INDIAN INSTITUTE OF MANAGEMENT INDORE figure In words Amount (In Rupees) BOQ Rate (In Rupees) no....

164

INDIAN INSTITUTE OF MANAGEMENT INDORE

TENDER DOCUMENT

VOLUME-II

(FINANCIAL PROPOSAL- ENVELOPE-III)

Name of Work: Annual/ Periodical maintenance & special repairs of Hostel Blocks, Faculty quarters, Staff residence type II, III, IV, Student residences 1 to 10, ER 2,3 utility 2& 3, pump house, certain area of Main building and construction of car parking at IIM Indore.

Chief Engineer Indian Institute of Management Indore Prabandh Shikhar, Rau-Pithampur Road, Indore 453556 (M.P) Phone : 0731-2439614, Website : http://www.iimidr.ac.in

In figure In words

1 Earth work

Earth work in excavation by mechanical means (Hydraulic excavator) /

manual means over areas (exceeding 30cm in depth. 1.5 m in width as well

as 10 sqm on plan) including disposal of excavated earth, lead unto 50m

and lift upto 1.5m, disposed earth to be leveled and neatly dressed

1.1 All kinds of soil 350.00 Cum

1.2 Ordinary rock 100.00 Cum

1.3 Hard rock (blasting prohibited) 100.00 Cum

Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides, ramming of bottoms, depth

unto 1.5 m, including getting out the excavated soil, and then returning the

soil as required, in layers not exceeding 20 cm in depth, including

consolidating each deposited layer by ramming, watering, etc. and

disposing of surplus excavated soil as directed, within a lead of 50 m All

kinds of soil for Pipes, cables etc. exceeding 80 mm dia. but not exceeding

300 mm dia

1.4 Pipes, cables etc. exceeding 80 mm dia. but not exceeding300 mm dia188.00 Rmt

1.5

Filling available excavated earth (excluding rock) in trenches, plinth, sides

of foundations etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and watering.

550.00 Cum

1.6

Filling with approved quality of Morrum brought from outside by the

contractor in trenches, plinth, sides of foundations etc. in layers not

exceeding 20cm in depth, consolidating each deposited layer by ramming

and watering.

1500.00 Cum

1.7

Supplying and laying with approved quality of red soil in ground in layers

not exceeding 20cm in depth, consolidating each deposited layer by

ramming and watering.500.00 cum

2 Conrete work

2.1

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to plinth level

Amount (In Rupees)

Indian Institute of Management Indore

BOQ Civil (Volume -2)Name of work:-Annual /Periodical maintenance & special repair of Hostel Blocks, Faculty quarters, Staff residence type II,III,IV Student residence, ER 2,3,utility 2 & 3, pump

house,Certain area of Main building and construction of car parking at IIM Indore

Rate (In Rupees)BOQ

no.Description Qty Unit

Page 1 of 22

In figure In wordsAmount (In Rupees)

Rate (In Rupees)BOQ


1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm

nominal size)100.00 Cum

2.2

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to plinth level

with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size)

10.00 Cum

2.3

Providing and laying cement concrete in retaining walls, return walls, walls

(any thickness) including attached pilasters, columns, piers, abutments,

pillars, posts, struts, buttresses, string or lacing courses, parapets, coping,

bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to

floor five level, excluding the cost of centering, shuttering and finishing with

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size)

4.20 Cum

2.4Centering and shuttering including strutting, propping etc. and removal of

form work for

Foundations, footings, bases for columns 76.90 sqm

2.5

Retaining walls, return walls, walls (any thickness) including attached

pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc 21.60 sqm

2.6 Columns, piers, abutments, pillars, posts and struts 1.00 sqm

3 Renforced cement concrete

3.1

Providing and laying in position specified grade of reinforced cement

concrete, excluding the cost of centering, shuttering, finishing and

reinforcement - All work up to plinth level

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm


3.2

Reinforced cement concrete work in walls (any thickness), including

attached pilasters, buttresses, plinth and string courses, fillets, columns,

pillars, piers, abutments, posts and struts etc. up to floor five level,

excluding cost of centering, shuttering, finishing and reinforcement

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm


3.3Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level

Thermo-Mechanically Treated bars 10000 Kg

3.4Add for plaster drip course/ groove in plastered surface or moulding to

R.C.C. projections.200 meter

3.5Centering and shuttering including strutting, propping etc. and removal of

form for :

Foundations, footings, bases of columns, etc. for mass concrete 189.00 Sqm

Page 2 of 22


Rate (In Rupees)BOQ


3.6Walls (any thickness) including attached pilasters, butteresses, plinth and

string courses etc. 900.00 Sqm

3.7 Suspended floors, roofs, landings, balconies and access platform 10.00 Sqm

3.8 Lintels, beams, plinth beams, girders, bressumers and cantilevers 67.58 Sqm

3.9 Columns, Pillars, Piers, Abutments, Posts and Struts 10.00 Sqm

Edges of slabs and breaks in floors and walls

3.10 Under 20 cm wide 50.00 meter

4 Brick work

4.1Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in

Cement mortar 1:4 (1 cement : 4 coarse sand) 39.36 Cum

4.2

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand) 11.04 Cum

4.3

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in superstructure above plinth level up to floor V level

Cement mortar 1:4 (1 cement :4 coarse sand) 100.00 sqm

4.4

P & F 200 wide chicken mesh of 12 mm mesh fixing in position with nails

at beam bottam and brickwork junction and coloumn and brickwork junction

etc complete.

