No.SS07-23S73-0E

- 1 -

In-Circuit Emulator MN103S73

Product Name Product Number Note

ICE PX-ICE103S73

In-circuit Emulator Specification

ICE dimensional drawing

(when connected to the target)

Cable PX-CBL-PAD103S

Emulator Controller PX-PAD-103S Power supply box

Common to MN103S series.

Dummy target PRB-EX-DMY103S

73/A2/D3

Needed when debugging software with a stand-alone ICE.

(Joint screws for socket are sold separately.)

Socket joint screw MS-5

Option Probe PX-OPT-103S Common to MN103S series.

PX-IFC-PCC-6 Compliant with PCMCIA Ver2.1/JEIDA Ver4.2.

Interface

PX-IFC-PCI-6

Compliant with PCI2.1 of PCI-SIG standard.

When using the Low Profile PCI with small-footprint PC's,

replace the bracket by the provided one.

PX-SDX103S00-0P0* PanaX Series Debugger Debugger

PX-DBF103S00-0P0* DebugFactory® Builder

C Compiler/Assembler PX-ICC103S00-0P0*

MN103S73 ICE OPTION Product Name Product Number Note

396 pin PGA socket PX-ADP-MEP396S

Target

connection adapter

PX-ADP100QF18-

103-YQ-K81 Instruction

No.SS07-23S73-0E

- 2 -

PX-ICE103S73 PX-CBL-PAD103S

PX-PAD-103S PRB-EX-DMY103S73/A2/D3

MS-5 PX-OPT-103S

No.SS07-23S73-0E

- 3 -

PX-IFC-PCC-6 PX-IFC-PCI-6

PX-ADP-MEP396C PX-ADP100QF18-103-YQ-K81

1

124

28.3

9.95

26.3

43.7

29

24

29

85.4

Emulator controller( PX-PAD-103S )

Target board

20

12 12

Target board

Flexible cablesKC200-80N(n=2)

100pin-18mm : PX-ADP100QF18-103-YQ-K81

TOP

SIDE

BOTTOM

(Unit : mm)

１pin

A1

MN103S-Emulator

9.95

9.95

9.95

49.5

2923.5

135 (Reference)

Emulator controller( PX-PAD-103S )

Emulator controller( PX-PAD-103S )

S/N. 06X-31E-572A1-103S

Panasonic

PanaXseries MN103S

Adapter boardPX-ADP103S-100-81

Target socket boardEXB100SB-PA (4 screws included)

<Sold separately>Socket from TOKYO ELETECH CORPORATIONNQPACK100SB or NQPACK100SB-SL

22

27

MN103S Emulator Target conversion adapter Dimension / Connection diagrams

Replace screws (with spacers and rubber feet) included in the set.

Conversion boardPX-EX103S-128-81(4 screws included)

Software & Solutions Development CenterCorporate System LSI Development DivisionSemiconductor CompanyMatsushita Electric Industrial Co., Ltd.

Apr 14, 2008

2

Set name : PX-ADP100QF18-103-YQ-K81Supported package: QFP 100pin-18mm squareSupported product: MN103SF73R (As of October 2006)Components:1.Conversion board n=1 *

(PX-EX103S-128-81, No. PB06033A0)2.Joining screw n=4 *3.Adapter board (PX-ADP103S-100-81) n=14.80-signals flexible cable (KC200-80N) n=25.Target socket board (EXB100SB-PA) n=16.Screw for the target socket board n=4 *7.Screw (with a spacer and a rubber foot) n=4 *

MN103S Emulator Target conversion adapter Components

1.Conversion board(PX-EX103S-128-81)

2.Joining screw7.Screw (with a spacer and a rubber foot)

4.80-signals flexible cable (KC200-80N)

3.Adapter board(PX-EX103S-100-81)

5.Target socket board(EXB100SB-PA)

6.Screw for the target socket board

●This adapter requires a socket from TOKYO ELETECH CORPORATION separately.Product number:

- NQPACK100SB or NQPACK100SB-SL (Supported for 100pin-18mm square)“-SL” indicates that a long screw for fixing the target is included.

For details (size, foot pattern, etc.) of connector, refer to the website of TOKYO ELETECH CORPORATION.http://www.tetc.co.jp/e_index.htm

* : Common in the series of MN103S emulator adapter.

Software & Solutions Development CenterCorporate System LSI Development DivisionSemiconductor Company Matsushita Electric Industrial Co., Ltd.

S/N. 06X-31E-572A1-103S Apr 14, 2008

3

*1

*1*2

*2

*2*2

7. Fix the adapter board on theconversion board.

9. Connect the flexible cables withthe conversion board and the target socket board.

10. Installation has been completed.

MN103S Emulator Target conversion adapter Installation

8. Screw NQPACK (Sold separately) and the target socket board.(Note the corner cut)

*1*2

1. Replace screws on the bottom surface of the emulator housing byscrews with spacers and rubberfeet.

2. The screws have been replaced. 3. Insert the longer side of joining screws into the emulator housing.

4. Put the conversion board on the joining screws. (Make sure to join the mark ”A1”)

5-1. Tighten the rear two screws evenly.

