Illustrated Parts Breakdown Manual EZ LOADER Model · PDF fileEZ LOADER Model EZ18 ... Tail...

Preliminary Manual December 7, 2007

Illustrated Parts Breakdown Manual

EZ LOADER

Model EZ18 (Pre-06/07)

Xtreme Manufacturing 1415 West Bonanza Road

Las Vegas, NV 89106 (702) 858-2404

www.xtrememanufacturing.com

Copyr ight © 2007 By Xt reme Manufactur ing

Xtreme Manufacturing EZ18 Easy Loader

December 7, 2007 Preliminary Manual A

List of Effective Pages

This manual consists of 70 pages as listed below:

Outside title page Inside title page Pages A through D Pages i through iv Pages 1-1 through 1-2 Pages 2-1 through 2-10 Pages 3-1 through 3-8 Pages 4-1 through 4-14 Pages 5-1 through 5-10 Index 1 through Index 12 Contact page Warranty 1 through Warranty 2 Back cover


December 7, 2007 Preliminary Manual B

Service Bulletins

The following service bulletins have been incorporated in this manual:

Title Bulletin No. Comments


December 7, 2007 Preliminary Manual C

Design Change Notices

The following design change notices have been incorporated in this manual:

Title Design Change Notice No. Comments


December 7, 2007 Preliminary Manual D

THIS PAGE INTENTIONALLY LEFT BLANK


Preliminary Manual i

Table of Contents

Chap./Par. Title Page

List of Effective Pages........................................................................................................................ A

Service Bulletins ................................................................................................................................. B

Design Change Notices ...................................................................................................................... C

Alphabetical List of Parts Breakdowns ............................................................................................ ii

Numerical List of Parts Breakdowns ................................................................................................ v

Section 1 – General Information ...................................................................................................... 1-1

Section 2 – Chassis .......................................................................................................................... 2-1

Section 3 – Decals............................................................................................................................. 3-1

Section 4 – Hydraulic System .......................................................................................................... 4-1

Section 5 – Electrical System .......................................................................................................... 5-1

Numerical and Alphabetical Indexes .............................................................................................. Index 1


December 7, 2007 Preliminary Manual ii

Alphabetical List of Parts Breakdowns

Title Figure No. Page No.

Backup Light Assembly......................................... 5-2...............................................................................5-4 Check Valve Assembly ......................................... 4-5.............................................................................4-10 Control Valve Assembly ........................................ 4-3...............................................................................4-6 Decals ................................................................... 3-1...............................................................................3-2 Bed Assembly ....................................................... 2-1...............................................................................2-2 Hose and Fitting Kit............................................... 4-6.............................................................................4-12 Hydraulic Filter Assembly...................................... 4-2...............................................................................4-4 Hydraulic Tank Assembly...................................... 4-1...............................................................................4-2 Junction Assembly ................................................ 4-4...............................................................................4-8 Marker Lamp Assembly, Red................................ 5-3...............................................................................5-6 Marker Lamp Assembly, Yellow............................ 5-4...............................................................................5-8 Tail Light Assembly .............................................. 5-1...............................................................................5-2 Toolbox Assembly................................................. 2-3...............................................................................2-8 Winch Assembly.................................................... 2-2...............................................................................2-6


December 7, 2007 Preliminary Manual iii

Numerical List of Parts Breakdowns

Figure No. Title Page No.

2-1 ............. Bed Assembly.........................................................................................................................2-2 2-2 ............. Winch Assembly .....................................................................................................................2-6 2-3 ............. Toolbox Assembly ..................................................................................................................2-8

3-1 ............. Decals.....................................................................................................................................3-2

4-1 ............. Hydraulic Tank Assembly .......................................................................................................4-2 4-2 ............. Hydraulic Filter Assembly .......................................................................................................4-4 4-3 ............. Control Valve Assembly .........................................................................................................4-6 4-4 ............. Junction Assembly..................................................................................................................4-8 4-5 ............. Check Valve Assembly.........................................................................................................4-10 4-6 ............. Hose and Fitting Kit ..............................................................................................................4-12

5-1 ............. Tail Light Assembly ................................................................................................................5-2 5-2 ............. Backup Light Assembly ..........................................................................................................5-4 5-3 ............. Marker Lamp Assembly, Red .................................................................................................5-6 5-4 ............. Marker Lamp Assembly, Yellow .............................................................................................5-8