200.00

5 Marble & Granite

5.1

Extra for providing opening of required size & shape for wash basin/ kitchen

sink in kitchen platform, vanity counter and similar location in

marble/Granite/stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete.

35.00 Nos

6 Wood &PVC Work

Page 3 of 22


Rate (In Rupees)BOQ


Providing and fixing factory made panel PVC door shutter consisting of

frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x

19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall

have a coat of steel primers of approved make and manufacture . M.S.

frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30

mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm

shall be tapered in 45 degree angle on both side forming styles and 5 mm

thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm

shall be tapered in 45 degree on the inner side to form top and bottom rail

and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm

shall be tapered on both sides to form lock rail. Top, bottom and lock rails

shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm

wide cross PVC sheet be provided as gap insert for top rail & bottom rail,

paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame

welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm)

thick15 mm wide PVC sheet beading on inner side, and joined together

with solvent cement adhesive. An additional 5 mm thick PVC strip of 20

mm width is to be stuck on the interior side of the 'C' Channel using PVC

solvent adhesive etc. complete as per direction of Engineer-in-charge,

manufacturer's specification & drawing.

6.1 30 mm thick plain PVC door shutters 34.02 Sqm

6.2

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel

plating and fixing with necessary screws etc., complete :- Overall width 50

mm

50.00 Rmt

6.3

Providing and fixing special quality bright finished brass cupboard or ward

robe locks with four levers of approved quality including necessary screws

etc. complete :- 40 mm

20.00 Nos

6.4Providing and fixing bright finished brass handles with screws etc.

complete:- 75 mm50.00 Nos

6.5

Providing and fixing wardrobe shutter 25 mm thick prelaminated board

/MDF(exterior grade) with one side decorative lamination of approved

shade with cutting and fixing in size with Nickel plated bright finished mild

steel piano hinges 1 mm thick 25 mm wide full length of ISI make of

approved colour and on another side of approved colour and brand with

beading/lipping of size 18 x 5 mm Patti and accessories like bright finished

brass handles 100 mm , cupboard lock (special quality chromium plated

brass cupboard locks with six levers of 50mm size), bright finished brass

tower bolts (barrel type of 100 x 10 mm ) including providing and fixing

6mm mirror (ISI make) 900 x 300 mm size as required all material of ISI

mark of approved brand etc. as required and directed by Engineer-In-

Charge.

100.00 sqm

6.6 Providing and fixing cupboard consisting of :

Page 4 of 22


Rate (In Rupees)BOQ


40x50 mm size second class teak wood frame

25 mm thick prelaminated waterproof plywood (exterior grade) with one

side decorative lamination of approved shade and the other side balancing

lamination shutters fixed with piano hinges.

18 mm thick prelaminated waterproof plywood (exterior grade) with one

side decorative lamination of approved shade and the other side balancing

lamination shelve and partition fixed and supported by aluminium angles.

20 mm dia brass hanger rod fixed with cp brass sockets

2 Aluminium handles of 100 mm size and one tower bolt of 150 mm size

inside the cupboard anodised and dyed to required shade.

one godrej make lock for locking arrangement

One mirror of 900 x 300 mm size fixed with S.S.hollow tubes

PVC lipping around the shutter

Exposed cut edges of 25 mm & 18 mm thick prelaminated waterproof

plywood to be sealed with M beading20.00 sqm

6.7 kitchen cabinate

40x50 mm size second class teak wood frame

25 mm prelaminated prelaminated waterproof plywood (interior grade) with

one side decorative lamination of approved shade and the other side

balancing lamination shutters fixed with prime hinges.

18 mm thick prelaminated waterproof plywood wiith one side decorative

lamination of approved shade and the other side balancing lamination

partition

4 Aluminium handles of 100 mm size anodised and dyed to required shade

45 x 12 mm teak wood moulding all along the teak wood frame

Spirit polishing of teak wood frame teakwood moulding

Exposed cut edges of 25 mm & 18 mm thick PVC lipping. 30.00 sqm

6.8

Dismantling doors, windows and clerestory windows (steel or wood) shutter

including chowkhats, architrave, holdfasts etc. complete and stacking within

campus.

Of area 3 sq. metres and below 100.00 each

6.9Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and

1.4 mm wide aperture with matching wood beading15.00 sqm

Page 5 of 22


Rate (In Rupees)BOQ


6.10

Providing and fixing in position WARD ROBE unit of size

1000mmx700mmx2000mm as per the approved drawings made up of 18

mm marine plywood conforming to IS:710,both side laminated

top,bottom,side,shelf,vertical, skirting, drawer facia, drawer back, drawer

side etc,with 18mm thick door and 9mm thick both side laminated drawer

bottom and back panel including necessary soft closing hinges, telescopic

slide, multipurpose lock, hanger rod of 25 mm dia ,16 gauge nickel plated

M.S. pipe ,2 nos tower bolts of barrel type having size 150 x10mm,4 nos

megnatic catcher triple stripal strip vertical type of approved quality, handle

250 mm,kd/minifix fittings, edges to be sealed with PVC edge bending tape

2.0mm thick of approved brand fixture and finishing etc.complete job.As per

approved shade and colour as per Engineer-in charge.

