROCKCOTE Smooth Sanding Patch. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

EcoStyle Low Sheen, Satin, or Gloss


Dry Time


Roller or Spray

16m2/ltr

27 microns 2hrs


Roller or Spray



Roller or Spray

14-16m2/ltr

25-29 microns 2hrs


SOLAR PROTECT _________________________________________________________________________________________________

Surface Preparation

For rainwater collection disconnect downpipes and only reconnect after 2 rain events of greater than 15mm has occurred.

Glossy surfaces should be lightly abraded.

High pressure clean with detergent & flush with clean water. Treat mould with ROCKCOTE Fungicidal Wash.

For tiled roofs, replace damaged tiles and repair pointing. ROCKCOTE Finecote can be used as a roof pointing.

For fibrous cement roofs, repair or replace cracked sheets.

If changing the roof colour to a bright or dark colour, tint Tile Roof Primer as close as possible to the final new colour of your roof. Seek advice from ROCKCOTE on tinting.

Please refer to the relevant Technical Specification & Safety Data Sheet before application.

ROCKCOTE Roof Coating System Up to 12 YEAR WARRANTY*

Roof type 1st Step 3rd Step 4th Step

Concrete Tiles (highly porous) Tile Roof Primer Solar Protect Solar Protect

Concrete Tiles (mildly porous or non-porous)

Tile Roof Primer Solar Protect Solar Protect

NOTE:

EXTERNAL ASBESTOS CEMENT PRODUCTS: Coating weathered asbestos cement products is not recommended.

The product should be removed and replaced using a licensed asbestos removal contractor if it is in poor condition.

Information provided in this booklet was correct at time of printing (13th March 2017).

For the latest ROCKCOTE Systems Guide and product information, visit the ROCKCOTE website:






2 ROCKCOTE Natural Materials Systems Guide | www.rockcote.com.au

ROCKCOTE Natural Materials Systems Guide | www.rockcote.com.au 3

Contents

ROCKCOTE Natural Materials Systems Guide .................................................................................................................. 4

External Substrates .............................................................................................................................................................. 5

Important Information ........................................................................................................................................................ 5

Brick & Block ..................................................................................................................................................................... 6

Brick & Block Painted ........................................................................................................................................................ 7

Off-Form Concrete ............................................................................................................................................................ 8

Hempcrete ........................................................................................................................................................................ 9

ROCKCOTE Render……………………………………………………………………………………………………………….10

Sand & Cement Render……………………………………………………………………………………………………………11

Painted Render……………………………………………………………………………………………………………………..12

Internal Substrates ............................................................................................................................................................. 13

Important Information ...................................................................................................................................................... 13

Plasterboard New & Painted ........................................................................................................................................... 14

Brick & Block ................................................................................................................................................................... 15

Brick & Block Painted ...................................................................................................................................................... 16

Off Form Concrete .......................................................................................................................................................... 17

Blueboard / Fibre Cement Sheeting ................................................................................................................................ 18

INEX Magnesium Board ................................................................................................................................................. 19

Hempcrete………………………………………………………………………….. ................................................................ 20

Wet Areas ............................................................................................................................................................................ 21

Important Information ...................................................................................................................................................... 21

Fibre Cement Cladding Designed Specifically For Wet Areas ........................................................................................ 22

Brick & Block ................................................................................................................................................................... 23

Off Form Concrete .......................................................................................................................................................... 24


ROCKCOTE Natural Materials Systems Guide

ROCKCOTE understands that everyone wants and expects different things from their architectural coatings. This systems guide helps assist property owners, applicators, builders and architects choose a traditional ROCKCOTE Natural Materials product to use on their project with consideration given to substrate, situation and finish. This document is designed to be used as a guide. If you need any further help, contact ROCKCOTE on 1300 736 668 or email at [email protected].

