Improvement of Call completion ration in CDoT Xge
description
Transcript of Improvement of Call completion ration in CDoT Xge
H:\MAX\LECTURE\CCRIMPROVEMENT 1C-DOT Proprietary
www.cdot.com
CCR IMPROVEMENT IN CCR IMPROVEMENT IN CCR IMPROVEMENT IN CCR IMPROVEMENT IN CCCC----DOT EXCHANGEDOT EXCHANGEDOT EXCHANGEDOT EXCHANGE
H:\MAX\LECTURE\CCRIMPROVEMENT 2C-DOT Proprietary
www.cdot.com
CCR – CALL COMPLETION RATIO
CSR – CALL SUCCESS RATIO
Certain TerminologiesCertain TerminologiesCertain TerminologiesCertain Terminologies
H:\MAX\LECTURE\CCRIMPROVEMENT 3C-DOT Proprietary
www.cdot.com
CATEGORY OF CALLSCATEGORY OF CALLSCATEGORY OF CALLSCATEGORY OF CALLSOriginating & Terminating Call (ORGOriginating & Terminating Call (ORG--TRM)TRM)
All Local Call (Intra BM + Inter BM + AN-RAX + WLL)
Total Local Call Attempts (i.e. Dial Tone Given)Total Successful Call Attempts (i.e. Call Processed)Total Completed Call Attempts (i.e. Answer Calls)
H:\MAX\LECTURE\CCRIMPROVEMENT 4C-DOT Proprietary
www.cdot.com
CATEGORY OF CALLSCATEGORY OF CALLSCATEGORY OF CALLSCATEGORY OF CALLSOriginating & Outgoing Call (ORGOriginating & Outgoing Call (ORG--OG)OG)
All Route Call & MultiOperator CallsTotal Outgoing Call Attempts (i.e. Dial Tone Given)Total Successful OG Call Attempts (i.e. Call Processed / State of Call received)Total Completed Call Attempts (i.e. Answer Signal Received)
Terminating Call (IC-TRM)All Local/Route Terminating Calls
Total Terminating Call AttemptsTotal Completed Terminating Attempts (i.e. Answered Calls)
H:\MAX\LECTURE\CCRIMPROVEMENT 5C-DOT Proprietary
www.cdot.com
CALL FAILURE ANALYSISCALL FAILURE ANALYSISCALL FAILURE ANALYSISCALL FAILURE ANALYSISAbandoned After Dialing CompleteAbandoned After Dialing Complete.
ØDue to Subscriber’s Behavior.ØDue to More Nodes in Network.
No AnswerNo Answer.ØDue to Subscriber’s Reason.ØDue to Seasonal/Climatic Cause.ØDue to Technical Reasons.
Called Subscriber BusyCalled Subscriber Busy.ØHeavy Callers/Hospitals/Helpline Nos.
Partial DialingPartial Dialing.ØDue to Subscriber’s Behavior
No Digits DialedNo Digits Dialed. (This Contribute 25% failure)ØDue to Subscriber’s Behaviour (Check Dial Tone /
Flashing Hook before Dialing)
H:\MAX\LECTURE\CCRIMPROVEMENT 6C-DOT Proprietary
www.cdot.com
INTERNAL REASONSINTERNAL REASONSINTERNAL REASONSINTERNAL REASONS
Scope of Improving CCR.Scope of Improving CCR.
Feed the Dial Tone in Time.Feed Proper Announcement.Check the various Call Processing Parameters.Check the Resource Allocation.Provide Adequate Trunk Circuits.Routine Testing of CM & BM Hardware.Data Check to Avoid No-answer.
H:\MAX\LECTURE\CCRIMPROVEMENT 7C-DOT Proprietary
www.cdot.com
SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) REASONREASONREASONREASON
Dial Tone Delay & NoDial Tone Delay & No--Dial Tone.Dial Tone.All subs. Should be of DTMF(PSTN+AN) and instrument should be modified for Tone Working.All Line BM,RBM & VU-BM should be equipped 4MFC cards and all ports are configured as DTMF.Routine testing of MFC cards using tst-srv:301 using calendar.
Feed Proper Announcement at Appropriate Time.Feed Proper Announcement at Appropriate Time.Announcement card should be equipped & inservice in all BMs.Proper OG-barring, Feature Invocation announcement.Q-annc in case of busy subs. if assigned “calledcalled--callcall--waitingwaiting”. Do wide publicity to popularize call-waiting facilities.
H:\MAX\LECTURE\CCRIMPROVEMENT 8C-DOT Proprietary
www.cdot.com
SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) REASONREASONREASONREASON (CONTD.)(CONTD.)(CONTD.)(CONTD.)
Check Call Processing.Check Call Processing.For effective call check the following System Parameters.
ROUTING: Minimum digits required for processing route call in open-number scheme. It should be 6.MIN-SUBS-DIAL: Minimum digits required for processing local call.DNA-TMR: This parameter is effective for Diversion on No-Reply. It should be 280.
