Industrial Const
Transcript of Industrial Const
-
8/16/2019 Industrial Const
1/34
SEMINAR ON
INDUSTRIAL CONSTRUCTION
-
8/16/2019 Industrial Const
2/34
INDUSTRIAL CONSTRUCTION
INTRODUCTION:
Industrial construction consist of the buildings including terrace factoriesor worsho!s" detached factories" warehouse" factor# canteens" $arets"hawer centers" s!orts halls" industrial training centers" etc%arecharacteri&ed
b# large clear o!en s!aces under light roof structures%
TYPE OF STEEL STRUCTURES
The usual for$s of roof structures are triangulated truss frames, lattice
girders and solid web portal frames and their choice de!ends considerabl#
on the e'tent of clear floor s!ace% Truss frames or lattice girders are usuall# $ore econo$ical in ter$s of
$aterial re(uired% Portal frames are chea!er to fabricate faster in construction and ha)e
ad)antages in aesthetic" ease of $aintenance and added headroo$"unobstructed b# ties or bracing $e$bers%
-
8/16/2019 Industrial Const
3/34
Portal frames
A portal frame is distinguised !" te rigid #onne#tion of te raftersto te $osts of te frame so tat under load moments are distri!utedtroug te rafter and te $ost%
T"$es of $ortal frames:
* Reinforced concrete !ortal fra$es
* Steel !ortal fra$es
* Ti$ber !ortal fra$es
-
8/16/2019 Industrial Const
4/34
Steel $ortal frames:
Short + $ediu$ s!an fra$es
Long s!an fra$es
Short and $ediu$ s!an fra$es the
a!e' or ridge" where the rafters
connect" is generall# $ade as an on,
site" rigid bolted connection for
con)enience in trans!orting half
!ortal fra$es %
Short,s!an !ortal fra$es $a# be fabricated off site as one fra$e% Mediu$,s!an
!ortal fra$es are generall# fabricated in two hal)es for ease of trans!ort and are
asse$bled on site with bolted connections of the rafters at the ridge" with high
strength friction gri! bolts%
Bolted conne
ction
Bolted connection
Short,s!an !ortal fra$e
Rafters & posts from same
Section of steel beam
-
8/16/2019 Industrial Const
5/34
In long s!an steel !ortal fra$es the
!osts and lowest length of the rafters"
towards the nee" $a# often be fab
ricated fro$ cut and welded I,sections so that the !ost section and !art of the
rafter is wider at the nee than at the
base and ridge of the rafter%
Long%s$an $ortal frames
Long s!an steel !ortal fra$es ha)e
the connection of the rafters to the !osts
at the nee" haunched to $ae the
connection dee!er than the $ain raftersection for additional stiffness%
The haunched connection of the
rafters to the !osts can be fabricated
either b# welding a cut I,section to the
underside of the rafter" as illustrated in
gi)en -ig" or b# cutting and bending
the botto$ flange of the rafter and
welding in a steel gusset !late%
-
8/16/2019 Industrial Const
6/34
The .unction of the rafters at the
ridge is often stiffened b# welding
cut I,section to the underside of the
rafters at the bolted site connection
Steel !ortal fra$es $a# be fi'ed to or !inned to bases to foundations% -orshort s!an !ortal fra$es" where thereis co$!arati)el# little s!read at thenee or haunch" a fi'ed base is oftenused% It will be seen fro$ that the steel
base !late" which is welded throughgusset !lates to the !ost of the !ortalfra$e" is set le)el on a bed of ce$entgrout on the concrete !ad foundationand is secured b# four holding,down
bolts set or cast into the concretefoundation%
-
8/16/2019 Industrial Const
7/34
A !inned base is $ade b# sitting the
!ortal base !late on a s$all steel
!acing on to a se!arate base !late
bearing on the concrete foundation%
/ortal fra$es with a s!an of u! to 01$
are defined as short s!an" fra$es with a
s!an of 02$ to 31$ as $ediu$ s!an and
fra$es with a s!an of 32$ to 24$ as
long s!an%
-
8/16/2019 Industrial Const
8/34
*Co$binations of slender ti$ber sections glued and nailed together" are used in
!ortal fra$es for $ediu$, and long,s!an roofs for such buildings as churches"
asse$bl# halls" s!orts halls and other single store# structures where the ti$ber
!ortal fra$es are e'!osed for a!!earance sae%
*The ad&antages of ti$ber as a structural $aterial in this for$ are its low self
weight and the co$!arati)el# little $aintenance re(uired to !reser)e and $aintainits strength and a!!earance%
*S"mmetri#al%$it# glued laminated tim!er $ortal : These !ortal fra$es are
usuall# fabricated in two sections for ease of trans!ort and are bolted together at
the ridge%These co$!arati)el# e'!ensi)e !ortal fra$es are s!aced fairl# widel# a!art to
su!!ort ti$ber or steel !urlins which can be co)ered with an# of the sheet
$aterials" slates or tiles%
TI'(ER PORTAL FRA'E
-
8/16/2019 Industrial Const
9/34
Light weight roof covering on
225x50 timber purlins
cramp
Cavity wall
Span 14.5 m
loor slab
Shoes bolte! to concrete base
Laminations taper
"0 !eg slope20 !ia bolt
oot of portal frame insi!e cast iron shoe
*The la$inations of ti$ber
fro$ which the !ortal is
$ade are arranged to ta!er in