The question of “which system best suits the purpose” is dependent upon a number of factors:

1. Location 2. Environment 3. Substrate 4. Construction Type (Residential, Commercial or High Rise) 5. Green Rating (i.e. use of environmentally friendly materials) 6. Skills and experience of the applicator 7. Expectations of the client

ROCKCOTE is recognised for manufacturing high quality, consistent and reliable products. Our products meet all government statutory warranty responsibilities. The application of ROCKCOTE Natural Materials is a highly skilled process that requires experience working with natural building products and systems. It is the responsibility of the applicator to select the right product and system for the job and ensure correct installation and application according to the above and other relevant criteria. We recommend that project managers and clients appoint only applicators experienced in the relevant ROCKCOTE Natural Material in situations and with desired aesthetics similar to the project at hand. Colour Disclaimer

Being traditional natural products, ROCKCOTE Natural Materials will display their natural patina over time in different ways. If colour consistency and accuracy is required, customers should select a painted finish or one from ROCKCOTE’s extensive Coloured Render range instead. Many of the ROCKCOTE Natural Materials can be tinted with oxides, however colour consistency and accuracy will depend on a large variety of factors such as dispersing time, oxide type and drying times and polishing and burnishing techniques. ROCKCOTE strongly recommends a colour and finish sample be provided for sign off by the selected applicator or artisan prior to the start of each project. Always speak to ROCKCOTE first before deviating from this guide.

INDEMNITY ROCKCOTE Enterprises Pty Ltd will not accept responsibility for any misuse of this product or if not applied by a skilled and experienced applicator and in accordance with our technical specifications. Due to our policy of continuing product improvement ROCKCOTE Enterprises Pty Ltd reserves the right to change these specifications without further notice.

mailto:[email protected]


External Substrates

IMPORTANT INFORMATION _________________________________________________________________________________________________

Suitable Substrates:

For exterior purposes, certain ROCKCOTE Natural Materials are suitable for use over masonry and some traditional natural substrates including:

Brick and Block

Brick and Block Painted

Off Form Concrete

Hempcrete

ROCKCOTE Render

Sand & Cement Render

Painted Render

For a system specification for the following substrates, please contact ROCKCOTE Technical Department on 1300 736 668

Straw Bale

Magnesium Board

Blueboard

Fibre Cement Sheet

EPS Foam

AAC

Rammed Earth

Any unlisted substrate

Natural Materials Suitable for Exterior Use:

Natural Materials that are suitable for exterior use are limited to:

Lime Wash

Lime Plaster Basecote

Venetian Plaster

Marrakesh


External Substrates

BRICK & BLOCK _________________________________________________________________________________________________

Adhesion requirements: If bricks/blocks are smooth faced and have very little or excessive absorption rates, apply a

scratch coat made from Lime Plaster Basecote mixed with Gauging Water Mix (25% ROCKCOTE Fast Bond to 75% water). Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.

Substrate must be wet down to assist with correct hydration and bonding. Application of ROCKCOTE Lime Plaster Basecote may proceed once the “shine” has gone off the wall. Step 1 is required as a scratch coat (optional for Lime Wash). Limitations: Only for use over cavity brick/block systems. Single skin blockwork must be suitably waterproofed.

Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

FINISH 1st Step 2nd Step 3rd Step 4th Step 5th Step

Lime Wash - visible mortar joints

Lime Wash Lime Wash

Lime Wash - no visible mortar joints



Lime Wash Lime Wash

Lime Plaster Basecote Lime Plaster Basecote


Venetian Plaster Lime Plaster Basecote

Velvetina (1mm) Venetian Plaster Venetian Plaster

Repel

Marrakesh (Smooth, Trowel or Sponge Finish not polished)


Marrakesh (2-3mm coat)

Black Soap (optional)

Marrakesh (Lustre polished finish)


Marrakesh (2mm coat)


Black Soap


External Substrates

BRICK & BLOCK PAINTED _________________________________________________________________________________________________

Adhesion requirements: Check the adhesion of the existing coating on every wall and at least three metres over the

proposed application areas. Glossy and smooth surfaces should be sanded with a coarse grit sand paper to ensure a key for satisfactory adhesion. If the old paint is oxidised or chalky, apply an alkali-resistant, penetrating primer/sealer. Surface Preparation: Remove all loose materials. Any loose or peeling paint should be scraped back to a firm and sound

substrate to leave surfaces clean and free of dust, oil, dirt, salt, mould, or any other contamination. Apply the first step to entire surface to a thickness of 2mm leaving surface rough to provide a suitable key for application of the 2nd step. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Lime Wash – visible mortar joints

