IJERA 012202218X
-
Upload
chetan2042 -
Category
Documents
-
view
221 -
download
0
Transcript of IJERA 012202218X
-
8/6/2019 IJERA 012202218X
1/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
202 | P a g e
Evaluation of an Electric Vehicle Performance under DifferentModes of Operations: Experimental Study
M. R. El- Sharkawy*, M. A. Mourad
*, M. M. M. Salem
*, M. M. Youssef
*
*Automotive and Tractors Engineering Department, Faculty of Engineering,
Minia University, Minia, Egypt.
Abstract
In recent years, Electric Vehicles (EVs) have become a production viable and
effective mode of efficient transportation. Electric Vehicles (EVs) can provide increased
fuel economy and reduced harmful emissions over convention technology vehicles. In this
study, the electric vehicle (EV) was tested to check its performance using a certain
procedures. The tests described in this study are "No Load Tests", "Load tests" and "On-
road Performance Evaluation Tests". All these tests allow evaluating the power and energy
consumption by the electric vehicle during different modes of operations. The battery
voltage and current were recorded during the different tests to allow plotting the
requirements. The vehicle has been demonstrated to be very reliable and all the presented tests
showed excellent results regarding system behavior and efficiency. Some of the
performance characteristics of this Electric Vehicle are: maximum speed is nearly about 60
km/h at the top gear with 1.78 m/s2 acceleration. The vehicle can carry two passengers
comfortably seated inside cabin. The DC traction motor was connected directly to theconventional mechanical transmission, which allows to give 15 HP at 3200 rpm, and 72
Volt input and that is more reliable and suitable for the tested vehicle. For the constructed
electric vehicle, the available and suitable type of batteries is the US 8VGC XC deep cycle
lead acid batteries for the 8 V 170 amp hours (AH). According to the calculations, we were
able to fit eight batteries in our vehicle. This would give a battery pack of 10.88 kWhr. We
have them configured in two rows of eight series connected batteries creating a battery
pack of 64 V and 170 AH. All the instrumentation for the driver panel was implementeddigitally, given information about battery current, battery voltage, and rpm of the motor.
Key Words: Electric Vehicles, Performance Evaluation, DC Electric Motor, Lead Acid
Battery.
1. Introduction
Vehicles have improved over long years. They became more versatile, better in
performance and more comfortable without increasing the purchase cost, which has lead to
unprecedented increase in number of vehicles on the road; this increase in the number of
vehicles together with raising understanding of their environmental impacts and
sustainability provided motivation for current discussion on future mobility [1]. However,
most researchers attempt to present an enhancement processes in an attempt to find answer
of this problem. In recent years, a significant interest in alternative vehicles such as Battery
Electric Vehicles (BEVs) and Hybrid Electric Vehicles (HEVs) have arisen globally due tothe pressing environmental concerns and skyrocketing price of oil [2].
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
2/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
203 | P a g e
Electric vehicles (EVs) have existed for over a hundred years. At the start of the 20 th
century electric vehicles must have looked a strong contender for future road transport [3]
due to the environmental and economical issues which provide a compelling impetus to
develop clean, efficient, and suitable vehicles for urban transportation [4].When they were invented, they immediately provided an economical and reliable means of
transportation. However, electric vehicles were plagued by poor range and short-lived
batteries. Today, a renewed interest in environment and energy independence has
compelled industry and government to again pursue electric vehicle designs. These designs
focus on improving the range, efficiency, and durability of EVs [5].
Electric vehicles have improved their performance and made suitable for commercial and
domestic use during the last decades. Nevertheless, pure electric vehicles still have not
achieved ranges comparable to that of gas powered conventional vehicles, this problem,
due to the low energy density and specific energy contained in most electric batteries
compared to that of gasoline, is resolved in hybrid vehicles by combining high energy
density of gas or hydrogen and high efficiency of electric drive systems [6]. Finally, theelectric vehicles (EVs) can be safer than oil-powered vehicles [7].