December 7, 2007 Preliminary Manual iv



December 7, 2007 Preliminary Manual 1-1

Section 1

General Information

Table 1-1. Abbreviations & Acronyms

Term Meaning

A Amperes

ASTM American Society for Testing and Materials

AWG American Wire Gauge

BHC Button head cap

BKDN Breakdown

DIA Diameter

DPDT Double-pole, double-throw

FSHC Flat socket head cap

FTG Fittings

HHC Hex head cap

ID Inside diameter

LG Long

MM Millimeter

NHA Next higher assembly

NPT National pipe thread

OD Outside diameter

OHM Oval head machine

PHM Pan head machine

PWH Pan washer head

QD Quick-Disconnect

REF Reference

REG Regular

SAE Society of Automotive Engineers

SBHC Socket button head cap

SHC Socket head cap

SHS Socket head shoulder



Term Meaning

SPDT Single-throw, double-pole

SPST Single-pole, single-throw

STR Straight

THD Thread

UNC Unified National Coarse

UNF Unified National Fine

V Volts



Section 2

Chassis



2

1

3

4

5

Figure 2-1. Bed Assembly (Sheet 1 of 2)



Figure 2-1. Bed Assembly (Sheet 2 of 2)



Table 2-1. Bed Assembly

Figure & Item No. Part No. Description Quantity Use On

– 50150-000 Bed assembly – –

2-1-1 50030-000 Hydraulic tank assembly 1 –

2-1-2 50831-000 Control valve assembly 1 –

2-1-3 50636-000 Winch assembly 1 –

2-1-4 50641-000 Tool box assembly 1 –

2-1-5 50183-000 PTO pump 1 –

2-1-6 50136-000 Left dove tail cylinder 1 –

2-1-7 50137-000 Right dove tail cylinder 1 –

2-1-8 50062-000 Latch hanger plate 2 –

2-1-9 50093-000 Tail idler weldment 1 –

2-1-10 50107-000 Right dove tail cylinder mount weldment

1 –

2-1-11 50108-000 Left dove tail cylinder mount weldment

1 –

2-1-12 50123-000 Spacer 2 –

2-1-13 11001-006 3/8” washer 10 –

2-1-14 10002-008 3/8-16 x 1” HHC screw 14 –

2-1-15 50096-000 Dove tail cylinder pin weldment 2 –

2-1-16 50088-000 Dove tail support weldment 1 –

2-1-17 50124-000 Dove tail support bar 2 –

2-1-18 50122-000 Tail idler pin 1 –

2-1-19 50125-000 Tail idler roller 1 –

2-1-20 11202-016 1/4 x 2” roll pin 2 –

2-1-21 50100-000 Tail latch weldment 1 –

2-1-22 50119-000 Tail support tube 1 –

2-1-23 50112-000 Pivot pin 7” 2 –



Table 2-1. Bed Assembly


2-1-24 50104-000 Pivot pin 5” 3 –

2-1-25 50118-000 Retractor bar 2 –

2-1-26 11001-016 Washer 1” SAE flat 8 –

2-1-27 50113-000 Retractor bracket 2 –

2-1-28 50145-000 Flip tail cylinder 1 –

2-1-29 50061-000 Right flip tail cylinder mount 1 –

2-1-30 50060-000 Left flip tail cylinder mount 1 –

2-1-31 50120-000 Lower cylinder pin 1 –

2-1-32 50130-000 Linkage bar 2 –

2-1-33 50155-000 Spacer, short 2 –

2-1-34 10903-020 1 1/4-12 hex jam nut 2 –

Refer to Section 1 for the definition of acronyms and abbreviations used in the Description Column.



Figure 2-2. Winch Assembly



Table 2-2. Winch Assembly


– 50636-000 Winch assembly – –

2-2-1 50635-000 Winch angle weldment 1 –

2-2-2 50146-000 Winch, 9000 lb 1 –

2-2-3 50147-000 Winder, winch level 1 –

2-2-4 11001-008 Washer 1/2” SAE flat 2 –

2-2-5 10004-018 Screw 1/2-13UNC HHC x 2-1/4” 2 –




Figure 2-3. Toolbox Assembly



Table 2-3. Toolbox Assembly

Figure & Index No. Part No. Description Quantity Use On

– 50641-000 Toolbox assembly – –

2-3-1 50116-001 Toolbox 1 –

2-3-2 50755-000 Toolbox mount angle 2 –

2-3-3 50642-000 Toolbox mount weldment 1 –


Xtreme Manufacturing EZ18


Section 3

Decals



Figure 3-1. Decals (Sheet 1 of 5)