Lime Wash Lime Wash

Lime Wash – no visible mortar joints

Lime Plaster Basecote mixed with Gauging Water Mix*


Lime Wash Lime Wash

Lime Plaster Basecote Lime Plaster Basecote mixed with Gauging Water Mix*


Venetian Plaster Lime Plaster Basecote mixed with Gauging Water Mix*

Velvetina (1mm)

Venetian Plaster

Venetian Plaster

Repel











Black Soap

*Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your gauging water mix for the first coat of Lime

Plaster Basecote.


External Substrates

OFF-FORM CONCRETE _________________________________________________________________________________________________ Additional requirements: If total thickness of coating system is to exceed 8mm, contact the ROCKCOTE Technical

Department. Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination. Surface

must be wet down prior to the application of ROCKCOTE Lime Plaster Basecote and once shine has gone, apply Lime Plaster Basecote as per 1st step. Step 1 is required as a scratch coat. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Lime Wash Lime Plaster Basecote mixed with Gauging Water Mix*


Lime Wash Lime Wash





Velvetina (1mm)

Venetian Plaster

Venetian Plaster

Repel











Black Soap

*Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your gauging water mix for the first coat of Lime

Plaster Basecote.


External Substrates

HEMPCRETE _________________________________________________________________________________________________

Adhesion requirements: Substrate must not contain more than 15% moisture (WME) prior to the application of the

ROCKCOTE system. Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.



Lime Wash Lime Plaster Basecote (fully meshed)

Lime Wash Lime Wash

Lime Plaster Basecote Lime Plaster Basecote (fully meshed)


Venetian Plaster Lime Plaster Basecote (fully meshed)

Velvetina (1mm) Venetian Plaster

Venetian Plaster

Repel


External Substrates

ROCKCOTE RENDER ______________________________________________________________________________________

Adhesion Requirements: Surface must not be powdery and must be clean and free of dust, dirt, oil, salt,

mould, or any other contamination. Surface Preparation: Substrate must be clean and free of dust, oil, dirt, mould or any other contamination.

Repair any cracks, holes and other patches with ROCKCOTE Quick Render. Substrate must be wet down to assist with correct hydration and bonding. Application of ROCKCOTE Natural Materials may proceed once the “shine” has gone off the wall. Important: Ensure substrate does not contain any more than 15% moisture [WME] prior to the application of ROCKCOTE Natural Material. Additional Considerations: If total thickness of coating system is to exceed 8mm, contact ROCKCOTE

Technical Department. Important: The application of ROCKCOTE Natural Materials is a highly skilled process that requires

experience working with natural building products and systems. It is the responsibility of the applicator to select the right materials for the job and ensure correct installation and application according to the guidelines in the ROCKCOTE Natural Materials Systems Guide and the attached specification. ROCKCOTE strongly recommends that all ROCKCOTE Natural Materials be applied by a licensed tradesperson who has extensive experience in applying the product for a similar application to the project at hand. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

FINISH 1st Step 2nd Step 3rd Step 4th Step

Lime Wash Lime Wash Lime Wash


Lime Plaster Basecote (optional)

Venetian Plaster Velvetina (1mm) Venetian Plaster Venetian Plaster

Repel


Marrakesh (2 – 3mm coat)

Marrakesh (2-3mm coat optional)





Black Soap


External Substrates

SAND & CEMENT RENDER ______________________________________________________________________________________ Adhesion Requirements: Surface must not be powdery and must be clean and free of dust, dirt, oil, salt,

mould, or any other contamination. Surface Preparation: Substrate must be clean and free of dust, oil, dirt, mould or any other contamination.

