IM708 INVERTEC V350-PRO (CE) January, 2001€¦ · ipisc i ng li, e d am n eli d a m non m umm y bh...

INVERTEC V350-PRO (CE)

OPERATOR’S MANUAL

For use with machines Code; 10670

IM708January, 2001

Safety Depends on YouLincoln arc welding and cuttingequipment is designed and builtwith safety in mind. However, youroverall safety can be increased byproper installation ... and thought-ful operation on your part. DONOT INSTALL, OPERATE ORREPAIR THIS EQUIPMENTWITHOUT READING THISMANUAL AND THE SAFETYPRECAUTIONS CONTAINEDTHROUGHOUT. And, mostimportantly, think before you actand be careful.

™

WARNING

REMOTE

POWER

OFF

ON

A AMPS

A

V VOLTS

WELD TERMINALS

SELECT

OUTPUTLINCOLNELECTRIC

INVERTEC V350-PRO

WARNINGWARNING

AVISO DE

PRECAUCION

ATTENTION

!

!

!

!

Lorem ipsum dolor sit amet consectetuer adipiscing


elit, ed diam non

elit, ed diam nonummummy nibh euismod tincidunt ut

y nibh euismod tincidunt ut

laoreet dolore magna aliquam er

laoreet dolore magna aliquam eratat



elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non





Date of Purchase:Serial Number:Code Number:Model:Where Purchased:

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

IEC 974-1IP21S

Copyright © 2001 Lincoln Global Inc.

ISO 9001

CERTIFICATE NUMBER: 30273

Designed and Manufactured Under aQuality Program Certified byABS Quality Evaluations, Inc.to ISO 9001 Requirements.

QMSANSI RAB

FOR ENGINEpowered equipment.

1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.

____________________________________________________1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes outdoors.

____________________________________________________1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.Stop the engine and allow it to cool beforerefueling to prevent spilled fuel from vaporiz-ing on contact with hot engine parts andigniting. Do not spill fuel when filling tank. Iffuel is spilled, wipe it up and do not startengine until fumes have been eliminated.

____________________________________________________1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing andtools away from V-belts, gears, fans and all other movingparts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safetyguards to perform required maintenance. Removeguards only when necessary and replace them when themaintenance requiring their removal is complete.Always use the greatest care when working near movingparts.

___________________________________________________1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor oridler by pushing on the throttle control rodswhile the engine is running.

___________________________________________________1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenancework, disconnect the spark plug wires, distributor cap ormagneto wire as appropriate.

iSAFETYi

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that youpurchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is availablefrom the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES AREPERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

Mar ‘95

ELECTRIC AND MAGNETIC FIELDSmay be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, andwelders having a pacemaker should consult their physicianbefore welding.

2.c. Exposure to EMF fields in welding may have other healtheffects which are now not known.

2.d. All welders should use the following procedures in order tominimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Securethem with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode andwork cables. If the electrode cable is on your right side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close aspossible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove theradiator pressure cap when the engine ishot.

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituentsare known to the State of California to cause can-cer, birth defects, and other reproductive harm.

The engine exhaust from this product containschemicals known to the State of California to causecancer, birth defects, or other reproductive harm.

The Above For Diesel Engines The Above For Gasoline Engines

iiSAFETYii

ARC RAYS can burn.4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks andthe rays of the arc when welding or observingopen arc welding. Headshield and filter lensshould conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistantmaterial to protect your skin and that of your helpers fromthe arc rays.

4.c. Protect other nearby personnel with suitable, non-flammablescreening and/or warn them not to watch the arc nor exposethemselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK cankill.3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.Do not touch these “hot” parts with your bareskin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.Make certain the insulation is large enough to cover your fullarea of physical contact with work and ground.

In addition to the normal safety precautions, if weldingmust be performed under electrically hazardousconditions (in damp locations or while wearing wetclothing; on metal structures such as floors, gratings orscaffolds; when in cramped positions such as sitting,kneeling or lying, if there is a high risk of unavoidable oraccidental contact with the workpiece or ground) usethe following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.• DC Manual (Stick) Welder.• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,electrode reel, welding head, nozzle or semiautomaticwelding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electricalconnection with the metal being welded. The connectionshould be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical(earth) ground.

3.f. Maintain the electrode holder, work clamp, welding cable andwelding machine in good, safe operating condition. Replacedamaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts ofelectrode holders connected to two welders because voltagebetween the two can be the total of the open circuit voltageof both welders.

3.i. When working above floor level, use a safety belt to protectyourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

FUMES AND GASEScan be dangerous.5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing thesefumes and gases.When welding, keepyour head out of the fume. Use enoughventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. Whenwelding with electrodes which require specialventilation such as stainless or hard facing (seeinstructions on container or MSDS) or on lead orcadmium plated steel and other metals or coatingswhich produce highly toxic fumes, keep exposure aslow as possible and below Threshold Limit Values (TLV)using local exhaust or mechanical ventilation. Inconfined spaces or in some circumstances, outdoors, arespirator may be required. Additional precautions arealso required when welding on galvanized steel.

5.b. Do not weld in locations near chlorinated hydrocarbon vaporscoming from degreasing, cleaning or spraying operations.The heat and rays of the arc can react with solvent vapors toform phosgene, a highly toxic gas, and other irritating prod-ucts.

5.c. Shielding gases used for arc welding can displace air andcause injury or death. Always use enough ventilation,especially in confined areas, to insure breathing air is safe.

5.d. Read and understand the manufacturer’s instructions for thisequipment and the consumables to be used, including thematerial safety data sheet (MSDS) and follow youremployer’s safety practices. MSDS forms are available fromyour welding distributor or from the manufacturer.

5.e. Also see item 1.b.

Mar ‘95

FOR ELECTRICALLYpowered equipment.

8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.

8.b. Install equipment in accordance with the U.S. NationalElectrical Code, all local codes and the manufacturer’srecommendations.

8.c. Ground the equipment in accordance with the U.S. NationalElectrical Code and the manufacturer’s recommendations.

CYLINDER may explodeif damaged.7.a. Use only compressed gas cylinders

containing the correct shielding gas for theprocess used and properly operatingregulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable forthe application and maintained in good condition.

7.b. Always keep cylinders in an upright position securelychained to an undercarriage or fixed support.

7.c. Cylinders should be located:•Away from areas where they may be struck or subjected tophysical damage.

•A safe distance from arc welding or cutting operations andany other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any otherelectrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outletwhen opening the cylinder valve.

7.f. Valve protection caps should always be in place and handtight except when the cylinder is in use or connected foruse.

7.g. Read and follow the instructions on compressed gascylinders, associated equipment, and CGA publication P-l,“Precautions for Safe Handling of Compressed Gases inCylinders,” available from the Compressed Gas Association1235 Jefferson Davis Highway, Arlington, VA 22202.

iiiSAFETYiii

Mar ‘95

WELDING SPARKS cancause fire or explosion.6.a. Remove fire hazards from the welding area.

If this is not possible, cover them to preventthe welding sparks from starting a fire.Remember that welding sparks and hot

materials from welding can easily go through small cracksand openings to adjacent areas. Avoid welding nearhydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,special precautions should be used to prevent hazardoussituations. Refer to “Safety in Welding and Cutting” (ANSIStandard Z49.1) and the operating information for theequipment being used.

6.c. When not welding, make certain no part of the electrodecircuit is touching the work or ground. Accidental contactcan cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until theproper steps have been taken to insure that such procedureswill not cause flammable or toxic vapors from substancesinside. They can cause an explosion even though they havebeen “cleaned”. For information, purchase “RecommendedSafe Practices for the Preparation for Welding and Cutting ofContainers and Piping That Have Held HazardousSubstances”, AWS F4.1 from the American Welding Society(see address above).

6.e. Vent hollow castings or containers before heating, cutting orwelding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oilfree protective garments such as leather gloves, heavy shirt,cuffless trousers, high shoes and a cap over your hair. Wearear plugs when welding out of position or in confined places.Always wear safety glasses with side shields when in awelding area.

6.g. Connect the work cable to the work as close to the weldingarea as practical. Work cables connected to the buildingframework or other locations away from the welding areaincrease the possibility of the welding current passingthrough lifting chains, crane cables or other alternate cir-cuits. This can create fire hazards or overheat lifting chainsor cables until they fail.

6.h. Also see item 1.c.

ivSAFETYiv

PRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques qui parraissent dans cemanuel aussi bien que les précautions de sûreté générales suiv-antes:

Sûreté Pour Soudage A L’Arc1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tensionquand la machine à souder est en marche. Eviter toujourstout contact entre les parties sous tension et la peau nueou les vétements mouillés. Porter des gants secs et sanstrous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand onsoude dans des endroits humides, ou sur un planchermetallique ou des grilles metalliques, principalement dans les positions assis ou couché pour lesquelles une grandepartie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câblede soudage et la machine à souder en bon et sûr étatdefonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour lerefroidir.

e. Ne jamais toucher simultanément les parties sous tensiondes porte-électrodes connectés à deux machines à souderparce que la tension entre les deux pinces peut être letotal de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source decourant pour soudage semi-automatique, ces precautionspour le porte-électrode s’applicuent aussi au pistolet desoudage.

2. Dans le cas de travail au dessus du niveau du sol, se protégercontre les chutes dans le cas ou on recoit un choc. Ne jamaisenrouler le câble-électrode autour de n’importe quelle partiedu corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,donc:

a. Utiliser un bon masque avec un verre filtrant appropriéainsi qu’un verre blanc afin de se protéger les yeux du ray-onnement de l’arc et des projections quand on soude ouquand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger lapeau de soudeur et des aides contre le rayonnement del‘arc.

c. Protéger l’autre personnel travaillant à proximité ausoudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc desoudage. Se protéger avec des vêtements de protection libresde l’huile, tels que les gants en cuir, chemise épaisse, pan-talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone desoudage. Utiliser des lunettes avec écrans lateraux dans les

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin deprévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé dela masse. Un court-circuit accidental peut provoquer unéchauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possiblede la zone de travail qu’il est pratique de le faire. Si on placela masse sur la charpente de la construction ou d’autresendroits éloignés de la zone de travail, on augmente le risquede voir passer le courant de soudage par les chaines de lev-age, câbles de grue, ou autres circuits. Cela peut provoquerdes risques d’incendie ou d’echauffement des chaines et descâbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.Ceci est particuliérement important pour le soudage de tôlesgalvanisées plombées, ou cadmiées ou tout autre métal quiproduit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenantd’opérations de dégraissage, nettoyage ou pistolage. Lachaleur ou les rayons de l’arc peuvent réagir avec les vapeursdu solvant pour produire du phosgéne (gas fortement toxique)ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,voir le code “Code for safety in welding and cutting” CSAStandard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POURLES MACHINES À SOUDER ÀTRANSFORMATEUR ET ÀREDRESSEUR

1. Relier à la terre le chassis du poste conformement au code del’électricité et aux recommendations du fabricant. Le dispositifde montage ou la piece à souder doit être branché à unebonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seronteffectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch-er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leurplace.