1

2

3




4

5

6




7

8




9




Table 3-1. Decals


3-1-1 18042-000 Decal, Xtreme Manufacturing 2 –

3-1-2 18108-000 Decal, Danger, Pinch Point 8 –

3-1-3 18112-000 Decal, Controls 1 –

3-1-4 18113-000 Decal, E-Z Loader 2 –

3-1-5 18007-999 Decal, Reflective 2 –

3-1-6 18105-000 Decal, Warning, Tail Capacity 2 –

3-1-7 18106-000 Decal, Warning, Bed Capacity 2 –

3-1-8 18107-000 Decal, Caution, Vehicle Information 2 –

3-1-9 18114-000 Decal, Vehicle Identification 1 –



Section 4

Hydraulic System



Figure 4-1. Hydraulic Tank Assembly



Table 4-1. Hydraulic Tank Assembly


– 50030-000 Hydraulic tank assembly – –

4-1-1 50039-000 Weldment, hydraulic tank 1 –

4-1-2 50151-000 Breather cap 3/4” NPT 1 –

4-1-3 50152-000 Fitting STR -12MP-12MJ 1 –

4-1-4 50153-000 Fitting STR -16MP-16MJ 1 –

4-1-5 50157-000 Gauge, 5” sight 1 –




Figure 4-2. Hydraulic Filter Assembly



Table 4-2. Hydraulic Filter Assembly


– 50089-000 Hydraulic filter assembly – –

4-2-1 50134-000 Filter bracket 1 –

4-2-2 50186-000 Filter 1 –

4-2-3 11001-004 Washer 1/4” SAE flat ASTM 2 –

4-2-4 10000-008 Screw 1/4-20UNC HHC x 1” 2 –

4-2-5 50152-000 Fitting STR-12MP-12MJ 2 –




Figure 4-3. Control Valve Assembly



Table 4-3. Control Valve Assembly


– 50831-000 Control valve assembly – –

4-3-1 50184-000 Control valve 1 –

4-3-2 11699-006 Plug hex SOC -08MB 2 –

4-3-3 11699-003 Plug hex SOC -04MB 1 –

4-3-4 11666-007 Fitting elbow 90 -08MBA-06MJ 1 –

4-3-5 11660-001 Fitting STR 04MB-04MJ 5 –

4-3-6 11660-014 Fitting STR 08MB-08MJ 2 –




Figure 4-4. Junction Assembly



Table 4-4. Junction Assembly


– 50828-000 Junction assembly – –

4-4-1 50777-000 Junction mount plate 1 –

4-4-2 50829-000 Check valve assembly 1 –

4-4-3 50470-000 Junction box surface mount 1 –

4-4-4 50471-000 Junction box filler plug 5 –

4-4-5 50473-000 Strain relief 3/4” 3 –

4-4-6 13051-000 Back-up alarm 1 –

4-4-7 11001-006 Washer 3/8” SAE flat 1 –

4-4-8 10900-006 Nut 3/8-16UNC reg hex 1 –

4-4-9 10156-020 Screw 3/8-16UNC FSHC x 2-1/2” 1 –

4-4-10 11001-003 Washer #10 SAE flat 8 –

4-4-11 10253-006 Screw #10-24UNC PHM x 3/4” 4 –

4-4-12 10908-003 Nut #10-24UNC hex lock 4 –

4-4-13 11001-004 Washer 1/4” SAE flat ASTM 4 –

4-4-14 10000-006 Screw 1/4-20UNC HHC x 3/4” 2 –

4-4-15 10900-004 Nut 1/4-20UNC reg hex 2 –




Figure 4-5. Check Valve Assembly



Table 4-5. Check Valve Assembly


– 50829-000 Check valve assembly – –

4-5-1 50830-000 Check valve 1 –

4-5-2 11660-010 Fitting STR -08MB-06MJ 1 –