4.00 nos

6.11

Providing and fixing in position OVER HEAD unit on the wardrobe of size

1000mmx700mmx550mm as per the approved drawings made up of 18

mm thick Marine Plywood conforming to IS: 710, both side laminated

top,bottom,side,door,and 9mm thick both side laminated back panel

including necessary soft closing hinges, 96 mm handle,kd/minifix fitting,

edge to be sealed with PVC edge beding tape 2.00 thick of approved brand

fixture and finishing etc.complete job. as per Engineer in charge

4.00 nos

7 Steel work

7.1

Structural steel work riveted, bolted or welded in built up sections, trusses

and framed work, including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer all complete

1000.00 kg

7.2

Steel work in built up tubular ( round, square or rectangular hollow tubes

etc.) trusses etc., including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer, including welding and bolted with

special shaped washers etc. complete.

Hot finished welded type tubes 4800.00 kg

8 Flooring

8.1

Providing and laying 40mm thick machine cut stone flooring over 20mm

(average) thick base including pointing with cement mortar

1:2(1cement:2stone dust) with an admixture of pigment to match the shade

of stone with cement mortar 1:5(1cement:5coarse sand)including rubbing

the surface and plain polishing

a) Red sand stone 1000.00 sqm

8.2

Extra for nosing in steps and treads of red or white sand stone/ granite and

marbles kota steps or sills as per detail fine dressed and rubbed or

polishedred & whitesand stone for step & treads

200.00 meter

Page 6 of 22


Rate (In Rupees)BOQ


8.3

Kota stone slab flooring over 20 mm (average) thick base laid over and

jointed with grey cement slurry mixed with pigment to match the shade of

the slab, including rubbing and polishing complete with base of cement

mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick 250.00 sqm

8.4Extra for pre finished nosing in treads of steps of Kota stone/ sand stone

slab100.00 meter

.

8.5

Providing and laying 25mm thk kota stone sills for doors or windows in one

piece over 20mm (average )thick base laid over and joined with grey

cement slurry mixed with pigment to match the shade of the slab including

rubbing and polishing complete with 1:4(1cement:4coarse sand) etc

complete.

50 sqm

8.6

Polishing on existing surface in Kota stone work using machine on

counters, vanitres, Jambs, shevels, flooring etc. to give high glass finish

complete(old existing kota floor in toilets)

1500.00 sqm

8.7Mirror polishing on marble work/Granite work/stone work where ever

required to give high gloss finish complete.250.00 sqm

8.8

Providing and fixing Kota stone shelves 25mm thick in single piece in wall

in cement mortar 1:3 (1 cement: 3 coarse sand) including cutting chases in

walls and making good the walls including finishing complete56.00 sqm

8.9

Providing and fixing 18mm thick Granite mirror polished machine cut in

single piece over 1.00sqm but upto 2.00sqm for kitchen platforms,vanity

counters, facias and similar locations of required size of approved shade

colour and texture laid over 20mm thick base course bedding including cost

of slab of kota stone including joint with matching pigment epoxy touch ups

etc. at all levels

a) Granite telephone Black 60.00 sqm

8.10

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms, vanity

counters, window sills , facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high gloss finish etc. complete at

all levels.

Area of slab over 0.50 sqm 310.00 sqm

8.11

Providing edge moulding to 18 mm thick marble stone counters, Vanities

etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge

Page 7 of 22


Rate (In Rupees)BOQ


Granite work 380.00 meter

8.12

Providing and fixing stone slab with table rubbed, edges rounded and

polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions

by cutting a chase of appropriate width with chase cutter and embedding

the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate6 mm nominal size) as

per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade 10.80 sqm

8.13Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved make,

in all colours, shades except burgundy, bottle green, black of any size as

approved by Engineer-in-Charge, in skirting, risers of steps and dados,

over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade complete.75.00 sqm

8.14

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality conforming to

IS : 15622 of approved make & colour, laid on 20 mm thick cement mortar

1:4 (1 Cement : 4Coarse sand), including pointing the joints with white

cement and matching pigment etc., complete

62.00 Sqm

8.15

Providing and laying Vitrified tiles in different sizes (thickness to be

specified by the manufacturer), with water absorption less than 0.08% and

conforming to IS: 15622, of approved brand & manufacturer, in all colours

and shade, in skirting, riser of steps, laid with cement based high polymer

modified quick set tile adhesive (water based) conforming to IS: 15477, in

average 6 mm thickness, including grouting of joints (Payment for grouting

of joints to be made separately).

Size of Tile 1000x1000 mm 50.00 sqm

8.16

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy

grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of

hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge

Size of Tile 1000x1000 mm 50.00 sqm

9 Roofing

Page 8 of 22


Rate (In Rupees)BOQ


9.1

Providing and fixing tiled false ceiling of approved materials of size 595x595

mm in true horizontal level, suspended on inter locking metal grid of hot

dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side

inclusive) consisting of main "T" runner with suitably spaced joints to get

required length and of size 24x38 mm made from 0.30 mm thick (minimum)

sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm

made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between

main "T" at 600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30

mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm

panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm

and laying false ceiling tiles of approved texture in the grid including,

required cutting/making, opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended

from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm

fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI

adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm

spaced at 1200 mm center to center along main T, bottom exposed width

of 24 mm of all T-sections shall be pre-painted with polyester paint, all

complete for all heights as per specifications, drawings and as directed by

Engineer-in-charge. with GI Metal Ceiling Lay in plain Tegular edge Global

white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop;

made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive)

and electro statically polyester powder coated of thickness 60 microns

(minimum), including factory painted after bending

75.00 Sqm

10 Finishing

10.1 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) 315.18 Sqm

10.2

Painting with silicon & acrylic emulsion based water thinnable sealer of

approved brand and manufacture on wet or patchy portion of plastered

surfaces in Two coats

800.00 sqm

10.3

Washed stone grit plaster on exterior walls height upto 10 metre above

ground level, in two layers, under layer 12 mm cement plaster1:4 (1 cement

: 4 coarse sand ), furrowing the under layer with scratching tool, applying

cement slurry on the under layer @ 2 Kg of cement per square metre, top

layer 15 mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone

chipping 10 mm nominal size), in panels with groove all around as per

approved pattern, including scrubbing and washing the top layer with

brushes and water to expose the stone chippings ,complete as per

specification and direction of Engineer-in- charge (payment for providing

grooves shall be made separately).