Mar. ‘93

vSAFETYv

V350-PRO (CE)

L10093

3-1-96H

Conformance

standard: EN 50 199 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It

All electrical equipment generates small amounts of electromagnetic emission. Electrical emission may be

received by other equipment, electrical interference may result. Electrical emissions may affect many kinds of

telephone systems, computers, etc. Be aware that interference may result and extra precautions may be required

If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment

to resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may

electromagnetic disturbances must be reduced to the point where they are no longer troublesome.

assess whether the changes will increase the risk of injury, e.g., by allowing parallel welding

surrounding area. The following shall be taken into account:

welding equipment;

b) radio and television transmitters and receivers;

d) safety critical equipment, e.g., guarding of industrial equipment;

e) the health of the people around, e.g., the use of pacemakers and hearing aids;

f) equipment used for calibration or measurement;

used in the environment is compatible. This may require additional protection measures;

ELECTROMAGNETIC COMPATIBILITY (EMC)

Products displaying the CE mark are in conformity with European Community Council Directive of 3 May

1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility

(89/336/EEC). It was manufactured in conformity with a national standard that implements a harmonized

is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.

Introduction

transmitted through power lines or radiated through space, similar to a radio transmitter. When emissions are

electrical equipment; other nearby welding equipment, radio and TV reception, numerical controlled machines,

when a welding power source is used in a domestic establishment.

Installation and Use

The user is responsible for installing and using the welding equipment according to the manufacturer s instructions.

be as simple as earthing (grounding) the welding circuit, see Note. In other cases it could involve constructing an

electromagnetic screen enclosing the power source and the work complete with associated input filters. In all cases

Note: The welding circuit may or may not be earthed for safety reasons according to national codes.

Changing the earthing arrangements should only be authorized by a person who is competent to

current return paths which may damage the earth circuits of other equipment.

Assessment of Area

Before installing welding equipment the user shall make an assessment of potential electromagnetic problems in the

a) other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the

c) computer and other control equipment;

g) the immunity of other equipment in the environment. The user shall ensure that other equipment being

h) the time of day that welding or other activities are to be carried out.

viSAFETYvi

V350-PRO (CE)

The size of the surrounding area to be considered will depend on the structure of the building and other

Methods of Reducing Emissions

Consideration should be given to shielding the supply cable of permanently installed welding equipment

conduit or equivalent. Shielding should be electrically continuous throughout its length. The shielding s

connected to the welding power source so that good electrical contact is maintained between the condu

welding power source enclosure.

access and service doors and covers should be closed and properly fastened when the welding equipm

be adjusted and maintained according to the manufacturer s recommendations.

The welding cables should be kept as short as possible and should be positioned close together, runnin

to the floor level.

Equipotential Bonding

touching these metallic components and the electrode at the same time. The operator should be insula

Earthing of the Workpiece

of injury to users, or damage to other electrical equipment. Where necessary, the connection of the wor

Screening and Shielding

Selective screening and shielding of other cables and equipment in the surrounding area may alleviate p

interference. Screening of the entire welding installation may be considered for special applications.

Portions of the preceding text are contained in EN50199: "Electromagnetic Compatibility (EMC) proarc welding equipment."

1

1

ELECTROMAGNETIC COMPATIBILITY (EMC)

that are taking place. The surrounding area may extend beyond the boundaries of the premises.

Mains Supply

Welding equipment should be connected to the mains supply according to the manufacturer s recomme

If interference occurs, it may be necessary to take additional precautions such as filtering of the mains s

Maintenance of the Welding Equipment

The welding equipment should be routinely maintained according to the manufacturer s recommendatio

operation. The welding equipment should not be modified in any way except for those changes and adj

covered in the manufacturers instructions. In particular, the spark gaps of arc striking and stabilizing de

Welding Cables

Bonding of all metallic components in the welding installation and adjacent to it should be considered. H

metallic components bonded to the work piece will increase the risk that the operator could receive a sh

such bonded metallic components.

Where the workpiece is not bonded to earth for electrical safety, not connected to earth because of its s

position, e.g., ships hull or building steelwork, a connection bonding the workpiece to earth may reduce

in some, but not all instances. Care should be taken to prevent the earthing of the workpiece increasing

earth should be made by a direct connection to the workpiece, but in some countries where direct conn

permitted, the bonding should be achieved by suitable capacitance, selected according to national regu

Thank You for selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much pride as we have in bringing this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep ithandy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.The level of seriousness to be applied to each is explained below:

WARNINGThis statement appears where the information must be followed exactly to avoid serious personal injury orloss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage tothis equipment.

CAUTION

Please Examine Carton and Equipment For Damage ImmediatelyWhen this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claimsfor material damaged in shipment must be made by the purchaser against the transportation company at thetime the shipment is received.

Please record your equipment identification information below for future reference. This information can befound on your machine nameplate.

Model Name & Number _____________________________________

Code & Serial Number _____________________________________

Date of Purchase _____________________________________

Whenever you request replacement parts for or information on this equipment always supply the informationyou have recorded above.

viivii

viiiviii TABLE OF CONTENTSPage

Installation .......................................................................................................Section ATechnical Specifications ........................................................................................A-1

Safety Precautions ..........................................................................................A-2Select Suitable Location..................................................................................A-2Stacking ..........................................................................................................A-2Tilting...............................................................................................................A-2 Input and Grounding Connections ..................................................................A-2Power Cord Connection ..................................................................................A-2Connection of Wire Feeders to V350-PRO (CE).............................................A-2Remote Control of Invertec .............................................................................A-3Undercarriage Mountings................................................................................A-3Parallel Operations..........................................................................................A-4Ouick Disconnect Plugs ..................................................................................A-4

Operation .........................................................................................................Section BAdditional Safety Precautions ...............................................................................B-1General Description and Duty Cycle......................................................................B-1Operational Features and Controls.........................................................B-1 Thru B-3Remote Control of the Output Control and Weld Terminals ..................................B-3Design Features and Advantages .........................................................................B-4Auxiliary Power ......................................................................................................B-5Limitations..............................................................................................................B-5Recommended Processes ....................................................................................B-5

Accessories .....................................................................................................Section CGeneral Options / Accessories ..............................................................................C-1“CE” Version ........................................................................................................................C-1Field Installed Options/Accessories.......................................................................C-1

Maintenance ....................................................................................................Section DSafety Precautions ................................................................................................D-1CAPACITOR DISCHARGE PROCEDURE..........................................................................D-1VISUAL INSPECTION...................................................................................................D-1ROUTINE MAINTENANCE ............................................................................................D-1PERIODIC MAINTENANCE ...........................................................................................D-1

Section E ..............................................................................................TroubleshootingSafety Precautions.................................................................................................E-1How to Use Troubleshooting Guide.......................................................................E-1Troubleshooting Guide ...........................................................................E-2 Thru E-3Fault Codes ...........................................................................................................E-4Displays .................................................................................................................E-5

Connection , Wiring Diagrams and Dimension Prints .................................Section F

Parts List ......................................................................................................P389 Series

V350-PRO (CE)

A-1INSTALLATION A-1

TECHNICAL SPECIFICATIONS - INVERTEC V350-PRO (CE)INPUT AC VOLTAGE & DC OUTPUT

OUTPUT CABLES, CONNECTIONS AND LIMITATIONS

Product Ordering Input AC Rated DC Output Output Weight DimensionsName Information Voltage Amps/Volts/Duty Cycle Range with Cord HxWxD

50/60 Hz (continuous)

350A / 34V / 60% 14.7”x12.5”xInvertec 200-220/ 3 Phase 27.8”* V350- K1728-3 380-400/ 320A / 33V / 60% AMPS 82.5lbs (373x318xPRO “CE” 415-440/ 1 Phase 5-425 (37.4 kg) 706*)mm

60/50 Hz275A / 31V /100%

1 & 3 Phase * Includeshandles

* Overall Length Including Handle, 27.8” (706mm) without handle.

Select the output cable size based upon the following chart.Cable sizes for Combined Length of Electrode and Work Cable (Copper) 75C rated:

DUTY CYCLE CURRENT LENGTH UP 61m (200 FT) 61-76m (200-250 FT)100% 275 1/0 1/060% 350 1/0 2/0

V350-PRO (CE) INPUT CURRENT (CE)

2. When operating on these inputs, the line cord should be changed to an input conductor of 6 AWG or larger.1. Not rated is indicated by 4-x's in the box on the rating plate

Recommended Fuse Sizes Based On The U.S. National Electrical Code And Maximum Machine OutputsInput 50/60 Hz Output RecommendedVoltage Phases 275Amps@ 350Amps@ Line Cord Size Fuse Size Notes

31Volts(100%) 34Volts(60%) AWG[IEC] SIZES200 3 35 48 6 80A Note 2220 3 35 48 6 80A Note 2380 3 21 28 8 50A400 3 20 27 8 50A415 3 19 26 8 50A440 3 18 24 8 50A

Voltage Phases 275Amps@ 320Amps@ Line Cord Size Fuse Size Notes31Volts(100%) 33Volts(60%)

200 1 ---- ---- --- ----- Note 1220 1 64 82 4 125A Note 2380 1 44 55 6 80A Note 2400 1 40 50 8 80A415 1 38 48 8 80A440 1 35 45 8 80A

A-2INSTALLATION A-2

SELECT SUITABLE LOCATIONThe Invertec V350-PRO (CE) will operate in harshenvironments. Even so, it is important that simple pre-ventative measures are followed in order to assurelong life and reliable operation.

• The machine must be located where there is free cir-culation of clean air such that air movement in theback, out the sides and bottom will not be restricted.

• Dirt and dust that can be drawn into the machineshould be kept to a minimum. Failure to observethese precautions can result in excessive operatingtemperatures and nuisance shutdown.

• Keep machine dry. Shelter from rain and snow. Donot place on wet ground or in puddles.

STACKINGV350-PRO (CE) cannot be stacked.

TILTINGPlace the machine directly on a secure, level surfaceor on a recommended undercarriage. The machinemay topple over if this procedure is not followed.

INPUT AND GROUNDING CONNECTIONS• Only a qualified electrician should connect the

Invertec V350-PRO (CE). Installation should bemade in accordance with the appropriate NationalElectrical Code, all local codes and the informationdetailed below.

• When received directly from the factory, multiplevoltage machines are internally connected for440VAC. If 440VAC is the desired input, then themachine may be connected to the power systemwithout any setup required inside the machine.

• Initial 200VAC - 415VAC operation will require anInput voltage panel setup.• Open the access panel on the rear of the machine.• For 200 or 230: Position the large switch to 200-230.

For higher voltages: Position the large switch to ≥ 380.• Move the "A" lead to the appropriate terminal.

POWER CORD CONNECTIONA 5 meter power cord is wired into the machine.Follow the power cord connection instructions.Incorrect connection may result in equipment damage.

SAFETY PRECAUTIONS

ELECTRIC SHOCK can kill.

• TURN THE INPUT POWER OFF AT THE DISCONNECT SWITCH BEFOREATTEMPTING TO CONNECT OR DIS-

CONNECT INPUT POWER LINES, OUTPUTCABLES, OR CONTROL CABLES.