2. Vehicle Testing (Practical Work)
2.1 Introduction
The vehicle testing was carried out in the Vehicle Research Laboratory, Automotive and
Tractors Engineering Department, Faculty of Engineering, Minia University. The different
tests were carried out using the protocol in the Code of world Regulations
The following section presents the results obtained from the experimental work carried out
in this study. Extensive testing was carried out over a prolonged period of time.
2.2 Performance Evaluation Tests
The electric vehicle (EV) was tested to check its performance using a certain procedures.
The tests described in this study are "No Load Tests", "Load tests" and "On-road
Performance Evaluation Tests". All these tests allow evaluating the power and energy
consumption by the electric vehicle during different modes of operations. The battery
voltage and current were recorded during the different tests to allow plotting the
requirements. These tests assume that the battery has been discharged from full to around
80% of the full charge state. The most interesting results in this study are the power and
energy consumed by the vehicle.
2.3 No Load Tests (Primary Tests)
In these tests, the vehicle operates without any loads acting on the wheel, while the volt
and current drained from the battery and consumed by the vehicle were recorded. In
addition, the battery volt, current and power was measured during a short period of time.
Figure (1) shows the variation of battery voltage, battery current and battery power versus
vehicle speed at no load on the wheel. With respect to battery voltage, it has been shown
that increasing of vehicle speed resulted in a decrease in the voltage due to the drain of the
battery because it operates without a recharging source.
The battery current decreases with the increasing of vehicle speed; this is also due to theincreasing of the load with vehicle speed increased.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
3/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
204 | P a g e
On the other hand, the power consumed by the vehicle increased due to increasing the
vehicle speed because of the increasing of internal resistance of the transmission set.
Figure (2) shows the variation of battery voltage, battery current, battery power and energy
consumed versus time. This test was carried out during a short period of time to evaluatethe state of the battery along the time of operation. It is observed that the battery voltage,
current and power reduced along the period of operation, on the other hand the amount of
energy consumed increased.
Battery voltage, current, and power with Vehicle Speed at no load on wheels
0
10
20
30
40
50
60
70
80
50 70 90 110 130 150 170 190 210
Vehicle Speed, km/h
Batteryvoltage
,current,andpower
Voltage, V
Current, A
Power, kW
Figure (1) Battery current, voltage and power with vehicle speed, at no load on the wheel.
Battery voltage, current, power, and energy with Time at no load
0
10
20
30
40
50
60
70
80
90
100
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,andenergy
Voltage, VCurrent, A
Power, kW
Energy, Wh
Figure (2) Battery current, voltage, power, and energy during a short period of time.
Another tests were carried out at the mode of no load acting on the vehicle are the battery
voltage, current, power and energy consumed with different gearshifts versus time. The
following figures 3, 4, 5and 6 illustrates the variations of battery voltage, current, and the
power and energy consumed by the vehicle during a certain period of time with a different
gear shifts at no load acting on the vehicle during the tests. Finally, a comparison between
power and energy consumed by the vehicle at different gearshifts was presented and the
results show that the increasing of vehicle speed resulted in increasing of power and energy
consumption as shown in figures 7 and 8. Moreover, the average power and energy
consumed during the tests at the cases of different gear shifts were calculated, and the
figures 9 and 10 show the results. Table (1) shows the average power and energy
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
4/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
205 | P a g e
consumption by the electric vehicle with different gearshifts at no load affected on the
wheels.
Gearshifts 1st Gear 2nd Gear 3rd Gear 4th Gear
Power (kW) 2.968 3.027 3.229 3.856
Energy (Wh) 53.028 53.972 57.514 67.301
Battery voltage, current, power, and energy with Time, at 1st
gear with no load on the wheels
0
20
40
60
80
100
120
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,an
denergy
Voltage, V
Current, A
Power, Kw
Energy, Wh
Figure (3) Battery voltage, current, power, and energy with Time, at 1st gear with no load on the wheels
Battery voltage, current, power, and energy with Time, at 2ndgear with no load on the wheels
0
20
40
60
80
100
120
0 20 40 60 80 100 120 140
Time, S
Ba
tteryvoltage,current,power,andenergy
Voltage, V
Current, A
Power, Kw
Energy, Wh
Figure (4) Battery voltage, current, power, and energy with Time, at 2nd gear with no load on the wheels.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
5/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
206 | P a g e
Battery voltage, current, power, and energy with Time, at 3rdgear with no load on the wheels
0
20
40
60
80
100
120
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,andenergy
Voltage, V
Current, A
Power, kW
Energy, Wh
Figure (5) Battery voltage, current, power, and energy with Time, at 3rd gear with no load on the wheels.