50.00 sqm

Page 9 of 22


Rate (In Rupees)BOQ


10.4

Forming groove of uniform size in the top layer of washed stone grit plaster

as per approved pattern using wooden battens, nailed to the under layer,

including removal of wooden battens, repair to the edges of panels and

finishing the groove complete as per specifications and direction of the

Engineer-in-charge

15 mm wide and 15 mm deep groove 50.00 meter

10.5Applying one coat of water thinnable cement primer of approved brand and

manufacture on wall surface :

Water thinnable cement primer 1000.00 sqm

10.6With ready mixed red oxide zinc chromate primer of approved brand and

manufacture on steel galvanised iron/ steel works1000.00 sqm

10.7Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

Two or more coats applied @ 1.21 liter/10sqm. on new work or old work80000.00 sqm

10.8Wall painting with Velvet touch of Dulux/Asian/Berger paint of approved

brand and manufacture to give an even shade :

Two or more coats on new work/old work 9110.00 sqm

10.9Painting with aluminium paint of approved brand and manufacture to give

an even shade .

Two or more coats on new work/old work 600.00 sqm

10.10

Painting with synthetic enamel paint, having VOC (Volatile Organic

Compound) content less than 150 grams/ litre, of approved brand and

manufacture, including applying additional coats wherever required to

achieve even shade and colour.

Two coats 600.00 sqm

10.11

Providing and applying white cement based putty of average thickness 1

mm, of approved brand and manufacturer, over the plastered wall surface

to prepare the surface even and smooth complete. New or old work6400.00 sqm

10.12

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.

meters and under, including cutting the patch in proper shape, raking out

joints and preparing and plastering the surface of the walls complete,

including disposal of rubbish to the dumping ground within 50 metres lead

With cement mortar 1:4(1 cement:4 fine sand) 1140.43 sqm

10.13

Providing and fixing curtain rods of 1.25 mm thick brass plates with two

brass brackets fixed with brass screws and wooden plugs etc.wherever

necessary complete with 25 mm diameter

50.00 Rmt

Page 10 of 22


Rate (In Rupees)BOQ


10.14

Removing dry or oil bound distemper, water proofing cement paint like by

scrapping, washing and sand papering and preparing the surface smooth

including necessary repairs to scratches etc. complete

60000.00 sqm

10.15

Painting with synthetic enamel paint of approved brand and manufacture of

required colour to give an even shade: One or more coats on old work

including base prepration

10000.00 sqm

10.16

Applying Two coats damp proof coat on wall on exterior surface including

cleanning of existing surface of wall etc ( Asian/Berger/Dulux/Pidilite

make)as per manufacture specification

1000 sqm

10.17

Applying Three coats of damp proof coat on roof including cleanning of

existing surface of roof etc.( Asian/Berger/Dulax/Pidilite make)as per

manufacture specification

500 sqm

10.18

Applying Two coats damp block coat on wall on interior surface including

cleaning of existing surface of wall etc.( Asian/Berger/Dulax/Pidilite

make)as per manufacture specification

1000 sqm

10.19Finishing walls with Premium Acrylic Smooth exterior paint with Silicone

additives of required shade

Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm)over existing

cement paint surface18000.00 sqm

10.20

Dismantling stone slab flooring laid in cement mortar including stacking of

serviceable material and disposal of unserviceable material within 50

metres lead.

850.00 sqm

10.21

Dismantling & Removing old plaster or skirting raking out joints and

cleaning the surface for plaster including disposal of rubbish to the dumping

ground within 50 metres lead

1140.43 sqm

10.22

Demolishing cement concrete manually/ by mechanical means including

disposal of material within 50 metres lead as per direction of Engineer - in -

charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)69.75 Cum

10.23

Dismantling aluminium Doors ,windows,for changing damaged pannel

refixing with inserting new aluminum composite panel complete as per

direction of engineer-Incharge(Aluminium composite pannel will be paid

seprately)

15.75 sqm

10.24

Disposal of building rubbish / malba / similar unserviceable, dismantled or

waste materials by mechanical means, including loading, transporting,

unloading to approved municipal dumping ground or as approved by

Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts

involved.

100.00 cum

10.25Dismantling wall tiles and cleaning the surface disposal of rubbish to the

dumping ground within 50 metres lead98.50 sqm

Page 11 of 22


Rate (In Rupees)BOQ


10.26

Dismantling old wash basin,W/c, Urinals,including stacking of serviceable

material and disposal of unserviceable material within 50 metres lead. 50.00 each

10.27

Removing existing melamine polish by scrapping, sand papering and

preparing the surface smooth including necessary repairs to

scratches,holes, proper colour touching to give even colour etc. complete,

applying filler,sealer etc. as per specification.

2024.00 sqm

10.28

Providing two coat of Polyurethene Melamine polishing over two coat of

melamine sealer etc complete so as to make it water resistant on wood

work (on old work). The rate includes all material,tools and labour etc

complete as per the direction of Engineer in charge

2024.00 sqm

10.29Taking down existing door shutter and refixing after polishing of shutter

including fixing of all fixture complete506.00 each

10.30

Demolishing trimix RCC floor manually/ by mechanical means for trenches

including disposal of material within campus as per direction of Engineer -

in - charge.

