INFINITY FIXTURE INSTALLATION INSTRUCTIONS
Transcript of INFINITY FIXTURE INSTALLATION INSTRUCTIONS
![Page 1: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/1.jpg)
INTRODUCTION:CAREFULLY READ THE CONTENTS OF THESE INSTRUCTIONS, AS THE INSTRUCTIONS INDICATE THE CORRECT STEP BY STEP PROCEDURE TO ASSEMBLE THE PRODUCT. IN THE EVENT OF ASSEMBLY PROBLEMS OR MISSING PARTS, PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 616-842-5330.
CAUTION:ASSEMBLED UNIT IS VERY HEAVY. DO NOT ATTEMPT TO LIFT OR MOVE WITHOUT ASSISTANCE.
THE MANUFACTURER OF THIS DISPLAY ASSUMES NO LIABILTY FOR INJURY CAUSED BY IMPROPER ASSEMBLY/INSTALLATION OF THIS DISPLAY.
TOOLS REQUIRED:
#2 PHILIPS BIT + DRIVERCARPENTER LEVEL7/16” WRENCH*NOTE: DO NOT use impact driver on screws*
INFINITY FIXTURE INSTALLATION INSTRUCTIONS
2‐19‐2018 1
Step 1. remove skid board, see notes
![Page 2: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/2.jpg)
Telescoping Fixture Adjustment
2‐19‐2018 2
1.) Loosen Lock Knobs 2.) Adjust Fixture to Height 3.) Tighten Lock KnobsWhen the fixture is at the desired height, the lock knobs MUST be tightened.
THE MANUFACTURER OF THIS DISPLAY ASSUMES NO LIABILTY FOR INJURY CAUSED BY IMPROPER ASSEMBLY/INSTALLATION OF THIS DISPLAY.
![Page 3: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/3.jpg)
Slot Extension Brackets
2‐19‐2018 3
1. Insert “T” into slot 2. Rotate & push bottom into hole above lower leg
3. Push down flushwith lower leg
Slot Extension Bracket allows for a shelf to be placed at the point wherethe Infinity Fixture telescopes.
![Page 4: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/4.jpg)
Shelves
2‐19‐2018 4
Identify the shelves with a sticker on the front lip, and move to desired location.
Reverse steps for installation
MOVE THIS ROW
![Page 5: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/5.jpg)
Leveling Fixture
2‐19‐2018 5
Once fixtures are at desired height, the fixtures must be properly leveled, prior to connecting them.
![Page 6: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/6.jpg)
Installing Spacers
2‐19‐2018 6
Spacers are required when connect more than one fixture together.
All fixtures use ¼ inch spacers, located in the hardware kit attached to the fixture.
Insert spacers into uprights (3) on Lower Leg (1) on Upper Leg
![Page 7: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/7.jpg)
Fixture to Fixture Connection
2‐19‐2018 7
![Page 8: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/8.jpg)
Header Installation
2‐19‐2018 8
Headers are fixture width specific (ie. 2’ LED Header must install on a 2’ Fixture)
1.) Top row of shelves placed in 20th slot below Fixture Top Cap.
2.) Insert Header Assembly into Upright.
3.) Tighten Dowel Nut*
4.) Route cables and power. Plug into available outlet, or included power strip.
*Overtightening Dowel Nut may result in damage to Header Assembly teeth, or Dowel Nut itself.
20th Slot
![Page 9: INFINITY FIXTURE INSTALLATION INSTRUCTIONS](https://reader034.fdocuments.in/reader034/viewer/2022052020/6286a0a618a8a85e242d3797/html5/thumbnails/9.jpg)
Securing Fixture to the Wall
2‐19‐2018 9
Secure to wall using wall mount, screws, and anchors found in hardware kit.
Alternative mounting method: using wire cable, wall mount, screws and anchors.