Repair any cracks, holes and other patches with ROCKCOTE Quick Render. Substrate must be wet down to assist with correct hydration and bonding. Application of ROCKCOTE Natural Materials may proceed once the “shine” has gone off the wall. Important: New Site Mix Cement render should be fully cured for 28 days. Ensure substrate does not

contain any more than 15% moisture [WME] prior to the application of ROCKCOTE Natural Materials. Additional Considerations: If total thickness of coating system is to exceed 8mm, contact ROCKCOTE

Technical Department. Important: The application of ROCKCOTE Natural Materials is a highly skilled process that requires

experience working with natural building products and systems. It is the responsibility of the applicator to select the right materials for the job and ensure correct installation and application according to the guidelines in the ROCKCOTE Natural Materials Systems Guide and the attached specification. ROCKCOTE strongly recommends that all ROCKCOTE Natural Materials be applied by a licensed tradesperson who has extensive experience in applying the product for a similar application to the project at hand. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Lime Wash AE Primer Lime Wash Lime Wash


Lime Plaster Basecote (optional)

Venetian Plaster Velvetina (1mm) Venetian Plaster

Venetian Plaster

Repel


Marrakesh (2 – 3mm coat)

Marrakesh (2-3mm coat optional)





Black Soap


External Substrates

PAINTED RENDER __________________________________________________________________________________________

Adhesion requirements: Check the adhesion of the existing coating on every wall and at least three metres over

the proposed application areas. Glossy and smooth surfaces should be sanded with a coarse grit sand paper to ensure a key for satisfactory adhesion. If the old paint is oxidised or chalky, apply an alkali-resistant, penetrating primer/sealer. Surface Preparation: Remove all loose materials. Any loose or peeling paint should be scraped back to a firm

and sound substrate to leave surfaces clean and free of dust, oil, dirt, salt, mould, or any other contamination. Apply the first step to entire surface to a thickness of 2mm leaving surface rough to provide a suitable key for application of the 2nd step. Considerations: Care must be taken, not to exceed the maximum film build recommendations, or cracking of the

dried film may occur. Important: The application of ROCKCOTE Natural Materials is a highly skilled process that requires experience

working with natural building products and systems. It is the responsibility of the applicator to select the right materials for the job and ensure correct installation and application according to the guidelines in the ROCKCOTE Natural Materials Systems Guide and the attached specification. ROCKCOTE strongly recommends that all ROCKCOTE Natural Materials be applied by a licensed tradesperson who has extensive experience in applying the product for a similar application to the project at hand. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Lime Wash Ecostyle Sealer Undercoat

Lime Wash Lime Wash




Velvetina (1mm)

Venetian Plaster

Venetian Plaster

Repel









Black Soap

*Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your gauging water mix for the first coat of

Lime

Plaster Basecote.


Internal Substrates

IMPORTANT INFORMATION _________________________________________________________________________________________________ Suitable Substrates:

For interior purposes, ROCKCOTE Natural Materials are suitable for use over many modern and traditional natural substrates including:

Plasterboard (New and Painted)

Brick and Block

Brick and Block Painted

Off-Form Concrete

Blueboard/Fibre Cement Sheeting

INEX Magnesium Board

Hempcrete

For a system specification for the following substrates, please contact ROCKCOTE Technical Department on 1300 736 668

AAC Panel

Straw Bale

Any unlisted substrate

Natural Materials Suitable for Interior Use:

Lime Wash


Venetian Plaster

Marrakesh

Earthen Render Medium

Earthen Render Coarse

Clay Plaster Décor

Otsumigaki

Clay Paint


Internal Substrates

PLASTERBOARD NEW AND PAINTED _________________________________________________________________________________________________ Surface Preparation: All plasterboard joints must be set and sanded. Do not sand the paper face of plasterboard. Ensure

the surface is free of loose material. Wipe down to ensure the surface is clean, dry and dust free. For previously painted surfaces, if the total film build is to exceed 8mm, contact ROCKCOTE Technical Department for guidance. For previously painted surfaces, give a light sand and wipe off to remove dust prior to the next step. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Earthen Render (Medium or Coarse)

Ecostyle Sealer/Undercoat with grit


ROCKCOTE Repel (optional)

Clay Plaster Décor Ecostyle Sealer/Undercoat with grit

Clay Plaster Décor ROCKCOTE Repel (optional)

