Inferno Fury Manual
-
Upload
john-burger -
Category
Documents
-
view
221 -
download
0
Transcript of Inferno Fury Manual
-
8/12/2019 Inferno Fury Manual
1/6
Arrow Precision, LLC
1619 W. Washington StreetAllentown, PA 18102
Email:[email protected]
Tel:610 437 7138
Fax:610 437 7139www.arrow-precision.com
arrowprecision
OutdoorsTM
Please keep for future reference
arrowprecision
OutdoorsTM
NOT A TOY. ADULT SUPERVISION REQUIREDl MISUSE OR CARELESS USE MAY CAUSE INJURY OR DEATHl THE RANGE OF THIS CROSSBOW COULD BE DANGEROUS UP TO 220 YARDSl THIS IS A HIGH POWER CROSSBOW INTENDED TO BE USED BY THOSE WHO ARE
18 YEARS OR OVER
l PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING
l PURCHASERS AND USERS SHOULD CONFORM TO GOVERNMENT LAWS AND THE
RESTRICTION OF THE OWNERSHIP OF CROSSBOWS
l NEVER ALLOW FINGERS/THUMB WITHIN THE STRING PATH
FOR YOUR OWN SAFETYl EYE PROTECTION STRONGLY RECOMMENDED
l DO NOT POINT AT ANYTHING OTHER THAN YOUR INTENDED TARGETl DO NOT LOAD YOUR CROSSBOW UNTIL YOU ARE READY TO SHOOT
l ONLY SHOOT WITH BOLTS INTENDED FOR THIS BOWl NEVER DRY FIRE (NEVER FIRE WITHOUT AN APPROPRIATE BOLT)THIS CAN CAUSE
DAMAGE TO THE PRODUCTl USING A DAMAGED STRING OR BOLT CAN BE DANGEROUS SINCE IT MAY CAUSE
FURTHER DAMAGE OR POSSIBLE INJURY TO THE USER OR OTHERS
SAFETY INFORMATION
FURY ASSEMBLY INSTRUCTIONS
and OWNERS MANUAL
CROSSBOWSArrow Precision, LLC reserves the right to change all product specications without notice.Actual product may vary from photographs. All performance specications are intended for guidance only.
C Arrow Precision, LLC
Version 1.1
-
8/12/2019 Inferno Fury Manual
2/6
PARTS LIST
5
1.175lb Fiberglass Limb2.Crossbow Body (Stock, Trigger Assembly,
Weaver Style Sight Base )
3.Crossbow String x 24.Crossbow Stringer Cable5.Foot Stirrup6.Hardware Package - Limb Tips (2)
Metal Pad (1) Concave Plastic Pad (1) Nose Bolt (1)
Foot Stirrup Screws (2) Allen Keys (3)7.Quick Detach Quiver
Congratulations on your purchase of the I nferno Fury 175lb Recurve Crossbow Package! Thank youfor purchasing our product, we hope you have many years of enjoyment from our crossbow package.
IMPORTANT- Please inspect your crossbow package to ensure that the following Items are
included in the box. (Phillips screwdriver required NOT included)
1
2
6
3
4
10
9
12
11
7
8
14
13
15
8. Quiver Hardware Packet Quiver Mount (1) Quiver Quick DetachMount (1) Phillips Head Screws
(2) Allen Head Screws (2)9. 4 x 16Bolts With Practice Points10. Padded Shoulder Sling With Attachments11. Rail Lube12. Eye Protection13. Open Sight14. 3-Dot Red Dot Sight15. Rope Cocking Device
Arrow Precision, LLC Inferno Crossbows and
Youth Archery Set One Year Limited Warranty
The manufacturer warrants the crossbow to be free from defects inmaterial and workmanship under normal use and service for 1 year from date ofpurchase. The warranty does not cover damage resulting from abuse or misuse, repairs or alterationsperformed by anyone other than the manufacturer or authorized service center, or damageoccurring in transit. Not covered are strings, cables, and other items which require periodic replace-
ment. Damage resulting from dry ring (ring unit without a bolt), whether intentional or accidental;including instances where the bolt is not seated properly resulting in damage to the limbs, cables,wheels, string, etc.For warranty service, the unit should be well packed to avoid damage in transit, including adescription of the difculty, and shipped postage prepaid to Arrow Precision, LLC at the address
below. Arrow Precision, LLC will repair or replace at no charge and return postage prepaid.For customers living outside the United States, Arrow Precision, LLC will provide standardwarranty service. However, inbound & outbound shipping cost is the responsibility of theconsumer. If failure was caused by misuse, alterations, accident, or abnormal conditions of operation,an estimate for repairs will be submitted for your approval prior to work being performed.Include a copy of the original sales receipt, along with the form below and mail toArrow Precision, LLC in order to register your product and activate your warranty.
If you have questions concerning this product or warranty, contact Arrow Precision, LLC and ask
for warranty assistance.