Resource Allocation.Resource Allocation.In Line BM/RBM/VU-BM all 4MFCs should be created as DTMF.In Trunk BM equip all 4 MFCs as MF-SENDR/MF-RCVR for MOD-R2 Calls.
H:\MAX\LECTURE\CCRIMPROVEMENT 9C-DOT Proprietary
www.cdot.com
SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) REASONREASONREASONREASON (CONTD.)(CONTD.)(CONTD.)(CONTD.)
Providing Adequate Trunk Circuits.Providing Adequate Trunk Circuits.Sufficient junction should be provided towards TAX/Parent Exchg. as the call should not fail due to Non-availability of Trunks.For the improvement of ORG-OG traffic efficiency, test DTS/DTCs on routine basis.TUC should be interchanged & Tested regularly.Other than 2_2_(7.7)_6 s/w rel., 21st slot/4th TU should not be equipped.
H:\MAX\LECTURE\CCRIMPROVEMENT 10C-DOT Proprietary
www.cdot.com
SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) SOLUTION TO SWITCH(INTERNAL) REASONREASONREASONREASON (CONTD.)(CONTD.)(CONTD.)(CONTD.)
Check of CM & BM Hardware.Check of CM & BM Hardware.Routine Testing CM Hardware (BUS Wise & Plane Wise) to avoid one way speech and cross-talk related problem.Testing of TIC/SPC cards on routine basis using the cmdfile.
Data Check for Avoiding NoData Check for Avoiding No--Answer Case.Answer Case.Check System Parameters to reduce NoCheck System Parameters to reduce No--Answer Case.Answer Case.
For Exchange Type :2(Working as Local For Exchange Type :2(Working as Local ExchgExchg.).)
CSH:600CL-RINGING:600
For Exchange Type :4(Working as TAX/ILT)For Exchange Type :4(Working as TAX/ILT)
RING-TAX-TM-OUT:600CSH-TAX-TM-OUT:300
H:\MAX\LECTURE\CCRIMPROVEMENT 11C-DOT Proprietary
www.cdot.com
Threshold ParametersThreshold ParametersThreshold ParametersThreshold Parameters
Threshold % should be Calculated for CCS#7 and V5.2 based on the number of :
FOR CCS#7 DATA (Applicable to Complete System)ØNo. of DATA Links (NO7-THR).ØNo. of BMs having #7 TGPs (INT-THR).
FOR VUBM DATA (Applicable per VU BM basis)ØNo. of Terminal for Internal Comm. (VU-INT-THR)ØNo. of Links for VU Interface (V5-THR)
H:\MAX\LECTURE\CCRIMPROVEMENT 12C-DOT Proprietary
www.cdot.com
Different Numbering SchemeDifferent Numbering SchemeDifferent Numbering SchemeDifferent Numbering Scheme
OPEN Numbering SchemeØ The open numbering scheme is followed in the stages
of the network where the exchange either routes the call to a TANDEM/TAX and not aware of the details of numbering scheme/number length of the destination.
CLOSE Numbering SchemeØ The closed numbering scheme is followed in the
stages of the network where the exchange either terminates the call or routes the call directly to a terminating exchange and is aware of the details of numbering scheme/number length of the destination.
H:\MAX\LECTURE\CCRIMPROVEMENT 13C-DOT Proprietary
www.cdot.com
SIGNALLINGSIGNALLINGSIGNALLINGSIGNALLING
H:\MAX\LECTURE\CCRIMPROVEMENT 14C-DOT Proprietary
www.cdot.com
Originating Exch.
Originating Exch.
Terminating Exch.
Terminating Exch.
Transit Exch.
Transit Exch.
END-TO-ENDEND-TO-END
ENDENDENDEND----TOTOTOTO----ENDENDENDEND
In End-to-End mode, Signaling is between Originating Exchange and Terminating Exchange thus signals can be transferred very quickly.
H:\MAX\LECTURE\CCRIMPROVEMENT 15C-DOT Proprietary
www.cdot.com
Originating Exch.
Originating Exch.
Terminating Exch.
Terminating Exch.
Transit Exch.
Transit Exch.
LINK BY LINKLINK BY LINK
LINK BY LINKLINK BY LINKLINK BY LINKLINK BY LINK
In Link-by-Link mode, Signal is between Two Nodes only thus slowing down the Transfer of the Signal.
LINK BY LINKLINK BY LINK
H:\MAX\LECTURE\CCRIMPROVEMENT 16C-DOT Proprietary
www.cdot.com
TYPE OF TYPE OF TYPE OF TYPE OF TAXsTAXsTAXsTAXs
Leading TAXLeading TAXØ First TAX in the Network has to Function as a Leading
TAX.
Transit TAXTransit TAXØ This is doing only Transiting Function and no TAX
business. It passes all the digits.