5.00 cum

11 Road work/ Pathway work

11.1

Supplying and laying 65mm thick interlocking paver blocks of glazed finish

with rubber mould make laid over sand bedding of 50mm thick thoroughlly

compacted with compacting machine of 4T capacity after laying the blocks

of SUPER/ UNITY/ VIPURVA make or equivalent.

1400.00 Sqm

11.2

Taking out existing CC interlocking paver blocks from footpath/ central

verge, including removal of rubbish etc., disposal of unserviceable material

to the dumping ground, for which payment shall be made separately and

stacking of serviceable material wit

1249.00 sqm

11.3

Laying old cement concrete interlocking paver blocks of any design/ shape

laid in required line, level, curvature, color and pattern over and including

50 mm thick compacted bed of coarse sand, filling the joints with fine sand

etc. all complete as per the direction of Engineer in-charge. (Old CC paver

blocks shall be supplied by the department free of cost).

1249.00 sqm

12 Sanitary installations

12.1

Providing and Fixing white vitreous china pedestal type water closet with

seat and lid, 10 litre low level PVC flushing cistern with manually controlled

device (handle lever), CAT no 20011 of Hindware or equivalant make as

per approved by engineer in charge including jet, with all fittings and

fixtures complete including cutting and making good the walls and floors

wherever required(Price range of W.C. Rs 5000-5500/-)

a) W.C. Pan with ISI marked white solid plastic seat and lid (White colour) 20.00 each

Page 12 of 22


Rate (In Rupees)BOQ


12.2

Providing and Fixing white vitreous china wall hung water closet of CAT

no. FSS - WHT- 0113 of jaquar make or equivalent make as approved with

silim conceled cistern body CAT no CIB-WHT-31801011 XD with drain pipe

connection set for wall hung WC., with flushing plate CAT no. CIS-CHR-

31185210 X with all fittings and fixtures complete including cutting and

making good the walls and floors wherever required (Price Range Rs.

18000- 19000/-)

1.00 each

12.3

Providing and Fixing white vitreous china wall hung water closet of CAT

no. KUS - WHT- 0114 of jaquar make or equivalent as approved with slim

conceled cistern body CAT no CIB-WHT-31801011 XD with drain pipe

connection set for wall hung WC., withf lushing plate CAT no. CIS-CHR-

31185210 X of jaquar make or equevelant make all fittings and fixtures

complete including cutting and making good the walls and floors wherever

required (Price Range Rs. 18000- 19000/-))

1.00 each

12.4

Providing & Fixing white vitreous china flat back large half stall urinal of

630x400x420 mm mm sizes CAT no. 60002 of Hindware or equivalent

make as per approved brand fixed on CI bracket, spreaders, waste

coupling, heavy duty bottle trap, painting and brackets, cutting and making

good the wall surface completely. Make Perryware, Hindware, Johnson or

equivalent. Model and shade as approved by engineer incharge. All CP

Fittings to be of Jaguar or equivalent as approved (Price Range Rs. 7000-

8000/-)

20.00 each

12.5

Providing & Fixing wash basin of 160mmx580mm x450mm table top

florenite CAT no FLS-WHT-0575 of jaguar make or equivalent make as

approved with, 32 mm CP brass waste coupling of standard pattern,

heavy duty bottle trap,including painting of fittings & brackets cutting &

making good the wall wherever required., (Market range Rs 6800-6900)

including all accerioris

20.00 each

12.6Providing & Fixing toilet paper holder CAT no. AHS-1553 of jaquar make or

equivalent make (Price range Rs 1100-1200)

a) Stainless steel 15.00 Each

12.7

Providing & Fixing towel rail CAT no AKP - 35711P of jaquar make or

equivalent make of approved ,complete with brackets fixed to wooden

cleats with C.P brass screws.

a) towel rail with two C.P brass brackets 600 mm. Long (Price range Rs.

1600-1700/-)50.00 Each

12.8Providing and fiixng Soap dish CAT no. ACN-1131N of jaquar make or

equvelent make as approved (Price range Rs 400-450/-)50.00 Each

Page 13 of 22


Rate (In Rupees)BOQ


12.9

Providing & Fixing M.S.cloth hanging hooks patti having 5 hooks per patti

with rubber head with enamel paint of approved make including C.P brass

screws, washers good the wood work (As per existing in the rooms)

15.00 Each

12.10liquid soap dispenser of CAT no AKP-35735P of jaquar make or equevelant

make as approved (Price Range Rs 1100- 1200/-)100.00 Each

12.11

Providing and fixing mirror of superior glass (of approved quality) as per

CAT no CAN -1195 N of jaquar make or equivalent make as approved

Swivel Mirror( Price range Rs.1800-1900)

32.00 Each

12.12

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar

taps, 32 mm C.P. brass waste of standard pattern, including painting of

fittings and brackets, cutting and making good the walls wherever require

with White Vitreous China Angle back wash basin size 600x 480 mm with

single 15 mm C.P. brass pillar tap

32.00 Nos

12.13 Providing and fixing soil, waste and vent pipes :

100 mm dia 25.00 meter

Sand cast iron S&S pipe as per IS: 1729

12.14 75 mm diameter : 50.00 meter

Sand cast iron S&S pipe as per IS: 1729

Providing & Fixing bend of required degree with access door, insertion

rubber washer 3mm thick, bolts & nuts complete.