Arrow Precision, LLC
1619 W Washington Street
Allentown, PA 18102
Telephone (610) 437-7138
Fax (610) 437-7139
Email: [email protected]
www.arrow-precision.com
________________________________________________________________
Model Name __________________________ Date Purchased_________________
Last Name____________________________ First Name_____________________
Street Address____________________________________________________________
City_________________________________ State__________ Zip Code_____________
Email: __________________________________________________________________
Dealer Name__________________________ City ___________________ State_______
Price Paid_____________________________ Intended Use________________________
(hunting, target, other)
IN THE UNLIKELY EVENT YOU ARE MISSING ANY OF THESE PARTS CALL ARROW PRECISION, LLCIMMEDIATELY (610) 437-7138 or Email: [email protected] for immediate assistance.
DO NOT RETURN THE PRODUCT TO THE PLACE OF PURCHASE,
PLEASE CALL US DIRECTLY FOR SERVICE OR PARTS.
-
8/12/2019 Inferno Fury Manual
3/6
Step 2: Insert the concave plasticpad at the back of bow limb opening.Insert the limb then the metal plate withits rubber pad. Rubber to touch both
sides of the limb.
A: Objective End B: Windage Adjustment* C: Elevation Adjustment*
D: Battery Compartment Cap E: 7- Position Rheostart Knob
F: Eyepiece G: Locking Nuts
Step 1: Remove backing and stick onerubber to the at surface with one lip on
the concave plastic pad, as shown above.Stick another rubber onto the metal pad.
Step 5:Install the foot stirrup as shown,tighten both sides securely using theAllen Key.
Step 6:Install the limb tips to both endsof the limb, being careful to push and seatthe cover ALLthe way to avoid damageduring the stringing process.
ASSEMBLY INSTRUCTIONS:
Rubber
Metal PlateConcave
plastic pad
Rubber
Step 3:Insert the bow retaining screwand tighten by hand. Align the limb so thetwo vertical red lines are as centered as
possible on both sides of the opening.
Step 4: securely tighten the nose bolt
with the large Allen key.
Page 1Page 8
REPLACEMENT BATTERIES:
DURACELL DL2032, ENERGIZER ERC2032, ETC.
NOTE: Always remember to turn off the red dot sight when you have nished
using it. Always carry a replacement battery.
TAKING CARE OF YOUR RED DOT SIGHT
When not in use, the red dot sight should be kept in a clean and dry placeaway from any corrosive material. Never try to take the scope apart or clean itinternally. Send your scope to a qualied servi ce station if it ever needs repair. The lens
surface may be cleaned with a lens cloth.
A
G G
F
EC
D
B
* Remove the dust caps to adjust the sight
-
8/12/2019 Inferno Fury Manual
4/6
Step 3: Thread the bow string throughthe space between the stringer cableand limb tip on each side of the limb. Seat
the bow string loops over the limb tips asseen below.
Step 3: Move the anti-dry re switch
from the OFF to the ON position withyour index nger, hold, and then move
the safety catch with your thumb fromSAFE to FIRE. You cannot movethe safety catch unless the anti-dry re
switch is moved rst and held for safety
catch.
Pull back the stringer cable rmly enough
to alleviate tension. Pull the trigger while
maintaining pulling pressure on thestringer cable and gently let it down tothe resting position.
Step 4: Gently tug the stringer cableloops free from the limb ends. Be sureto retain the stringer cable for future use.
Step 1: Place the loops of the
nylon coated stringer cable over thelimb tips as shown in the picture below.
Step 2: Move the safety catch tothe FIRE position, place the footstirrup on the ground and cock thecrossbow using either your hands or the
rope cocking device .
Once cocked, the safety catch willautomatically switch from FIRE toSAFE.
SETTING UP YOUR RED
DOT SIGHT
CAUTION: BE SURE THAT THE
CROSSBOW IS NOT LOADED.
PRACTICE SAFE HANDLING
PROCEDURES AT ALL TIMES.
Installing a New BatteryThe red dot sight is powered by one
3V lithium coin style battery, type 2032.To install the battery, unscrew thebattery compartment cap on top of therheostat knob and insert the battery
(+) side up. Replace the battery cover. Ifthe red dot dims or does not light at all,replace the battery with a fresh one.
C A U T I O N :
SINCE ZEROING INVOLVES
THE ACTUAL SHOOT-
ING OF CROSSBOW BOLTS- IT SHOULD BE DONE AT
AN APPROVED RANGE OR
EQUALLY SAFE AREA. BE SURE
TO USE THE EYE PROTECTION
INCLUDED WHEN SHOOTING.
Initial Sighting
It is important to be sure that yourcrossbow is cocked centrally andconsistently in the same position eachtime it is red. We recommend that you
mark your string as shown on page 4.
Activate the red dot sight and adjustthe desired brightness by turning therheostat knob. The lower numbers
represent dimmer settings and thehigher numbers represent brightersettings of illumination. The 0position indicates that the unit is off.
Before you begin to start sighting, rst
remove the windage and elevationadjustment dust caps (as shownabove). Aim at a target 10 yards away,using the top dot on your site,
shoot two or three boltsbefore making any adjustments.