• Only qualified personnel should perform thisinstallation.

• Connect the green/yellow lead of the powercord to ground per appropriate NationalElectrical Code.

----------------------------------------------------------------------

WARNING

Single Phase InputConnect green/yellow lead to ground per NationalElectrical Code.Connect blue and brown leads to power.Wrap black lead with tape to provide 600V insulation.Three Phase InputConnect green/yellow lead to ground per appropriateNational Electric Code.Connect blue, black and brown leads to power.

CONNECTIONS OF WIRE FEEDERS TO V350-PRO (CE)LN-25 Connection Instructions• Turn the Invertec power switch "off".• Connect the electrode cable to the output terminal of

polarity required by electrode. Connect the work lead tothe other terminal.

• LN-25 with Remote Control options can be used with the"CE" version of the V350. The 6 Pin (K444-1) and 14 pin(K444-2) remotes can be connected directly to the 6 & 14pin amphenols. The 42 Volt Remote Voltage and OutputControl (K624-1) Kit can be connected to the V350’s24/42 VAC amphenol using Remote Control Cableassembly K627- [ ]. LN-25s with a K431-1 remote kit canbe connected to the V350’s 24/42 VAC amphenol using aK432 cable and K876 adapter. (See connection diagramS19899). Or the K432 cable could be modified with aK867 Universal Adapter Plug (See connection diagramS19405) to connect it to the V350’s 24/42 VAC amphenol.

LN-7 Connection Instructions • Turn the Invertec power switch "off".• Connect the K480 control cable from the LN-7 to the

115VAC 14-pin wire feeder amphenol connector onthe rear of the Invertec.

• Connect the electrode cable to the output terminal ofthe polarity required by electrode. Connect the worklead to the other terminal.

• Set the meter polarity switch on the front of theInvertec to coincide with wire feeder polarity used.The wire feeder will now display the welding voltage.

• If K480 is not available, see connection diagramS19404 for modification of K291 or K404 LN-7 inputcable with K867 Universal Adapter Plug.

• If a remote control such as K857 is to be used withthe LN-7, the remote can be connected directly tothe 6 pin amphenol on the front of the Invertec oruse a K864 adapter to connect the LN-7 and theremote to the 115VAC 14-pin amphenol connectoron the rear of the Invertec. (See connection diagramS19901)

WARNING

REMOTE

POWER

OFF

ON

A AMPS

A

V VOLTS

WELD TERMINALS

SELECT

OUTPUTLINCOLNELECTRIC

INVERTEC V350-PRO

WARNINGWARNING

AVISO DE

PRECAUCION

ATTENTION

!

!

!

!



elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non







elit, ed diam non





GREEN/YELLOWBLUE

BLACK

BROWN

V350-PRO (CE)

A-3INSTALLATION A-3

V350-PRO (CE)

LN-10 Connection Instructions• Turn the Invertec power switch "off".• Connect the K1505 control cable from the LN-10 to

the Invertec 24/42VAC 14-pin amphenol connectoron the rear of the Invertec.

• Connect the electrode cable to the output terminalof polarity required by the electrode. Connect thework lead to the other terminal.

• Set the meter polarity switch on the front of theInvertec to coincide with wire feeder polarity used.

• See the LN-10 manual for details on accessingControl DIP Switch

LN-742 Connection Instructions• Turn the Invertec power switch "off"• Either a K591 or a K593 Input cable assembly is

required to connect the LN-742 to the Invertec. • Connect the control cable from the LN-742 to the

24/42 VAC 14-pin wire feeder amphenol on the rearof the Invertec.

• Connect the electrode cable to the output terminalof the polarity required by electrode. Connect thework lead to the other terminal.

• Set the meter polarity switch on the front of theInvertec to coincide with wire feeder polarity used.The wire feeder will now display the welding volt-age.

• If a remote control such as K857 is to be used withthe LN-742, the remote can be connected directly tothe 6pin amphenol on the front of the Invertec or usea K864 adapter to connect the LN-742 and theremote to the 24/42VAC 14-pin wire feeder amphe-nol connector on the rear of the Invertec.

Cobramatic Connection Instructions• Turn the Invertec power switch "off"• Connect the control cable from the Cobramatic to

the 24/42 VAC 14-pin wire feeder amphenol on therear of the Invertec.

• Connect the electrode cable to the output terminalof the polarity required by electrode. Connect thework lead to the other terminal.

• Set the meter polarity switch on the front of theInvertec to coincide with wire feeder polarity used.

• If a remote control such as K857 is to be used withthe Cobramatic, the remote can be connecteddirectly to the 6pin amphenol on the front of theInvertec or use a K864 adapter to connect thecobramatic and the remote to the 24/42VAC 14-pinwire feeder amphenol connector on the rear of theInvertec.

TIG MODULE K930-2The TIG Module connects to the “CE” version with aK936-1 (9-14 pin) control cable. Connect the K936-1to the 115VAC Wire Feeder Amphenol on the rear ofthe V350-PRO (CE).

CONNECTION OF WIRE FEEDERS TO V350-PRO (CE)Wire feeders other than LN-7, LN-10 and LN-25 maybe used provided that the auxiliary power supplycapacity of the Invertec is not exceeded. K867Universal Adapter Plug may be required. See con-nection diagram S24985 on page F-4.

REMOTE CONTROL OF INVERTECRemote Control K857, Hand Amptrol K963 and FootAmptrol K870.

UNDERCARRIAGE MOUNTINGS

5.50

10.00

MOUNTING HOLE LOCATIONS

M19527

1/4-20 NUT (4 PLACES)

NOTE: MOUNTING SCREWS CA

8/00

N NOT PROTRUDE MORE THAN 0.5 INCHES INSIDE THE MACHINE.

11.84

3.50

A-4INSTALLATION A-4

V350-PRO (CE)

PARALLEL OPERATIONThe V350-PRO (CE) are operable in parallel in CCmode. For best results, the currents of each machineshould be reasonably well shared. As an example,with two machines set up in parallel for a 400 ampprocedure, each machine should be set to deliverapproximately 200 amps, not 300 amps from one and100 amps from the other. This will minimize nuisanceshutdown conditions. In general, more than twomachines in parallel will not be effective due to thevoltage requirements of procedures in that powerrange.To set machine outputs, start with output control potsand arc control pots in identical positions. Use theoutput control pots to balance the currents and main-tain the desired voltage or current. The arc controlpots should be kept identical on the two machines.

QUICK DISCONNECT PLUGS

A quick disconnect system is used for the weldingcable connections. The welding plug included with themachine is designed to accept a welding cable size of1/0 to 2/0.

1. Remote 25mm (1 in.) of welding cable insulation.

2. Slide rubber boot onto cable end. The boot endmay be trimmed to match the cable diameter.Soap or other lubricant will help to slide the bootover the cable.

3. Slide the copper tube into the brass plug.

4. Insert cable into copper tube.

5. Tighten set screw to collapse copper tube. Screwmust apply pressure against welding cable. Thetop of the set screw will be well below the surfaceof the brass plug after tightening.

6. Slide rubber boot over brass plug. The rubberboot must be positioned to completely cover allelectrical surfaces after the plug is locked into thereceptacle.

25 mm

1 in.

WELDING CABLE

BOOT

TRIM

SET SCREW

BRASS PLUGCOPPER TUBE

B-1OPERATION

V350-PRO (CE)

B-1

SAFETY PRECAUTIONS

ELECTRIC SHOCK can kill.• Do not touch electrically live parts orelectrode with skin or wet clothing.• Insulate yourself from work andground.• Always wear dry insulating gloves.

------------------------------------------------------------------------FUMES AND GASES can be danger-ous.• Keep your head out of fumes.• Use ventilation or exhaust to removefumes from breathing zone.

------------------------------------------------------------------------WELDING SPARKS can cause fire orexplosion.• Keep flammable material away.• Do not weld on closed containers.

------------------------------------------------------------------------ARC RAYS can burn eyes and skin.• Wear eye, ear and body protection.

------------------------------------------------------------

See additional warning information atfront of this operator’s manual.

-----------------------------------------------------------

WARNING

GENERAL DESCRIPTION

PRODUCT DESCRIPTION & DUTY CYCLEThe Invertec V350-PRO (CE) offers multi mode CVand CC DC welding and is rated at 350 amps, 34 voltsat a 60% duty cycle with 3 phase input. It is also ratedat 320 amps with single phase input. It is rated at 275amps, 100% duty cycle.

OPERATIONAL FEATURES and CONTROLS:

UPPER CONTROL PANEL1. AMPS Meter• Prior to STICK or TIG operation (current flow), the

meter displays preset current value (either 2 ampsor +/- 3% (e.g. 3 amps on 100), whichever isgreater).

• Prior to CV operation, the meter displays four dash-es indicating non-presettable AMPS.

• During welding, this meter displays actual averageamps.

• After welding, the meter holds the actual currentvalue for 5 seconds. Output adjustment while in the"hold" period results in the "prior to operation" char-acteristics stated above. The displays blink indicat-ing that the machine is in the "Hold" period.

2. VOLT METER• Prior to CV operation (current flow), the meter dis-

plays desired preset voltage value (+/- .5V).• Prior to STICK or TIG operation, the meter displays

the Open Circuit Voltage of the Power Source orfour dashes if the output has not been turned on.

• During welding, this meter displays actual averagevolts.

• After welding, the meter holds the actual voltagevalue for 5 seconds. The displays blink indicatingthat the machine is in the "Hold" period.

• Output adjustment while in the "hold" period resultsin the "prior to operation" characteristics statedabove.

3. OUTPUT CONTROL• Output control is conducted via a single turn poten-

tiometer.• Adjustment is indicated by the meters as stated

above.• When in TIG modes, this control sets the maximum

welding current. Full depression of a foot or handAmptrol results in the preset level of current.

4. WELD TERMINALS-REMOTE , ON• Two status lights indicate the location of trigger con-

trol as determined by the "WELD TERMINALS"push button.

• If trigger control is local "weld terminals on", the ONdisplay will be lit.

• If trigger control is remote "weld terminals remotelycontrolled", the REMOTE display will be lit.

• The unit will power up in "pre-determined preferred"trigger modes.

STICK = ON TIG and CV = ON or REMOTE depending if remoteoutput controls are connected to the machine.

B-2OPERATIONB-2

5. THERMAL• This status light indicates when the power source

has been driven into thermal overload. If the outputterminals were "ON", the "ON" light will blink indicat-ing that the output will be turned back on once theunit cools down to an acceptable temperature level.If the unit was operating in the "REMOTE" mode,the trigger will need to be opened before or after thethermal has cleared and closed after the machinehas cooled down to an acceptable temperature toestablish output.

6. CONTROL-REMOTE , LOCAL• Two status lights indicate the location of output con-

trol as pre-determined by the power sources auto-configure system.

• The LOCAL display will be lit when control is at thepower source.

• The REMOTE display will be lit when a remotepot/control is detected.

These Output Control configurations can be overrid-den (switched) with the CONTROL push button.When changed, the unit will power up in the configura-tion it was in when it was last powered down.