Battery voltage, current, power, and energy with Time, at 3rd
gear with no load on the wheels
0
20
40
60
80
100
120
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,andenergy
Voltage, V
Current, A
Power, kW
Energy, Wh
Figure (6) Battery voltage, current, power, and energy with Time, at 4th gear with no load on the wheels.
Comparison between Power consumed by the vehicle at different gears with Time at no load on thewheels
2.5
2.7
2.9
3.1
3.3
3.5
3.7
3.9
4.1
4.3
4.5
0 20 40 60 80 100 120 140
Time, S
BatteryPowerConsumed,kW
1st gear Power, kW
2nd gear Power, kW
3rd gear Power, kW
4th gear Power, kW
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
6/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
207 | P a g e
Figure (7) Comparison between Power consumed by the vehicle at different gears with Time at no load on
the wheels
Comparison between Energy consumed by the vehicle at different gears with time, at no load on the
wheel
0
20
40
60
80
100
120
140
0 20 40 60 80 100 120 140
Time, S
BatteryEnergyConsumed,
Wh
1st gear Energy, Wh
2nd gear Energy, Wh
3rd gear Energy, Wh
4th gear Energy, Wh
Figure (8) Comparison between Energy consumed by the vehicle at different gears with time, at no load on
the wheel
Average power consumed with gear shifts at no load on wheels
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
1st gear 2nd gear 3rd gear 4th gear
Gear Shifts
AveragePowerconsum
ed,kW
Figure (9) the average power consumed with gearshifts at no load on wheels.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
7/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
208 | P a g e
Average energy consumed with gear shifts at no loads on wheels
0
10
20
30
40
50
60
70
80
1st gear 2nd gear 3rd gear 4th gear
Gear Modes
AverageEnergyconsumed,Wh
Figure (10) the average energy consumed with gearshifts at no loads on wheels.
2.4 Chassis Dynamometer Tests (Load Tests)
The same tests described in the previous case were conducted on a chassis dynamometer to
simulate the vehicle loading action during the tests. In this case, the rolling resistance only
was considered as the load acting on the vehicle and the voltage, current, power and energy
consumption were recorded according this condition.
Figure (11) show the relations between battery voltage, current and power with vehicle
speed at a certain load condition (rolling resistance only was considered). It is observed
that the battery voltage decreased with increasing the vehicle speed due to the drain
mechanism of the battery without recharging source. In addition, the battery currentincreased as the vehicle speed increases to compensate the energy consumed to overcome
the motion resistance of the vehicle. Finally, the power consumption significantly increases
with vehicle speed.
Battery voltage, current, and power with vehicle speed at load, (Rolling resistance),
chassis dynamometer.
0
20
40
60
80
100
120
20 25 30 35 40 45 50 55 60 65 70
Vehicle Speed, km/h
Batteryvoltageandcurrent
0
1
2
3
4
5
6
BatteryPowerkW
Voltage, V
Current, A
Power, kW
Figure (11) Battery voltage, current, and power with vehicle speed at load, (Rolling resistance)
In addition, a set of tests were carried out at the mode of load condition acting on the
vehicle are the battery voltage, current, power and energy consumed with different
gearshifts versus time. Figures 12, 13, 14 and 15 illustrates the variations of battery
voltage, current, power and energy versus time at different gear shifts. The load considered
in this case is the rolling resistance, which simulated by using the chassis dynamometer
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
8/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
209 | P a g e
device. Moreover, a comparison between the power and energy consumption by the
vehicle during the selected period at different gear shifts were carried out and the following
figures 16 and 17 demonstrate these variations and the results show that the increasing of
vehicle speed resulted in increasing of power and energy consumption. Finally, the average power and energy consumed during the tests at the cases of different gear shifts were
calculated, and the figures 18 and 19 show the results.