4-5-3 11702-006 Fitting elbow 90 -06MBA-06MFS 1 –




Figure 4-6. Hose and Fitting Kit



Table 4-6. Hose and Fitting Kit


– 50161-000 Hose and fitting kit – –

4-6-1 50161-001 Valve bank to bed 4 –

4-6-2 50161-002 Valve bank to winch 2 –

4-6-3 50161-003 Rear plate to flip tail 1 –

4-6-4 50161-004 Rear plate to flip tail 1 –

4-6-5 50161-005 Wall to dove tail cylinder 1 –




4-6-9 50161-009 Wall to valve 1 –

4-6-10 50161-010 Pump to valve body 1 –

4-6-11 50161-011 Filter to valve 1 –

4-6-12 50161-012 Filter to tank 1 –

4-6-13 50161-013 Pump to tank 1 –

4-6-14 50161-014 Winch motor 2 –

4-6-15 50161-015 A & B ports directional valve bank 5 –

4-6-16 50161-016 Valve bank outlet to filter 1 –

4-6-17 50161-017 Pump to valve bank inlet 1 –

4-6-18 50161-018 Inlet adapter for pressure gauge 1 –

4-6-19 50161-019 Holding valve block port 1 –

4-6-20 50161-020 Cylinder port 6 –

4-6-21 50161-021 In/outlet for filter 2 –

4-6-22 50161-022 Return to tank from filter 1 –

4-6-23 50161-023 Tank suction to pump 1 –

4-6-24 50161-024 Valve bank to wall dove tail 2 –



Table 4-6. Hose and Fitting Kit


4-6-25 50161-025 Valve bank to wall flip tail 2 –

4-6-26 50161-026 Nut for bulkhead fittings 4 –

4-6-27 50161-027 Pump pressure outlet 1 –

4-6-28 50161-028 Pump suction inlet 1 –

4-6-29 50161-029 Holding valve block port 1 –

4-6-30 50161-030 Valve block to holding valve block 1 –

4-6-31 50161-031 Cap for pressure gage port 1 –




Section 5

Electrical System



Figure 5-1. Tail Light Assembly



Table 5-1. Tail Light Assembly


– 50196-000 Tail light assembly – –

5-1-1 50196-001 Light 1 –

5-1-2 50196-002 Grommet 1 –

5-1-3 50196-003 Plug 1 –




Figure 5-2. Backup Light Assembly



Table 5-2. Backup Light Assembly


– 50197-000 Backup light assembly – –

5-2-1 50197-001 Light 1 –

5-2-2 50196-002 Grommet 1 –

5-2-3 50196-003 Plug 1 –




Figure 5-3. Marker Lamp Assembly, Red



Table 5-3. Marker Lamp Assembly, Red


– 50189-000 Marker lamp assembly, red – –

5-3-1 50190-000 Grommet 1 –

5-3-2 50192-000 Light 1 –

5-3-3 50193-000 Plug 1 –




Figure 5-4. Marker Lamp Assembly, Yellow



Table 5-4. Marker Lamp Assembly, Yellow


– 50189-001 Marker lamp assembly, yellow – –

5-4-1 50190-000 Grommet 1 –

5-4-2 50191-000 Light 1 –

5-4-3 50193-000 Plug 1 –



December 7, 2007 Preliminary Manual Index-1

Numerical and Alphabetical Indexes

Numerical Index of Parts Numbers

Part No. Part Description Fig. & Index No.