If the site needs adjusting, adjust the
top red dot towards the error. Forexample, if your three shots form apattern which is left and above theintended target, move your top red dot
right and down from the shot pattern.
Once your top dot is sighted in you canmove on to determine the range of thecenter dot and bottom dot. When the
top dot is sighted at 10 yards the centerdot will fall in at approximately 20 yardsand the bottom dot roughly 28 yards.Shoot bolts in groups of two or three
until your shot pattern is consistentlyhitting the desired target.
Of course this will be dependent on the
type and weight of bolt, tip and otheroutside inuences.
CAUTION: DIRECT VIEW-
ING OF THE SUN CAN CAUSE
DAMAGE TO YOUR EYE SIGHT
Thank you for your purchase. We wishyou great success in your hunting and
target shooting pursuits!
Page 2 Page 7
INSTALLING THE BOW
STRING Elevation
Windage
Anti-dryre switch
Safetycatch
-
8/12/2019 Inferno Fury Manual
5/6
ROPE COCKING DEVICEThe best way to cock the Inferno Furycrossbow is through the use of the
included rope cocking device. To use therope cocking device, simply grasp thehooks and drape the rope over the groovein the stock located behind the trigger
mechanism/scope mount and continue
to place the hooks onto the crossbowstring on each side of the ight track.Once this is accomplished, simply graspthe molded handles through the straps,
hold the crossbow on a level surface usingthe foot stirrup and pull the string backuntil it latches in the trigger mechanism.Using this method, the draw weight will be
reduced by 50% and the string will cock in aconsistent manner each time.
LOADING YOUR CROSSBOW
When loading a bolt into yourcrossbow, be sure to check that the
bolt is in good condition, is free fromdefects and is straight and true . It shouldlay in the ight track without any bends
or other issues that would cause erratic
ight of the bolt. Insert the bolt onto the
ight track with the index etching (odd
colored etching) down in the groove of
the ight track as pictured.
It is IMPERATIVE that the bolt isseated ALL the way back with the halfmoon nock cradled against the string.
If this is not done the string may jumpor go under the bolt which wouldbe equivalent to dry ring the bow
(Firing without a bolt will void your
warranty and damage could occur)
FIRING THE CROSSBOW
Ensure the bolt is correctlyloaded and an appropriate target is inposition with adequate backstop.Release the automatic safety and pull thetrigger to re the crossbow. We recom-
mend you start sighting in your bow at amaximum distance of 10 yards inorder to be sure that your aim ison target. Once the crossbow is
sighted in at close range, furtherdistances may be attainable.
RECOMMENDED BOLTS
The Fury crossbow includes 4 x 162219 aluminum bolts equipped with125 grain practice points suitable fortarget shooting only. For hunting use
the tips must be changed for properhunting tips of the same grain weight.
If expandable broadheads are
legal in your area then we recommend theybe utilized. You may alter your bolt setupusing 20 carbon bolts with 100 grainpractice points available through your
Inferno dealer.
Page 3Page 6
IMPORTANT: BEFORE USE,
LUBRICATE THE STRING
SERVING AND RAIL. FAILURE
TO DO SO WILL RESULT IN THE
STRING SERVING BURNING AND
WEARING OUT PREMATURELY.
UNDERSTANDING THE
ANTI DRY FIRE TRIGGER
Anti-dry re switch will always be in
the ON position when not cocked.
Once cocked two actions willhappen simultaneously: the anti-dryre switch will move from ON to
OFF and the safety catch will movefrom FIRE to SAFE automatically.
There are two ways touncock your crossbow successfully:
1) Loading the crossbow with a bolt andshooting into an appropriate discharge
target. This action will disengage theanti-dry safety mechanism which willallow you to move the safety catch fromSAFE to FIRE.
2)To uncock the crossbow withoutthe need of loading a bolt; move the
anti-dry re switch from OFF to the
ON position with index nger, hold,
and then move the safety catch with
your thumb from SAFE to FIRE. Youcannot move safety catch unless theanti-dry re switch is moved rst and
held for safety catch. Pull back on
the string rmly enough to alleviatetension. Pull the trigger while maintainingpulling pressure on the string and gentlylet down to the resting position.
COCKING THE CROSSBOW
Place the foot stirrup on the ground ina at and stable area. Insert your foot
into the stirrup and securely hold thecrossbow down to the ground with theweight of your body. With one hand on
each side of the ight track, securely
grasp the string as close as possible tothe ight track. Draw the string back
towards the trigger mechanism,
ensuring the string is in contact with theight track.
WARNING DO NOT DRY FIRE
THE CROSSBOW (FIRE WITH
NO BOLT) DAMAGE WILL
OCCUR AND VOID YOUR
WARRANTY.
Safety catch
ONCE COCKED
When cocked theanti-dry re switch
will move fromON to OFF,and the safety catchfrom FIRE to theSAFE position.
Anti-dry re switch
-
8/12/2019 Inferno Fury Manual
6/6