Table (2) shows the average power and energy consumption by the electric vehicle with
different gearshifts at load considered from rolling resistance.
Gearshifts 1st Gear 2nd Gear 3rd Gear 4th Gear
Power (kW) 3.655 3.929 4.115 4.342
Energy (Wh) 64.740 69.505 70.202 73.756
Battery voltage, current, power, and energy with Time, at 1stgear with load on the wheels, (Rolling
resistance), on chassis dynamometer
0
20
40
60
80
100
120
140
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,andenergy
Voltage, V
Current, A
Power, kW
Energy, Wh
Figure (12) Battery voltage, current, power, and energy with Time, at 1st
gear with load on the wheels,
(Rolling resistance)
Battery voltage, current, power, and energy with Time, at 2nd
gear with load on the wheel,
(Rolling resistance), on chassis dynamometer
0
20
40
60
80
100
120
140
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,andenergy
Voltage, V
Current, A
Power, kW
Energy, Wh
Figure (13) Battery voltage, current, power, and energy with Time, at 2nd gear with load on the wheel,
(Rolling resistance)
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
9/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
210 | P a g e
Battery voltage, current, power, and energy with Time, at 3rd
gear with load on the wheels, (Rolling
resistance), on chassis dynamometer
0
20
40
60
80
100
120
140
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power,andenergy
Voltage, V
Current, A
Power, kW
Energy, Wh
Figure (14) Battery voltage, current, power, and energy with Time, at 3rd
gear with load on the wheels,
(Rolling resistance)
Battery voltage, current, power, and energy with Time, at 4th
gear with load on the wheels, (Rolling
resistance) on chassis dynamometer
0
20
40
60
80
100
120
140
0 20 40 60 80 100 120 140
Time, S
Batteryvoltage,current,power
,andenergy
Voltage, V
Current, A
Power, kW
Energy, Wh
Figure (15) Battery voltage, current, power, and energy with Time, at 4th
gear with load on the wheels,
(Rolling resistance)
Comparison between Power consumed by the vehicle at different gears with Time at load on the
wheels, (Rolling resistance), on chassis dynamometer
2.5
3
3.5
4
4.5
5
5.5
6
0 20 40 60 80 100 120 140
Time, S
BatteryPowerConsumed,kW
1st gear Power, kW
2nd gear Power, kW
3rd gear Power, kW
4th gear Power, kW
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
10/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
211 | P a g e
Figure (16) Comparison between Power consumed by the vehicle at different gears with Time at load on the
wheels, (Rolling resistance)
Comparison between Energy consumed by the vehicle at different gears with time, at load on the
wheel, (Rolling resistance), on chassis dynamometer
0
20
40
60
80
100
120
140
0 20 40 60 80 100 120 140
Time, S
BatteryEnergyConsumed,Wh
1st gear Energy, Wh
2nd gear Energy, Wh
3rd gear Energy, Wh
4th gear Energy, Wh
Figure (17) Comparison between Energy consumed by the vehicle at different gears with time, at load on the
wheel, (Rolling resistance)
Average power with gear shifts at load, (Rolling resistance), on chassis dynamometer
3.2
3.4
3.6
3.8
4
4.2
4.4
1st Gear 2nd Gear 3rd Gear 4th Gear
Gear Shifts
BatteryPowerConsumed,kW
Figure (18) Average power with gear shifts at load, (Rolling resistance)
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
11/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
212 | P a g e
Average energy with gear shifts at load (Rolling resistance), on chassis dynamometer
60
62
64
66
68
70
72
74
76
1st Gear 2nd Gear 3rd Gear 4th Gear Gear Shifts
BatteryEnergyConsumed,Wh
Figure (19) Average energy with gear shifts at load (Rolling resistance)
2.5 On-road Performance Evaluation Tests
On-road evaluation of the implemented electric vehicle (EV) was conducted to determine
the battery characteristics, power and energy consumed by the vehicle during the normal
driving. Road testing was carried out at the faculty car parks and this enables us to
accelerate up to about 60 km/h by the tested vehicle. These tests have been introduced, for
power and energy consumption certification of the implemented electric vehicle atdifferent modes of operations according to road conditions. The test represents a driving