Hidden Middle Control Panel – ProcessSet Up PanelThe middle control panel is removable to allow forupgrades (see Field Installed Options/Accessories).Additionally, this panel is hidden by an access door toreduce appeared complexity and provide protection tothe controls.

7. WELD MODE SELECTThe Mode Control button selects the following weldingmodes desired.

CC-STICK SOFT: The Stick Soft process featurescontinuous control ranging from 5 to 425 amps. Thismode was intended for most SMAW applications, andArc Gouging.

• Arc Gouging: Setting the output of the Stick Softmode to 425 amps will enable the arc-gougingmode. The actual output current will depend on thesize of carbon used. The recommended maximumsize carbon is 5/16".

• The Hot Start control regulates the starting currentat arc initiation. Hot Start can be adjusted from min-imum (0), with no additional current added at arcstart, to maximum (10), with double the preset cur-rent or 425 amps (max of machine) added for thefirst second after arc initiation.

• The Arc Control regulates the Arc Force to adjustthe short circuit current. The minimum setting (-10)will produce a "soft" arc and will produce minimalspatter. The maximum setting (+10) will produce a"crisp" arc and will minimize electrode sticking.

CC-STICK CRISP: The Stick Crisp mode featurescontinuous control from 5 to 425 amps. This modewas intended primarily for pipe welding applications.

• The Hot Start control regulates the starting currentat arc initiation. Hot Start can adjust starting currentup or down by 25% of the preset value. The recom-mended setting for Hot Start is 5 where the initialcurrent is equal to the preset current.

V350-PRO (CE)

OFFOFF

OFF OFF OFFOFFONON

HOHOT STT STARARTWELD MODEWELD MODE ARC CONTRARC CONTROLOL

CC-STICK SOFTCC-STICK SOFT

CC-STICK CRISPCC-STICK CRISP

TIG GTTIG GTAW

CVCV-WIRE-WIRE

CVCV-FLUX CORED-FLUX CORED

-4 +4+4

+2+2-20

-6 +6+6

-10-10SOFTSOFT CRISPCRISP

+10+10

-8 +8+8

54

3

2

1

0

6

1010

9

8

7

SELECTSELECT

REMOREMOTETEONON

REMOREMOTETELOCALLOCAL

m

WELDWELD TERMINALSTERMINALS

OUTPUTOUTPUT

CONTRCONTROL

SELECTSELECT SELECTSELECT

MPSMPSA OLOLTSV

1

6

52

3

4

8

7

11

10

12 9

B-3OPERATIONB-3

• The Arc Control regulates the relative Slope of theprocess. Slope dynamically controls the force thearc has to penetrate an open root. At the minimumsetting, Arc Control is very soft and is similar to theStick Soft mode. At the maximum setting, the slopeis reduced, the OCV is reduced, and the operatorhas full control off the arc force required to pene-trate an open root joint. For vertical down, open rootpipe welding applications, the recommended settingis between 8 and 10.

• During welding, a boost circuit increases the avail-able voltage to minimize pop outs. The boost circuitis independent of the OCV and only operates whenan arc is lit.

TIG GTAW: The TIG mode features continuous con-trol from 5 to 425 amps. The TIG mode can be run ineither the TIG touch start or high frequency assistedstart mode.

• The Hot Start control selects the starting modedesired. A setting of less than 5, the TIG lift startmode is selected. The OCV is controlled below 10vand the short circuit "TIG touch" current is main-tained at 25 amps independent of the preset current.When the tungsten is lifted, an arc is initiated and theoutput is regulated at the preset value. Hot start set-tings between 0 and 5 regulate the arc initiation cur-rent. A setting of 5 results in the most positive arc ini-tiation. A setting of 0 reduces hot start.

• Hot Start settings between 5 and 10, select high fre-quency assisted starting TIG mode. In this range, theOCV of the machine is controlled between 50 and 70volts. If using the Lincoln K930-1 TIG Module, setthe Hot start to 10 for maximum OCV.

• The Arc Control is not used in the TIG mode.

CV-WIRE: The CV-WIRE mode features continuouscontrol from 10 to 45 volts. The mode was intendedfor most GMAW, FCAW, and MCAW applications.

• The Hot Start control is not used in the CV-WIREmode.

• The Arc Control regulates pinch effect. At the mini-mum setting (-10), minimizes pinch and results in asoft arc. Low pinch settings are preferable for weld-ing with gas mixes containing mostly inert gases. Atthe maximum setting (+10), maximizes pinch effectand results in a crisp arc. High pinch settings arepreferable for welding FCAW and GMAW with CO2.

CV-INNERSHIELD: The CV-INNERSHIELD modefeatures continuous control from 10 to 45 volts. Thismode was designed for self-shielded flux cored wiresthat require tight voltage control.

• The Hot Start control is not used in the CV-FLUXCORED mode.

• The Arc Control regulates pinch effect. At the mini-mum setting (-10), minimizes pinch and results in asoft arc. At the maximum setting (+10), maximizespinch effect and results in a crisp arc. Most self-shielded wires work well at an Arc Control setting of 5.

8. HOT START and ARC CONTROL features havedifferent functions depending on the welding Modethat is active. Each feature is described under thewelding mode heading. (See Item 6 for specifiedMode Operation)

LOWER CASE FRONTThe output studs, line switch and remote connectorare located on the lower case front.

9. Both STUDS contain "Twist-Mate" connectorinserts.

• The Negative stud is configured to accept thepass through gas system.

10. The ON-OFF switch is a 3-phase circuit breakerrated at 100 amps per leg.

11. The METER POLARITY switch is located abovethe output connectors. The switch provides a workconnection for wire feeder voltmeters. Place theswitch in the position of the electrode polarity indi-cated by the decal. The switch does not changethe welding polarity.

12. 6-PIN AMPENOL for remote control.

REMOTE CONTROL of the OUTPUT CON-TROL and WELD TERMINALSThe Invertec V350-PRO (CE) has auto sensing ofremote output controls.If after connecting or removinga remote, the Invertec V350-PRO (CE) did not config-ured the way you would like the local or remote con-trol settings can be changed by pushing the OUTPUTCONTROL or WELD TERMINAL button. (A user can-not select between the 6 and 14 pin amphenols.)

CV modes• The remote will default to the 14-pin amphenol

remote if a remote is connected to either of the 14-pin amphenols and the 6-pin amphenol. Note: Onlyone of the 14-pin amphenols can have a remotecontrol connected at a time. If no remote is connect-ed to either of the 14-pin amphenols then theremote will default to the 6-pin amphenol if a remoteis connected to it.

• If a remote control is connected or is not connect-ed to any of the amphenols the WELD TERMINALcontrol will default to REMOTE.

V350-PRO (CE)

B-4OPERATIONB-4TIG mode• The remote will default to the 6-pin amphenol if a

remote control is connected to the 6-pin amphenoland one of the 14-pin amphenols. If a remote is notconnected to the 6-pin amphenol then the remotewill default to the 14-pin amphenols if a remote isconnected to one of the 14-pin amphenols.

• If a remote control is connected to any of theamphenols the WELD TERMINAL control willdefault to REMOTE. If there are not any remotecontrol devices attached the WELD TERMINAL con-trol will default to ON.

CC-Stick modes • The remote will default to only the 6-pin amphenol if

a remote is connected to it.• The WELD TERMINAL control will default to ON

with or without a remote connected.

Types of Remote OUTPUT CONTROL• The Invertec V350-PRO (CE)’s Output Control can

be controlled by either a potentiometer connectedbetween 77 & 75 with the wiper connected to 76 ora 0V to 10V DC supply connected between 76 & 75.(76 needs to be positive)

• 14-Pin Amphenol lead 75 is pin G, lead 76 is pin Fand lead 77 is pin E.

• 6-Pin Amphenol lead 75 is pin C, lead 76 is pin Band lead 77 is pin A.

Potentiometer Control• The total resistance should be between 2000 ohms

(2K) and 10,000 ohms (10K)• The machine output will be at minimum when lead

76 (wiper) is at the end of the potentiometer that isconnected to 75. The machine’s output will increaseas the wiper of the potentiometer is moved to theend that is connected to 77. (Note: In TIG mode,moving the lead 76 (wiper) to lead 77 would pro-duce the current that has been set by the InvertecV350-PRO (CE)’s front panel Output Control.)

• Remotes of this type offered by Lincoln Electric arethe K857, K812 and K870.

Voltage Control• The supply should be an isolated supply. (Not refer-

enced to earth ground, any auxiliary power from theInvertec V350-PRO (CE) or the welding output) Thesupply should be capable of supplying at least 20mA.

• 0 volts supplied to 76 will set the Invertec V350-PRO (CE) to minimum output for the mode that hasbeen selected while 10 volts supplied to 76 will setthe Invertec V350-PRO (CE) to the maximum outputfor the mode. (Note: In TIG mode, 10 volts suppliedto lead 76 would produce the current that has beenset by the Invertec V350-PRO (CE)’s front panelOutput Control.)

Types of Remote WELD TERMINAL Control• The Invertec V350-PRO (CE)’s Weld Terminals can

be controlled from each of the amphenol connec-tors. The circuit has a nominal OCV of 15VDC andrequires a dry contact closure (less than 100 ohms)to activate the output of the Invertec V350-PRO(CE).

• 14 Pin Amphenols the Weld Terminals are controlledfrom pins C (lead 2) and pin D (lead 4). Pin C is posi-tive.

• 6 Pin Amphenol the Weld Terminals are controlledfrom pin D (lead 2) and pin E (lead 4). In the 6-pinamphenol pin D is positive.

DESIGN FEATURES and ADVANTAGES • Multiple process DC output range: 5 - 425 amps• Pre-settable welding outputs.• Built-in Line Voltage Compensation holds the output

constant over +/- 10% input fluctuations.• State of the art inverter technology yields high

power efficiency, excellent welding performance,lightweight, and compact design.

• Utilizes microprocessor control.• Electronic over current protection.• Input over voltage protection• Manual reconnect switch located on the back panel

with a clear reconnect door to allow easy determina-tion of input configuration. The reconnect door isfastened with 1/4-turn connectors that allow quickand easy access to the reconnect area. Circuitbreaker protected auxiliary.

• System Self Configure. The power source analyzesthe remote controls connected to the amphenolsand the desired welding mode to properly determinethe location of trigger and output control.

• Modular options for easy upgrades• Back lit Status Lights for improved error communi-

cation• Circuit Breaker Input Switch• F.A.N. (fan as needed). Cooling fan runs only when

necessary• Thermostatically protected.• Designed to the IEC 974-1 Standard.• IP21S protection rating with potted PC boards for

enhanced ruggedness/reliability.• Modular construction for easy servicing.• Aluminum Chassis and Wraparound• Power Cord included.

V350-PRO (CE)

B-5OPERATIONB-5AUXILIARY POWER• 115VAC, 42VAC and 24VAC power is available

from the two 14-pin amphenols on the rear of theunit. (K1728-2 Construction model of the InvertecV350-PRO (CE) does not have the amphenols)These supplies are intended to supply power forauxiliary equipment like wire feeders and the TIGModule.

• 115VAC supply is rated at 2 amps and is protectedby a 2.5 amp breaker located by the amphenol.