Clay Paint EcoStyle Sealer/Undercoat Clay Paint Clay Paint

Otsumigaki Ecostyle Sealer/Undercoat with grit

Otsumigaki Otsumigaki Liquid Carnauba Wax

Lime Wash Ecostyle Sealer/Undercoat Lime Wash Lime Wash

Lime Plaster Basecote Ecostyle Sealer/Undercoat with grit


Velvetina Ecostyle Sealer/Undercoat with grit

Velvetina (1mm) Velvetina (1mm) Liquid Carnauba Wax

Venetian Plaster Ecostyle Sealer/Undercoat with grit










Black Soap


Internal Substrates

BRICK AND BLOCK _________________________________________________________________________________________________

Adhesion requirements: If bricks/blocks are smooth faced and have very little or excessive absorption rates, apply a

scratch coat made from Lime Plaster Basecote or Earthen Render (the product that is used in the 1st step) mixed with Gauging Water Mix (25% ROCKCOTE Fast Bond to 75% water). Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.

Substrate must be wet down to assist with correct hydration and bonding. Application of ROCKCOTE Lime Plaster Basecote or Earthen Render may proceed once the “shine” has gone off the wall. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.






Clay Plaster Décor Earthen Render (Medium or Coarse)

Clay Plaster Décor ROCKCOTE Repel (optional)

Otsumigaki Earthen Render (Medium or Coarse)



Lime Wash Lime Wash




Lime Wash Lime Wash



Velvetina Lime Plaster Basecote


Venetian Plaster Lime Plaster Basecote










Black Soap


Internal Substrates

BRICK AND BLOCK PAINTED _________________________________________________________________________________________________

Adhesion requirements: Check the adhesion of the existing coating on every wall and at least three metres over the

proposed application areas. Glossy and smooth surfaces should be sanded with a coarse grit sand paper to ensure a key for satisfactory adhesion. If the old paint is oxidised or chalky, apply an alkali-resistant, penetrating primer/sealer. Surface Preparation: Remove all loose materials. Any loose or peeling paint should be scraped back to a firm and sound

substrate to leave surfaces clean and free of dust, oil, dirt, salt, mould, or any other contamination. Apply the first step to entire surface to a thickness of 2mm leaving surface rough to provide a suitable key for application of the 2nd Step. The 1st Step is intended as a scratch coat (excluding for Lime Wash). Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Earthen Render (Medium or Coarse) mixed with Gauging Water Mix*



Clay Plaster Décor Earthen Render (Medium or Coarse) mixed with Gauging Water Mix*


Clay Plaster Décor


Otsumigaki Earthen Render (Medium or Coarse) mixed with Gauging Water Mix*




Lime Wash Lime Wash




Lime Wash Lime Wash




Velvetina Lime Plaster Basecote mixed with Gauging Water Mix*

Velvetina (1mm) Velvetina (1mm)

Liquid Carnauba Wax



Venetian Plaster

Liquid Carnauba Wax











Black Soap

*Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your gauging water mix for the first coat of Lime Plaster

Basecote or Earthen Render.


Internal Substrates

OFF-FORM CONCRETE _________________________________________________________________________________________________

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination. Surface

must be wet down prior to the application of ROCKCOTE Lime Plaster Basecote or Earthen Render and once shine has gone, apply Lime Plaster Basecote or Earthen Render as per 1st Step. The 1st Step is needed as a scratch coat. Additional Considerations: If total thickness of coating system is to exceed 8mm, contact ROCKCOTE Technical

Department. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.



Earthen Render mixed with Gauging Water Mix*



Clay Plaster Décor

Earthen Render mixed with Gauging Water Mix*

Clay Plaster Décor

ROCKOTE Repel (optional)

Otsumigaki Earthen Render mixed with Gauging Water Mix*



Lime Wash Lime Plaster Basecote mixed with Gauging Water Mix*


Lime Wash Lime Wash




Velvetina Lime Plaster Basecote mixed with Gauging Water Mix*


Venetian Plaster



Venetian Plaster

Liquid Carnauba Wax









Black Soap


Basecote or Earthen Render.