10000-006 Screw 1/4-20UNC HHC x 3/4” 4-4-14

10000-008 Screw 1/4-20UNC HHC x 1” 4-2-4

10002-008 3/8-16 x 1” HHC screw 2-1-14

10004-018 Screw 1/2-13UNC HHC x 2-1/4” 2-2-5

10156-020 Screw 3/8-16UNC FSHC x 2-1/2” 4-4-9

10253-006 Screw #10-24UNC PHM x 3/4” 4-4-11

10900-004 Nut 1/4-20UNC reg hex 4-4-15

10900-006 Nut 3/8-16UNC reg hex 4-4-8

10903-020 1 1/4-12 hex jam nut 2-1-34

10908-003 Nut #10-24UNC hex lock 4-4-12

11001-003 Washer #10 SAE flat 4-4-10

11001-004 Washer 1/4” SAE flat ASTM 4-2-3

11001-004 Washer 1/4” SAE flat ASTM 4-4-13

11001-006 3/8” washer 2-1-13

11001-006 Washer 3/8” SAE flat 4-4-7

11001-008 Washer 1/2” SAE flat 2-2-4

11202-016 1/4 x 2” roll pin 2-1-20

11660-001 Fitting STR 04MB-04MJ 4-3-5

11660-010 Fitting STR -08MB-06MJ 4-5-2

11660-014 Fitting STR 08MB-08MJ 4-3-6

11666-007 Fitting elbow 90 -08MBA-06MJ 4-3-4

11699-003 Plug hex SOC -04MB 4-3-3





11699-006 Plug hex SOC -08MB 4-3-2

11702-006 Fitting elbow 90 -06MBA-06MFS 4-5-3

13051-000 Back-up alarm 4-4-6

18007-999 Decal, Reflective 3-1-5

18042-000 Decal, Xtreme Manufacturing 3-1-1

18105-000 Decal, Warning, Tail Capacity 3-1-6

18106-000 Decal, Warning, Bed Capacity 3-1-7

18107-000 Decal, Caution, Vehicle Information 3-1-8

18108-000 Decal, Danger, Pinch Point 3-1-2

18112-000 Decal, Controls 3-1-3

18113-000 Decal, E-Z Loader 3-1-4

18114-000 Decal, Vehicle Identification 3-1-9

50030-000 Hydraulic tank assembly 2-1-1

50030-000 Hydraulic tank assembly –

50039-000 Weldment, hydraulic tank 4-1-1

50060-000 Left flip tail cylinder mount 2-1-30

50061-000 Right flip tail cylinder mount 2-1-29

50062-000 Latch hanger plate 2-1-8

50088-000 Dove tail support weldment 2-1-16

50089-000 Hydraulic filter assembly –

50093-000 Tail idler weldment 2-1-9

50096-000 Dove tail cylinder pin weldment 2-1-15

50100-000 Tail latch weldment 2-1-21

50100-004 Spacer 2-1-26

50104-000 Pivot pin 5” 2-1-24

50107-000 Right dove tail cylinder mount weldment 2-1-10





50108-000 Left dove tail cylinder mount weldment 2-1-11

50112-000 Pivot pin 7” 2-1-23

50113-000 Retractor bracket 2-1-27

50116-001 Toolbox 2-3-1

50118-000 Retractor bar 2-1-25

50119-000 Tail support tube 2-1-22

50120-000 Lower cylinder pin 2-1-31

50122-000 Tail idler pin 2-1-18

50123-000 Spacer 2-1-12

50124-000 Dove tail support bar 2-1-17

50125-000 Tail idler roller 2-1-19

50130-000 Linkage bar 2-1-32

50134-000 Filter bracket 4-2-1

50136-000 Left dove tail cylinder 2-1-6

50137-000 Right dove tail cylinder 2-1-7

50145-000 Flip tail cylinder 2-1-28

50146-000 Winch, 9000 lb 2-2-2

50147-000 Winder, winch level 2-2-3

50150-000 Bed assembly –