12.15 a) 100mm sand cast iron S&S 10.00 each

12.16 b) 75mm dia sand cast S&S 10.00 each

12.17 Providing & Fixing plain bend of required degree

a) 100mm sand cast iron S&S 10.00 each

12.18 b) 75mm dia sand cast S&S 10.00 each

12.19 Providing & Fixing heel rest sanitary bend


12.20 b) 75mm dia sand cast iron S&S 10.00 each

12.21 Providing & Fixing Y


12.22 b) 75mm dia sand cast iron S&S 10.00 each

12.23Providing & Fixing single equal plain junction of required degree with

access door insertion rubber washer 3mm thick, bolts & nuts complete.

a) 100x100x75mmSand cast iron S&S 10.00 each

12.24 b)75x75x75mm Sand cast iron S&S 10.00 each

12.25Providing & Fixing single single unequal junction of required degree with

access door, insertion rubber washer 3mm thick, bolts and nuts complete.

a) 100x100x75mm Sand cast iron S&S 10.00 each

12.26 Providing & Fixing terminal guard

Page 14 of 22


Rate (In Rupees)BOQ


100 mm Sand cast Iron S & S as per IS - 1729 10.00 each

12.27 75 mm Sand cast Iron S & S as per IS - 1729 10.00 each

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron

pipes & fittings of diameter:

12.28 a) 100mm 50.00 each

12.29 b) 75mm 50.00 each

12.30Providing & Fixing M.S stays & clamps for sand cast iron /centrifugally cast

(spun) iron pipes of diameter:

a)100mm dia 50.00 each

12.31 b) 75mm dia 51.00 each

12.32

Providing & Fixing trap of self cleansing design with screwed down or

hinged grating with or without vent arm complete including cost of cutting

and making good the walls & floors :

a) 100mm inlet&75mm outlet - Centrifugally Cast (Spun) Iron S&S 20.00 each

12.33 Cutting holes upto 30x30 cm in walls including making good the same.

a) With Modular bricks. 50.00 each

12.34Providing & Fixing stainless steel Jali (grating) with or without hole for

waste pipe for floor /Nahani trap.

a) 100mm dia weight not less than 100 gms. 20.00 each

13.0 Water supply

Providing & Fixing G.I pipes complete with G.I fittings & clamps, including

cutting & making good the walls etc.(internal work)

Exposed on wall

13.1 a)15mm dia nominal bore 60.00 meter

13.2 b)20mm dia nominal bore 50.00 meter

13.3 c)25mm dia nominal bore 40.00 meter

13.4 d)32mm dia nominal bore 10.00 meter

Providing & Fixing G.I pipes complete with G.I fittings & clamp (concealed

pipe including painting with anti corrosive bitumastic paint,cutting chases &

making good the wall.)

13.5 a)15mm dia nominal bore 50.00 meter

13.6 b)20mm dia nominal bore 40.00 meter

13.7 c)25mm dia nominal bore 30.00 meter

13.8 d)32mm dia nominal bore 10.00 meter

Providing & fixing brass gate valve with C.I wheel Half turn of approved

quality ( serewed end)

13.9 25 mm nominal bore 8.00 each

13.10 32 mm nominal bore. 8.00 each



Page 15 of 22


Rate (In Rupees)BOQ


13.13Providing and fixing salem stainless steel A ISI 304(18/9\8)kithchen sink

as per IS 13983 of Nirali / nelkanth of size 460x915x178 bowl depth 4.00 each

13.14Providing and fixing CP brass bib cock/ stop cock of approved quality

conforming to IS 8931.

13.15 a) 15mm nominal bore 20.00 each

Providing and fixing CP brass body bibcock Cat no. KUB 35037F of jaqur

make or equivalent make as approved by Engineer -in charge (Price

range 1200-1300)


Providing & fixing concealed stop cock of standard design CAT no. VGP -

81083 K of jaquar make or equivalent make as approved by engineer in

charge (Price range Rs. 450-500)


Providing & fixing angle valve of CAT no. FUS-29053 of jaquar make or

equivalent make as approved for basin and geyser points as per direction

of engineer - in charge (Price range Rs 80-900/-)


13.19

Providing & Fixing wall mixer CAT no FUS-29273UPR of Jaquar make or

equivalent as approved Complete as per direction of Engineer- incharge(

Price range Rs 3500-3600/-)

10.00 each

13.20

Providing &Fixing Health fauset CAT No.ALD-IVY-585 & Two way Bib cock

CAT No.KUB -35041F of jaquar makeor equivalent as approved . complete

as per the direction of Engineer- Incharge(Price Range Rs. 2400-2500/-)

10.00 each

13.21

Providing & fixing CP Brass pillar cock for basin KUB-35233FK wall

mounteed single lever basin mixer wall flange ,nipple and spout, with

concealed body cartridge sleeve CAT no. ALD-233 of jaquar make or

equiivalent make of approved make (Price range 5600-5700/-)

a) 15mm nominal bore 32.00 each

13.22Providing and fixing CP brass 32mm dia casted bottle trap complete in all

respect .jaquar /hindwareor equivalent make as approved20.00 each

13.23C.P. spreader with c.p. pipe jaquar /hindwareor equivalent make as

approved for urinals20.00 each

13.24Providing and fixing approved PVC connectors of required lenth to basin

and geyser. jaquar /hindwareor equivalent make as approved50.00 each

13.25

Providing and fixing overhead Shower CAT no. OHS 1789 of jaquar or

equivalent make of approved make with shower arm CP CAT no SHA

479L 450 of jaquar make (Price range Rs.2400-2500)