• 42 VAC supply is rated at 5.5 amps and is protectedby a 6 amp breaker located by the amphenol.

• 24 VAC supply is rated at 5.5 amps and is protectedby a 6 amp breaker located by the amphenol.

LIMITATIONS• The V350-PRO (CE) is not recommended for

processes other than those listed.• The V350-PRO (CE) can only be used with the rec-

ommended equipment and options.

RECOMMENDED PROCESSESProperly equipped, the Invertec V350-PRO (CE)supports GMAW, FCAW, SMAW, GTAW and CAC-A processes for a variety of materials, includingmild steel, stainless steel, cored wires, and alu-minum

V350-PRO (CE)

C-1ACCESSORIESC-1

OPTIONS / ACCESSORIES

"CE" VERSION – K1728-3

• The "CE" version is the Factory version with theaddition of power line filtering allowing the machineto comply with the European and Australian EMCemission requirements.

• In this form, the V350-PRO (CE) provides the hard-ware to power and connect to 24, 42 or 115 VAC wirefeeders.

K857 Remote Output ControlK814 Arc Start SwitchK812 Hand Operated AmptrolK870 Foot Operated AmptrolK930-1 TIG ModuleK428, K446, K449 LN-25K617 (-1 or -2) K618 (-1 or -2) LN-742K440 (-1), K567-1 LN-7 GMAK1559-1, K1564-1 LN-10K1499-1, K1521-1 DH-10

FIELD INSTALLED OPTIONS/ACCESSORIES

Options for K1728-1 Factory and K1728-3 "CE"V350’s• TIG Gas Control Kit – K1762-1

• Advance Process Panel – K1763-1

• Undercarriage – K1764-1

• Valet Style Undercarriage – K1838-1

V350-PR0 (CE)

D-1MAINTENANCED-1

VISUAL INSPECTION

Clean interior of machine with a low pressure airstream. Make a thorough inspection of all compo-nents. Look for signs of overheating, broken leads orother obvious problems. Many problems can beuncovered with a good visual inspection.

ROUTINE MAINTENANCE

1. Every 6 months or so the machine should becleaned with a low pressure airstream. Keepingthe machine clean will result in cooler operationand higher reliability. Be sure to clean these areas:

• All printed circuit boards• Power switch• Main transformer• Input rectifier • Auxiliary Transformer• Reconnect Switch Area

2. Examine the sheet metal case for dents or breakage.Repair the case as required. Keep the case in good con-dition to insure that high voltage parts are protected andcorrect spacings are maintained. All external sheetmetal screws must be in place to insure case strengthand electrical ground continuity.

PERIODIC MAINTENANCE

Overload ProtectionThe machine is electrically protected from producinghigh output currents. Should the output currentexceed 430A, an electronic protection circuit willreduce the current to approximately 100A. Themachine will continue to produce this low current untilthe protection circuit is reset. Reset occurs when theoutput load is removed.

Thermal ProtectionThermostats protect the machine from excessiveoperating temperatures. Excessive temperatures maybe caused by a lack of cooling air or operating themachine beyond the duty cycle and output rating. Ifexcessive operating temperature should occur, thethermostat will prevent output voltage or current. Themeter will remain energized during this time.

Thermostats are self-resetting once the machine coolssufficiently. If the thermostat shutdown was caused byexcessive output or duty cycle and the fan is operatingnormally, the Power Switch may be left on and thereset should occur within a 15 minute period.

V350-PRO (CE)

SAFETY PRECAUTIONS

-----------------------------------------------------------------------

ELECTRIC SHOCK can kill.• Do not touch electrically live parts or

electrode with skin or wet clothing.• Insulate yourself from work and

ground• Always wear dry insulating gloves.

------------------------------------------------------------------------EXPLODING PARTS can causeinjury.• Failed parts can explode or cause otherparts to explode when power is applied.

• Always wear a face shield and longsleeves when servicing.

------------------------------------------------------------------------See additional warning informationthroughout this operator’s manual andthe Engine manual as well.

-----------------------------------------------------------

WARNING

CAPACITOR DISCHARGE PROCEDURE1. Obtain a power resistor (25 ohms, 25 watts).

2. Hold resistor body with electrically insulated glove.DO NOT TOUCH TERMINALS. Connect the resis-tor terminals across the two studs in the positionshown. Hold in each position for 1 second. Repeatfor all four capacitors.

3. Use a DC voltmeter to check that voltage is notpresent across the terminals on all four capacitors.

CAPACITORTERMINALS

RESISTOR

E-1TROUBLESHOOTINGE-1

V350-PRO (CE)

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

CAUTION

This Troubleshooting Guide is provided to help youlocate and repair possible machine malfunctions.Simply follow the three-step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).Look under the column labeled “PROBLEM (SYMP-TOMS)”. This column describes possible symptomsthat the machine may exhibit. Find the listing thatbest describes the symptom that the machine isexhibiting.

Step 2. POSSIBLE CAUSE.The second column labeled “POSSIBLE CAUSE” liststhe obvious external possibilities that may contributeto the machine symptom.

Step 3. RECOMMENDED COURSE OF ACTIONThis column provides a course of action for thePossible Cause, generally it states to contact yourlocal Lincoln Authorized Field Service Facility.

If you do not understand or are unable to perform theRecommended Course of Action safely, contact yourlocal Lincoln Authorized Field Service Facility.

HOW TO USE TROUBLESHOOTING GUIDE

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.Unauthorized repairs performed on this equipment may result in danger to the technician andmachine operator and will invalidate your factory warranty. For your safety and to avoid ElectricalShock, please observe all safety notes and precautions detailed throughout this manual.

__________________________________________________________________________

WARNING


V350-PRO (CE)


CAUTION

Observe all Safety Guidelines detailed throughout this manualPROBLEMS

(SYMPTOMS)POSSIBLE AREAS OFMISADJUSTMENT(S)

RECOMMENDEDCOURSE OF ACTION

Major physical or electrical damageis evident when the sheet metalcovers are removed.

Input fuses keep blowing, or inputbreaker keeps tripping

Machine will not power up (Nolights)

Machine won’t weld, can’t get anyoutput.

1. Contact your local authorizedLincoln Electric Field Servicefacility for technical assistance.

1. Make certain that the fuses orbreakers are properly sized. Seeinstallation section of the manualfor recommended fuse andbreaker sizes.

2. Welding procedure is drawing toomuch output current, or dutycycle is too high. Reduce outputcurrent, duty cycle or both.

3. There is internal damage to thepower source. Contact an autho-rized Lincoln Electric Servicefacility.

1. Make certain that the powerswitch is in the "ON" position.

2. The circuit breaker in the recon-nect area may have opened.Reset. Check input voltage sec-tion below.

3. Input voltage selection madeimproperly. Power down, checkinput voltage reconnect accord-ing to diagram on reconnectcover.

1. If the displays show an Err ###see the fault section for correc-tive action.

2. If the displays are not lit refer tomachine will not power up sec-tion.

3. If the thermal symbol is lit refer tothe thermal section.

4. If the output terminals are inRemote control switch to "ON"and check for output voltage. Ifoutput voltage is now presentcheck for correct remote controlconnection and operation.

If all recommended possible areasof misadjustment have beenchecked and the problem persists,Contact your local LincolnAuthorized Field Service Facility.


V350-PRO (CE)

Observe all Safety Guidelines detailed throughout this manual


CAUTION

PROBLEMS(SYMPTOMS)

POSSIBLE AREAS OFMISADJUSTMENT(S)

RECOMMENDEDCOURSE OF ACTION

Thermal symbol is lit

Wire feeder won’t work. Apparentlyno power to wire feeder

1. Check for proper fan operation2. Check for material blocking

intake or exhaust louvers.

1. Check circuit breakers by thewire feeder receptacles on therear of the machine. Reset

2. Check to make sure the wirefeeder is connected to the correctwire feeder receptacle. (115VACor 24/42VAC)

3. Check the control cable betweenthe power source and the wirefeeder for continuity.

If all recommended possible areasof misadjustment have beenchecked and the problem persists,Contact your local LincolnAuthorized Field Service Facility.


V350-PRO (CE)



CAUTION

Fault Codes

Code Description Corrective Action31 Primary over current. If condition persists The machine needs to

contact an authorized be turned off and backLincoln Field Service on to reset the machine.Shop

32 CAP bank A under voltage. Check input power Self-clearing as33 CAP bank B under voltage. reconnect to make sure condition ceases.34 CAP bank A over voltage. the machine 35 CAP bank B over voltage. is connected for the input 37 Soft start Failed. power being supplied. Cycle power.39 Glitch on the primary over Check the machine Self-clearing as

current fault interrupt; possibly ground. condition ceases.caused by noise or a signal level If problem persists(misc. hardware fault #1) contact an authorized

Lincoln Field Service Shop

43 CAP delta; CAP A and B are out Check input powerof balance. reconnect to make sure

the machine isconnected for the inputpower being supplied.

44 Main CPU problem. The DSP Check the machinehas detected a problem with the ground.CPU.

47 Glitch on the CAP/heart beat If problem persistsinterrupt; possibly caused by contact an authorizednoise or a signal level right at Lincoln Field Servicethe trip threshold. Shop(misc. hardware fault #2)

48 The main contactor opened If condition persist Self-clearingunexpectedly. (misc. hardware contact an authorizedfault #3) Lincoln Field Service

Shop"bad The selected weld mode does If condition persists Press the Modenode’ not exist in the weld table that is contact an authorized Select button to “####” presently loaded in the machine. Lincoln Field Service select a different

Shop mode


V350-PRO (CE)



CAUTION

Displays Description

Scrolling dash Appears at power up while the machine is going through its self configu-ration

"Err" "####" Fault code display. The first fault to occur will be displayed for threeseconds. The display will cycle through fault codes for all faults thatpersist after the initial three-second period are displayed for 1 sec-ond each.

"----" "----" Weld mode is changing

"----" "####" A constant voltage weld mode is selected, machine output is off.The numeric value in the right display is the workpoint.

"####" "----" A constant current weld mode is selected, machine output is off.The numeric value in the left display is either the workpoint or aworkpoint limit, depending on the weld mode and remote configura-tion.

"####" "####"(on steady) machine output is on. Left display is current, right display is voltage.If actively welding, the displays are arc current and arc voltage. Ifnot actively welding, the display will show workpoint.

"####" "####" (blinking) weld just finished – the average arc voltage and current will beblinked for 5 seconds following a weld. If the workpoint changes dur-ing this 5 second period, the display will revert to the above mode.

F-1DIAGRAMSF-1

V350-PRO (CE)

TU

RN

TH

E P

OW

ER

SW

ITC

H O

F T

HE

WE

LD

ING

PO

WE

RS

OU

RC

E "

OF

F"

BE

FO

RE

IN

ST

AL

LIN

G P

LU

GS

ON

CA

BL

ES

OR

WH

EN

CO

NN

EC

TIN

G O

R D

ISC

ON

NE

CT

ING

PL

UG

S T

OW

EL

DIN

G P

OW

ER

SO

UR

CE

.