Internal Substrates

BLUEBOARD / FIBRE CEMENT SHEETING _________________________________________________________________________________________________

Adhesion requirements: Blueboard sheeting must not contain more than 15% moisture (WME) prior to the application of

the ROCKCOTE System. Surface Preparation: Sheets must be installed strictly in accordance with manufacturer’s specifications.

Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch, tape and set all recessed joints with ROCKCOTE Patch & Prep and 150gsm Non Adhesive Alkali Resistant Mesh Tape. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

FINISH 1st Step (set joints)

2nd Step 3rd Step 4th Step 5th Step 6th Step


Patch & Prep and Mesh Tape

EcoStyle Sealer/ Undercoat with grit




Clay Plaster Décor




Clay Plaster Decor


Otsumigaki Patch & Prep and Mesh Tape




Lime Wash Patch & Prep and Mesh Tape



Lime Wash Lime Wash






Velvetina Patch & Prep and Mesh Tape


Velvetina (1mm) Velvetina (1mm)

Liquid Carnauba Wax

Venetian Plaster Patch & Prep and Mesh Tape



Venetian Plaster

Liquid Carnauba Wax













Black Soap


Basecote or Earthen Render as per first step.


Internal Substrates

INEX MAGNESIUM BOARD – For Application over Rough Side of Board _______________________________________________________________________________________ Adhesion requirements: Magnesium Board must not contain more than 15% moisture (WME) prior to the application of

the ROCKCOTE System. ROCKCOTE system to be applied over the rough side of Magnesium Board only. Surface Preparation: Sheets must be installed strictly in accordance with manufacturer’s specifications. ROCKCOTE

system is not to be applied over the smooth side of Magnesium Board. Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Patch, tape and set all recessed joints with ROCKCOTE Patch & Prep and 150gsm Non Adhesive Alkali Resistant Mesh Tape. General Considerations: typical data at 25 degrees celsius and 50% relative humidity.

Important: The application of ROCKCOTE Natural Materials is a highly skilled process that requires experience working

with natural building products and systems. It is the responsibility of the applicator to select the right materials for the job and ensure correct installation and application according to the guidelines in the ROCKCOTE Natural Materials Systems Guide and the attached specification. ROCKCOTE strongly recommends that all ROCKCOTE Natural Materials be applied by a licensed tradesperson who has extensive experience in applying the product for a similar application to the project at hand. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.

FINISH 1st Step

2nd Step 3rd Step 4th Step 5th Step 6th Step

Earthen Render (medium or coarse)


* Earthen Render (Medium or Coarse) mixed with Gauging Water Mix, with Mesh embedded



Clay Plaster Décor



Clay Plaster Décor


Otsumigaki Patch & Prep and Mesh Tape



Lime Wash Patch & Prep and Mesh Tape

* Lime Plaster Basecote mixed with Gauging Water Mix, with Mesh embedded


Lime Wash Lime Wash





Velvetina Patch & Prep and Mesh Tape


Velvetina (1mm)

Velvetina (1mm)

Liquid Carnauba Wax

Venetian Plaster



Velvetina Venetian Plaster

Venetian Plaster

Liquid Carnauba Wax

Marrakesh (Smooth, Trowel or Sponge Finishes, not Polished)


*Lime Plaster Basecote mixed with Gauging Water Mix, with Mesh embedded

Marrakesh (2-3mm)


Marrakesh (Lustre Polished finish)


*Lime Plaster Basecote mixed with Gauging Water Mix, with Mesh embedded

Marrakesh (2mm)

Marrakesh (2mm)

Black Soap

* Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your gauging water mix for the first coat of Lime Plaster Basecote or Earthen Render as per first step.


Internal Substrates

HEMPCRETE __________________________________________________________________________________________

Adhesion requirements: Substrate must not contain more than 15% moisture (WME) prior to the application of the

ROCKCOTE system. Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.


