IDT MeshI/O · PDF filelink inductive loops, ThermiCam, RADIX magnetometer or similar...
2
ID T ID T MeshI/O TM wire-free detector linking MeshI/O™ is a system to transmit digital signals wirelessly. Based on IDT’s market-leading iMesh™ technology, MeshI/O provides an easy way to connect multiple remote, digital devices where cabling is not readily available or ducting is prohibitvely expensive. MeshI/O was developed to connect vehicle detectors to a downstream junction signal controller. A single upstream MeshI/O unit will support up to 6 digital inputs from inductive loops or other devices such as TrafiCam ® and Heimdall detectors. A second MeshI/O unit installed at the controller end of the link converts the wireless transmission to a digital output and provides screw terminals for connection to a Controller. Benefits and features Fully bi-directional Latency of just 3mS Compatible with any detector which has relay/opto-isolated/switched outputs Supports up to 6 inputs PLUS 6 outputs per end In-built fault detection sets UTC’s controller fault bit in the event of a dropped link Fully compatible with existing iMesh networks Can simultaneously provide mid-span mesh repeater function Avoids the need for expensive ducting OTU meshI/O (controller end) meshI/O (remote end) (containing iMesh router, 6 channels of digital inputs plus 6 channels of digital outputs, power supplies and antenna) Passive antenna Inductive loops (or any other detector with relay or opto-isolated outputs) (containing iMesh router, 6 channels of digital inputs plus 6 channels of digital outputs, power supplies and antenna) bi-directional iMesh wireless link
Transcript of IDT MeshI/O · PDF filelink inductive loops, ThermiCam, RADIX magnetometer or similar...
IDTIDT MeshI/OTM
wire-free detector linking
MeshI/O™ is a system to transmit digital signals wirelessly.
Based on IDT’s market-leading iMesh™ technology, MeshI/O provides an easy
way to connect multiple remote, digital devices where cabling is not readily
available or ducting is prohibitvely expensive.
MeshI/O was developed to connect vehicle detectors to a downstream junction
signal controller. A single upstream MeshI/O unit will support up to 6 digital
inputs from inductive loops or other devices such as TrafiCam® and Heimdall
detectors.
A second MeshI/O unit installed at the controller end of the link converts the
wireless transmission to a digital output and provides screw terminals for
connection to a Controller.
Benefits and features
Fully bi-directional
Latency of just 3mS
Compatible with any detector which has relay/opto-isolated/switched outputs
Supports up to 6 inputs PLUS 6 outputs per end
In-built fault detection sets UTC’s controller fault bit in the event of a dropped link
Fully compatible with existing iMesh networks
Can simultaneously provide mid-span mesh repeater function
Avoids the need for expensive ducting
OTU
meshI/O (controller end)
meshI/O (remote end)(containing iMesh router, 6 channels of digital inputs plus 6 channels of digital outputs, power supplies and antenna)
Passive antenna
Inductive loops (or any other detector with relay or opto-isolated outputs)
(containing iMesh router, 6 channels of digital inputs plus 6 channels of digital outputs, power supplies and antenna)
bi-directional iMesh wireless link
set a pelican or puffin wirelessly from a traffic signal controller
connect remote car park entrances and exits to a single, central car park occupancy counter
link two traffic signal controllers in a master-slave arrangement
link inductive loops, ThermiCam, RADIX magnetometer or similar detectors on multiple approaches to a junction controller
Example applications
© 2017 Integrated Design Techniques Limited. All rights reserved. Specifications included in this datasheet are subject to change without notice meshIO_3_220317.indd
TrafiCam and Heimdall are the trademarks of their respective owners
For further information on any of IDT’s products or to discuss how they can be used please contact us at:
IDT Ltd, Endurance House, Seventh Avenue, Team Valley, Tyne & Wear, NE11 0EF, United Kingdom
t: +44 (0)191 491 0800 e: [email protected] www.idtuk.com
About IDT
IDT is a leading provider of communication networks for smart cities and intelligent transport systems (ITS). Our iMesh networks delivery secure communications to over 5,500 traffic signal controlled junctions and our iCell routers are in over 2,500 UTMC-compliant variable message signs and other ITS assets.
QoS
Technical Specifications
Wireless Security
Firewall
10/100 MB Auto-switching (RJ-45 connectors)WAN portMDI/MDI-X Auto-switchingStatic IP or DHCP client
Environmental -15 to +70º C 5 – 95% RH IP54
Dimensions 168 x 123 x 44 mm (depth x width x height)
Weight 0.7 Kg
QoS
Internal option
General
Digital Six channels of digital (opto-isolated) inputs and outputs via screw terminals
Outdoor option
Digital Six channels of digital (opto-isolated) inputs and outputs via screw terminals
Dimensions
Weight 0.8 Kg
WPA2 AuthenticationMAC Address Access Control
Hidden SSID
VLAN
Netfilter - rule-based, multizone firewalling with NAT and masqueradePort forwarding
VPN (SSL & IPsec)
Reserved bandwidth and priority by application or IP address
268 x 268 x 86 mm (width x depth x height)with integral 15dBi directional antenna
Power 220Vac or Power over Ethernet
696726928
globalgroupISO 9001 5965
®
696726928