5-2. Tighten the front two screws evenly.

Alternate5-1 and 5-2

6. The conversion board has been installed if there is no space.

Note:*1 When connecting parts, make sure to join the marks "1 pin" and "A1" respectively. *2 Special attentions should be paid to needle-points of YQPACK and the conversion board

not to bend or break them.Software & Solutions Development CenterCorporate System LSI Development DivisionSemiconductor CompanyMatsushita Electric Industrial Co., Ltd.

S/N. 06X-31E-572A1-103S Apr 14, 2008

Ex) Target board

4

MN103S Emulator Target conversion adapter Clock diagram

OSCO(12)

OSCI(13)

Emulator

MCU

OSCO

OSCI

W1

X1

Target board

W1

X1C2

C1

X2(Lead)

X1(Chip)

JP1

JP2

2 13 4OSC1

JP7

Adapterboard

JP6

JP5

JP3

JP4

C1

4 31 2OSC1

JP6JP5

JP2X2

X1C2

CN2

▼A1

X1(OSCI)

W1(OSCO)

BOTTOM VIEW

JP1

JP7

C1

4 31 2OSC1

JP6 JP5

JP2X2

X1C2

CN2

▼A1

X1(OSCI)

W1(OSCO)

BOTTOM VIEW

JP1

JP7

C1

4 31 2OSC1

JP6JP5

JP2X2

X1C2

CN2

▼A1

X1(OSCI)

W1(OSCO)

BOTTOM VIEW

JP1

JP7JP3 JP4

JP3 JP4

JP3 JP4

- Clock from the targetboard(Only OSCI)

C1

4 31 2OSC1

JP6JP5

JP2X2

X1C2

CN2

▼A1

X1(OSCI)

W1(OSCO)

BOTTOM VIEW

JP1

JP7JP3 JP4

●Circuit diagram (Example: MN103SF73R)

Flexible cable

Conversion board

Target socket board

-OSCI or OSCO from the target board is disabled.The emulator uses oscillators or resonators on the conversion board. The clock from the target board can use by short with solder.The clock from the target board supports only when input from the OSCI.

-Neither oscillator/ resonator nor condenser is included with shipment. Prepare parts as needed.

- Short JP1-JP7 with solder depending on your parts.- Recommended parts

X1 : Ceramic resonator (Chip) :Murata Manufacturing Co., Ltd. CSTCE**MOG52-R0 (** : **MHz)

X2 : Ceramic resonator (Lead) :Murata Manufacturing Co., Ltd. CSTLS**MOG53-B0 (** : **MHz)Crystal unit : Kyocera Corporation HC-49/U-S

OSC1: Clock crystal oscillator : Kyocera Corporation FXO-31FC1 : Condenser :1608 typeC2 : Condenser :1608 type

Solder

Parts(ex. Crystal unit, Condenser)

Software & Solutions Development CenterCorporate System LSI Development DivisionSemiconductor CompanyMatsushita Electric Industrial Co., Ltd.

- Ceramic resonator(Chip type, X1)

- Crystal resonator(Lead type, X2)

- Clock crystal oscillator(OSC1)

S/N. 06X-31E-572A1-103S Apr 14, 2008

5

Emulator

MCU

Target board

VDD33

3.3V

VDD18

1.8V

C6

R

VSS

C7 C9

C4C3

C8

C5

VDIO

VDINT

VSS

・・

・・

・・

・・

・・

JP1 JP2

X1

BOTTOM VIEW

VDD33

VSS

+

4 3

1 2OSC1

・・・・・・

・・・・・・

X2

C3

C4

・・

・・

・・

・・

・・

+C7 C6

C9C8

+C5

+

CN1 CN2

VDIO VSS VDINT

VDIOVSSVDINT

A

C

E

G

J

B

D

F

H

A1

R

MN103S Emulator Target conversion adapter Power supply / GND diagrams

VDD5

5VVDIO2

9 7 5 3 1

Emulator1.8V

C1 C2

JP4JP3

JP7JP6

JP5

OFF

- Short VDD33 and VSS on the conversion board and those on the target with short thick wires respectively.

- No condenser is included with shipment. Prepare parts as needed.- Feature of condenser

3.5mm x 2.8mm : C4, C5, C7, C91608 type : C3, C6, C8 (C1, C2)

Software & Solutions Development CenterCorporate System LSI Development DivisionSemiconductor CompanyMatsushita Electric Industrial Co., Ltd.

To target VDD33To target GND

To target VDD33

To target GND

● Parts allocation on the conversion board(PX-EX103S-128-81)

● Circuit diagram (Example: MN103SF73R)

Conversion board

Adapterboard

Flexible cable Target socket

board

Short(wire)

Short(wire) Test pin

(red)

Test pin(black)

Test pin(yellow)

VSS for Emulator

USR pin = 100 pins

: Regulator

VDD5

VDD18

S/N. 06X-31E-572A1-103S Apr 14, 2008