FINISH 1st Step

2nd Step 3rd Step 4th Step 5th Step

Earthen Render (medium or coarse)

Earthen Render (Medium or Coarse) with Mesh embedded



Clay Plaster Décor Earthen Render (Medium or Coarse) with Mesh embedded

Clay Plaster Décor


Otsumigaki Earthen Render (Medium or Coarse) with Mesh embedded


Lime Wash Lime Plaster Basecote with Mesh embedded


Lime Wash Lime Wash

Lime Plaster Basecote Lime Plaster Basecote mixed with Gauging Water Mix, with Mesh embedded


Velvetina Lime Plaster Basecote with Mesh embedded

Velvetina (1mm)

Velvetina (1mm)

Liquid Carnauba Wax

Venetian Plaster Lime Plaster Basecote with Mesh embedded

Velvetina Venetian Plaster

Venetian Plaster

Liquid Carnauba Wax

Marrakesh (Smooth, Trowel or Sponge Finishes, not Polished)

Lime Plaster Basecote with Mesh embedded

Marrakesh (2-3mm)



Lime Plaster Basecote with Mesh embedded

Marrakesh (2-3mm)

Marrakesh (2-3mm)

Black Soap


Wet Areas

IMPORTANT INFORMATION _________________________________________________________________________________________________ Definition of Wet Area:

Wet areas are defined as areas within a building, supplied with water from a water supply. ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster are suitable for walls in wet areas but not recommended for areas where water pools such as floors, shower floors, bath tubs or hand basins. ROCKCOTE Marrakesh is suitable for shower walls and splashbacks in

wet areas. Their successful application requires an exceptional level of skill and experience.

Important Information about ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster:

ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster are produced at a consistent high quality by ROCKCOTE, therefore we recommend that these products be applied by a licensed tradesperson who has extensive experience in applying these products for similar applications to your particular project. The success of each project requires the tradesperson to have a thorough technical knowledge of appropriate building design, substrate conditions and their client expectations to determine if Marrakesh or Venetian Plaster are fit for the purpose expected for your particular project.

Suitable Substrates:

For wet areas, ROCKCOTE Natural Materials are intended for use over the following substrates only:

Fibre Cement Cladding Designed Specifically for Wet Areas eg. Villaboard

Brick and Block

Off-Form Concrete

They are not suitable for any other substrates in wet areas. All wet areas must comply with your local building regulations for waterproof certification prior to the application of these products.

Natural Materials suitable for use in wet areas (note above ‘Definition of Wet Areas’):

Marrakesh

Venetian Plaster

Lime Plaster Basecote and Velvetina are suitable as a base coat only


Wet Areas

FIBRE CEMENT CLADDING DESIGNED SPECIFICALLY FOR WET AREAS _________________________________________________________________________________________________

Wet Areas are defined as areas within a building supplied with water from a water supply. They include bathrooms, showers, laundries and toilets.

IMPORTANT INFORMATION ABOUT PRODUCT SUITABILITY FOR WET AREAS:

ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster are suitable for walls in wet areas but not recommended

for areas where water pools such as floors, shower floors, bath tubs or hand basins (note: Wet Areas - Important Information on page 16).

ROCKCOTE Marrakesh is suitable for shower walls and splashbacks in wet areas.

ROCKCOTE Lime Plaster Basecote is suitable as a base coat only.

ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster are produced at a consistent high quality by ROCKCOTE, therefore we recommend that these products be applied by a licensed tradesperson who has extensive experience in applying these products for similar applications to your particular project. The success of each project requires the tradesperson to have a thorough technical knowledge of appropriate building design, substrate conditions and their client expectations to determine if Marrakesh or Venetian Plaster are fit for the purpose expected for your particular project.

ROCKCOTE does not recommend the use of any ROCKCOTE Natural Materials for floors. _________________________________________________________________________________________________

Adhesion requirements: The installed sheeting must not contain more than 15% moisture (WME) prior to the application

of the ROCKCOTE System. Surface Preparation: Sheets must be installed strictly in accordance with manufacturer’s specifications.

Substrate must be clean and free of dust, dirt, oil, salt, mould or any other contamination. Considerations: All wet areas must comply with your local building regulations for waterproof certification prior to the

application of these products. The finished product must be very well sealed, without any ‘open’ or rough surfaces where water and dirt can collect. Please read all relevant Technical Data Sheets & Safety Data Sheets prior to product use.