pattern, which includes a repetition of a basic cycle composed of idle, acceleration,
deceleration, and stop modes and the main characteristic parameters of this cycle are 600
sec. duration, maximum speed 43 km/h and average speed was nearly 28.5 (km/h). The test
was carried out on the vehicle and the amount of battery voltage, current, power and
energy were recorded. In addition, the vehicle speed and time during the test were taken
into account. Figure (20) shows the vehicle speed profile over the duration of the test
cycle. The results show that, the vehicle speed changes during the duration of the cycle
according to road conditions. As this shown the vehicle started the cycle at speed of 0
(km/h), and then increased due to the acceleration according to the road conditions, then
the vehicle speed decreased due to the deceleration, this deceleration may be because theusing of the brakes or due to an obstacles or for preparing to stop. From the results, the
maximum speed, which the vehicle reached, is 43 (km/h), and the average speed was 28.5
(km/h). Figure (21) show the variation of battery voltage versus time as a function of
vehicle speed during the test. It is observed that the battery voltage decrease along the
period of the test due to the drain of the battery without recharging sources.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
12/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
213 | P a g e
Vehicle Speed with Time
0
5
10
15
20
25
30
35
40
45
50
0 50 100 150 200 250 300 350 400 450 500 550 600 650
Time, s
VehicleSpeed,km/h
Vehicle Speed, km/h
Figure (20) vehicle speed with time (On-road test)
Vehicle Speed and Battery Voltage with Time
0
10
20
30
40
50
60
70
0 100 200 300 400 500 600 700
Time, s
BatteryVoltage,V
0
5
10
15
20
25
30
35
40
45
50
VehicleSpeed,km/h
Battery Voltage, V
Vehicle Speed, km/h
Figure (21) battery voltage with time as a function of vehicle speed
(On-road test)
Figure (22) show the variation of battery current versus time as a function of vehicle speed.
It is observed that the consumption of battery current increase with the vehicle speed
increase because of the increasing of the road resistance acting on the vehicle during
motion.
Vehicle Speed and Battery Current with Time
0
20
40
60
80
100
120
140
160
180
0 100 200 300 400 500 600 700
Time, s
BatteryCurrent,A
0
5
10
15
20
25
30
35
40
45
50
VehicleSpeed,km/h
Battery Current, A
Vehicle Speed, km/h
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
13/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
214 | P a g e
Figure (22) battery current with time as a function of vehicle speed
(On-road test)
Figure (23) show the variation of battery power consumed by the vehicle during the testversus time as a function of vehicle speed. It is observed that the power decrease along the
period of the test due to the drain of the battery.
Figure (24) show the variation of battery energy versus time as a function of vehicle speed.
The results obtained that the energy consumption increased with the time of usage.
Vehicle Speed and Battery Power with Time
0
1
2
3
4
5
6
7
8
0 100 200 300 400 500 600 700
Time, s
BatteryPower,Kw
0
5
10
15
20
25
30
35
40
45
50
VehicleSpeed,km/h
Battery Power, kW
Vehicle Speed, km/h
Figure (23) battery power with time as a function of vehicle speed
(On-road test)
Vehicle Speed and Battery Energy with Time
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0 50 100 150 200 250 300 350 400 450 500 550 600 650
Time, s
BatteryEnergy,kWh
0
5
10
15
20
25
30
35
40
45
50
VehicleSp
eed,km/h
Battery Energy, kWh
Vehicle Speed, km/h
Figure (24) battery energy with time as a function of vehicle speed
(On-road test)
From the results obtained, we can conclude that the average power and energy where theimplemented electric vehicle can consumed. Then, a long the presented test and according
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
14/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
215 | P a g e
to its characteristics the power and energy consumption during this period were as the
following table. Table (3) shows the average power and energy consumption by the electric
vehicle at on-road test for performance evaluation.