Terminating TAXTerminating TAXØAbsorbs Area Code and sends exchange digits to the
Terminating Exchange using appropriate Rank Of Digit.
H:\MAX\LECTURE\CCRIMPROVEMENT 17C-DOT Proprietary
www.cdot.com
ORG Exch.ORG Exch.
Terminating TAX
Terminating TAX
Leading TAX
Leading TAX
LINK BY LINKLINK BY LINK
TYPES OF TAXTYPES OF TAXTYPES OF TAXTYPES OF TAXEND-TO-ENDEND-TO-END
TransitTAX
TransitTAX
TRMExch.TRMExch.OG TGP-
TYP=TTAXOG TGP-
TYP=TTAX
IC TGP-TYP=ORDIC TGP-
TYP=ORD
OG TGP-TYP=TTAXOG TGP-
TYP=TTAX
IC TGP-TYP=TTAX
IC TGP-TYP=TTAX
OG TGP-TYP=TTAXOG TGP-
TYP=TTAX
IC TGP-TYP=TTAX
IC TGP-TYP=TTAX
OG TGP-TYP=ORDOG TGP-
TYP=ORD
IC TGP-TYP=TTAX
IC TGP-TYP=TTAX
H:\MAX\LECTURE\CCRIMPROVEMENT 18C-DOT Proprietary
www.cdot.com
PROGRAMING OF PROGRAMING OF PROGRAMING OF PROGRAMING OF TGPsTGPsTGPsTGPs
ALL THE I/C TRK GROUPS FROM TAX OR ILT SHOULD BE PROGRAMMED AS TTAX WITH THE UNIQUE 'TGP-CAT' OTHER THAN '1' AND NOT ALLOCATED TO ANY OTHER TGP.
ALL THE I/C TGPs FROM THE PARENTED EXCHANGES (IN TAX) SHOULD BE DEFINED AS 'ORD'.
PROPER CHARGE RATE NUMBER FOR I/C CALLS FROM OTHER TAXs FOR WHICH OUR TAX IS NOT A LEADING TAXØ CRG-RTN (=4) WITH
CHARGE MODE = NO-METMETERING INFO = METERED/ANS-XP/NRM-RNG
Ø NO CHARGE BAND SHOULD BE ASSOCIATED WITH THIS CRG-RTN
H:\MAX\LECTURE\CCRIMPROVEMENT 19C-DOT Proprietary
www.cdot.com
SUBS. PRIORITYSUBS. PRIORITYSUBS. PRIORITYSUBS. PRIORITYSubscriber Priority (SUBSubscriber Priority (SUB--PRI)PRI)
This Parameter is used for assigning preference to Subscriber LINES.ØPriority 1 to 8 assigned by CRP CommandØPriority 9 to 14 assigned by the system
Spare11,14
Operator13
PBX12
CCB-STD10
ORD-CCB9
Priority Subscriber2,3,4,5,6
Ordinary Subscriber1,7,8
MeaningSUB-PRI at LE
H:\MAX\LECTURE\CCRIMPROVEMENT 20C-DOT Proprietary
www.cdot.com
In MFIn MF--R2 R2 SignallingSignallingSubs Priority 2 to 6 is send as Priority Subs.In Terminating Exchange if Priority 2 is not allowed in TGP-Choice field then call will fail.If Priority 13 is not allowed TO calls from the Network will fail.In case of Subs Priority 9,10&12 Local Incoming TGP-PRI data takes precedence at Transit Exch.
PRIORITY ROUTINGPRIORITY ROUTINGPRIORITY ROUTINGPRIORITY ROUTING
H:\MAX\LECTURE\CCRIMPROVEMENT 21C-DOT Proprietary
www.cdot.com
PRIORITY ROUTINGPRIORITY ROUTINGPRIORITY ROUTINGPRIORITY ROUTINGIn CCS#7 In CCS#7 SignallingSignalling
Except Trunk Operator & Ordinary Except Trunk Operator & Ordinary Calling Subs, all other Priority Subs in Calling Subs, all other Priority Subs in the Transit Network Selection are the Transit Network Selection are Treated as Priority=1 for the purpose of Treated as Priority=1 for the purpose of Outgoing Trunk Selection irrespective Outgoing Trunk Selection irrespective
of Incoming TGP Priority.of Incoming TGP Priority.
H:\MAX\LECTURE\CCRIMPROVEMENT 22C-DOT Proprietary
www.cdot.com
SUGGESTIONSUGGESTIONSUGGESTIONSUGGESTION
Always create Two or Three smaller size TGPs with TENs from Two/Three BMs. TGP choice in rotating order for different route codes and for different priorities.
(Advantage: Processor Load & Trunk Selection Time will Decrease considerably)
For Non-Metered Special Service routes, Non-Metered type CRG-RTN should be given instead of PRD-TAX.End-to-End MF Signalling can be adopted, wherever possible.Use proper TGP-TYPE and EXCH-TYPE.