ST

RA

IGH

T P

LU

G (

14

PIN

)T

O P

OW

ER

SO

UR

CE

CA

BL

E R

EC

EP

TA

CL

E (

6 S

OC

KE

T)

CA

BL

E R

EC

EP

TA

CL

E (

14

SO

CK

ET

)

TO

: 1

) L

N-7

WIR

E F

EE

DE

RS

TO

: 1

) K

85

7 R

EM

OT

E C

ON

TR

OL

2

) K

96

3 H

AN

D A

MP

TR

OL

3

) K

87

0 F

OO

T A

MP

TR

OL

K8

64 S

TR

AIG

HT

PL

UG

(1

4 P

IN)

TO

PO

WE

R S

OU

RC

E

K8

76

CA

BL

E R

EC

EP

TA

CL

E (

6 S

OC

KE

T)

TO

: 1

) L

N-2

5 W

IRE

FE

ED

ER

S

S

1930

9

4-

19-9

6D

REM

OTE

CO

NTR

OL

AD

APT

ERS

F-2DIAGRAMSF-2

V350-PRO (CE)

N.A

. W

EL

DIN

G C

AB

LE

MU

ST

BE

SIZ

ED

FO

R C

UR

RE

NT

AN

D D

UT

Y C

YC

LE

OF

AP

PL

ICA

TIO

N.

N.B

. D

IAG

RA

M S

HO

WS

EL

EC

TR

OD

E P

OS

ITIV

E.

TO

CH

AN

GE

PO

LA

RIT

Y,

TU

RN

PO

WE

R "

OF

F",

RE

VE

RS

E E

LE

CT

RO

DE

AN

D W

OR

K C

AB

LE

AT

PO

WE

R S

OU

RC

E.

N.C

. I

NS

UL

AT

E E

AC

H U

NU

SE

D L

EA

D I

ND

IVID

UA

LL

Y.

EL

EC

TR

OD

E C

AB

LE

TO

LN

-7

TO

WO

RK

- +

14

PIN

AM

PH

EN

OL

SP

AR

E8

28

14

24

1

31

32 2 4 21

GN

D

75

76

77

31

32 2 4 21

GN

D

N.C

.

K2

91

OR

K4

04

INP

UT

CA

BL

E

K7

75

OP

TIO

NA

LR

EM

OT

E C

ON

TR

OL

K8

67

UN

IVE

RS

AL

AD

AP

TE

R P

LU

G

LN

-7C

ON

TR

OL

BO

X

75

76 77G

RE

EN

N.D

.

N.D

. S

PL

ICE

LE

AD

S A

ND

IN

SU

LA

TE

.

PO

WE

R S

OU

RC

E

AU

XIL

IAR

Y P

OW

ER

Onl

y qu

alifi

ed p

erso

ns s

houl

d in

stal

l, us

e or

serv

ice

this

mac

hine

.

usin

g th

e di

scon

nect

sw

itch

at t

he f

use

box

WARN

INGTu

rn o

ff in

put

pow

er t

o th

e W

eldi

ng P

ower

Sou

rce

Befo

re c

onne

ctin

g th

e w

ire

feed

er.

ELEC

TRIC

SHOC

K

CAN

KILL

INV

ER

TE

C

WIT

H 1

15

VA

C

S19

404

N.A

. W

EL

DIN

G C

AB

LE

MU

ST

BE

SIZ

ED

FO

R C

UR

RE

NT

AN

D D

UT

Y C

YC

LE

OF

AP

PL

ICA

TIO

N.

N.B

. D

IAG

RA

M S

HO

WS

EL

EC

TR

OD

E P

OS

ITIV

E.

TO

CH

AN

GE

PO

LA

RIT

Y,

TU

RN

PO

WE

R "

OF

F",

RE

VE

RS

E E

LE

CT

RO

DE

AN

D W

OR

K C

AB

LE

AT

PO

WE

R S

OU

RC

E.

N.C

. I

NS

UL

AT

E E

AC

H U

NU

SE

D L

EA

D I

ND

IVID

UA

LL

Y.

EL

EC

TR

OD

E C

AB

LE

TO

LN

-7

TO

WO

RK

- +

14

PIN

AM

PH

EN

OL

SP

AR

E8

28

14

24

1

31

32 2 4 21

GN

D

75

76

77

31

32 2 4 21

GN

D

N.C

.

K2

91

OR

K4

04

INP

UT

CA

BL

E

K7

75

OP

TIO

NA

LR

EM

OT

E C

ON

TR

OL

K8

67

UN

IVE

RS

AL

AD

AP

TE

R P

LU

G

LN

-7C

ON

TR

OL

BO

X

75

76 77G

RE

EN

N.D

.

N.D

. S

PL

ICE

LE

AD

S A

ND

IN

SU

LA

TE

.

PO

WE

R S

OU

RC

E

AU

XIL

IAR

Y P

OW

ER

Onl

y qu

alifi

ed p

erso

ns s

houl

d in

stal

l, us

e or

serv

ice

this

mac

hine

.

usin

g th

e di

scon

nect

sw

itch

at t

he f

use

box

WARN

INGTu

rn o

ff in

put

pow

er t

o th

e W

eldi

ng P

ower

Sou

rce

Befo

re c

onne

ctin

g th

e w

ire

feed

er.

ELEC

TRIC

SHOC

K

CAN

KILL

INV

ER

TE

C

WIT

H 1

15

VA

C

S19

404

12

-10-

93A

K86

7 PL

UG

TO

LN

-7 -

CO

NN

ECTI

ON

DIA

GR

AM

F-3DIAGRAMSF-3

V350-PRO (CE)

N.A

. W

EL

DIN

G C

AB

LE

MU

ST

BE

SIZ

ED

FO

R C

UR

RE

NT

AN

D D

UT

Y C

YC

LE

OF

AP

PL

ICA

TIO

N.

N.B

. D

IAG

RA

M S

HO

WS

EL

EC

TR

OD

E P

OS

ITIV

E.

TO

CH

AN

GE

PO

LA

RIT

Y,

TU

RN

PO

WE

R "

OF

F",

RE

VE

RS

E E

LE

CT

RO

DE

AN

D W

OR

K C

AB

LE

AT

PO

WE

R S

OU

RC

E.

N.C

. I

NS

UL

AT

E E

AC

H U

NU

SE

D L

EA

D I

ND

IVID

UA

LL

Y.

TO

WO

RK

- +

14

PIN

AM

PH

EN

OL

N.C

.E

LE

CT

RO

DE

CA

BL

ET

O L

N-2

5

K8

67

AD

AP

TE

R

LN

-25

WIT

HK

43

1 O

PT

ION

K4

32

RE

MO

TE

CO

NT

RO

L C

AB

LE

E F D A B C7

77

67

5S

PA

RE

4221

82

81

42

41

GN

D3

13

2

N.D

.

N.D

. R

EM

OV

E 6

PIN

PL

UG

FR

OM

K

43

2 C

AB

LE

IN

OR

DE

R T

O C

ON

NE

CT

K8

67

PL

UG

.

L

AB

EL

EA

CH

LE

AD

(A

TH

RU

F)

AS

TH

EY

AR

E R

EM

OV

ED

FR

OM

6 P

IN P

LU

G.

N.E

.

N.E

. S

PL

ICE

LE

AD

S A

ND

IN

SU

LA

TE

.

Onl

y qu

alifi

ed p

erso

ns s

houl

d in

stal

l, us

e or

serv

ice

this

mac

hine

.

usin

g th

e di

scon

nect

sw

itch

at t

he f

use

box

WARN

INGTu

rn o

ff in

put

pow

er t

o th

e W

eldi

ng P

ower

Sou

rce

Befo

re c

onne

ctin

g th

e w

ire

feed

er.

ELEC

TRIC

SHOC

K

CAN

KILL

INV

ER

TE

CP

OW

ER

SO

UR

CE

S

1940

5

1-

25-9

1

K86

7 PL

UG

TO

LN

-25

- CO

NN

ECTI

ON

DIA

GR

AM

F-4DIAGRAMSF-4

V350-PRO (CE)

N.A

. W

EL

DIN

G C

AB

LE

MU

ST

BE

SIZ

ED

FO

R C

UR

RE

NT

AN

D D

UT

Y C

YC

LE

OF

AP

PL

ICA

TIO

N.

N.B

. D

IAG

RA

M S

HO

WS

EL

EC

TR

OD

E P

OS

ITIV

E.

TO

CH

AN

GE

PO

LA

RIT

Y,

TU

RN

PO

WE

R "

OF

F",

RE

VE

RS

E E

LE

CT

RO

DE

AN

D W

OR

K C

AB

LE

AT

PO

WE

R S

OU

RC

E.

N.C

. I

NS

UL

AT

E E

AC

H U

NU

SE

D L

EA

D I

ND

IVID

UA

LL

Y.

TO

WO

RK

- +

14

PIN

AM

PH

EN

OL

N.C

.

76

82

K8

67

UN

IVE

RS

AL

AD

AP

TE

R P

LU

G

81

SP

AR

E

24 41

42 31

32

GN

D2

1

77

75

RE

MO

TE

OU

TP

UT

CO

NT

RO

L

NO

T U

SE

D O

N I

NV

ER

TE

C

CO

NN

EC

T T

OG

ET

HE

R F

OR

WE

LD

ING

OU

TP

UT

24

VA

C /

5.5

AM

P

24

VA

C /

5.5

AM

P

42

VA

C /

5.5

AM

P

11

5 V

AC

/ 2

AM

P

INV

ER

TE

C F

RA

ME

CO

NN

EC

TIO

N

N.D

.

N.D

. F

OR

WIR

E F

EE

DE

RS

TH

AT

RE

TU

RN

A S

IGN

AL

FO

R W

EL

DIN

G O

UT

PU

T,

US

E I

SO

LA

TIO

N

R

EL

AY

TO

CL

OS

E L

EA

DS

2 &

4.

2 4

TO

K8

67

EL

EC

TR

OD

E C

AB

LE

WIR

E F

EE

DE

R V

OL

TM

ET

ER

CO

NN

EC

TIO

NC

ON

NE

CT

S T

O (

WO

RK

TE

RM

INA

L)

OF

IN

VE

RT

EC

TO

WIR

E F

EE

DE

R

10

K

MIN

.

Onl

y qu

alifi

ed p

erso

ns s

houl

d in

stal

l, us

e or

serv

ice

this

mac

hine

.

usin

g th

e di

scon

nect

sw

itch

at t

he f

use

box

WARN

INGTu

rn o

ff in

put

pow

er t

o th

e W

eldi

ng P

ower

Sou

rce

Befo

re c

onne

ctin

g th

e w

ire

feed

er.

ELEC

TRIC

SHOC

K

CAN

KILL

INV

ER

TE

CP

OW

ER

SO

UR

CE

WIT

H 1

15

VA

CA

UX

ILIA

RY

PO

WE

R

S

2498

5

3

-1-0

0

K86

7 U

NIV

ERSA

L A

DA

PTER

/ IN

VER

TEC

- C

ON

NEC

TIO

N D

IAG

RA

M

F-5DIAGRAMSF-5

V350-PRO (CE)

Onl

y qu

alifi

ed p

erso

ns s

houl

d in

stal

l, us

e or

serv

ice

this

mac

hine

.

usin

g th

e di

scon

nect

sw

itch

at t

he f

use

box

WARN

INGTu

rn o

ff in

put

pow

er t

o th

e W

eldi

ng P

ower

Sou

rce

Befo

re c

onne

ctin

g th

e w

ire

feed

er.