Power (kW) 4.025
Energy (Wh) 277.730
2.6 Maximum Speed Tests (On-road Tests)
These tests depending on conduct the vehicle at different gearshifts and trying to reach the
maximum speed of the vehicle at every gearshift.
During these tests, the time, vehicle speed, battery voltage, battery current, battery power
and battery energy were recorded until the vehicle reached to the maximum speed.
At the first gear the vehicle reached about 38 (km/h) and the duration of the test was 30
sec. Figure (25) show the variation of battery voltage, current, power and energy with timeas a function of the vehicle speed at the first gearshift. The results obtained that the
maximum acceleration of the vehicle during this case was 1.23 m/s2.
1st
Gear Vehicle Speed, Battery Voltage, current, power and energy with Time
0
10
20
30
40
50
60
70
80
90
100
0 5 10 15 20 25 30 35
Time, s
Batt
eryVoltage,current,powerandenergy
0
5
10
15
20
25
30
35
40
VehicleSpeed,km/h
1st Gear Bat tery Voltage, V 1st Gear Bat tery Cur rent , A 1st Gear Bat tery Power , kW
1st Gear Battery Energy, Wh 1st Gear Vehicle Speed, km/h
Figure (25) battery voltage, current, power and energy with time as a function of the vehicle speed at the first
gearshift.
At the second gear the vehicle reached about 43 (km/h) and the duration of the test was 30
sec. Figure (26) show the variation of battery voltage, current, power and energy with time
as a function of the vehicle speed at the first gearshift. The results obtained that themaximum acceleration of the vehicle during this case was 1.56 m/s2. At the third gear the
vehicle reached about 52 (km/h) and the duration of the test was 30 sec. Figure (27) show
the variation of battery voltage, current, power and energy with time as a function of the
vehicle speed at the first gearshift. The results obtained that the maximum acceleration of
the vehicle during this case was 1.78 m/s2. At the fourth gear the vehicle reached about 58
(km/h) and the duration of the test was 30 sec. Figure (28) show the variation of battery
voltage, current, power and energy with time as a function of the vehicle speed at the first
gearshift. The results obtained that the maximum acceleration of the vehicle during this
case was 2.06 m/s2.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
15/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
216 | P a g e
2nd
Gear Vehicle Speed, Battery Voltage, current, power and energy with Time
0
20
40
60
80
100
120
140
160
180
0 5 10 15 20 25 30 35
Time, s
BatteryVoltage,current,powerandener
gy
0
5
10
15
20
25
30
35
40
45
50
VehicleSpeed,km/h
2nd Gear Battery Voltage, V 2nd Gear Bat tery Cur rent , A 2nd Gear Bat tery Power , kW
2nd Gear Battery Energy, Wh 2nd Gear Vehicle Speed, km/h
Figure (26) battery voltage, current, power and energy with time as a function of the vehicle speed at the
second gearshift.
3rd
Gear Vehicle Speed, Battery Voltage, current, power and energy with Time
0
20
40
60
80
100
120
140
160
180
200
0 5 10 15 20 25 30 35
Time, s
BatteryVoltage,current,powerandenergy
0
10
20
30
40
50
60
VehicleSpeed,km/h
3rd Gear Battery Voltage, V 3rd Gear Bat tery Cur rent , A 3rd Gear Battery Power , kW
3rd Gear Battery Energy, Wh 3rd Gear Vehicle Speed, km/h
Figure (27) battery voltage, current, power and energy with time as a function of the vehicle speed at the
third gearshift.