50151-000 Breather cap 3/4” NPT 4-1-2

50152-000 Fitting STR -12MP-12MJ 4-1-3

50152-000 Fitting STR-12MP-12MJ 4-2-5

50153-000 Fitting STR -16MP-16MJ 4-1-4

50155-000 Spacer, short 2-1-33

50157-000 Gauge, 5” sight 4-1-5

50161-000 Hose and fitting kit –





50161-001 Valve bank to bed 4-6-1

50161-002 Valve bank to winch 4-6-2

50161-003 Rear plate to flip tail 4-6-3

50161-004 Rear plate to flip tail 4-6-4

50161-005 Wall to dove tail cylinder 4-6-5




50161-009 Wall to valve 4-6-9

50161-010 Pump to valve body 4-6-10

50161-011 Filter to valve 4-6-11

50161-012 Filter to tank 4-6-12

50161-013 Pump to tank 4-6-13

50161-014 Winch motor 4-6-14

50161-015 A & B ports directional valve bank 4-6-15

50161-016 Valve bank outlet to filter 4-6-16

50161-017 Pump to valve bank inlet 4-6-17

50161-018 Inlet adapter for pressure gauge 4-6-18

50161-019 Holding valve block port 4-6-19

50161-020 Cylinder port 4-6-20

50161-021 In/outlet for filter 4-6-21

50161-022 Return to tank from filter 4-6-22

50161-023 Tank suction to pump 4-6-23

50161-024 Valve bank to wall dove tail 4-6-24

50161-025 Valve bank to wall flip tail 4-6-25

50161-026 Nut for bulkhead fittings 4-6-26





50161-027 Pump pressure outlet 4-6-27

50161-028 Pump suction inlet 4-6-28

50161-029 Holding valve block port 4-6-29

50161-030 Valve block to holding valve block 4-6-30

50161-031 Cap for pressure gage port 4-6-31

50183-000 PTO pump 2-1-5

50184-000 Control valve 4-3-1

50186-000 Filter 4-2-2

50189-000 Marker lamp assembly, red –

50189-001 Marker lamp assembly, yellow –

50190-000 Grommet 5-3-1

50190-000 Grommet 5-4-1

50191-000 Light 5-4-2

50192-000 Light 5-3-2

50193-000 Plug 5-3-3

50193-000 Plug 5-4-3

50196-000 Tail light assembly –

50196-001 Light 5-1-1

50196-002 Grommet 5-1-2

50196-002 Grommet 5-2-2

50196-003 Plug 5-1-3

50196-003 Plug 5-2-3

50197-000 Backup light assembly –

50197-001 Light 5-2-1

50470-000 Junction box surface mount 4-4-3

50471-000 Junction box filler plug 4-4-4





50473-000 Strain relief 3/4” 4-4-5

50635-000 Winch angle weldment 2-2-1

50636-000 Winch assembly 2-1-3

50636-000 Winch assembly –

50641-000 Tool box assembly 2-1-4

50641-000 Toolbox assembly –

50642-000 Toolbox mount weldment 2-3-3

50755-000 Toolbox mount angle 2-3-2

50777-000 Junction mount plate 4-4-1

50828-000 Junction assembly –

50829-000 Check valve assembly 4-4-2

50829-000 Check valve assembly –

50830-000 Check valve 4-5-1

50831-000 Control valve assembly 2-1-2

50831-000 Control valve assembly –



Alphabetical Index of Part Descriptions

Part Description Part No. Fig. & Index No.