Venetian Plaster * Lime Plaster Basecote mixed with Gauging Water Mix (fully meshed)

Velvetina (1mm)

Venetian Plaster

Venetian Plaster

Liquid Carnauba Wax


* Lime Plaster Basecote mixed with Gauging Water Mix (fully meshed)

Marrakesh (2mm)

Marrakesh (2mm)

Black Soap

* Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your Gauging Water Mix for the first coat of Lime

Plaster Basecote.


Wet Areas

BRICK AND BLOCK _________________________________________________________________________________________________

Wet Areas are defined as areas within a building supplied with water from a water supply. They include bathrooms, showers, laundries and toilets.

IMPORTANT INFORMATION ABOUT PRODUCT SUITABILITY FOR WET AREAS:





ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster are produced at a consistent high quality by ROCKCOTE, therefore we recommend that these products be applied by a licensed tradesperson who has extensive experience in applying these products for similar applications to your particular project. The success of each project requires the tradesperson to have a thorough technical knowledge of appropriate building design, substrate conditions and their client expectations to determine if Marrakesh or Venetian Plaster are fit for the purpose expected for your particular project. ROCKCOTE does not recommend the use of any ROCKCOTE Natural Materials for floors. _________________________________________________________________________________________________

Additional Requirements: If total thickness of coating system is to exceed 8mm, contact ROCKCOTE Technical

Department.

Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.

Substrate must be wet down to assist with correct cement hydration and bonding. Application of ROCKCOTE Lime Plaster Basecote may proceed once the “shine” has gone off the wall. Considerations: All wet areas must comply with your local building regulations for waterproof certification prior to the



Venetian Plaster Lime Plaster Basecote mixed with Gauging Water Mix (fully meshed)*

Velvetina (1mm)

Venetian Plaster

Venetian Plaster

Liquid Carnauba Wax


Lime Plaster Basecote mixed with Gauging Water Mix (fully meshed)*

Marrakesh (2mm)

Marrakesh (2mm)

Black Soap

*Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your Gauging Water Mix for the first coat of Lime

Plaster Basecote.


Wet Areas

OFF FORM CONCRETE _________________________________________________________________________________________________

Wet Areas are defined as areas within a building supplied with water from a water supply. They include bathrooms, showers, laundries and toilets. IMPORTANT INFORMATION ABOUT PRODUCT SUITABILITY FOR WET AREAS:





ROCKCOTE Marrakesh and ROCKCOTE Venetian Plaster are produced at a consistent high quality by ROCKCOTE, therefore we recommend that these products be applied by a licensed tradesperson who has extensive experience in applying these products for similar applications to your particular project. The success of each project requires the tradesperson to have a thorough technical knowledge of appropriate building design, substrate conditions and their client expectations to determine if Marrakesh or Venetian Plaster are fit for the purpose expected for your particular project. ROCKCOTE does not recommend the use of any ROCKCOTE Natural Materials for floors. _________________________________________________________________________________________________

Additional Requirements: If total thickness of coating system is to exceed 8mm, contact ROCKCOTE Technical

Department. Surface Preparation: Substrate must be clean and free of dust, dirt, oil, salt, mould, or any other contamination.

Considerations: All wet areas must comply with your local building regulations for waterproof certification prior to the



Venetian Plaster Lime Plaster Basecote mixed with Gauging Water Mix* (fully meshed)

Velvetina (1mm)

Venetian Plaster

Venetian Plaster

Liquid Carnauba Wax


Lime Plaster Basecote mixed with Gauging Water Mix* (fully meshed)

Marrakesh (2mm)

Marrakesh (2mm)

Black Soap

*Gauging Water Mix: Use 25% ROCKCOTE Fast Bond to 75% water to complete your Gauging Water Mix for the first coat of Lime

Plaster Basecote.

http://www.rockcote.com.au/




Information provided in this booklet was correct as at 16 ... Systems... · Information provided in...

Documents

Transcript of Information provided in this booklet was correct as at 16 ... Systems... · Information provided in...