18.00 each

14 Drainage

14.1 Supplying and fixing C.I. cover without frame for manholes :

455x610 mm rectangular C.I. cover (light duty) the weight of the cover to

be not less than 23 kg20.00 each

Page 16 of 22


Rate (In Rupees)BOQ


14.2

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks

in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C.

vertical grating complete as per standard design With common burnt clay

F.P.S. (non modular) bricks of class designation 7.5

6.00 Nos

14.3

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :

10 graded stone aggregate 40 mm nominal size) up to haunches of S.W.

pipes including bed concrete as per standard design :

300 mm diameter 100.00 Rmt

14.4

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with

collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1

cement : 2 fine sand) including testing of joints etc. complete with 300 mm

dia. R.C.C. pipe

100.00 Rmt

15.0 Aluminium work

15.1

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/ appropriate Z

sections and other sections of approved make conforming to IS: 733 and

IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50

micron)100.00 kg

15.2

For shutters of doors, windows & ventilators including providing and fixing

hinges/ pivots and making provision for fixing of fittings wherever required

including the cost of EPDM rubber / neoprene gasket required (Fittings

shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

micron)200.00 kg

Page 17 of 22


Rate (In Rupees)BOQ


15.3

Designing,Fabricating, testing, installing and fixing in position curtan wall

with aluminium composite pannel cladding , with open groove for liner as

well as curvilinear portions of the buildings,for all heights and all levels etc.

including :

a) Structural analysis & design and preparation of shop drawings for

pressure equalisation or rain screen principle as required, proper drainage

of water to make it watertight including checking of all the structural and

functional design.

b) Providing, fabricating and supplying and fixing panels of aluminium

composite panel cladding in pan shape in metalic colour of approved shdes

made out of 4mm thick aluminium comsite panel material consisting of

3mm thick FR grade mineral core sandwiched between two Aluminium

sheets ( each 0.5mm thick). The aluminium composite panel cladding sheet

shall be coil coated, with Kynar 500 based PVDF/Lumiflon based

fluoropolymer resin coating of approved colour and shade on face #1 and

polymer (Service) coating on face #2 asspecified using stainless steel

screws, nuts,bolts,washers,cleats,weather silicone sealant,

backer rods etc.

c) The fastening brackets of Aluminium alloy 6005 T5/MS with Hot Dip

galvanised with serrations and serrated washers to arrest the wind load

movement, fasteners,SS316 Pins and anchor bolts of approved make in

SS 316,Nylon separators to prevent bi-metallic contacts all complete

required to perform as per specification and drawing.

The items includes cost of all material & labour components,the cost of all

mock ups at site,cost of all samples of individual components for testing in

an approved laboratory .field tests on the assembled working curtain wall

with alumnium composite panel cladding,cleaning and protection of curtain

wall with aluminium composite panel cladding till the handing over of

building for occuption. Base frame work for ACP cladding in payable under

the relevant aluminium item,s.The Contractor shall provide curtain wall with

aluminium composite panel cladding,having all the performance

characteristics all complete, as per the Architectural drawings, as per item

description, as specified,as per the approved shop drawings and as

directed by the engineer- in charge.However, for the purpose of payment

only the actual are on the external face of the curtain wall with aluminium

composite pannel cladding ( Including width of groove ) shall be measured

in sqm, up to two decimal places.

30.00 sqm

15.4 With float glass panes of 4.0 mm thickness 25.0 sqm

15.5 With tinted glass panes of 4.0mm thickness 50.00 sqm

Page 18 of 22


Rate (In Rupees)BOQ


15.6

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone

work by providing weather silicon sealant over backer rod of approved

quality as per architectural drawings and direction of Engineer-in-charge

complete

Upto 10mm depth and 10 mm width 400.00 meter

16.7

Providing and fixing anodised aluminium grill (anodised transparent or dyed

to required shade according to IS: 1868 with minimum anodic coating of

grade AC 15) of approved design/pattern, with approved standard

section and fixed to the existing window frame with C.P. brass/ stainless

steel screws @ 200 mm centre to centre, including cutting the grill to proper

opening size for fixing and operation of handles and fixing approved

anodised aluminium standard section around the opening, all complete as

per requirement and direction of Engineer-in-charge. (Only weight of

grill to be measured for payment).

350.00 kg

16.0 Miscellanious work

16.1

Providing and fixing double scaffolding system (cup lock type) on the

exterior side of building/structure, upto 25 metre height, above ground level,

including additional rows of scaffolding in stepped manner as per

requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre

centre to centre, horizontal & vertical tubes joint with cup & lock system

with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in

the scaffolding for working platform etc. and maintaining it in a serviceable

condition for execution of work of cleaning and/ or pointing and/ or applying

chemical and removing it thereafter. The scaffolding system shall be

stiffened with bracings, runners, connecting with the building etc, wherever

required, if feasible, for inspection of work at required locations with

essential safety features for the workmen etc., complete as per directions

and approval of Engineer-in-charge. Note:- (1) The elevational area of the

scaffolding shall be measured for payment purpose. (2) The payment will

be made once only for execution of all items for such works

2000.00 Sqm

Page 19 of 22


Rate (In Rupees)BOQ


16.2

Cleaning the sand stone surface and removing dirt, dust, bird dropping,

grease, oil, algae, fungus, monkey beats, vegetable growth etc., including

providing, applying and washing the surface with liquid Ammonia Chemical

of 5% solution and other chemical cleaning agent as approved by

Archaeological Survey of India/ Engineer-incharge, of approved brand and

manufacturer, with the help of required scrubbers and also cleaning with

machine operated water jet mixed with desired quantity of fine silica where

ever required, without causing any scratching/ damage to the stone surface

and finally washing the surface with clean water with the help of pressure

jet machine, complete in all respect, including taking all precautions to

safeguard ventilators, windows, doors etc. by suitable covering so as to

avoid any damage to the building/ structure, all as per direction of Engineer-

in-charge (The rate is inclusive of all materials & labours involved except

scaffolding).