both the rafter and the !ostso that the de!th is greatest at
the nee" where the fra$e
tends to s!read under load"
and slender at the a!e' or
ridge and the foot of the !ost"where least section is
re(uired for strength and
rigidit#%
-
8/16/2019 Industrial Const
10/34
EINFO CED CONC ETE PO TAL F AME
/re,cast reinforced concrete !ortal fra$es was su!!lied for the econo$ic
benefit of re!etiti)e casting in standard $oulds and close control of $i'ing"
!lacing and co$!action of concrete that is !ossible in factor# conditions%
-or con)enience in casting" trans!ort and erection on site" !re,cast concrete !ortal fra$es are generall# cast in two or $ore sections which are bolted
together on site either at the !oint of contra fle'ure in rafters or at the .unction
of !ost and rafter" or both%
-
8/16/2019 Industrial Const
11/34
-
8/16/2019 Industrial Const
12/34
The !oint of #ontrafle)ure is that !osition along the rafters
where negati)e or u!ward bending changes to !ositi)e ordownward bending% At this !oint the $e$ber is !resu$ed to be
suffering no bending stresses so that structurall# this is the
soundest !oint to $ae a connection%
Concrete !ortal fra$es are usuall# s!aced at fro$ 4.5 to
6.0m a!art to su!!ort !re,cast reinforced concrete !urlins and
sheeting rails" cast in lengths to s!an between fra$es and
hooked or bolted to the rafters and !osts% As an alternati)e
cold,for$ed steel 5ed !urlins and sheeting rails $a# be used forthe fi'ing of !rofiled steel sheeting%
-
8/16/2019 Industrial Const
13/34
The bases of concrete portal frames are placed in
mortices cast in concrete pad or strip foundations and
routed in position!
-
8/16/2019 Industrial Const
14/34
#etails ot a two$bay
symmetrical pitch concrete
portal frame.
It will be seen that the
rafter, which is cast as
one unit, is bolted to the
posts at the point of
contraflexure.
A single post supports
the rafter of the frames
below the valley in the
roof and these posts
are shaped to receive
a pre-cast reinforced
concrete valley
gutter, bolted to the
rafters, which is laid
without fall to rainwater
pipes and lined with felt.
-
8/16/2019 Industrial Const
15/34
The spacin of the internal columns belo" #alle$s ma$ be
increased b$ the use of a pre%cast concrete #alle$ beam to
support e#er$ other internal roof frame! The bul&$ #alle$ beam
"ill obstruct clear head room and add considerabl$ to the
cost of the structure! The disad#antae of this multiba$form of concrete portal frame is the number of comparati#el$
bul&$ internal columns obstructin a free "or&in area!
%he pre$cast reinforce! concretepurlins are usually of angle sectionwith stiffening ribs an! cast inlengths to span between portalframes. %he purlins are fixe! by
loops protru!ing from their en!swhich fit over an! are bolte! tostu!s cast in the rafters& with the 'oint being complete! with in$situ$cast cement an! san! mortar.
-
8/16/2019 Industrial Const
16/34
Corrugate! fibre cement sheeting is hoo( bolte! to
the concrete purlins over an insulating lining lai!
over the purlins. )s an alternative& profile! steel
sheeting with an insulating lining may be fixe! to *e!
purlins bolte! to the portal frames. +alls may
be of soli! bric(s or concrete bloc(s fixe! between
or across the posts of the portal frames& or
fibre cement or profile! steel sheeting may be
use!.
-
8/16/2019 Industrial Const
17/34
North Liht pre%cast reinforced concrete portal
frames construction
%he most economicalspan for this profile offrame is up to about,.0 m to minimi-e thevolume of roof space
insi!e the frames an!to avoi! the largesections of frame thatwoul! be necessaryfor greater spans.
%he south$facingslope is pitche! at220 an! the northfacing slope at 0 0to the hori-ontal.
-
8/16/2019 Industrial Const
18/34
A pre ' cast reinforced concrete #alle$ utter ma$ be
bolted to the frames!
-
8/16/2019 Industrial Const
19/34
-
8/16/2019 Industrial Const
20/34
) )
This is the $ost structurall#efficient and $ost co$$onl# usedt#!e of concrete !ortal fra$e% It
has been used for fa#tories*+areouses* !arns* seds and
single , store" $la#es ofasse$bl#% The slo!e of the rafters and
s!acing of !urlins and sheetingrails is usuall# arranged to suitfibre ce$ent or !rofiled steel
sheeting%
ADVANTAGES
The# could ra!idl# be trans!orted"erected and finished at an econo$iccost%
The# re(uire no $aintenance duringthe useful life of the building%
The fra$e has a so$ewhat betterresistance to colla!se during firesthan an un!rotected steel fra$e%
Due to the non,ductile nature ofconcrete of these fra$es" thead)antage of econo$# of section area
gained b# the use of the !lastic$ethod of design in the design ofsteel fra$es is considerabl# less withreinforced concrete%
-
8/16/2019 Industrial Const
21/34
Structural steel are !ivi!e! into two main groups accor!ing to the manufacture
process/
1ot rolle! sections
2%hose obtaine! by col! rolling.