1 1/4-12 hex jam nut 10903-020 2-1-34

1/4 x 2” roll pin 11202-016 2-1-20

3/8” washer 11001-006 2-1-13

3/8-16 x 1” HHC screw 10002-008 2-1-14

A & B ports directional valve bank 50161-015 4-6-15

Back-up alarm 13051-000 4-4-6

Backup light assembly 50197-000 –

Bed assembly 50150-000 –

Breather cap 3/4” NPT 50151-000 4-1-2

Cap for pressure gage port 50161-031 4-6-31

Check valve 50830-000 4-5-1

Check valve assembly 50829-000 4-4-2

Check valve assembly 50829-000 –

Control valve 50184-000 4-3-1

Control valve assembly 50831-000 2-1-2

Control valve assembly 50831-000 –

Cylinder port 50161-020 4-6-20

Decal, Caution, Vehicle Information 18107-000 3-1-8

Decal, Controls 18112-000 3-1-3

Decal, Danger, Pinch Point 18108-000 3-1-2

Decal, E-Z Loader 18113-000 3-1-4

Decal, Reflective 18007-999 3-1-5

Decal, Vehicle Identification 18114-000 3-1-9

Decal, Warning, Bed Capacity 18106-000 3-1-7

Decal, Warning, Tail Capacity 18105-000 3-1-6





Decal, Xtreme Manufacturing 18042-000 3-1-1

Dove tail cylinder pin weldment 50096-000 2-1-15

Dove tail support bar 50124-000 2-1-17

Dove tail support weldment 50088-000 2-1-16

Filter 50186-000 4-2-2

Filter bracket 50134-000 4-2-1

Filter to tank 50161-012 4-6-12

Filter to valve 50161-011 4-6-11

Fitting elbow 90 -06MBA-06MFS 11702-006 4-5-3

Fitting elbow 90 -08MBA-06MJ 11666-007 4-3-4

Fitting STR 04MB-04MJ 11660-001 4-3-5

Fitting STR -08MB-06MJ 11660-010 4-5-2

Fitting STR 08MB-08MJ 11660-014 4-3-6

Fitting STR -12MP-12MJ 50152-000 4-1-3

Fitting STR -16MP-16MJ 50153-000 4-1-4

Fitting STR-12MP-12MJ 50152-000 4-2-5

Flip tail cylinder 50145-000 2-1-28

Gauge, 5” sight 50157-000 4-1-5

Grommet 50196-002 5-1-2

Grommet 50196-002 5-2-2

Grommet 50190-000 5-3-1

Grommet 50190-000 5-4-1

Holding valve block port 50161-019 4-6-19

Holding valve block port 50161-029 4-6-29

Hose and fitting kit 50161-000 –

Hydraulic filter assembly 50089-000 –





Hydraulic tank assembly 50030-000 2-1-1

Hydraulic tank assembly 50030-000 –

In/outlet for filter 50161-021 4-6-21

Inlet adapter for pressure gauge 50161-018 4-6-18

Junction assembly 50828-000 –

Junction box filler plug 50471-000 4-4-4

Junction box surface mount 50470-000 4-4-3

Junction mount plate 50777-000 4-4-1

Latch hanger plate 50062-000 2-1-8

Left dove tail cylinder 50136-000 2-1-6

Left dove tail cylinder mount weldment 50108-000 2-1-11

Left flip tail cylinder mount 50060-000 2-1-30

Light 50196-001 5-1-1

Light 50197-001 5-2-1

Light 50192-000 5-3-2

Light 50191-000 5-4-2

Linkage bar 50130-000 2-1-32

Lower cylinder pin 50120-000 2-1-31

Marker lamp assembly, red 50189-000 –

Marker lamp assembly, yellow 50189-001 –

Nut #10-24UNC hex lock 10908-003 4-4-12

Nut 1/4-20UNC reg hex 10900-004 4-4-15

Nut 3/8-16UNC reg hex 10900-006 4-4-8

Nut for bulkhead fittings 50161-026 4-6-26

Pivot pin 5” 50104-000 2-1-24

Pivot pin 7” 50112-000 2-1-23





Plug 50196-003 5-1-3

Plug 50196-003 5-2-3

Plug 50193-000 5-3-3

Plug 50193-000 5-4-3

Plug hex SOC -04MB 11699-003 4-3-3

Plug hex SOC -08MB 11699-006 4-3-2

PTO pump 50183-000 2-1-5

Pump pressure outlet 50161-027 4-6-27

Pump suction inlet 50161-028 4-6-28

Pump to tank 50161-013 4-6-13

Pump to valve bank inlet 50161-017 4-6-17

Pump to valve body 50161-010 4-6-10

Rear plate to flip tail 50161-003 4-6-3

Rear plate to flip tail 50161-004 4-6-4

Retractor bar 50118-000 2-1-25

Retractor bracket 50113-000 2-1-27

Return to tank from filter 50161-022 4-6-22

Right dove tail cylinder 50137-000 2-1-7

Right dove tail cylinder mount weldment 50107-000 2-1-10

Right flip tail cylinder mount 50061-000 2-1-29

Screw #10-24UNC PHM x 3/4” 10253-006 4-4-11

Screw 1/2-13UNC HHC x 2-1/4” 10004-018 2-2-5

Screw 1/4-20UNC HHC x 1” 10000-008 4-2-4

Screw 1/4-20UNC HHC x 3/4” 10000-006 4-4-14

Screw 3/8-16UNC FSHC x 2-1/2” 10156-020 4-4-9

Spacer 50123-000 2-1-12





Spacer 50100-004 2-1-26

Spacer, short 50155-000 2-1-33

Strain relief 3/4” 50473-000 4-4-5

Tail idler pin 50122-000 2-1-18

Tail idler roller 50125-000 2-1-19

Tail idler weldment 50093-000 2-1-9

Tail latch weldment 50100-000 2-1-21

Tail light assembly 50196-000 –

Tail support tube 50119-000 2-1-22

Tank suction to pump 50161-023 4-6-23

Tool box assembly 50641-000 2-1-4

Toolbox 50116-001 2-3-1

Toolbox assembly 50641-000 –

Toolbox mount angle 50755-000 2-3-2

Toolbox mount weldment 50642-000 2-3-3

Valve bank outlet to filter 50161-016 4-6-16

Valve bank to bed 50161-001 4-6-1

Valve bank to wall dove tail 50161-024 4-6-24

Valve bank to wall flip tail 50161-025 4-6-25

Valve bank to winch 50161-002 4-6-2

Valve block to holding valve block 50161-030 4-6-30

Wall to dove tail cylinder 50161-005 4-6-5