2000.00 Sqm

16.3

Cleaning the RCC surfaces from dust dirt and cement slurry etc. by means

of wire brush dust removing brush scrapper etc. and wetting the surface

piror to application of tapecrete without free water standings Application of

1st coat of tapecreate acrylic polymer

a) Laying fibre glass cloth over the tapecrete applied surface upto 300mm

height of vertical walls when the first coating is still green and allowed to air

cure 4 hours Application of one coat of tapecrete brush topping coat over

the treated surface and allowed for air cure for at least 4(four) hours and

water curefor next two days

b) Laying 12mm thick cement plaster 1:4(1cement:4coarse sand)mixed

with CICOno 1@ 1.50kg per bag of cement. Normal using of the roof

should be done prior to allowing traffic This will be as per manufacturer's

application and architectural detail drawing

500.00 sqm

16.4

Providing and fixing 12mm Solid Compact laminate panel impregnated

with melamine resins bound together with thermosetting resins and cured

at a pressure 9mpa and temperature of 1500 c. as per specification

residence dry heat at 1800 rating not worse than 4,Resistence to

immersion in boiling water Mass increase 2.0% max.,Resitance to

scratching 2.0N min.Resistance to colour change rating 4 to 5, Resistance

to water vapour rating not worse than 4, Flexural strength 80 Mpa

Min.,Tensile strength 60Mpa Min.,Density 1.35g/cm3. of Greenlam

equivalent make including necessory hardware made of stainless steel

(Grade 304) (1) S.S.Gravity hinges,2) SS L drop ,3) Handle 4) Latch Lock

and 5) Screws .Door will be installed on SS Grade U chnnel.including

removal of existting old door shutter with frame. as per approved by

Engineer-incharge.

6.70 sqm

16.5Providing and fixing Odor Control System"Zerodor" Kit for Waterless urinals

10.00 Nos

Page 20 of 22


Rate (In Rupees)BOQ


16.6

Providing and fixing skylight at terrace level with Multi cell/tight cell

Polycarbonate Panel System 12mm thick of make Danpalon or GE

(minimum) confirming to specifications. Panel will be 12mm thick (min.)

single panel. The weight of the panel will be 2550 gram per square meter.

Panel Width shall not be less than 900 mm to ensure best performance for

wind uplift, vibration, oil canning and visual appearance. The panels shall

be uniform in color with an integral Tight-Cell core. Panels shall be

manufactured with Vertical Standing Seam at both sides of the panel. Snap-

on connector to interlock the panels shall have a double tooth grip-lock

locking mechanism to ensure maximum uplift capability. Panel shall be

factory sealed/end welded panels with additional End-cap/Aluminium U-

Profile (mill finish) for ends. Panels shall be co-extruded UV protected.

Panel shall be co-extruded with special anti glare compound to make it anti-

glare/soft light to prevent glare and sun streaks.

250.00 sqm

16.7

Providing and laying six courses water proofing treatment with bitumen felt

over roofs consisting of first, third and fifth courses of blown or / and

residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of

area respectively, second and fourth courses of roofing felt type 2 grade I

(fibre base self finished bitumen felt) six and final courses of stone grit 6

mm and down size or pea sized gravel spread at 6cu.dm per sqm including

preparation of surface, excluding grading, compete

100.00 sqm

16.8

Providing and laying water proofing treatment by Shalicryl -215 P on wall

including crack filling by Techoxy -3 part I &II, including applicaion of

priming coat ,applying fiber cloth ,and two coat of shalicryl complete

,including preparation of surface, stage required up to floor V level

complete .

10.00 sqm

17 Solar water heater

17.1

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE)

Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with

carbon black having thermal stability for hot & cold water supply, capable to

withstand temperature up to 80 0C, including all special fittings of

composite material (engineering plastic blend and brass inserts wherever

required) e.g. elbows, tees, reducers, couplers & connectors etc., with

clamps at 1.00 metre spacing. This includes testing of joints complete as

per direction of the Engineer in charge.

Internal work - Exposed on wall

2025 (25 mm OD) pipe 100.00 metre

Page 21 of 22


Rate (In Rupees)BOQ


17.2







clamps at 1.00 metre spacing. This includes the costs of cutting chases

and including testing of joints complete as per direction of the engineer in

charge.

Concealed work, including cutting chases and making good the wall

etc.1216 (16 mm OD) pipe 100.00 metre

17.3







trenching, refilling and testing of joints complete as per direction of the

engineer in charge.

External work

2532 (32 mm OD ) pipe 100.00 metre

3240 (40 mm OD ) pipe 100.00 metre

Total

Total Amount of work

Page 22 of 22

INDIAN INSTITUTE OF MANAGEMENT INDORE figure In words Amount (In Rupees) BOQ Rate (In Rupees) no....

Documents

Transcript of INDIAN INSTITUTE OF MANAGEMENT INDORE figure In words Amount (In Rupees) BOQ Rate (In Rupees) no....