ABOUT YOUR INFINEA TAB M® for iPHONE 6 PLUS CHARGING STATION (5-Unit)

ASSEMBLY

Infinea Tab® M for iPhone 6 PlusCharging Station(5-Unit)

QUICK START GUIDE

CHARGE STATUS2

TROUBLESHOOTING

CHARGING BAY

COOLING VENT

CHARGING CONTACTS

ATTACHMENT

LED INDICATOR

Infinea Tab M for iPhone 6 Plus Charging Station (5-Unit) - Standard Case

Infinea Tab M for iPhone 6 Plus Charging Station (5-Unit) - Rugged Case

1. Place the Infinea Tab M for iPhone 6 Plus Charging Station on a sturdy, clean and dry surface in an open, well-ventilated area away from direct sunlight.

2. Insert the included AC adapter plug into the DC Jack Port on the charger. Then connect the AC power adapter to a power outlet.

3. Insert the Infinea Tab M for iPhone 6 Plus unit into a charging bay, ensuring that the battery contacts are aligned with the bay’s contacts. The LED will light up to provide the charging status.

The Infinea Tab M for iPhone 6 Plus Charging Station (5-Unit) uses a tricolor LED to indicate the charge status.

Check the status LED on each slot to verify normal charging status. When the battery is fully charged, the LED indicator will be green.

Status Indicator LEDS

Green Inserted device is fully charged.

Orange Inserted device is charging.

Flashing Red Over-current protection is enabled. Charging bay is at or above maximum current fault (1.9A) and has stopped working.

Solid Red Over-current protection is enabled due to overheat fault (over 0°C/140°F).

No LED Indicates there is no device in charging bay or there is no power supply attached the charger.

Note 1: When the LED is solid red and the operating temperature has decreased to at or below 55°C/131°F, the charging bay will begin working again.

Note 2: No LED may also indicate over-current protection is enabled if the charging pins are shorted, or there is no load.

The LED does not come on when a unit is inserted.

• Ensure that the power supply is fully plugged into the outlet and plugged into the DC port.

It takes an excessive amount of time to fully charge the battery.

• Verify ambient temperature meets the operating temperature requirements.Operating: 0°C – 40°C (32°F – 104°F)

There are no accessories currently available for the Infinea Tab M for iPhone 6 Plus Charging Stations. Please visit our website at ipcmobile.com, or contact your Infinite Peripherals (IPC) account representative, for additional information about our current and future product accessory offerings.

ACCESSORIES

Mobility Sales/Technical Center Infinite Peripherals, Inc. 17681 Mitchell NIrvine, CA 92614Toll-Free: (866) 278-7860 Office: (949) 222-0300

Headquarters/Main Warehouse Infinite Peripherals, Inc. 2312 Touhy Ave.Elk Grove Village, IL 60004 Toll-Free: (800) 278-7860 Office: (847) 818-1260Fax: (847) 818-1287

Infinea is a registered trademark of Infinite Peripherals, Inc.

Technical Support Infinite Peripherals, Inc. 17681 Mitchell N Irvine, CA 92614Toll-Free: (866) 278-7860 Office: (949) 222-0300

Emailinfo@ipcmobile.com

Websiteipcmobile.com

•

Note: Box contents and part numbers may vary based on order configuration.

WARRANTYInfinite Peripherals (IPC) does not warrant, and is not responsible for,

any damage to the Infinea Tab M for iPhone 6 Plus Charging Station

(“Product”) as a result of liquid or solid particle intrusion into the

Product or damage caused by dropping the Product. If a material

or workmanship defect arises with regard to any IPC product, and a

valid claim is received within the Warranty Period, IPC (at IPC’s sole

discretion) will (1) repair the Product using new or refurbished parts

or (2) replace the Product with a new or refurbished Product. For

purposes of this limited warranty, “refurbished” means a product or

part that has been substantially returned to its original specifications.

In the event of a defect, these are your exclusive remedies.

QSG-10021 Rev. A

WARNINGS & CAUTIONSPlease observe the following precautions:

• Do not immerse the charger in water.

• When not in use, store the charger in a cooldry place.

• Do not store or operate the charger near aheat source.

• Do not directly connect the charger to anelectrical outlet.

• The charger should only be used for itsintended purpose.

• The output power drawn from the supplymust not exceed the rating for this product.

• The power to the device should be removedby unplugging the AC main plug.

• Do not use any other AC adapter otherthan the adapter supplied with this charger.Use of any other adapter may damage thecharger and will void the warranty.

ADDITIONAL INFORMATIONPlease contact your Infinite Peripherals sales representative for technical specifications and additional product documentation.