%he former comprise of the heavier sections.
Steel components are use! in 5 ways/
1)s beams an! lintels for members which suffer ben!ing stresses.
2)s columns which resist compression an! ben!ing stresses.
")s ties where the stresses are tensile
4n roof trusses an! lattice gir!ers where the forces are compressive an! tensile&
an!5or reinforcement in reinforce! concrete.
Steel framework consists of beams& channels& angles& etc. %he
fastenings between the !ifferent parts of a frame is by means of bolts& rivets an!
wel!ing
Steel structures
-
8/16/2019 Industrial Const
22/34
North light truss and lattice gi
Up to the latter part of the nineteenth century themajority of single-storey buildings were of traditionalconstruction with timber, brick or stone walls supportingtimber-framed roofs covered with slate or tile. Thelimited spans, practicable with timber roofs, constrainedthe rapid expansion of manufacturing activitythat was occurring during the nineteenth century tomeet the demands of the rapidly increasing populationOf ngland and the very considerable export of !nished goods.
Industrial construction consist of the buil!ings
inclu!ing terrace factories or wor(shops& !etache!factories& warehouse& factory canteens& mar(ets&
haw(er centers& sports halls& in!ustrial training
centers& etc.
%hese are characteri-e! by large clear open
spaces un!er light roof structures
-
8/16/2019 Industrial Const
23/34
latticea reular eometric arranement of
points or ob*ects
an inter"o#en open%mesh frame made
b$ crisscrossin strips of "ood+ metal+
or plastic to form a pattern
,Lattice, is used in the sense of an
open rid or mesh of slender members
fi-ed across or bet"een each other+
enerall$ in some reular pattern
of cross%diaonals or as a rectilinear
rid!
lattice girders
-
8/16/2019 Industrial Const
24/34
The advantage of thissimple, single-storey,single bay frame iseconomy in the use of
materials by the use ofsmall section angle, tubularor "at standard mildsteel sections for thetrusses that can beeconomically fabricated and
#uickly erected.The disadvantages are3 very considerable volume of roofspace inside the triangular roofframes cannot be used for anypurpose other than housing
services such as lighting andheating,
3$here the activity enclosed by thebuilding re#uires heating, the roofspace has to be wastefully heated
as well as the useful space below.
-
8/16/2019 Industrial Const
25/34
-
8/16/2019 Industrial Const
26/34
% disadvantage of themulti-bayvalley beam form ofconstructionis that there is very limited
depth alongside the valley beamfor the fall &slope' of rainwaterpipesfrom valley gutter outlets to
rainwater down pipes !xedtointernal columns. Theshallowfall rain water pipes thatare run
alongside valley beams will
-
8/16/2019 Industrial Const
27/34
$ith increase in the spanof a triangular roof trussthe volume of unusedroof space and the roofframingincreases and it is,therefore, of advantageto combineseveral bays of the shedframe construction to
providecover with the leastvolume of roof space androof framing.
To minimi(e the number of internal columnsthat would otherwise obstruct the "oor, the )umbrella)or cantilever roof was adopted. *attice girders constructedat mid span in each bay support the trusses andwidely spaced internal columns in turn support thelattice girders to provide maximum unobstructed "oorspace
-
8/16/2019 Industrial Const
28/34
The lattice girdersupportshalf of each truss witheach half cantilevered
each sideof the truss, hence thename )cantilever truss)roof. The outline insection of the columnand the truss
cantileveredeach side of the latticegirder resembles anumbrella, hence thename )umbrella) roof.
-
8/16/2019 Industrial Const
29/34
To avoid sun glare andoverheating in summer the north lightroof pro!le was introduced, a lightsection steel roof truss asymmetrical inpro!le with the steeply sloping roof fullygla(ed and facing north.
disadvantage-
+orth light steel lattice trussconstructionoof lights in the slopes ofsymmetrical pitch roofs, whichare generally set in east and westfacing slopes, may causediscomfort through overheating insummer and disrupt
manufacturing activities by theglare from sunlight. To avoidthese possibilities the north lightroof is used. The north light roofhas an asymmetrical pro!le withthe south facing slope at / or
more to hori(ontal and the northfacing slope at from 01/ to
construction
North light truss
-
8/16/2019 Industrial Const
30/34
2ecause of the steep pitch ofthe north facing slope thespace inside the roof trussesof a north light roof is
considerably greater thanthat of a symmetrical pitchroof of the same span. Tolimitthe volume of roof space thatcannot be used and has to
be wastefully heated, mostnorth light roofs are limitedto spans of up to about1.1m
'saw-tooth' roof
-
8/16/2019 Industrial Const
31/34
'saw-tooth' roof
-
8/16/2019 Industrial Const
32/34
-
8/16/2019 Industrial Const
33/34
Joinery detailstruss member
-
8/16/2019 Industrial Const
34/34