ELEC

TRIC

SHOC

K

CAN

KILL

N.A

. W

EL

DIN

G C

AB

LE

MU

ST

BE

SIZ

ED

FO

R C

UR

RE

NT

AN

D D

UT

Y C

YC

LE

OF

AP

PL

ICA

TIO

N.

N.B

. D

IAG

RA

M S

HO

WS

EL

EC

TR

OD

E P

OS

ITIV

E.

TO

CH

AN

GE

PO

LA

RIT

Y,

TU

RN

PO

WE

R "

OF

F",

RE

VE

RS

E E

LE

CT

RO

DE

AN

D W

OR

K C

AB

LE

AT

PO

WE

R S

OU

RC

E.

TO

WO

RK

- +

14

PIN

AM

PH

EN

OL

EL

EC

TR

OD

E C

AB

LE

TO

LN

-25

LN

-25

WIT

HK

43

1 O

PT

ION

K4

32

RE

MO

TE

CO

NT

RO

L C

AB

LE

6 P

INA

MP

HE

NO

L

N.C

. F

OR

IN

VE

RT

EC

S W

ITH

6 P

IN A

MP

HE

NO

L,

K4

32

CA

BL

E C

AN

BE

CO

NN

EC

TE

D D

IRE

CT

LY

.

K8

76

AD

AP

TE

R

INV

ER

TE

CP

OW

ER

SO

UR

CE

S

1989

9

1-

25-9

1

K87

6 A

DA

PTER

TO

LN

-25

- CO

NN

ECTI

ON

DIA

GR

AM

F-6DIAGRAMSF-6

V350-PRO (CE)

Onl

y qu

alifi

ed p

erso

ns s

houl

d in

stal

l, us

e or

serv

ice

this

mac

hine

.

usin

g th

e di

scon

nect

sw

itch

at t

he f

use

box

WARN

INGTu

rn o

ff in

put

pow

er t

o th

e W

eldi

ng P

ower

Sou

rce

Befo

re c

onne

ctin

g th

e w

ire

feed

er.

ELEC

TRIC

SHOC

K

CAN

KILL

N.A

. W

EL

DIN

G C

AB

LE

MU

ST

BE

SIZ

ED

FO

R C

UR

RE

NT

AN

D D

UT

Y C

YC

LE

OF

AP

PL

ICA

TIO

N.

N.B

. D

IAG

RA

M S

HO

WS

EL

EC

TR

OD

E P

OS

ITIV

E.

TO

CH

AN

GE

PO

LA

RIT

Y,

TU

RN

PO

WE

R "

OF

F",

RE

VE

RS

E E

LE

CT

RO

DE

AN

D W

OR

K C

AB

LE

AT

PO

WE

R S

OU

RC

E.

EL

EC

TR

OD

E C

AB

LE

TO

LN

-7

TO

WO

RK

- +

14

PIN

AM

PH

EN

OL

LN

-7C

ON

TR

OL

BO

X

PO

WE

R S

OU

RC

E

INV

ER

TE

C

K8

64

K4

80

-7 I

NP

UT

CA

BL

E

14

PIN

AM

PH

EN

OL

K8

57

RE

MO

TE

CO

NT

RO

L

K9

63

HA

ND

AM

PT

RO

L

K8

70

FO

OT

AM

PT

RO

L

N.C

. K

48

0-7

IN

PU

T C

AB

LE

CA

N B

E C

ON

NE

CT

ED

DIR

EC

TL

Y I

F R

EM

OT

E C

ON

TR

OL

IS

NO

T R

EQ

UIR

ED

.

6 P

INA

MP

HE

NO

L

AD

AP

TE

R

OR

OR

N.D

. K

86

4 A

DA

PT

ER

CA

NN

OT

BE

US

ED

WIT

H A

N L

N-2

5.

WIT

H 1

15

VA

C

AU

XIL

IAR

Y P

OW

ER

S

1990

1

4-

19-9

6D

K86

4 A

DA

PTER

TO

LN

-7 &

REM

OTE

CO

NTR

OL

- CO

NN

ECTI

ON

DIA

GR

AM

F-7DIAGRAMSF-7

V350-PRO (CE)

NO

TE

: T

his

dia

gra

m is

fo

r re

fere

nce

onl

y.

It m

ay n

ot

be

accu

rate

fo

r al

l mac

hine

s co

vere

d b

y th

is m

anua

l. T

he s

pec

ific

dia

gra

m f

or

a p

artic

ular

co

de

is p

aste

d in

sid

eth

e m

achi

ne o

n o

ne o

f th

e en

clo

sure

pan

els.

If

the

dia

gra

m is

ille

gib

le, w

rite

to

the

Ser

vice

Dep

artm

ent

for

a re

pla

cem

ent.

Giv

e th

e eq

uip

men

t co

de

num

ber

..

FAN

FRONTOF MACHINE

MAIN

XFMR

205

201

H3H2

REC

ONNE

CT H5H4

NOTE

S:N.

A. 1

. FOR

MAC

HINE

S W

ITH R

ED, B

LACK

AND

WHI

TE P

OWER

COR

DS

FO

R SI

NGLE

PHA

SE IN

PUT:

CON

NECT

GRE

EN LE

AD TO

GRO

UND

PER

NATIO

NAL E

LECT

RICA

L COD

E.

C

ONNE

CT B

LACK

AND

WHI

TE LE

ADS

TO S

UPPL

Y CI

RCUI

T.

W

RAP

RED

LEAD

WITH

TAPE

TO P

ROVI

DE 60

0V. IN

SULA

TION.

FOR

THRE

E PH

ASE

INPU

T: CO

NNEC

T GR

EEN

LEAD

TO G

ROUN

D PE

R NA

TIONA

L ELE

CTRI

C CO

DE.

CON

NECT

BLA

CK, R

ED &

WHI

TE LE

ADS

TO S

UPPL

Y CI

RCUI

T.

FAN

X10

X3

X20X2

3

26

N.C.

PLAC

E "A

" LEA

D ON

APP

ROPR

IATE

CON

NECT

ION

FOR

INPU

T VOL

TAGE

.

CON

NECT

ION

SHOW

N IS

FOR

550-

575V

OPE

RATIO

N. (C

E MO

DELS

ONL

Y GO

TO

440V

AC.)

A

LEFT

SID

E OF

MAC

HINE

204

AA

208

B

G37

07

WIR

ING

DIAG

RAM

INVE

RTEC

V35

0-PRO

(CE)

REAROF MACHINE

X30

X40

X4

X 1

11-

2000

C

SEC

BOOST

RIGH

T SID

E OF

MAC

HINE

7

N.B.

SIN

CE C

OMPO

NENT

S OR

CIR

CUITR

Y OF

A P

RINT

ED C

IRCU

IT BO

ARD

MAY

CHAN

GE W

ITHOU

T AF

FECT

ING

T

HE IN

TERC

HANG

EABI

LITY

OF A

COM

PLET

E BO

ARD,

THIS

DIA

GRAM

MAY

NOT

SHO

W TH

E EX

ACT

C

OMPO

NENT

S OR

CIR

CUIT

RY H

AVIN

G A

COMM

ON C

ODE

NUMB

ER.

206

( 380

-575

VAC

POSI

TION

)

207A

276

277 275

S T A T U S

R510

K/2W

POT

CONT

ROL

277

275

13

24

D I S P L A Y

510

16

49 8

3 27

M O D E

C O N T R O L

276

R(B) B

A

G(G/

Y)W

CB1

W(N

)V

C

B(U)

U23

4

1

15

J4J3

J5J6J7J8J9

J10A

J10B

403402401

408

405

410411412

407

72

38

94

61

10511

12234

150

250

3_+

1020

1002

H1

B

TP1

TP3

A

A

TP2 C

20520

620

3

208

+

201

204 20

220

732

00/30

0

C2,C

4

xxxxxxx

209

SWITC

H

207

209

207A

203

202

H657

5V550-

460V440-

230V220-

380-

415V

208V

200-

H5H6

H2H3H4

AUX

ILIAR

Y

H1

XFMR

7 238

9

46 15

10111213141516

60960

261

1

607

901

903

804

903

723

894

61

105

2

23

41

57

89

10

23 16 5

478

802

806

801

Y = Y

ELLO

W

W =

WHI

TE

N = B

ROW

NU

= BLU

E

R = R

EDG

= GRE

ENB

= BLA

CKCO

LOR

CODE

:

73

894

61

105

BRID

GEIN

PUT

2A

_+A B

E FC

D

_

901

ELEC

TRIC

AL S

YMBO

LS P

ER E

1537

PRI

MARY

PRI-IN

PRI-OUT

PRI-OUT

PRI-IN

SEC BO

OST

OUTP

UTRE

CTIFI

ER

CURR

ENT

TRAN

SDUC

ER

502

505

L2RE

ACTO

R

CHOK

E

REAC

TOR

L1

INPU

TPE

RN.

A.

}

406

61260

8

J34

J31

J311

J37

J2J1

EF

AB

CD

802804801806 4 3

21

+

(REA

R VI

EW)

2A 4A

32

76A

21

R E M O T E1

7

410 9

3 28

J33

510

16

49 8

3 27

J331

742V

54124 24V

1642

COM1774A 754

612 11

5

551

553

552

554

115V

P56

P52

5

42

7577

76

21

903A901A

554

553

+

TP4 TP

5

405

407

66 654

13

2

121110987

651 432

406 401

402

403

6541 32

408

410

412

411

J43

J41

J42 P O W E R

GAS

SOLE

NOID

115V

WIR

E FE

EDER

REMO

TE

16 1571

571

6

615

616

615

607 611

612

3200

/300

C1,C

3

+

CONT

ROL

RECT

IFIER

54

65

2400

/80

+C5 41

A ~

~

66 -

+

6 PIN

REMO

TE(R

EAR

VIEW

)

61060

5

41A 6

100 A

CIR

CUIT

BREA

KER

SPI F

L EX

CIRC

U IT

SPI F

L EXC

I RCU

ITSP

I FL E

XCI

RCUI

TSP

I FL E

XCI

RCUI

T

N.C.