Wall to valve 50161-009 4-6-9





Washer #10 SAE flat 11001-003 4-4-10

Washer 1/2” SAE flat 11001-008 2-2-4

Washer 1/4” SAE flat ASTM 11001-004 4-2-3

Washer 1/4” SAE flat ASTM 11001-004 4-4-13

Washer 3/8” SAE flat 11001-006 4-4-7

Weldment, hydraulic tank 50039-000 4-1-1

Winch angle weldment 50635-000 2-2-1

Winch assembly 50636-000 2-1-3

Winch assembly 50636-000 –

Winch motor 50161-014 4-6-14

Winch, 9000 lb 50146-000 2-2-2

Winder, winch level 50147-000 2-2-3

Contact

Xtreme Manufacturing 1415 West Bonanza Road

Las Vegas, NV 89106 (702) 851-3750


Sales (702) 858-2404

Product Support (702) 636-2969

Engineering (702) 851-3750


December 7, 2007 Preliminary Manual Warranty-1

Limited Warranty

Products Warranted

This Limited Warranty applies to new Xtreme Manufacturing brand Easy Loaders bearing the Xtreme Manufacturing trademarks, herein referred to as Product(s), which are marketed by Xtreme Manufacturing.

Warranty Period

Xtreme Manufacturing Warrants, its Authorized Sales and Service Centers (herein referred to as “SSC”), new Product(s) to be free from defect in material or manufacture for thirty-six (36) months after date of delivery to the purchaser, except the engine which will be covered for twenty-four (24) months. Additionally, the main frame shall be free from defect in material or workmanship for ten (10) years. This Warranty is made to the original owner of the new Product(s) and is transferable for the duration of the period of coverage, to subsequent owners with prior written approval of Xtreme Manufacturing (See Limitations).

Coverage

The Xtreme Manufacturing SSC shall repair or, at Xtreme Manufacturing's option, replace any Product(s) shown to be defective in material or manufacture. Xtreme Manufacturing shall pay to the extent it has established in its applicable service policy in effect at the time of delivery of the Product(s), the cost of labor reasonably necessary to install any repaired or replaced part provided under this Warranty. The remedies set forth in this paragraph are exclusive and correction by Xtreme Manufacturing or its SSC of Product non-conformities in the manner provided above shall constitute fulfillment of all liabilities and obligations of Xtreme Manufacturing or its SSC to those entitled to the benefit of this Limited Warranty.

Exclusions

This Limited Warranty shall not apply to general maintenance services (including but not limited to, engine tune-up, brake adjustment, etc.) or to general maintenance parts (including but not limited to, fluids, lubricants, light bulbs, etc.). In addition, this Limited Warranty shall not apply to parts/options not manufactured by Xtreme Manufacturing which are warranted by their respective manufacturers including but not limited to engines, tires, batteries, etc.

Owner Responsibilities

The owner is responsible for proper maintenance of the products(s). Any improper use including failure to provide proper maintenance, operation after discovery of defective or worn parts, operation beyond rated capacity, substitution of parts not approved by Xtreme Manufacturing, alteration or repair in such a manner as in Xtreme Manufacturing's judgment adversely affects the Product(s), shall void this Warranty, if requested by Xtreme Manufacturing, product(s) or parts, for which a warranty claim is made, are to be returned, freight prepaid, to Xtreme Manufacturing.


December 7, 2007 Preliminary Manual Warranty-2

Limitations

Xtreme Manufacturing's obligation under this Limited Warranty is expressly limited to the conditions as stated above and shall not include duty, taxes, or any other charges whatsoever, or any liability for direct, indirect, incidental, or consequential damage or delay. XTREME MANUFACTURING MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. No employee or representative is authorized to change this Warranty in any way or grant any other Warranty, unless such change is made in writing and signed by an officer of Xtreme Manufacturing.

Applicable Law

This Warranty shall be govemed by and interpreted in accordance with the laws of the State of Nevada. This Warranty is applicable to contracts made and performed in Nevada.

Contact

Xtreme Manufacturing, LLC 1415 West Bonanza Road

Las Vegas, NV 89106 (702) 851-3750


Sales (702) 858-2404

Product Support (702) 636-2969

Engineering (702) 851-3750 (702) 646-2196 (fax)

MODEL NO. ____________________

SERIAL NO. ____________________

Illustrated Parts Breakdown Manual EZ LOADER Model · PDF fileEZ LOADER Model EZ18 ... Tail...

Documents

Transcript of Illustrated Parts Breakdown Manual EZ LOADER Model · PDF fileEZ LOADER Model EZ18 ... Tail...