4th
Gear Vehicle Speed, Battery Voltage, current, power and energy with Time
0
50
100
150
200
250
300
0 5 10 15 20 25 30 35
Time, s
BatteryVoltage,current,powerandene
rgy
0
10
20
30
40
50
60
70
VehicleSpeed,km/h
4th Gear Battery Voltage, V 4th Gear Battery Cur rent , A 4th Gear Battery Power , kW
4th Gear Battery Energy, Wh 4th Gear Vehicle Speed, km/h
Figure (28) battery voltage, current, power and energy with time as a function of the vehicle speed at the
fourth gearshift.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
16/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
217 | P a g e
Finally, the average power and energy consumption by the vehicle during this test were
determiner and the following figures show these results.
Table (4) shows the average power and energy consumption by the electric vehicle with
different gearshifts at maximum load tests.
Gearshifts 1st Gear 2nd Gear 3rd Gear 4th Gear
Power (kW) 3.720 4.740 6.372 7.347
Energy (Wh) 17.389 21.516 28.165 33.591
Average of power consumption at different gear shifts, on road test
0
1
2
3
4
5
6
7
8
1st G Power 2nd G Power 3rd G Power 4th G Power
Gear Shifts
Averageofpowercon
sumption,kW
Figure (29) average power consumption at different gearshift.
Average of energy consumption at different gear shifts, on road test
0
5
10
15
20
25
30
35
40
1st G Energy 2nd G Energy 3rd G Energy 4th G Energy
Gear Shifts
Averageofenergyconsumption,Wh
Figure (30) average energy consumption at different gearshift.
3. Conclusion
This paper makes an attempt to evaluate a battery electric vehicle and studying its
performance under different operating conditions. The study results have shown that, the
electric vehicle can meets the consumer expectations as well as environmental issues and
benefits, and other impacts like noise or local air-pollution. The vehicle has been
demonstrated to be very reliable and all tests presented showed excellent results regarding
system behavior and efficiency. The tested vehicle has a maximum speed of about 60 km/h
at the top gear with 1.78 m/s2 acceleration. The vehicle can carry two passengers
comfortably seated inside its cabin.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/ -
8/6/2019 IJERA 012202218X
17/17
M. R. El- Sharkawy, M. A. Mourad, M. M. M. Salem, M. M. Youssef/ International Journalof Engineering Research and Applications (IJERA) ISSN: 2248-9622www.ijera.com Vol. 1, Issue 2, pp.202-218
218 | P a g e
References
[1] Essam M. M. Allam, Nabil M. Hammad, Ahmad A. A. Saad, Shawki A. Abouel-
Seoud, " A Small City Series Hybrid Electric Vehicle : Performance Evaluation",
EET-2007 European Ele-Drive Conference Brussels, Belgium, May 30 June 01,
2007.
[2] Yuliang Leon Zhou "Modeling and Simulation of Hybrid Electric Vehicles",
master of applied science in the Department of Mechanical Engineering
University of Victoria, 2007.
[3] James Larminie, John Lowry, " Electric Vehicle Technology Explained", Book,
John Wiley & Sons Ltd, The Atrium, Southern Gate, Chichester, West Sussex
PO19 8SQ, England.
[4] Iqbal Husain, "Electric and Hybrid Vehicles", Design Fundamentals, Book, Boca
Raton London New York Washington, D.C, Published in the Taylor & Francis e-Library, 2005.
[5] Dimosthenis C. Katsis "Development of A Test bed For Evaluation of Electric
Vehicle Drive Performance", Masters of Science in Electrical Engineering, August
27, 1997 Blacksburg, Virginia
[6] Micah Ortzar, Juan Dixon (SM IEEE) and Jorge Moreno "Design, Construction
and Performance of a Buck-Boost Converter for an Ultracapacitor-Based
Auxiliary Energy System for Electric Vehicles", Department of Electrical
Engineering Pontificia Universidad Catlica de Chile Casilla 306, Correo 22,
Santiago.
[7] United States. Environmental Protection Agency (EPA). Transportation and Air
Quality Transportation and Regional Programs Division. EPA420-F-00-034,
March 2002.
http://www.ijera.com/http://www.ijera.com/http://www.ijera.com/