(REA

R VI

EW )

1

31532 11

77A

GND

31 75A

77B

2B 4B

76B

AB

C

JK

LD

EM

I HG

FN

J21

3 1

J20 1 2 3

65

4 260

8

I

605

616

610

X10

X30

66B

65B

J90

901B 903B

R1S1

216 12

CONN

ECTO

R CA

VITY

NUM

BERI

NG S

EQUE

NCE

(VIE

WED

FRO

M CO

MPON

ENT S

IDE

OF B

OARD

)J43,

J331

1 7

J8,

J20,J

214 8

1 5

J9, J

42, P

53 3 6

1 4

J2,J5

,J11,

J22,

J41,

J311

, P55

21

43

J31,J

33,

J34,J

37

6

5 10

1J1

,J6,J7

, P52

8 16

1 9

CB2

S N U B B E RX1

0

X2X4

X20

X40

X30

75B54 1

28V

432

438

431

432

438

431

CB2 53

232P5

5 2155

1 552

43

21B

2 76 76A

77A

2A

75A

1 2210

1010

01

6

BASE

CASE

FRO

NTPR

OTEC

TIVE

BON

DING

CIR

CUIT

GND

42 75B

77B

2B 4B

21B

76B

AB

C

JK

LD

EM

I HG

FN41 24

CB1 54

14141

B41

B

24/42

V W

IRE

FEED

ERRE

MOTE

J11

715

716

78 6 5

1020

1010

1001

1002

FAN

41

23

FAN

J22 COM2

115VFAN

6A2A

COM2

1001

,100

2,10

10,1

020

21,21

B,2A

,4A,

75A,

76A,

77A

SNB

6

7 84

609

602

503

xxxxxxx

506

505

506

J10A

,J1

0B

COM2

A

ON "C

E" M

ODEL

S. N

.D. I

NPUT

POW

ER LI

NE FI

LTER

IS P

RESE

NT O

NLY

N.E

. ON

"CE"

MOD

ELS,

MOV

's AR

E IN

THE

INPU

T POW

ER LI

NE FI

LTER

.

N.D.

N.E.

LEGE

ND

ALL M

ACHI

NES

OP

TION

CO

MPON

ENT O

UTLIN

E

GND

IN P

ARAN

THES

YS C

OLOR

SFO

R CE

MAC

HINE

S

CONT

ROL

MODE

STAT

USDI

SPLA

YRE

MOTE

CONT

ROL

MODE

STAT

USDI

SPLA

Y

SPI F

LEX

CIRC

UIT C

ONNE

CTIO

N DE

TAIL

FOR

MACH

INES

WIT

HOUT

REM

OTE

BOAR

D

FOR

MACH

INES

WIT

H RE

MOTE

BOA

RD

2. FO

R MA

CHIN

ES W

ITH B

ROW

N, B

LACK

AND

BLU

E PO

WER

COR

DS

F

OR S

INGL

E PH

ASE

INPU

T: C

ONNE

CT G

REEN

/YEL

LOW

LEAD

TO G

ROUN

D PE

R NA

TIONA

L ELE

CTRI

CAL C

ODE.

CON

NECT

BLU

E AN

D BR

OWN

LEAD

S TO

SUP

PLY

CIRC

UIT.

WRA

P BL

ACK

LEAD

WITH

TAPE

TO P

ROVI

DE 60

0V. IN

SULA

TION.

FOR

THR

EE P

HASE

INPU

T: CO

NNEC

T GR

EEN/

YELL

OW G

ROUN

D PE

R NA

TIONA

L ELE

CTRI

C CO

DE.

CON

NECT

BLU

E, B

LACK

& B

ROW

N LE

ADS

TO S

UPPL

Y CI

RCUI

T.

F-8DIAGRAMSF-8

V350-PRO (CE)

1 4.7

9

12.4

4

3.44

21.6

0

27.8

2

5.50

10.0

0

MO

UN

TIN

G H

OLE

LO

CAT

ION

S

M19

527

13.1

0

1/4-

20 N

UT

(4 P

LACE

S)

NO

TE:

MO

UN

TIN

G S

CR

EWS

CA

8/00

N N

OT

PRO

TRU

DE

MO

RE

THAN

0.

5 IN

CH

ES IN

SID

E TH

E M

ACH

INE.

11.8

4

3.50

DIM

ENSI

ON

PR

INT

Now Available...12th EditionThe Procedure Handbook of Arc Welding

With over 500,000 copies of previous editions publishedsince 1933, the Procedure Handbook is considered by many to be the “Bible” of the arc welding industry.

This printing wil l go fast so don ’t delay. Place your order now using the coupon below.

The hardbound book contains over 750 pages of weldinginformation, techniques and procedures. Much of this material has never been included in any other book.

A must for al l welders, supervisors, engineers anddesigners. Many welding instructors will want to use the bookas a reference for all students by taking advantage of the lowquantity discount prices which include shipping by4th class parcel post.

$15.00 postage paid U.S.A. Mainland

How To Read Shop Drawings

The book contains the latest information and applicationdata on the American Welding Society Standard WeldingSymbols. Detailed discussion tells how engineers anddraftsmen use the “short-cut” language of symbols to passon assembly and welding information to shop personnel.

Practical exercises and examples develop the reader’s abilityto visualize mechanically drawn objects as they will appearin their assembled form.

187 pages with more than 100 illustrations. Size 8-1/2” x 11”Durable, cloth-covered board binding.


New Lessons in Arc WeldingLessons, simply written, cover manipulatory techniques;

machine and electrode characteristics; related subjects,such as distortion; and supplemental information on arcwelding applications, speeds and costs. Practice materials,exercises, questions and answers are suggested for each lesson.

528 pages, well illustrated, 6” x 9” size, bound in simulated,gold embossed leather.


Need Welding Training?The Lincoln Electric Company operates the oldest and

most respected Arc Welding School in the United States at itscorporate headquarters in Cleveland, Ohio. Over 100,000 stu-dents have graduated. Tuit ion is low and the training is “hands on”

For details write: Lincoln Welding School22801 St. Clair Ave. Cleveland, Ohio 44117-1199.

and ask for bulletin ED-80 or call 216-383-2259 and ask for theWelding School Registrar.

Lincoln Welding SchoolBASIC COURSE $700.00

5 weeks of fundamentalsThere is a 10% discount on all orders of $50.00 or more for shipment at one time to one location.Orders of $50 or less before discount or orders outside of North America must be prepaid with charge, check or money order in U.S. Funds Only.Prices include shipment by 4 thClass Book Rate for U.S.A. Mainland Only. Please allow up to 4 weeks for delivery.UPS Shipping for North America Only. All prepaid orders that request UPS shipment please add:

$5.00 For order value up to $49.99$10.00 For order value between $50.00 & $99.99$15.00 For order value between $100.00 & $149.00

For North America invoiced orders over $50.00 & credit card orders, if UPS is requested, it will be invoiced or charged to you at cost.Outside U.S.A. Mainland order must be prepaid in U.S. Funds. Please add $2.00 per book for surface mail or $15.00 per book for air parcel post shipment.METHOD OF PAYMENT: (Sorry, No C.O.D. Orders)

CHECK ONE:Name: _______________________________________________

Please Invoice (only if order is over $50.00)Address: _______________________________________________

Check or Money Order Enclosed, U.S. Funds only _______________________________________________

Credit Card - Telephone: _______________________________________________

Signature as it appears on Charge Card:Account No. |_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_|_| Exp Date |_|_| |_|_| ______________________Month Year

USE THIS FORM TO ORDER: Order from: BOOK DIVISION, The Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199BOOKS OR FREE INFORMATIVE CATALOGS Telephone: 216-383-2211 or, for fastest service, FAX this completed form to: 216-361-5901.

Lincoln Welding School Titles: Price Code Quantity Cost(ED-80) New Lessons in Arc Welding $5.00 L

Seminar Information Procedure Handbook “Twelfth Edition” $15.00 PH(ED-45) How to Read Shop Drawings $4.50 H

Educational Video Information Incentive Management $5.00 IM(ED-93) A New Approach to Industrial Economics $5.00 NA

James F. Lincoln Arc Welding The American Century of John C. Lincoln $5.00 ACFoundation Book Information Welding Preheat Calculator $3.00 WC-8

(JFLF-515) Pipe Welding Charts $4.50 ED-89SUB TOTAL

Additional Shipping Costs if anyTOTAL COST

MasterCard

VISA ®

AMERICAN EXPRESS

MasterCardMasterCard®

AMERICAN EXPRESS

WARNING

AVISO DEPRECAUCION

ATTENTION

WARNUNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BEUSED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.

SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOSCONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.

LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS AETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.

LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.

● Do not touch electrically live parts orelectrode with skin or wet clothing.

● Insulate yourself from work andground.

● No toque las partes o los electrodosbajo carga con la piel o ropa moja-da.

● Aislese del trabajo y de la tierra.

● Ne laissez ni la peau ni des vête-ments mouillés entrer en contactavec des pièces sous tension.

● Isolez-vous du travail et de la terre.

● Berühren Sie keine stromführendenTeile oder Elektroden mit IhremKörper oder feuchter Kleidung!

● Isolieren Sie sich von denElektroden und dem Erdboden!

● Não toque partes elétricas e elec-trodos com a pele ou roupa molha-da.

● Isole-se da peça e terra.

● Keep flammable materials away.

● Mantenga el material combustiblefuera del área de trabajo.

● Gardez à l’écart de tout matérielinflammable.

● Entfernen Sie brennbarres Material!

● Mantenha inflamáveis bem guarda-dos.

● Wear eye, ear and body protection.

● Protéjase los ojos, los oídos y elcuerpo.

● Protégez vos yeux, vos oreilles etvotre corps.

● Tragen Sie Augen-, Ohren- und Kör-perschutz!

● Use proteção para a vista, ouvido ecorpo.

WARNING

AVISO DEPRECAUCION

ATTENTION

WARNUNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA ASPRÁTICAS DE SEGURANÇA DO EMPREGADOR.

● Keep your head out of fumes.● Use ventilation or exhaust to

remove fumes from breathing zone.

● Los humos fuera de la zona de res-piración.

● Mantenga la cabeza fuera de loshumos. Utilice ventilación oaspiración para gases.

● Gardez la tête à l’écart des fumées.● Utilisez un ventilateur ou un aspira-

teur pour ôter les fumées des zonesde travail.

● Vermeiden Sie das Einatmen vonSchweibrauch!

● Sorgen Sie für gute Be- undEntlüftung des Arbeitsplatzes!

● Mantenha seu rosto da fumaça.● Use ventilação e exhaustão para

remover fumo da zona respiratória.

● Turn power off before servicing.

● Desconectar el cable de ali-mentación de poder de la máquinaantes de iniciar cualquier servicio.

● Débranchez le courant avant l’entre-tien.

● Strom vor Wartungsarbeitenabschalten! (Netzstrom völlig öff-nen; Maschine anhalten!)

● Não opere com as tampas removidas.● Desligue a corrente antes de fazer

serviço.● Não toque as partes elétricas nuas.

● Do not operate with panel open orguards off.

● No operar con panel abierto oguardas quitadas.

● N’opérez pas avec les panneauxouverts ou avec les dispositifs deprotection enlevés.

● Anlage nie ohne Schutzgehäuseoder Innenschutzverkleidung inBetrieb setzen!

● Mantenha-se afastado das partesmoventes.

● Não opere com os paineis abertosou guardas removidas.

• Sales and Service through Subsidiaries and Distributors Worldwide •Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

IM708 INVERTEC V350-PRO (CE) January, 2001€¦ · ipisc i ng li, e d am n eli d a m non m umm y bh...

Documents

Transcript of IM708 INVERTEC V350-PRO (CE) January, 2001€¦ · ipisc i ng li, e d am n eli d a m non m umm y bh...